Shower Bluetooth Speaker
Contents
1. 4 Ohm Audio Frequency 20Hz to 20 000Hz Responses NFC Connect For Bluetooth pair gt Z S Splash proof PX Operating Temperature R Disclaimer Updates to Firmware and or hardware components are made regularly Therefore some of the instruction specifications and pictures in this documentation may differ slightly from your particular situation All items described in this guide for illustration purposes only and may not Built In Battery 10 apply to particular situation No legal right or entitlements may be obtained from the description made in this manual S Service and Support For information www lenco com For support http lencosupport zendesk com Lenco helpdesk Germany 0900 1520530 Local charges The Netherlands 0900 23553626 Local charges 1ct p min Belgium 02 6200115 Local charges France 03 81484280 Local charges The helpdesk is accessible from Monday till Friday from 9 AM till 6 PM When contacting Lenco you will always be asked for the model and serial number of your product The serial number can be found on the back of the device Please write down the serial number below Model Boost 6 Serial number Lenco offers service and warranty in accordance to European law which means that in case of repairs both during and after the warranty period you should contact your local dealer Important note It is not possible to send products that need repairs to Lenco directly Important no2. when the battery is keeping low energy level in some minutes In this case the device cannot be turned On until you recharging the battery at least 10 15 minutes because the rechargeable battery has not enough energy M Use AUX IN Function In this design the Bluetooth module give priority to Bluetooth function as master the AUX In function is become slave if Bluetooth has been connected and in playing mode a Use AUX In under power ON mode Bluetooth un paired 1 Make sure that the external device has switched on and controlled to AUX output source with music playing 2 Slide the Power Switch 2 to ON position to turn on the device 3 Connect the Bluetooth Speaker s AUX IN 1 jack with an external device s Earphone AUX LINE jack output through the Audio cable 4 The mode will switch to AUX IN function automatically and the AUX IN 13 LED will turn On in green with blinking blue Now the Bluetooth Speaker s AUX In function is in use Use AUX In under Bluetooth music playing mode In Bluetooth music playing mode connect the Bluetooth Speaker s AUX IN 1 jack with an external device s Earphone AUX LINE Output through the Audio cable The AUX In 13 LED will turn On in green with blue 2 In this case the Bluetooth Speaker allow to switch over in between the AUX In mode and Bluetooth music playing mode by press the Pll
3. 9 button or tap the Pll icon on your mobile device 3 However the waiting time of mode change will taking about 3 10 seconds depending on mobile phone s OS example 3 seconds for Android s mobile device or 10 seconds for iOS s devices 4 Or press and hold the 8 button to quick switch to AUX IN mode if you want The Bluetooth will disconnect automatically 5 For Bluetooth reconnection tap Lenco Boost 6 in paired devices list on you mobile device Note the Bluetooth is staying at controlling mode at behind so that the Bluetooth mode LED is keep lighting or blinking in blue c To adjust volume level 1 Pressing or press and hold 10 button to decrease the volume 2 Pressing or press and hold 11 button to increase the volume N Splash proof Handling 1 Make sure that the splash proof Rubber Seal Cover 18 it tightens closed at the right position 2 The Bluetooth Speaker can handle a brief jet of water on its surface IPX4 Splash proof However it should never be operated under running water and under no circumstance it should never be fully immersed in water e oO 3 Always wipe the Bluetooth Speaker surface thoroughly if it becomes wet with moisture or water splashes This will help to prevent the internal parts of the unit from entry of water and possible moisture damage O Power Bank Function Charge Output DC 5V 1A max Before use the power bank function
4. All rights reserved
5. Lenco USER S MANUAL Boost 6 Bluetooth Stereo Speaker with Aux Input NFC amp Power Bank Splash proof For more information www lenco com Don ts e Do not place naked flames such as lighted candles on or near the product e Do not place objects filled with liquids such as vases on or near the product e Do not use or store this product in a place where it is subject to direct sunlight heat excessive dust or vibration Do not use this product with wet hands Do not clean this product with water or other liquids Do not block or cover the slots and holes in the product Do not push foreign objects into the slots or holes in the product Do not attempt to open this product yourself There are no user serviceable parts inside e Do not allow children access to plastic bags Safety Instructions Before using this product read and follow all warnings and instructions e This product is not intended for use by young children Young children should be properly supervised e This product is intended for household use only and not for commercial or industrial use e Do not expose to dripping or splashing e No naked flame sources such as lighted candles should be placed on the product e Ventilation should not be impeded by covering ventilation openings with items such as newspapers table cloths curtains and the like e Make sure the unit is adjusted to a stable position Damage caused by using this produ
6. Speaker if you wanted F Auto reconnect with paired device 1 Every time you turn On the Bluetooth Speaker s power it will firstly searching for the mobile device which has been paired previously and still in record The Bluetooth Speaker will reconnect this mobile device as priority if 5 it in Bluetooth searching device mode and in connection range 3 If no device found in some seconds then the Bluetooth Speaker will automatically turn into pairing mode 4 Now you can process for new mobile device pair refer to item D 3 D 6 methods Switch to new pairing from connected mode 1 In Bluetooth connected mode you can switch the Bluetooth Speaker into Bluetooth searching mode for paring with the new device at any time you desired 2 Press and hold the 8 button until a series of tones sound and the Bluetooth 13 LED will turn to fast blinking in blue from lighting 3 Now you can process for new mobile device pair refer to item D 3 D 6 methods Use NFC for fast Bluetooth pairing a On Bluetooth Speaker 1 Slide the Power Switch 2 to ON position 2 Make sure that the NFC detection mark nee 12 is at the right place to touch b On Mobile Phone 1 Make sure that the mobile phone has the NFC function turned on and the screen is active unlocked 2 Touch the mobile device NFC sensor on the Bluetooth Speaker s NFC detection mark Keep touching un
7. ct in an unstable position or by failure to follow any other warning or precaution contained within this user manual will not be covered by warranty Never remove the casing of this apparatus e Never place this apparatus on the other electrical equipment We suggest retaining the packaging in case for future transport of the product WARNING e Never remove the casing of this apparatus e Never place this apparatus on the other electrical AN equipment B Outlook and Controls Back View 1 2 3 4 5 Front View 13 16 17 1 AUX IN 3 5mm Jack Stereo Power Switch ON OFF CTL Button for Power Bank Type A USB Socket DC OUT DC 5V 1A 1000mA Micro USB socket DC Input DC 5V 2A 2000mA 6 Foot Stand MIC Position for hand free Button for Bluetooth Searching gt l Button Play Pause Pick up Hang up call Last dialed AUX Button Volume down Previous track Next track NFC Sensor Position for Bluetooth pair Mode LED 3 in 1 Charge Red Bluetooth Blue AUX IN Green Left Bass Radiator Right Bass Radiator Left Speaker Right Speaker Rubber Seal Cover for splash proof C About the rechargeable Battery This Bluetooth Speaker has an internal non user replaceable battery For best results the first time you use this Bluetooth Speaker let it charge for about 6 8 hours or until the charging LED indicator light from On to off which show you the battery is fully charged For maintain th
8. e battery life and performance if speaker isn t used for a while the battery might need to be recharged Charge the battery at least once every month To charge the rechargeable battery 1 Connect the Bluetooth Speaker s Micro USB socket 5 with the USB power charger which able to provides output at least DC 5V 2A for charge connection via the original USB cable supplied 2 The Charge 13 LED will turn On in red the battery is in charging 3 The Charge 13 LED will turn Off when the rechargeable battery is fully charged 4 Disconnect the USB cable when it is done Use a USB AC adaptor with following specs 5 volt 2 ampere When using lower ampere like 0 5A or 0 8 A the charging time will be 3 or 4 times longer Important The device design with high power of audio output and power bank function so it does not recommend you connect to computer s USB port for charging the Bluetooth Speaker as well as you use the Bluetooth operation at the same time It needs longer time to charge the battery fully and the Bluetooth Speaker will result works unstable or not proper working especially the internal battery energy is in lower level D Power ON and Pairing na a D Ba Slide the Power Switch 2 to ON position to turn On the device the Bluetooth searching reconnect function are open A series of tones will sound and the Bluetooth 13 LED is fast b
9. ic file play Press the 10 button to change previous music file play J Hand Free Function 2 OOS Di a When there is an incoming call during Bluetooth music playing mode The ringing sound will up and the playing music will pause automatically Press and hold f PI_ 9 button to reject the call if you want Or Press Pll 9 button to pick up the call Now you have hand free function with the Bluetooth speaker Press Pll 9 again to hang up the call when finished And the paused music will resume automatically Tip speak to the MIC 7 direct with distance in 30 60cm to get the best speakerphone performance when necessary K Redial For Last Call Function To redial for last called number by the Bluetooth Speaker even it is in music playing mode Press twice the f MI 9 button to enter into redial function the playing will pause and switch to hand free function for redial Press the Pll 9 Button again to hang up the redial call Make sure that your mobile phone has have last dial call used if not the redial for last call function cannot be activated Low Power Reminder And Auto Sleep The Bluetooth Speaker will send tones sound out from speaker by every 5 minutes When you heard this reminder please connect the device to the USB power for charging if you still want to use the device If not the Bluetooth Speaker will power Off to sleep mode
10. linking in blue Then activate the Bluetooth function in your Bluetooth device such as Mobile Phone or Personal Computer the device will enter to Bluetooth searching mode automatically if not tap the relate selection to manually enter to searching mode refer to your device s manual when necessary Your Bluetooth device should show Lenco Boost 6 in list and then select it for pairing Waiting for some seconds and you will see connected message as shown on your mobile device For some Bluetooth devices you may need to input 0000 as pairing password If pairing is successful a tone will sound and the Bluetooth 13 LED will keep lighting blue from blinking Now you can start to music play from the mobile device by its music player program Slide the Power Switch 2 to OFF position to turn Off the device when it is not in use E Disconnect from paired device i 2 3 P To disconnect with paired device and for better result turn Off the Bluetooth Speaker by slide the Power Switch 2 to OFF directly Or you can choose Disconnect from Bluetooth paired device list on your mobile device In this case the Bluetooth Speaker will turn back into Searching Pairing mode in seconds a series of tones will sound and the Bluetooth 13 LED will turn to fast blinking in blue from lighting Now you can process for new mobile device pair or power Off the Bluetooth
11. make sure that the Bluetooth Speaker s internal battery is full charged Or we recommended it has enough energy about 51 75 or more for charge the external device a Tocheck the battery remaining energy level 1 Press and hold the CTL 3 button the Charge 13 LED will light and or flashes in seconds for show the battery energy remaining levels 2 The Charge 13 LED will illumines as follow methods Long light for few seconds if battery about 90 100 energy Flashes 3 times then light off if battery about 51 75 energy Flashes 2 times then light off if battery about 26 50 energy Flashing fast then light off if battery below 25 energy b Power Bank Connection and Control 1 The Type A USB 4 socket is for charge output connection with DC 5V 1A max rating power 2 The Bluetooth Speaker s power bank charge output designed with auto detect feature it will turn ON the charge output function when you connected the external device s charge input into the Type A USB 4 socket 3 Besides the CTL 3 button also is a control to turn ON the charge output function manually for some needs However the charge output function will turn OFF automatically in 30 seconds if no device has connected 4 Press the CTL 3 button can turn ON the charge output function manually To charge your mobile device Plug the USB cable into the Power Bank s Type A USB s
12. ocket and then connect the other end of USB cable to the external device The power bank s charge output function will turn ON automatically 2 The Charge 13 LED flashing once at every 3 seconds the external device is in charging 3 After the external device is fully charged remove the USB cable the charge output supply will be cut off automatically in 30 seconds Important The Power Bank function cannot activate If the battery level is lower than 25 even you try to turn ON the power bank s charge output function at P Trouble Shooting e Check whether the device is in power OFF mode e Check whether volume level is in lower position on your Bluetooth speaker and mobile device e Make sure that your Bluetooth device is within the effective operation range No sound e Check whether the Bluetooth device is paired eCheck whether the Bluetooth device show connected eCheck if you have selected the correct audio source e Restart the speaker by power Off and On speaker Q Specification 250 mm L x 90 mm D x 101 5 mm H 850g Approximate V2 1 EDR Bluetooth Supported Profile A2DP AVRCP HSP Connection Distance In 10 meters open area Lithium 7 4V 4000mAh 3 7V 8000mAh type 18650 x 4pcs Playing Time 8 10 Hours at 75 80 of volume setting Power Source Input ee eee DC 5V 2A 2000mA Type A USB Port gt Power Bank Output Type A USB Port DC 5V 1A 1000mA 5W RMS x 2
13. te If this unit is opened or accessed by a non official service center in any way the warranty expires This device is not suitable for professional use In case of professional use all warranty obligations of the manufacturer will be voided This symbol indicates that the relevant electrical product or battery should not be disposed of as general household waste in Europe To ensure the correct waste treatment of the product and battery please dispose them in accordance to any applicable local laws of requirement for disposal of electrical equipment or batteries In so doing you will help 11 to conserve natural resources and improve standards of environmental protection in treatment and disposal of electrical waste Waste Electrical and Electronic Equipment Directive U CE Maring Products with the CE marking comply with the EMC Directive 2004 108 EC and the Low Voltage Directive 2006 95 EC issued by the Commission of the European Community Hereby STL Group BV Ankerkade 20 NL 5928 PL Venlo declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The declaration of conformity may be consulted at https lencosupport zendesk com forums 22413161 CE Documents This product operates at 2400 2483 5 MHz and is designated only to be used inside a normal household environment This product is suited for this purpose within all EU counties
14. til the mobile device vibrates and or sound When the devices connect some mobile phone may pop up a dialog box to confirm on it screen 3 After pairing is successful from Bluetooth speaker a tones will sound and the Bluetooth 13 LED will keep lighting in Blue from blinking 4 To disconnect the Bluetooth Speaker from an NFC connected phone touch it with the mobile device again Hint If you cannot connect the unit try the following Move the mobile phone slowly over the NFC mark of the Bluetooth Speaker f the mobile phone is in case especially metal remove it from the case Bluetooth Music Playing Controls two way function a On your Bluetooth Device 1 Switch to music player menu and choose a music to start the play from playlist or by using kK button icon Play Pause the playing music by using P Pll button icon 2 To adjust the volume level by using the device s volume control 6 Down Up button icon on your Bluetooth device refer to your device user s manual when necessary On Bluetooth Speaker In playing music press Pll 9 button to pause the playing music Press it again to resume Press and hold the 11 button to increases the volume level Press and hold the 10 button to decreases the volume level When maximum or minimum volume is reached a beep sound will be heard Press the 11 button to change next mus
Download Pdf Manuals
Related Search