CANYON Two-Way Radios
Contents
1. check the charge LED light e It takes about to recharge the batteries fully if they ve become completely run down New batteries can take up to 14 hours to charge fully Battery life e The walkie talkie units have a built in Power Saver PS for maximum battery life but when not in use turn the unit OFF to conserve battery power e Remove the batteries if the units will not be used for a long period of time 3 Operation 3 1 Turning the Unit ON OFF 1 To Turn ON Press and hold the Power button A special beep sound will be heard and the LCD Screen will display the current channel 2 To switch OFF Press and hold the Power button A special beep sound will be heard and the LCD Screen will turn blank 3 2 Adjusting the Speaker volume There are 8 volume levels To adjust the speaker volume press the UP button to increase or press the DOWN button to decrease The LCD Screen will show the digital speaker volume level during adjustment 3 3 Receiving a Call The unit is continuously in Receive mode when the unit is turned ON and not transmitting When a signal is received on the current channel the receive signal icon RX will be displayed on the LCD Screen 3 4 Transmitting sending 1 Press and hold the TALK Push to Talk button to transmit your voice The transmit signal icon TX will display on the LCD Screen and the RED LED indicator will light 2 Hold the unit in a vertical position with th2. the channel scan will be deactivated OR press the UP button to continue the channel scanning 4 If no action is taken before the detected signal stops then the scan will continue 5 Press and hold the SCAN button to stop the channel scanning operation The unit will return to the channel set before the scan was started 3 7 The Menu Functions 3 7 1 Changing Channels The PMR has 8 available channels To change channel 1 Press the Menu button once the Channel icon 8 will start blinking on the LCD Screen 2 While the Channel icon is blinking press the UP or DOWN button to select the desired channel The channel changes from 1 to 8 or from 8 to 1 3 Press the TALK button again to confirm your selected channel 3 7 2 TX Power High Low setting This feature permits the selection of the transmitting power level to high or low At Power High the PMR will transmit at maximum power and at a longer transmission range ENG 4 Press the Menu button twice Press the UP or DOWN button to select High or Low The LCD Screen will display L when the low power is selected At low power mode the PMR will transmit at reduced transmitting range but could extend the battery life 3 Press the TALK button again to confirm your selected power level 3 7 3 Monitor You can use the Monitor feature to check for weak signals on the current channel 1 Press the Menu button 3 times The PMR will enter the Monitor mode and hear
3. CANYON Two Way Radios Article CNR WT3 USER MANUAL v1 0 Red LED I ndicator Antenna MENU Power button LCD Screen Up Down buttons Talk Push to Talk Mic Microphone Scan Button Call Button 1 LCD Screen Speaker an p TX Channel Number L a TX Transmitting a signal a Speaker volume level RX Receiving a signal L Power Low indicator 2 Fitting the batteries Your Walkie talkie includes a rechargeable battery pack for each handset Step 1 To remove the belt clip 1 It s easier to fit the battery pack without the belt clip in place 2 Pull the tab forward away from the handset to release the belt clip Then lift the belt clip off ENG 1 Step 2 To fit the batteries 1 Open the locking latch and slide off the battery compartment cover 2 Insert the rechargeable battery pack as shown 7 Make sure the UP arrow is showing and pointing towards the top of the handset 3 Replace the cover and close the latch Step 3 To replace the belt clip Slide the belt clip down into the slot until it clicks into place Insert your fingernail Lift the belt clip off behind the tab 7 5 EP PAFLF pe IMPORTANT Read these safety warnings before you charge the batteries 1 When placing the handset in the charger use only the rechargeable battery pack supplied with the walkie talkie 2 Don t try to fit or recharge non rechargeable batteries 3 Make sure
4. e Mic Microphone 5 10 cm away from ENG 3 the mouth While holding the TALK button speak into the mic microphone ina normal tone of voice 3 Release the TALK button when you have finished transmitting O0 Important 1 In order to receive your transmission other people must also be on the same channel that you are currently using Refer to the Changing Channel section for more information 2 When the TALK and or CALL buttons are continuously pressed your PMR cannot receive any transmissions 3 5 Calling Paging Tone You can use the CALL button to send a tone to other users on the same channel To activate this feature With the PMR in normal mode press and release the CALL button The unit will transmit a 2 second page tone to the other unit s set with the same channel within transmitting range 3 6 Channel Scan Channel scan performs a search for active signals in a continuous loop from channels 1 to 8 This allows you to find other radios without having to manually change to each channel To activate this feature 1 Press and hold down the SCAN button The channel number on the LCD Screen changes rapidly until an active signal is detected 2 When an active signal one of the 8 channels is detected the channel scan pauses on the active channel until the active signal stops 3 If you press the TALK button while the scan is paused on an active channel the unit will communicate through the active signal channel and
5. evel is low The RED LED indicator is flashing once in every 15 seconds The maximum range will vary depending on terrain and environment and depending on the TX power high low setting O Open fields provide the maximum range while steel concrete structures heavy foliage and use in buildings and in vehicles may limit the range significantly Wearing the radio close to the body such as in a pocket or on a belt will decrease range change the location of the radio Sound If you are transmitting speak in a normal tone of voice distortion 5 cm away from the Mic microphone problems If you are receiving lower the volume to a comfortable level Radios too close Radios must be at least 1 5 meters apart increase your distance Radios too far apart Obstacles interfere with transmission Talk range is up to 3 Km in clear unobstructed conditions ENG 6
6. everything on the current channel 2 Press the Menu button again to turn off the Monitor operation and return to standby mode 4 Auxiliary Features Channel Frequency Table 4 1 Power Saving Your PMR unit has special circuitry designed to extend the life of your battery When the unit is not used for 6 seconds it will automatically switch into a low power mode The Power Saving feature does not affect the PMR s ability to receive transmissions When a signal is detected it automatically returns to full power mode 4 2 Low Battery I ndicator The PMR can detect when the battery charge level gets low An alert tone will be heard and the RED LED indicator will flash once every 15 seconds When this happens replace the batteries Channel Frequency Table Channel Frequency MHz Channel Frequency MHz 446 00625 446 05625 446 01875 S oe 446 06875 446 03125 446 08125 446 04375 E n 446 09375 Troubleshooting Guide Check the batteries are installed properly The batteries may be weak Replace the old batteries with new ones Reception Press the UP button to increase the receiver volume level is weak The receiving signal may be weak and or out of range ENG 5 Cannot change channels To change channels press the Menu button once then press the UP or DOWN buttons to change the current channel Batteries may be weak Range is Batteries may be weak limited Replace with new batteries if the battery charge l
7. the battery compartment cover is securely locked in place when you re charging the batteries 4 Dispose of used batteries safely and in a way that will not harm the environment never try to burn them or put them anywhere they could get burnt or punctured 5 When you re not going to use your walkie talkie for a few weeks take the battery pack out so it doesn t leak corrosive substances 6 When the battery charge level gets low an alert tone will be heard and the RED LED indicator will flash once every 15 seconds When this happens recharge the batteries 7 Don t leave dead batteries in your handset they might leak if you do 2 1 Charging the batteries If you prefer to wall mount the charger use the template supplied Step 1 Connect the mains power lead to the charger Step 2 Plug the mains adapter into a 230 V AC 50 Hz mains socket with the switch on the socket set to OFF Step 3 Then switch on at the mains socket O The walkie talkie must be used with the mains adapter supplied Step 4 Place the handsets in the charging cradles ENG 2 The charge light comes on when a handset is in the cradle A oe i 0000 0 de AERE CNS 00 2 00 ss Battery Meter e The PMR can detect when the battery charge level gets low e An alert tone will be heard and the RED LED indicator will flash once every 15 seconds When this happens put it on the handset to charge pod and
Download Pdf Manuals
Related Search