Instruction of JA1000WH Laser Wheel Alignment Gauge
Contents
1. 34 FU LPT 041 FU PD 23 FU PD 64 FU PD 66 FU PD 58 TM2330 TM550 FU GC 2008 FU GC 30054 Laser Clase Crass2 Test Standards EN 60825 1 2007 The EUT described above has been tested by us with the listed standards and found in compliance with Directive 2006 95 EC It is possible to use CE marking to demonstrate the compliance with these LVD Directives The certificate applies to the tested sample above mentioned only and shall not knoty an assessment of the whole production It is only valid in connection with the Laser test report number TB LA123790 C Jema Autolifte A S Industrihegnet 2 4030 Tune Denmark www jemaautolifte dk E mail info jemaautolifte dk2. K Jens Danmark Jema Autolifte A S USER MANUAL Instruction of JA1000WH Laser Wheel Alignment Gauge Jema Autolifte A S Industrihegnet 2 4030 Tune Denmark www jemaautolifte dk E mail info jemaautolifte dk Somer Jema Autolifte A S USER MANUAL Mirror plate Standing arm Contact arms Contact arms Standing arm Standing arm Laser side gauge Scale plate Target plate A Mirror side gauge Thumb screw A Thumb screw B Laser operation button Preparation 1 Ensure the vehicle is standing on level ground and that the tire pressure is correct 2 Place the Laser side Gauge against the offside front wheel 3 Adjust the height of the Contact arms for the Laser side Gauge as near as possible to the wheel center 4 Adjust the width of the two Standing arm for the laser side gauge so that the contact arms are the same width as the wheel rim Jema Autolifte A S Industrihegnet 2 4030 Tune Denmark www jemaautolifte dk E mail info jemaautolifte dk Senmar Jema Autolifte A S USER MANUAL Calibration 1 Move the Laser side Gauge away from the wheel and place on a level surface Place the Mirror side Gauge opposite the Laser side Gauge Adjust the contact arms on the mirror side to the same height and width you have set for the Laser side by the four Contact arms touching Turn on the Laser operation button and the beam will project on to the mirror and return to the Ta
3. l rim 5 When the Laser beam is exactly on the center line of the Target plate the combined toe angle tracking of the vehicle can be read directly from the Scale plate in degrees minutes each division on the Scale plate is 10 minutes 6 To allow for possible lateral run out of the wheels move the vehicle forwards until the wheels have turned 180 one half of one revolution and repeat the procedure 7 If there is any difference in the result average the two readings Then check with the vehicle manufacturer s recommended tolerance Important Notes 1 We recommend that any adjustments to tracking should only be carried out by competent person 2 Never point the laser beam at a person 3 Never stare into the laser beam 4 Park with the front wheels pointing straight ahead Jema Autolifte A S Industrihegnet 2 4030 Tune Denmark www jemaautolifte dk E mail info jemaautolifte dk K J a Danmark Jema Autolifte A S USER MANUAL Shenzhen Toby Technology Co Ltd TORY 10F A Diock Asdo R 5 D Bidz No 5 Songpingstan Road Soence 4 Technology Part Nanshan Owtict Shenzhen China CERTIFICATE OF CONFORMITY No T812042851 Applicant Address Manufacturer Address Product Laser FU63511L5 GC 15 FUSS50A05 C4 FUBSOADS CB FUBSSADS CS a FUGSOLS 8010 FU650C5 S012 FU63511L100 8D16 Models FUBS5STILS BD22 FU63511CS 8022 FUGSO11L 100 8022 FU TSOZ FU AINIO2 FLEMINIOS FU LPT 012 FU LPT 021 FU LPT 0
4. rget plate If the laser beam is not on the Mirror the angle of projection can be adjusted by thumb screws A on the Laser side gauge If the laser beam is on the Mirror but not return on the Target plate the angle of projection can be adjusted by thumb screws A on the Mirror side gauge After the above step when the laser beam is on the target plate but not on the center white line of the Target plate turn around the scale plate to adjust it Check that the pointer is exactly over the zero of the scale plate If the pointer is not exactly on zero the Scale plate may be adjusted by slackening the thumb screw B and turn the pointer until the reading is exactly zero Then re tighten thumb screw B Jema Autolifte A S Industrihegnet 2 4030 Tune Denmark www jemaautolifte dk E mail info jemaautolifte dk Senmar Jema Autolifte A S USER MANUAL Operation 1 Place the Laser side Gauge against the offside front wheel of the vehicle with both contact arms just touching the wheel rim 2 Place the Mirror side Gauge against the near side front wheel with both contact arms just touching the wheel rim 3 Turn on the Laser button and the laser beam will project across the front of the vehicle on to the Mirror and back on to the Target plate 4 Turn around the Scale plate until the laser beam is on the center line of the target plate Be careful when adjusting the Scale plate not to disturb the positioning of the gauge against the whee
Download Pdf Manuals
Related Search