IFS POE302-EX User Manual - Utcfssecurityproductspages.eu
Contents
1. Interlogix 2 6 United Technologies 7 IFS POE302 EX User Manual P N 1072690 REV A 155 230CT13 Copyright Trademarks and patents Manufacturer Intended use Certification FCC compliance ACMA compliance Canada European Union directives Contact Information O 2013 United Technologies Corporation Interlogix is part of UTC Climate Controls amp Security a unit of United Technologies Corporation All rights reserved The IFS POE302 EX name and logo are trademarks of United Technologies Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products Interlogix 3211 Progress Drive Lincolnton NC 28092 USA Authorized EU manufacturing representative UTC Climate Controls amp Security B V Kelvinstraat 7 6003 DH Weert Netherlands Use this product only for the purpose it was designed for refer to the data sheet and user documentation for details For the latest product information contact your local supplier or visit us online at www interlogix com C G This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not i2. 5 up to 100m 328ft Network Cable 1000Base T 4 Pair UTP Cat 5e 6 up to 100m 3288 EIA TIA 568 100 ohm STP 100m 328ft Standards Conformance Regulation Compliance FCC Part 15 Class A CE IEEE 802 3 10Base T Ethernet IEEE 802 3u 100Base TX Fast Ethernet IEEE 802 3ab 1000Base T Gigabit Ethernet IEEE 802 3af Power over Ethernet IEEE 802 3at Power over Ethernet Pre standard IEEE 802 3x Flow Control Standard Compliance IFS POE302 EX User Manual Environment Temperature 10 60 Degree C Relative Humidity 5 9596 non condensing Operating Temperature 40 85 Degree C Storage Relative Humidity 5 95 non condensing Distance will often be shorter due to power delivery voltage drop on the wire The maximum distances will vary on the quality of the UTP cable and environment IFS POE302 EX User Manual Hardware Description 2 1 Product Outlook e e POE302 EX Gigabit Ethernet PoE AT Extender S ife 2 1 952 80001 001 01 IFS POE302 EX User Manual 2 2 Ports Connection Connect the PoE IN port from following 802 3at 802 3af PSE device through a CAT 5 5e 6 UTP cable e PoE injector IN Port PoE Injector Hub e PoE Ethernet Switch e Previous POE302 EX Connect the PoE OUT port to following 802 3at 802 3af PD device through a CAT 5 5e 6 UTP cable PoE IP Camera OUT Port e PoE VoIP Phone e PoE Wireless AP e PoE S
3. connection 11 IFS POE302 EX User Manual 3 5 Optional DIN Rail Mounting There are two DIN Rail holes on the left side of the POE302 EX that allows the converter can be easily installed with DIN Rail mounting The IFS optional DIN Rail mounting Kit RKE DIN can be order separately When need to replace the wall mount application with DIN Rail application on the POE302 EX please refer to following figures to screw the DIN Rail on the converter To hang the POE302 EX follow the below steps Step 1 screw the DIN Rail on the POE302 EX 12 IFS POE302 EX User Manual Step 3 Check the DIN Rail is tightly on the track You must use the screws supplied with the mounting brackets Damage caused to the parts by using incorrect screws would invalidate your warranty 13 IFS POE302 EX User Manual Contacting Technical Support Contact technical support if you encounter any difficulties during this installation Please make sure you have the requested diagnostic or log files ready before you contact us by phone or go to www interlogix com customer support Technical Support Europe Middle East and Africa W Select Contact Us at www utcfssecurityproducts eu North America T 1 855 286 8889 E techsupportQinterlogix com Australia E techsupport interlogix au
4. he remote Powered Device PD to the OUT port of POE302 EX Step 4 The OUT port is also the power injectors which transmit DC Voltage to the Cat 5 5e 6 cable and transfer data and power simultaneously between the PSE and PD Step 5 Once POE302 EX detects the existence of an IEEE 802 3at 802 3af device the PoE OUT LED indicator will be steady ON to shows it is providing power Power POE302 EX Data Power Data Power 100 meters 100 meters PoE IP Camera 802 3at 802 3at PoE Extender PoE Injector g F 200 meters 5 Power Line AC Power Line DC 1000Base T UTP 1000Base T UTP with PoE If the connected device is not fully complying with IEEE 802 3at 802 3af standard or in line power device the PoE OUT LED indicator of POE302 EX will not be steady on According to IEEE 802 3at 802 3af standard the POE302 EX will not inject power to the cable if not connecting to a standard IEEE 802 3at 802 3af device 3 4 Multiple PoE Extender Installation The POE302 EX PoE Extender supports multiple units daisy chain installation They can be employed in series for even longer distances based on remote PoE IP Camera or PoE Wireless Access Point power requirement Step 1 Connect the additional Cat 5 5e 6 cable from the OUT port of the first POE302 EX the other end of the UTP cable be used to connect to the IN port of remote nex
5. nne aa E A aE a E E 8 HARDWARE INSTALLATION 9 3 1BEIOE INS LANA OR ee 9 3 2 Connect POE302 EX to the Power Source Equipment PSE 9 3 3 Connect POE302 EX to the Powered Device PD 10 CONTACTING TECHNICAL SUPPORT 14 IFS POE302 EX User Manual Introduction 1 1 Package Contents Thank you for purchasing the IFS POE302 EX IEEE 802 3at Power over Gigabit Ethernet Extender your Power over Gigabit Ethernet Extender package contains the following contents Check the contents of your package for following parts B IEEE 802 3at Power over Gigabit Ethernet Extender x1 B User s Manual x1 If any of these pieces are missing or damaged please contact your dealer immediately if possible retain the carton including the original packing material and use them against to repack the product in case there is a need to return it to us for repair 1 2 Key Features B IEEE 802 3at 802 3af Power over Ethernet compliant B Complies with IEEE 802 3 802 3u 802 3ab 10 100 1000Base T B Extends the range of PoE an additional 100 meters 328ft B Auto detect and protect of PoE equipment from being damaged by incorrect installation B Multiple units daisy chain installation s
6. nstalled and used in accordance with the instruction manual may cause harmful interference to radio communications You are cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Notice This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe est conforme la norme NMB 003du Canada 2004 108 EC EMC Directive Hereby UTC Climate Controls amp Security Corporation Inc declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2004 108 EC For contact information see www interlogix com or www utcfssecurityproducts eu IFS POE302 EX User Manual TABLE OF CONTENTS IFS POE302 EX USER MANUAL uuu uu died 1 INTRODUC HON pee 4 T l Package Contents PIC Vas sac brendan Deo T Da Qa na ead 4 1 2 ee 4 1 8 u u ae 5 HARDWARE DESCRIPTION 7 21 Product OUT OOK sa 7 2 2 Ports CONNCCUOM y u u u u u MID DE M EE ce EE 8 23 LED Defio raiso
7. plitter e Next POE302 EX 2 3 LED Definition LED Lights to indicate the port is providing 52 56V 802 3at 48V 802 3af DC in line power LNK ACT Lights to indicate the port is link up Blink indicate that the extender is actively sending or receiving data over IN port PoE OUT Lights to indicate the port is providing 52 56V 802 3at 48V 802 3af DC in line power IFS POE302 EX User Manual Hardware Installation This product provides three different running speeds 10Mbps 100Mbps and 1000Mbps in the same device and automatically distinguishes the speed of incoming connection This section describes the hardware features of POE302 EX Before connecting any network device to the POE302 EX read this chapter carefully 3 1 Before Installation Before your installation it is recommended to check your network environment If there is any far away IEEE 802 3at 802 3af devices need to power on the POE302 EX can provide you a way to supply power for this Ethernet device conveniently and easily The POE302 EX is installed between the PSE Power Source Equipment and the PD Powered Device it is powered by PSE and forwards the Ethernet data and remaining POE power to the PD The POE302 EX doesn t require an external power supply and it can be installed easily just plug and play that means the operator does not need to configure the POE302 EX The POE302 EX injects power to the PDs without affecting the data t
8. ransmission performance It offers a cost effective and quick solution to extend power and data an additional 100m 1 To provide you better PoE power and data extension quality we strongly recommend that you use Solid UTP Cable when installing POE302 EX 2 The POE302 EX can be installed with third party device if the device complied with IEEE 802 3at 802 3af standard 3 2 Connect POE302 EX to the Power Source Equipment PSE There are 2 RJ 45 ports in the PoE Extender of which the IN port functions as PoE Data and Power input and the OUT port on the other side functions as PoE Data and Power output Step 1 Connect a standard Cat 5 5e 6 UTP cable from Power Source Equipment PSE such as PoE Switch PoE Injector hub and single port PoE injector to the IN port of POE302 EX Step 2 The PSE delivers both Ethernet Data and PoE power over UTP cable to the POE302 EX and the PoE IN LED will be steady on The POE IN LED turn on steady green means POE302 EX is being powered successfully with PoE class O If POE IN LED does not turn on please check the remote PSE or the cable with a PC or a network device to see if the cable is correct Or with an IEEE 802 3at 802 3af device such as the target PD to check the power injection is correct either IFS POE302 EX User Manual 3 3 Connect POE302 EX to the Powered Device PD Step 3 Connect the additional Cat 5 5e 6 cable that will be used to connect to t
9. t POE302 EX Step 2 The OUT LED indicator of the first POE302 EX will be steady to shows it is providing power to next PoE Extender Step 3 The PoE IN LED on the next POE302 EX will steady Step 4 Connect the additional Cat 5 5e 6 cable to the remote PoE powered device to the OUT port of next or third POE302 EX 10 IFS POE302 EX User Manual 400m J00m 200m 100m Om Distance TOW 201 24M 30WW PoE IP Camera 802 802 802 Jat PoE Extender PoE Extender PaE Extender POE302 EX 100M 100M 100M 85 OG E i o 2 s Outdoor IR 802 3at B02 3at 802 3at PoE Ethernet IP Camera PoE Extender PoE Extender Switch Injector Hub POE302 EX 802 NET B PoE Splitter Power Line AC i Power Line DC i p 10006 UTP k i 802 3at 10008ase T UTP with PoE j PoE Extender 02 Camera 1 Per POE302 EX will take 3 2 Watts maximum for the system itself please check the total power consumption of your IEEE 802 3at 802 3af PD and the POE302 EX before you make the daisy chain connection If the overall power consumption is overloaded the local PSE could shutdown the whole power system Per POE302 EX cable segment is limited in 100 meters Cat 5 5e 6 UTP wire from its IN OUT port to the other data end use of any other non standard cable or over distance could results in unstable
10. upport B Forwards both Ethernet data and PoE power to remote device B No external power cable installation required B Compact size Wall mountable design B Plug and Play installation IFS POE302 EX User Manual 1 3 Technical Specification Interfaces 1 x 10 100 1000Base T Ethernet with IEEE 802 3at 802 3af PoE LANIN Data DC in Auto MDI MDI X Auto negotiation RJ 45 connector 1 x 10 100 1000Base T Ethernet with IEEE 802 3at 802 3af PoE LAN OUT Data DC out Auto MDI MDI X Auto negotiation RJ 45 connector Power over Ethernet IEEE 802 3af Power over Ethernet oE plendere IEEE 802 3at High Power over Ethernet Pre Standard PoE Power Supply Type Mid Span PoE Power Output 52V DC 510mA Max 26 Watts Power Pin Assignment 4 5 7 8 Maximum Distance 3 units daisy chain installation with 500m support Hardware Specification Data Rate 10 100 1000Mbps Switch Architecture Store and Forward 10Mbps 14880pps 64Bytes Switch Throughput 100Mbps 148810pps 64Bytes 1000Mbps 1488000pps 64Bytes 1552Bytes Flow Control Back pressure for Half Duplex IEEE 802 3x Pause Frame for Full Duplex 1x PoE IN Green LED Indicators e 1xLAN Data Green e 1x PoE OUT Green p ESD Ethernet 2KV TBD otectio Surge EFT for power 2KV TBD Dimension W x D x H 94 x 70 x 26 mm Meshal oils OR 10Base T 4 Pair UTP Cat 5 up to 100m 328ft 100Base TX 4 Pair UTP Cat
Download Pdf Manuals
Related Search