ZXT-120 - Eedomus
Contents
1. 5 Select your operation mode please refer to Listening Mode section Include or Exclude the unit from the existing Z Wave home control network with your primary controller Refer to your primary controller instructions to process the inclusion exclusion setup procedure When prompted by your primary controller click once on the PROG button The primary controller should indicate that the action was successful If the controller indicates the action was unsuccessful please repeat the procedure User can use either the primary controller or secondary controller should support configuration command class to setup the ZXT 120 AC code by the parameter 27 IR code number for built in code library please refer to code list for the parameter value then setup your AC control code Once the configuration and setup were completed the controller can use Z Wave s Thermostat commands class to control their IR controlled air conditioner with the ZXT 120 You can record down your device code under the below table for future reference after setting up the ZXT 120 correctly AC device programmed to your ZXT 120 Code no ZXT 120 Information How to get the NIF Node Information Frame on ZXT 120 setup Key eae LED Indication ep Status on ZXT 120 Press the PROG button on e LED flashes once the ZXT 120 then stay off ZXT 120 will report the supported command class Parameter No2. 7 120 Z Wave to AC Extender SPEAKS Table of Contents Introduction ces 3 Controller and Gateway Requirements 4 Built in IR code library 4 5 ZPPPEEEPREPEFREREBBREEERFEEUEEREPEEEERERERREREREFSESEEPEFRR 5 ZXT 120 Operations 6 Product Overview 7 Z Wave Remote Control 8 ZXAT 120 Information Ana 9 Listening Mode 10 IR Code Learning 11 Reset ZXT 120 to factory 12 13 MOUNTING THE ZXT 120 A 13 WIRELESS INFORMATION 16 ee 16 FREQUENTLY ASKED QUESTIONS 16 Z Wave Frequently Asked 16 TECHNICAL SPECI 5 18 CHECKING ACCESSORIES 23 FCC 07 1 SBPPEPREERPERAPERPEEEBEFFEREEFEFRFERFEREERUEEPREEFER 23 WARNINGS 23 CAUTION BEPPRERRBERFEREEREREEREEFEEEREREEEEEEEUEENERREFEREERFEERER 23 Z Extender 2 120 Z Wave to AC IR Extender Operating I nstructions Introduction The ZXT 120 is a Z Wave to air conditioner AC IR Extender Figure 1 and it works with
3. aimed at each other 1 3 inches apart Press and keep holding the LED flashes twice key on your original and then OFF equipment remote until learn code ZXT 120 reacted success OR LED flashes six times rapidly and then OFF learn code fail 1 3inches Original remote Figure 3 Learning setup Reset ZXT 120 to factory default Press and hold PROG button for 10seconds ZXT 120 LED will flash twice until reset process is completed Note This reset step will not affect the operation mode of ZXT 120 user should refer to Listening Mode section if you want to change the operation mode Important Information you are using Gateway or other Z wave controllers to operate ZXT 120 Please follow the instruction from the gateway or other controller You can check either the specifications in the manual of your ZXT 120 or also check online at www remotec com hk for a full list of products that can be used with your ZXT 120 INSTALLATION MOUNTING THE ZXT 120 TO A WALL MOUNTING LOCATION PRECAUTIONS Before mounting check the material and structure of the mounting location If the location does not have the proper material or structure the ZXT 120 can fall and cause injuries Use commercial items that best match the wall structure and material for the screws and other fixtures Do not mount near a kitchen counter humidifier or other location in which it can be ex
4. key holes in the bottom case Note 1 The reception sensitivity varies depending on the antenna direction Note 2 Before mounting to a wall be sure to fully read the precautions Obtain two screws suitable for the wall strength and material The screw size is shown in the figure below i MIN Sm a 8ing 7 Jane i MIN 3mm 1 8ins The positional relationship between the ZXT 120 key holes and the screw mounting positions are shown in the figure below Note 1 When mounting the screws to the wall leave a space between the wall and screw cap as shown in the figure 1 4 5mm 3 16ins 48 5mm 1 7 8ins Insert the ZXT 120 key holes onto the two screws mounted to the wall and then slide downward to secure in place After securing the ZXT 120 to the wall connect the USB Power or batteries and IR emitter cable to the ZXT 120 Note 1 Check that the ZXT 120 is firmly secured to the wall Note 2 Insert USB plug or batteries and IR emitter cable so that they are firmly connected to the ZXT 120 When removing the ZXT 120 from the wall lift up the ZXT 120 then pull it towards you Detach the main unit from the battery chassis by move toward to top position WIRELESS INFORMATION Wireless range This device has an open air line of sight transmission distance of 100 feet which complies with the Z Wave standards Performance can vary depending on
5. TYPE 1 TEMPERATURE VALUE HEAT mode Temperature COOL mode Temperature TEMPERATURE COMMAND_CLASS_THERMOSTAT THERMOSTAT_ SETTING _SETPOINT SETPOINT_SET DRY mode Temperature SETPOINT TYPE 10 TEMPERATURE VALUE THERMOSTAT_ COMMAND_CLASS_THERMOSTAT FAN SPEED FAN_MODE_SE FAN MODE 0 _FAN_MODE v1 FAN AUTO THERMOSTAT_ COMMAND_CLASS_THERMOSTAT FAN MODE 0 2 or FAN_MODE_SE _FAN_MODE v2 4 T THERMOSTAT_ COMMAND_CLASS_ THERMOSTAT FAN_MODE_SE FAN MODE 1 _FAN_MODE v1 FAN LOW 1 3 THERMOSTAT_ COMMAND_CLASS_ THERMOSTAT FAN_MODE_SE FAN MODE 1 _FAN_MODE v2 AUTO mode Temperature 2 3 FAN HIGH 3 3 SWING ON SWING AUTO SWING SWING OFF u NORMAL POWER LEVEL IR TRANSMISSION POWER LEVEL HIGH POWER LEVEL DISABLE ENABLE FRONT IR TRANSMISSION CONTROL COMMAND_CLASS_THERMOSTAT _FAN_MODE v2 COMMAND_CLASS_THERMOSTAT _FAN_MODE v1 COMMAND_CLASS_THERMOSTAT _FAN_MODE v2 COMMAND_CLASS_CONFIGURATI ON COMMAND_CLASS_CONFIGURATI ON COMMAND_CLASS_CONFIGURATI ON COMMAND CLASS CONFIGURATI ON COMMAND CLASS CONFIGURATI ON COMMAND CLASS CONFIGURATI ON COMMAND CLASS CONFIGURATI ON THERMOST FAN MODE SE THERMOSTAT_ FAN_MODE_SE T FAN MODE 5 FAN MODE THERMOSTAT_ FAN_MODE_SE T FAN MODE PARAMETER NO VALUE 1 PARAMETER NO 33 SIZE 1
6. VALUE 0 PARAMETER NO 27 SIZE 2 VALUE CODE PARAMETER NO CONFIGURATIO N_SET CONFIGURATIO N_SET CONFIGURATIO N_SET CONFIGURATIO N_SET PARAMETER NO 28 SIZE 1 VALUE OxFF PARAMETER NO 32 SIZE 1 VALUE 0 PARAMETER NO 32 SIZE 1 VALUE OxFF CONFIGURATIO N_SET CONFIGURATIO N_SET CONFIGURATIO N_SET BATTERY COMMAND_CLASS_BATTERY BATTERY_GET LEVEL VERSION COMMAND_CLASS_VERSION VERSION_GET MANUFACTURE MANUF ER COMMAND_CLASS_MANUFACTUR R_SPECIFIC_GE ER_SPECIFIC SPECIFIC TEMPERATURE COMMAND_CLASS_SENSOR_MUL SENSOR MULTI SENSOR TILEVEL LEVEL GET CHECKING ACCESSORIES After opening the cover of the packing box check that the following accessories are included e ZXT 120 Z Wave to AC IR Extender e Screws bottom cover x 2pcs e ZXT 120 User Manual download from our website e AC Code List download from our website FCC NOTICE This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation WARNINGS Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment RISK OF FIRE RISK OF ELECTRICAL SHOCK RISK OF BURNS The socket
7. any Z Wave compliant gateway or portable controller by translating Z Wave s Thermostat commands to AC IR control code User can set the IR code from the built in code library of ZXT 120 through the configuration commands or use the learning function of ZXT 120 through the UI on gateway ZXT 120 also built in a temperature sensor that allow to report your room temperature to home gateway It can be utilized to control or monitor your room temperature by your smart phone or PC while you are at office home anywhere or around the world Figure I ZXT 120 ZXT 120 can be configured as either Frequently Listening Routing Slaves FLiRS or Always Listening node after exclusion process FLiRS node type is targeted for battery operated applications and it will enter sleep mode frequently in order to conserve battery consumption that can provide the flexibility if there is out of 5Vdc power source Also user can place the unit in anywhere at home Always Listening node type is targeted for the needs of required a fast response application The installed location should come with 5Vdc power source Always Listening node can act as a repeater which will re transmit the RF signal to ensure that the signal is received by its intended destination by routing the signal around obstacle and radio dead spots ZXT 120 supports Network Wide Inclusion NWI and Explore Frames It also supports Z Wave networks with multiple gateways and control
8. high power mode or adjust the position of your external IR emitter Can I use 2 or more ZXT 120 in my house What is the max units if yes Yes and it is very depend on the capability of gateway controller For example gateway can supports up to 8 16 or 32 ZXT 120 ina network How to avoid the IR interference if I am using 2 identical air conditioners in same location but want to control them individually User can disable the Surround IR Output function connect the external IR emitter and aim it at the specific AC unit The operating distance of external IR emitter is around 100cm High power mode and 50cm Low power mode but it is also depends on the sensitivity of the IR receiver External IR emitter cable Q Where I keep up to date with the latest Z Wave products for my house A You keep up to date by visiting the www remotec com hk website where we will have information and ideas for using Z Wave technology TECHNICAL SPECIFICATIONS BW8377EU ZXT 120EU Model n BW8377AU ZXT 120AU PR BW8377US ZXT 120US BW8377IN ZXT 120IN 868 4MHz EU ZXT 120EU RF frequenc 921 4MHz AU ZXT 120AU uer 908 4MHz US ZXT 120US 865 22MHz IN ZXT 120IN RF operating distance up to 80ft outdoor line of sight in unobstructed environment IR operating distance up to 25ft line of sight in unobstructed environment R learning IR 1 Max 20 commands Measurable range 32 104 F 0 40 Tempera
9. the amount of objects in between Z Wave devices such as walls and furniture Every Z Wave device set up in your network will act as a signal repeater allowing devices to talk to each other and find alternate routes in the case of a reception dead spot Radio frequency limitations 1 Each wall or object 1 refrigerator bookshelf large TV etc can reduce the maximum range of 65 feet by up to 25 to 30 2 Plasterboard and wooden walls block less of the radio signal then concrete brick or tile walls which will have more of an effect on signal strength 3 Wall mounted Z Wave devices will also suffer a loss of range if they are housed in metal junction boxes which could also reduce the range by up to 25 to 30 MAINTENANCE I Do not expose your ZXT 120 to dust strong sunlight humidity high temperatures or mechanical shocks 2 Do not use old and new batteries together as old batteries tend to leak Do not use corrosive or abrasive cleansers on your ZXT 120 Keep the unit dust free by wiping it with a soft dry cloth 5 not disassemble your ZXT 120 it contains no user serviceable parts A FREQUENTLY ASKED QUESTIONS Z Wave Frequently Asked Questions Why won t my ZXT 120 work with the Z Wave devices I purchased from another country Due to different countries regulations Z Wave products from different regions are set to different frequencies Before purchasing new devices make sure you have checked that the de
10. and Parameter Value of configuration command Parameter Definitions P Number arameter Value 25 Indicate a location for IR 1 20 0x19 code learning and start 0x00 0x14 learning 26 Learning status register 0x00 Idle this IR Ox1A channel is idle default Note 0x01 OK the latest The status value 0x01 and learning process 0x04 will be reset to 0 successful and when the ZXT 120 receive completed a get command to this parameter 0x02 Learning the ZXT 120 is busy processing previous learning request 0x04 Failed the latest learning request failed 27 IR code number for built Refer Code list for 0x1B in code library details 28 External IR Emitter power 0x00 normal power Ox1C level mode OxFF high power mode default 32 Surround IR control 0x00 disable 0x20 to avoid the IR Surround IR Emitters interference by disabling 9XFF enable the surrounding IR Surround IR Emitters emitter if 2 air default conditioners in a room are used extend the battery life by disabling the Surround IR Emitters Indicate a location for 1 20 transmitting a learnt IR 0x00 0x14 code Parameter Table Mapping Information BASIC Set Value 0x00 will map to Thermostat mode Off 0x00 BASIC set Value OxFF will map to Thermostat mode Resume 0x05 Listening Mode default mode is FLiRS ZXT 120 can be configured as either Frequently Listening Routing Slaves FLIRS or Always L
11. er ZXT 120 Operations Before using the ZXT 120 please read the INSTALLATION if it is needed to mount the ZXT 120 to a wall Power up the ZXT 120 by the USB Power 5Vdc or Dry battery AAA x 3pcs e Plug in 5Vdc power into the USB socket if operated at Always Listening mode Or e Install 3x AAA batteries if operated at FLiRS mode e Please refer to the section of MOUNTING PROCEDURE e Remove the battery cover on the back of your ZXT 120 battery chassis e Mount the battery cover into the main unit with 2 screws e Check the polarity of the batteries and the marks inside the battery compartment Insert the batteries e Push the battery cover and main unit back in place CAUTION battery and power adaptor safety Use new batteries of the recommended type and size only Never mix used and new batteries together To avoid chemical leaks remove batteries from the ZXT 120 if you do not intend to use the remote for an extended period of time Dispose of used batteries properly do not burn or bury them Please carefully read through the following then store the manual for future reference Product Overview Temperature sensor PROG Button Learning and LED Indication Battery chassis USB Power 5V DC External IR Port Surround IR Output for top and 4 directions Figure 2 PROG Key and IR Port of ZXT 120 Z Wave Remote Control 1 2 3 4
12. istening node after exclusion process FLiRS node type is targeted for battery operated applications and it will enter sleep mode frequently in order to conserve battery consumption Always Listening node type is targeted for the needs of required a fast response application Important It is not allow changing ZXT 120 operation mode without the step of exclusion process How to switch ZXT 120 listening mode from Always Listening to FLiRS vice verse Setup Re LED Indication Status on ZXT 120 Press and hold the PROG e LED stay off button on the ZXT 120 for around 4 seconds Release the button and e LED flashes twice then press the PROG then stay off button 3 times within 3 ZXT 120 set in seconds FLiRS mode OR e LED flashes four times then stay off ZXT 120 set in Always Listening mode IR Code Learning User can follow the gateway UI to implement the learning function the learnt IR code will be stored in a specify control key which contains the Mode Temperature and Fan Speed information Learning example for Key_1 Mode COOL Temperature 20 C Fan Speed HIGH How to learn an IR code on ZXT 120 Setup LED Indication a Status on ZXT 120 Configuration command e LED flashes once class with following parameter number and value are received Parameter number 25 Parameter value 1 20 Place the ZXT 120 and your device remote as shown below
13. lers Like every Z Wave accessory user will need to include the ZXT 120 into their Z Wave network using the primary controller Then the user can use either the primary controller or secondary controller to configure and setup the ZXT 120 using Z Wave s configuration command class Once the configuration and setup is complete the controller can use Z Wave s Thermostat commands class to control their IR controlled air conditioner with the ZXT 120 Controller and Gateway Requirements The ZXT 120 is architected to work with any Z Wave compliant controller or gateway supporting the following Z Wave commands Configuration Command Class Multilevel Sensor Command Class Sensor Configuration Command Class Thermostat Command Class Thermostat Mode Command Class Thermostat Fan Mode Command Class Thermostat Set point Command Class Built in IR code library The built in IR code library enables the ZXT 120 to work with any Z Wave compliant gateway and controller Gateway and controller will not need to have any knowledge related to IR control code It also eliminates the needs of complicated set up procedures and proprietary Z Wave commands to configure the system The IR code library supports various brand name air conditioners found in the today s market User can use his controller or gateway to send a 3 digits AC IR code number include the brand selection using standard Z Wave configuration command Gl
14. ossary Devices and nodes are all terms to describe Device or Node an individual Z Wave device These all interchangeable when setting up your Z Wave network Add a Z Wave device to the network Delete a Z Wave device from the network To take a device out of a group scene or Remove association group while that device still exists in the same Z Wave network A collection of Z Wave devices is controlled by primary and secondary controllers Z Wave operating on the same system A Z Wave Network network has its own unique ID code so that controllers not in the network cannot control the system The first controller is used to set up your devices and network Only the Primary Primary Controller can be used to include or delete Controller devices from a network It is recommended that you mark the primary controller for each network for ease in modifying your network A controller containing network information about other devices within the network and is Secondary used for controlling devices Secondary Controller controller is created from the Primary Controller and cannot include or delete devices to the network A controller containing network information about other devices within the network and is used for controlling devices Inclusion controller is created from the Primary Controller in a SIS enabled Z Wave network Inclusion Controllers have the ability to add and remove devices from the network Inclusion Controll
15. outlet shall be installed near the equipment and shall be easily accessible Use only power supplies listed in the user instructions Do not dispose of electrical appliances as unsorted municipal waste use separate collection facilities Contact your local government for information regarding the collection systems available CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS www remotec com hk Printed in China F820 8377 0000
16. posed to smoke or steam Doing so could cause a fire or electrical shock Do not mount in locations with high humidity or large amounts of dust Doing so could cause a fire or electrical shock Do not mount to locations subject to high temperatures high humidity or exposure to water Doing so could cause a fire or electrical shock Do not mount to locations subject to large amounts of vibration large jolts or large forces These could cause an injury if the ZXT 120 falls and breaks MOUNTING PROCEDURE PRECAUTIONS Do not modify parts or use the ZXT 120 in ways other than its intended use Doing so could cause the ZXT 120 to fall and result in an injury Be sure to fully check that there are no electrical wires or pipes inside the wall before mounting If any of the screws are loose the ZXT 120 can fall and cause an injury Do not mount the ZXT 120 with the screws still loose Check that the two screws mounted to the wall are fully inserted into the key holes of the ZXT 120 Otherwise the ZXT 120 can fall and cause an injury Do not mount the ZXT 120 so that it sticks out from the wall edge It could get hit by people s bodies or objects and cause an injury Supplier will not be liable for any accidents or injuries that occur due to improper mounting or handling When mounting be careful not to get your fingers pinched or injure your hands MOUNTING PROCEDURE The ZXT 120 can be mounted to a wall or wooden racks using the two
17. ture Operation 0 40 C Storage 20 60 C Dry battery AAA x 3pcs Dia 70mm 18mm Main unit Dia 70mm T 15 5mm Battery chassis 35g Battery chassis excluded Weight 60g Battery chassis included 90g Main Battery chassis AAA x3pcs Z Wave device type Basic Device Class BASIC_TYPE_ROUTING_SLAVE Generic Device Class GENERIC_TYPE_THERMOSTAT Specific Device Class SPECIFIC_TYPE_THERMOSTAT_GENERAL_V2 Z Wave Command Class Version Controlled Supported COMMAND_CLASS_THERMOSTAT_MODE co COMMAND CLASS VERSION Versionl Supported function in Thermostat Command Class Thermostat Fan mode Thermostat Mode Auto Changeover N Energy Save Heat N ZXT 120 functions and Parameters summaries AIR Z WAVE COMMAND FUNCTIONS CONDITIONER Z WAVE COMMAND CLASS COMMAND PARAMETER FUNCTION COMMAND CLASS THERMOSTAT THERMOSTAT _ MODE 5 _MODE MODE_SET POWER ON COMMAND CLASS BASIC BASIC SET VALUE OXFF POWER COMMAND CLASS THERMOSTAT THERMOSTAT _ MODE 0 MODE MODE SET POWER OFF COMMAND CLASS BASIC BASIC SET VALUE 0X00 COMMAND CLASS THERMOSTAT THERMOSTAT _ MODE MODE SET COMMAND CLASS THERMOSTAT THERMOSTAT _ MODE MODE SET COMMAND CLASS THERMOSTAT THERMOSTAT _ MODE MODE SET MODE 3 MODE 2 MODE 6 COMMAND CLASS THERMOSTAT THERMOSTAT MODE 1 MODE 8 SET _MODE MODE_SET COMMAND CLASS THERMOSTAT THERMOSTAT_ _MODE MODE_SET
18. vice is compatible in your region Q How do I know which product is compatible with my ZXT 120 ZXT 120 should work with any Z Wave controller or gateway that has control capability for Thermostat devices You can check either the specifications in the manual of your ZXT 120 or also check online at www remotec com hk for a full list of products that can be used with your ZXT 120 All Z Wave products also come with the Z Wave logo gt Can use the USB port to configure ZXT 120 No the mini USB port only provides an alternative option for user to power the ZXT 120 Do I need an electrician to install Z Wave products in my house Installation can be simple In some cases all you need to do is mount the ZXT 120 to a wall or wooden racks You also can place the ZXT 120 on the desk and power it with dry cell batteries How to select my air conditioner IR code from ZXT 120 You should refer to the code list and look into the brand and try the code no sequentially until you find the right code You can record down your device code under the table for future reference after setting up the ZXT 120 correctly ZXT 120 is working on top and 4 directions IR output but there is no response on the IR emitter socket why ZXT 120 supports two IR power levels for the external IR emitter to avoid saturation of the IR receiver You can set the IR output power level by the Parameter Table value normal or
Download Pdf Manuals
Related Search