LED Matrix light User manual ST-005
Contents
1. LED Matrix light User manual oI 005 please read the manual before installing and using this lighting Keep it for future reference Thank you for purchasing our product Upon receiving the lighting please Carefully check that there has been no damage caused in transportation If The lighting has been damage do not use the lighting and contact your Dealer or manufacturer This product complies with the following standards IEC60598 1 2003 IEC60598 2 1 7 1984 A2 1990 Main features 5 independent LEDs Built in programs 0 100 dimmer Four digital LED display control board Easy to set up lamp arrays Safety information DS important Al operation and maintenance must be carried out in accordance with this User manual Manufacturer will not with responsibility for that operation not according To this Instruction Verify that the voltage matches the rated voltage i i Dimensions Make sure power socket is connected with earth cable well The earth Cable of this unit is Yellow Green one always disconnect the power before attempting to open the equipment Housing or carrying out any maintenance do not connect power cable of other electric products with this unit Make sure power socket is connected with earth cable well The earth Cable of this unit is Yellow Green one do not expose the fixture to rain or moisture Verify that the feed cables are undamaged and rated for the current Make sure all devices are conne2. cted before use Keep all combustible materials for example fabric wood paper at least 0 3 meter away from the light Keep flammable materials well away from the fixture Al dimensions are in millimeter Avoid looking directly into the light source especially those who suffer from epileptic fits When it is thunderstorm don use the light and disconnect the power Power connection Supply high voltage will destroy light Verify that the voltage matches the rated voltage The highest ambient temperature is 40 C Make sure power socket is connected with earth cable well When suspending the fixture above ground level verify that the otructure can hold at least 10 times the weight of al installed devices Installing a Neutrik connector on a power cable Verify that all external covers and rigging hardware are securely Fastened and use an approved means of secondary attachment such as a safety cable Verify that all screws are tightly fastened Relaying power to other devices it The lightings can be linked in a chain by power cables which installed a blue and light gray connectors on the two ends The light gray connector Connects to the power out socket of the first lighting and the blue j Putbushing and chuck onto the cable nM connector connects to the power in socket of the subsequent lighting and Prepare cable as shown above The power cable must is a SO on three conductor 2 5m
3. it will be reset again SET DMX mode When the lighting is displaying the DMX address it runs in DMX mode and DRELD Reload default the lighting can be control by DMX512 signal b D ON bc OFF Control panel DMAAL Master stand alone setting b D MAST Master mode Buttons b ALON Stand alone mode SET ESC Call the main menu or escape the current menu i e return to Or parameter The upper menu and give up the selected item or parameter UP Browse the menu item forward or increase the parameter DOWN Browse the menu item backward or decrease the parameter ENTER Confirm the selected item or parameter i e enter the next 6 Menu or escape the current menu and save the selected item DAUSO Run mode when run built in program bD AUTO Auto bc SOUD Sound active DMIC Sound active sensitivity bc M20 Default 20 CSOFE Safe information DMX menu ADDR DADDR gt DMX address b A001 CCHS Selecting channels mode DSCH 5 channels mode default DICH 1 channels mode TD2CH 2 channels mode D4CH 4 channels mode C8CH 8 channels mode Adjustment menu ADJ DGDIM Gobal dimmer b C0 255 0 255 grayscale DLPOI LED 1 brightness b C0 255 0 255 grayscale DLPO2 LED 2 brightness b C0 255 0 255 grayscale DLPO3 LED 3 brightness b C0 255 0 255 grayscale DLP04 LED 4 brightness b C0 255 0 255 grayscale CLPO5 LED 5 brightness C 0 255 0 255 grayscale Static scene menu SCEN otatic
4. m cable Insert the wire into the terminals and fasten the clamping device by a flat screw driver Push insert and chuck into housing pay attention to the guiding keyway Fasten bushing the color coding schemes and some possible pin identification Schemes if pins are not clearly identified or if you have any doubts About proper installation consult a qualified electrician Wire color Conductor Symbol Brown Live L Blue Neutral Yellow green Ground c The power cable must is a three conductor 2 5mm cable Handling Iu Do not connect more than 40 lightings in total to AC mains power in one interconnected daisy chain Engagement Operation mode Menu Menu Navigation Stand alone mode In Stand alone mode the lighting out of control of any exterior SET MenuY ESCY A001Y ENTY DMX Menu signal run UPYZDN solely Enter SET menu to set the lighting to Stand alone mode SET MenuY ESCY CUSEY ENTY Adjustment menu Master slave mode UPYZDN oet one lighting to master device others to slave device so al SET MenuY ESCY SCENY ENTY Scenes menu lightings run UPYZDN synchronously flow the master device There must be only one master device in a chain You can set the lighting to master device SET MenuY ESCY PROGY ENTY Bult in program menu in the UPYZDN SET menu Press the menu to the DMX mode position the lighting WIIETED SET Menu in slave mode If the master lighting is pressed to DMX mode position
5. scenes DNOM Select scenes b c0 027 CGDIM Global dimmer C 000 255 Built in program menu PROG Built in program DPNU Select built in program b 001 020 DSPED Program speed b C0 255 O fastest 255 slowest CGDIM Gobal dimmer C 000 255 DMX protocol This lighting has 3 channel modes 1 channels mode 2 channels mode 4 Channels mode 5 channels mode 8 channels mode The default mode is 5 Channels Mode If you want to alter it enter DMX Menu 5 channels mode 000 255 LED 1 brightness 000 255 LED 2 brightness 000 255 LED 3 brightness 9 000 255 LED 4 brightness 000 255 LED 5 brightness 1 channels mode CH1 000 255 Strobe adjust 2 channels mode 000 255 Global dimmer 000 255 Adjust the bright time during strobe 4 channels mode 000 255 Global dimmer 000 255 Adjust the bright time during strobe 000 255 Adjust the blackout time during strobe 000 255 Built in programs and scenes 8 channels mode 000 255 Global dimmer 000 055 Strobe adjust 000 255 Built in programs and scenes 000 255 LED 1 brightness 000 255 LED 2 brightness 2403s 000 255 LED 3 brightness 000 255 LED 4 brightness 000 255 LED 5 brightness Speciation Voltage 230V AC 50 60Hz Power 70W Light source 5pcs 10Wwhite LEDs Dimmer 0 100 DMX control 1 2 4 5 8 selected by menu Working environment temperature 20C 40 C Net weight 2 5kg
Download Pdf Manuals
Related Search