User Manual 5
Contents
1. 6 RX Orange 7 Not Used White Brown 7 NotUsed White Brown 8 Not Used Brown 8 Not Used Brown Disclaimer GFE is not responsible for any typo misprint and grammatical errors on manuals or the boxing GFE reserves the right to change box manual and warranty information at anytime without warning GFE Tech support and RMA reserves the right to refuse service to anyone2. User Manual 5 Port Switch Table of Content 1 Product Introduction 2 Product Key Features 3 Package Content 4 Visual description and definition Pre installation 6 Installation 7 Installation verification 8 Cascading 9 Trouble Shooting 10 Switch Specification Sheet 11 Cable Specification Sheet 12 Warranty and Disclaimer Product Introduction This 5 Port Network Switch provides you with an economical high performance network switching solution for the home or small office It is designed to make network installations quick and easy With features such as auto negotiation the 5 Port Network Switch offers smooth network migration and easy upgrades to network capacity The auto uplink feature offers the users to expand their network with ease Key Product Features _ Five auto sensing 10 100 Mbps Ethernet ports using Category 5 Cat5 unshielded twisted pair UTP cable _ IEEE 802 3x standard compliant _ Automatic address learning function to build the packet forwarding information table _ Auto sensing full duplex or half duplex mode of operation Plug and Play installation with no software configuration required _ Wire speed filtering and forwarding to direct traffic to the appropriate port or network segment without speed reduction _ Front Panel LED s provide network traffic status and data transmission speed indicators _ Five RJ 45 ports on the rear panel reducing desktop cable clutter _ Auto Uplink function simpl
3. a replacement Switch Specifications Sheet Standard IEEE802 3 amp IEEE 802 3u Number of ports 5x 10 100Mbps Auto sensing RJ 45 ports Data Transfer Rate Ethernet 10Mbps half duplex 20Mbps full duplex Fast Ethernet 100Mbps half duplex 200Mbps full duplex Network Cables Unshielded twisted pair cable UTP cable Topology Star LED Indicators Per Device Power Per Port 100Mbps LINK ACT Transmission Method Store and forward MAC address table 1K entry MAC address table Maximum Forwarding Rate 64byte packets 14 880 pps 10BASE T 148 800 pps 100BASE T Maximum Filtering Rate 64byte packets 14 880 pps 10BASE T 148 800 pps 100BASE T Flow control Pause frame Full duplex Back pressure Half duplex Duplex mode Supports both half duplex and full duplex mode Power Supply External power adapter DC 9V 1000mA Dimensions 110mm x 70mm x 19mm L x W x H Temperature Operating temperature Storage temperature 0 C to 45 C 32F to 113F 40 C to 70 C 22F to 140F Humidity 5 to 90 non conditioning EMI FCC Class B CE Mark Housing lron Buffer Memory 1 Megabyte MAC address table Up to 1K Cable Specification Sheet Since the 5 Port Network Switch has the auto uplink function it does not really matter whether or not the user uses a crossover cable or a straight through cable 5 Port Ne
4. ate ventilation To install the switch on a wall measure the distance between the mounting holes on the back of the switch and mark the wall to match that measured distance At the marked location screw into the wall two suitably sized screws Choose a location that is near the devices to be connected is close to a suitable electrical outlet and provides at least 50mm of space all around the switch for ventilation Installation 1 Install a 10 100Mbps 10 100Base TX network adapter card into every computer you want to attach to the network Make sure you install the Network adaptor drivers in accordance with the manufacturers directions 2 Prepare the twisted pair cables with RJ 45 plugs on each end Use Category 5 5e cable for all connections Make sure the cable length is less than or equal to no more than 100 meters 328 feet 3 Attach one end of the cable to the RJ 45 port of the computer s network adapter card and the other end to any available port of the 5 port Network Switch 4 Locate a suitably switched 120volt AC power outlet to plug in the supplied power pack 5 Insert the power pack into the power outlet 6 Connect the cable attached to the power pack adapter to the power inlet on the rear panel of the switch 7 Typical Network Sample Diagram Checking your installation When power has been applied to the switch it will display 1 The green power LED on the front panel is on 2 The green Link LED on each
5. connected port is on When the switch is connected and operating refer to the table in LED s for information about the LED s and their activity Cascading The Switch The 5 port Switch has the ability to detect weather this node is a client or another switch Using any type of cable the switch can communicate with the other end Technically speaking Switch has the technology that enables it self to cascade an unlimited amount of times So Plug and Play comes in and will grant you the access to connect as many switch as you want Just plug in the cable from one end to the other Troubleshooting LED not lighting up even thou cat5 cable plugged in 1 Check your power LED If not lit check power supply 2 Check your cat5 cables make sure its not broken or mis paired 3 Make sure that the computer is turned on and the lights on the back of network card are on 4 Make sure that the cat5 cable is completely plugged If the above methods still have not solved the problem then please contact RMA department to get a replacement LED lights up but 1 computer can t see the second computer 1 Make sure that your network cards are working and properly configured 2 Unplug the power supply and plugged it back in after 30seconds 3 Are you giving the switch enough space to breath Make sure there is at least 50mm of space around the switch If the above methods still have not solved the problem then please contact RMA department to get
6. ifies network extension and allows the switch to connect to another switch or hub using a straight through cable _ Palm sized case to save space _ Iron housing with choice of wall mounting slots or rubber feet Compliance with the Class B EMI standard to prevent interference with home and business equipment _ 3 year warranty Package contents 5 Port Network Switch AC DC Power Adapter 4 Rubber Feet Wall Screws Technical support card and Warranty Card Visual Definition Front panel LED STATUS CONDITION On Switch is receiving power Power Off Power has been disconnected mY On The connection speed is 100 Mbps Off The connection speed is 10 Mbps On Port has established a valid link Link Off There is no network connection Flashing Data packets being received and sent LED Rear panel The rear panel of the 5 Port Network Switch has five auto sensing 10 100 Mbps Ethernet ports and a power jack for connection of the supplied AC DC Adapter The 5 port Network Switch only supports unshielded RJ 45 twisted pair UTP cable Pre installation Before you install your switch prepare for the installation Make sure you will be operating the unit within the specified voltage and temperature limits To install your switch on a flat surface simply install the included rubber feet within the outlines on the bottom surface of the unit Ensure the switch is positioned with at least 50mm of space on all sides for adequ
7. twork Switch will have no problem with it Standard Straight Through Cable As long as the category 5 UTP cable is being used the Hub Switch side Adapter side Pin Pair Pin Pair 1 RX White Orange 1 RX White Orange 2 RX Orange 2 RX Orange 3 TX White Green 3 TX White Green 4 Not Used Blue wre enn nn nn nn nnn nn nn nn nn nn nnn nnn nnn nnn nnn 4 Not Used Blue 5 Not Used White Blue 5 Not Used White Blue 6 TX Green 7 6 TX Green 7 Not Used White Brown 7 Not Used White Brown 8 Not Used Brown 57 8 Not Used Brown Hub to Hub Crossover Cable Hub Switch side Hub Switch side Pin Pair Pin Pair 1 RX White Orange 1 TX White Green 2 RX Orange 2 TX Green 3 TX White Green 3 RX White Orange 4 Not Used Blue 4 Not Used Blue 5 Not Used White Blue 5 Not Used White Blue 6 TX Green
Download Pdf Manuals
Related Search