FP0 CC-Link Slave Unit - Panasonic Electric Works
Contents
1. iN u Can be used in accuracy as shown above an be used in the standard specifications Reference lt FPO Thermocouple Unit Technical Manual ARCT1F366E gt 2 Part Names and Functions 2 1 Part Names and Functions FP gt CC Link slave unit FPG CCLS AFPG7943 X w TS e DOperating monitor LEDs Number of occupied stations Available only for FP X CC Link slave unit Station No selector switch Baud rate selection switch GTransmission line RS485 terminal block Fixing screw for a detachable terminal block DExpansion connector occupied station No selection switch Available only for FP gt CC Link slave unit Expansion connector Available only for FP gt CC Link slave unit Power supply connector 24V DC DExpansion connector Available only for FPO CC Link slave unit DOperating monitor LEDs RUN Turns when communication is normal ERR Turns ON when a switch setting error has occurred Flashes when a switch setting is changed while the power is ON SD Turns ON when data is being transmitted RD Turns ON when data is being received ALARM Turns ON when a hardware error has occurred Turns ON when a station No setting error has occurred Number of occupied stations Available only for FP gt CC Link slave unit 1 to 4 LEDs Number2. Cause of the ES FP0 2 gt control unit Woon oe bane ad Grate ERRATARM zm ud status occupied number of stations etc Station No setting Flashing OFF Normal Operation is not affected change Error flag can be checked in the master station Baud rate setting Flashing OFF Normal Operation is not affected change Error flag can be checked in the master station Station No setting ON ON Normal Operation cannot be executed error Baud rate setting ON ON Normal Operation cannot be executed error Setting change of OFF ON I O verification error Operation cannot be executed occupied number of stations Hardware error ON Extra unit out of control Operation cannot be executed Note 1 Extra unit out of control cannot be detected in the FPO CC Link slave unit When a hardware error occurs in the FPO CC Link slave unit I O verification error is issued Note 2 As one occupied station is used for FPO CC Link slave unit FPO CC Link slave unit has no LEDs indicating the number of occupied stations Therefore the setting change error of occupied number of stations is not issued 6 Specifications 6 1 Specifications General specifications Item Description Rated voltage 24V DC Operating voltage range 21 6 to 26 4V DC Rated current consumption CC Link unit 40 mA or less 24V DC Increase amount in the control unit when expansion units are added 40 mA or less 2
3. Switch setting status Installation status Flashing of ERR LED in the master station Master side Remote input RX from the CC Link slave unit cannot be received Check Output Y on the CC Link slave unit side Does the CC Link slave unit participate in the data link Check the followings LED indication in the CC Link slave unit Communication status in other stations of the master station Is the data read from the correct address of the master station remote input RX Check the sequence program in the master station Is the data written in the correct number allocated to the CC Link slave unit Check the sequence program in the FP0 FP gt control unit Is the station specified as reserved one Check the contents of the parameters in the master station Does the station No overlap Check the station No Do the connection and setting comply with the specifications for the master station Check the specifications for the master station Master side Remote output RY from the CC Link slave unit cannot be turned ON OFF Check Input X on the CC Link slave unit side Does the CC Link slave unit participate in the data link Check the followings LED indication in the CC Link slave unit Communication status in other stations of the master station Is the refresh instruction output turned ON in the master station Check the sequence program in th
4. 16 X150 X15F X230 X23F X310 X31F X390 X39F RY50 RY5F ae 112 X100 X16F X180 X24F X260 X32F X340 X40F RYOO RY6F 4 PM 16 X170 X17F X250 X25F X330 X33F X410 X41F RY70 RY7F Note 1 The expansion units closer to the control unit have the lower expansion unit number Expansion unit 1 2 3 and 4 Note 2 Remote I O RX and RY are the descriptions for the master station from MITSUBISHI System area allocation bit Master station FP X CC Link e Signal RX 0 A Y 0 A Not available RX B Y B Remote station Ready RX C F Y C F Not available RY 0 F Not available Note The value marked with position of the unit For details refer to the allocation tables above varies depending on the installation Note System areas cannot be used in the user program 3 1 2 Shared Memory Allocation Slot No y uoisuedx3 uoisuedx3 Z uoisuedx3 yun uoisuedx3 FP X expansion unit No 1 2 3 4 Shared memory slot No 0 1 2 3 diagram on the left Error information and status All the data cannot be updated Note The expansion units closer to the control unit have the lower expansion unit number Expansion unit 1 2 3 and 4 in the Shared memory address word unit Item Description decimal number 00 to 16 System reserved area N
5. of occupied stations turns ON Station No selector switch Upper digit x10 STATION I No N Lower digit x1 Baud rate selection switch 1 to 64 Station No 0 and 65 to 99 Setting error er 625k ES F 5M 10M 1 OFF ON OFF ON OFF 2 OFF OFF ON ON OFF 3 OFF OFF OFF OFF ON OFF Input data is cleared when communication halts Norg ON Input data is held when communication halts Mele Note FP0 FP gt input data output data from the master station Transmission line RS485 terminal block CC Link unit Used for connecting the CC Link cables The terminals SLD and FG are connected each other inside the Fixing screw for a detachable terminal block DExpansion connector occupied station No selection switch Available only for FP gt CC Link slave unit Expansion connector SW No Number of occupies station 108 1station 2 stations 3 stations 4 stations 1 ON OFF ON OFF OFF Left 2 ON ON OFF OFF S Note These switch settings are available only for FP gt CC Link slave unit Expansion connector Available only for FP X CC Link slave unit Power supply connector 24V DC Supply 24V DC power Use the provided power supply cable for connection Power used for the transmission line drive FG terminals of the power supply connector and transmission line terminal block are not connected in the CC L
6. provided as an accessory of the unit between the terminals DA and DB in the units at both ends For details refer to the CC Link master station s manual Connection Dedicated CC Link cable Dedicated CC Link cable The shielded CC link cable should go through the terminals SLD and FG in each unit and both ends should be grounded less than 100 The terminals SLD and FG are connected each other inside the unit When CC Link slave unit is used as the terminal station Secure the cable and terminal resistor to the terminal block using the screws Terminal resistor ES When CC Link slave unit is not used as the terminal station Secure the cables to the terminal block using the screws 5 Error Occurs 9 1 Troubleshooting Error Item Confirmation Entire system data link error Are any cables broken Check the cable status visually or by the line test Are terminal resistors properly connected to the stations at the both ends Connect terminal resistors provided for the master station to the stations at the both ends Has an error occurred in the control unit of the master unit Check the error code for the master station and take the proper measure Are parameters set for the master station Check the contents of the parameters Has an error occurred in the master station Check the followings Parameter status in the host station
7. the terminal while turning on electricity It could lead to an electric shock Use the external devices to function the emergency stop and interlock circuit Connect the wires or connectors securely The loose connection could cause excessive exothermic heat or smoke generation Do not allow foreign matters such as liquid flammable materials metals to go into the inside of the product It could cause excessive exothermic heat or smoke generation Do not undertake construction such as connection and disconnection while the power supply is on It could lead to an electric shock Copyright Trademarks This manual and its contents are copyrighted You may not copy this manual in whole or part without written consent of Panasonic Industrial Devices SUNX Co Ltd Windows is a registered trademark of Microsoft Corporation in the United States and other countries All other company names and product names are trademarks or registered trademarks of their respective owners PLC ORG Table of Contents Precautions before Using CC link Slave Unit 1 Functions of CC Link Slave Unit 1 1 1 nit F nctlons ineen id 1 o E D ME 1 Tid Unit Connection aaa 2 2 Part Names and Functions uuu iic luu een odeveasanccecdesoccesdyecadcedcacesTeteanscededesaenctunes 3 2 1 Part N mes and E rictiolis nete ene t
8. 4V DC Allowed momentary power off time 10 ms Ambient temperature 0 to 55 C Storage temperature 20 to 70 C Ambient humidity 30 to 85 RH at 25 C non condensing Storage humidity 30 to 85 RH at 25 C non condensing Breakdown voltage Between RS 485 e Power supply terminal terminals Station No 500V AC for 1 min Insulation resistance Between RS 485 lt gt Power supply terminal 100 M9 or more terminals Station No measured with 500V DC Vibration resistance 10 to 55 Hz 1cycle 1min double amplitude of 0 75 mm on 3 axes for 10 min Shock resistance Shock of 98 m s or more 4 times on 3 axes Noise immunity 1000 Vp p with pulse widths 50 ns and 1 based on in house measurement Operating condition Free from corrosive gases and excessive dust FP X CC Link slave unit Approx 90 g aan FPO CC Link slave unit Approx 80 g CC Link communication specifications Item Description Version CC Link Ver 1 10 Communication method Broadcast polling method Communication speed 10Mbit s 5Mbit s 2 5Mbit s 625kbit s 156kbit s Baud rate Ver 1 10 CC Link cable CC Link high performace CC Link cable cable 10Mbit s 100m 100m Maximum 5Mbit s 160m 150m total cable 2 5Mbit s 400m 200m Note 625kbit s 900m 600m 1 56kbit s 1200m 1200m Interface RS485 length Station type Rem
9. C Link Slave Unit Communication with FP0 control unit Only one FP0 CC Link slave unit can be installed on the extreme right in the expansion unit s In the FP0 CC Link slave unit CC Link remote I O and remote register are allocated to the expansion unit I O 1 word and 2 word or later respectively The number of the word of the remote register varies depending on the expansion unit s installation position Number of remote I O points 16 input points 16 output points Remote register Max 4 words for read and write each A Reference 3 2 1Expansion unit I O allocation FER i When 5 words can be used d Remote I O 1 word input 1 word output Remote register 4 words read 4 words write When 4 words can be used Remote l O 1 word input 1 word output Remote register 3 words read 3 words write When 2 words can be used Remote l O 1 word input 1 word output Remote register 1 word read 1 word write o gt 3 o x o 3 2 5 5 3 FPO CC Link Master station slave unit Remote input Y RX 1st word Remote 1 0 Remote output X RY 1st word 1 0 Remote register RWr 2nd word or later Remote device Remote register RWw 2nd word or later Note In the FP0 CC Link slave unit shared memory cannot be used When an expansion unit is newly added after the I O allocation is set the I O allocation is conc
10. C Link slave unit are allocated to the I O area Reference lt 3 Allocation of Input Output and Shared Memory gt 1 3 Unit Connection Limitations in unit number and position FP gt CC Link slave unit Up to 4 expansion units including other FP X expansion unit and FP X high performance unit can be installed FP0 CC Link slave unit Up to 3 expansion units including other FP0 expansion unit and FP0 high performance unit can be installed However two or more FP0 CC Link slave units cannot be installed in a system A unit cannot be installed on the right of the FP0 CC Link slave unit because the unit does not have the expansion connector on its rihgt When using the CC Link slave unit with the FP0 thermocouple unit In the FP0 thermocouple unit manual it is not recommended for any unit to be installed on the right side of the FPO thermocouple unit to assure the measurement accuracy However the FPO CC Link slave unit can be installed on the right of the FPO thermocouple unit In this case the accuracy for the FPO thermocouple unit is as shown in the table below Standard When CC Link Thermocouple used specifications slave unit with the thermocouple unit K J T 0 8 C 2 C 0 to 99 9 C 3 C 6 C R 100 to 299 9 C 2 5 C 5 C 300 to 1500 C 2 C 4 C 00006566 B Thermocouple unit Thermocouple unit
11. Panasonic PROGRAMMABLE CONTROLLER FP2 CC Link Slave Unit FPO CC Link Slave Unit Technical Manual ARCT1F380E 4 2013 7 panasonic net id pidsx global Safety Precautions Observe the following notices to ensure personal safety or to prevent accidents To ensure that you use this product correctly read this User s Manual thoroughly before use Make sure that you fully understand the product and information on safety This manual uses two safety flags to indicate different levels of danger WARNING If critical situations that could lead to user s death or serious injury is assumed by mishandling of the product Always take precautions to ensure the overall safety of your system so that the whole system remains safe in the event of failure of this product or other external factor Do not use this product in areas with inflammable gas It could lead to an explosion Exposing this product to excessive heat or open flames could cause damage to the lithium battery or other electronic parts CAUTION If critical situations that could lead to user s injury or only property damage is assumed by mishandling of the product To prevent excessive exothermic heat or smoke generation use this product at the values less than the maximum of the characteristics and performance that are assured in these specifications Do not dismantle or remodel the product It could cause excessive exothermic heat or smoke generation Do not touch
12. ax 81 52 936 6005 E mail cc link postO mind ne jp HP English http Avww cc link org eng index html Japanese http www cc link org 1 Functions of CC Link Slave Unit 1 1 Unit Functions 1 Data can be exchanged between the CC Link master station and 2 slave station 2 Communication speed 157k to 10Mbit s 3 Communication distance 100 m to 1200m 4 Interface RS485 5 1 O points 161 160 to 801 800 FPO CC Link slave unit 161 160 to 1121 1120 FP X CC Link slave unit 1 2 Unit Type CC Link slave unit Number of data points exchanged with CC Link Product No master station 256 points Max 224 points Max Note1 Name Type points aja vami FPG CCLS Input 128 Input 112 Output 112 AFPG7943 Output 128 16 word data read write Max FPO 192 points Max 32 points Max CC Link slave unit FPO CCLS Input 96 Input 16 Output 16 07943 Output 96 4 word data read write Max Note 1 Occupied number of I O points in the FP 2 0 expansion area The number of the occupied I O points varies depending on the switch setting for FP gt CC Link slave unit and the location of the expansion unit for FPO CC Link slave unit Note 2 FPO CC Link slave unit does not have a connector for the next expansion unit One FPO CC Link slave unit should be installed on the extremely right in the expansion position Note 3 All the data for the FPO C
13. e master station Is the data written in the correct address of the master station remote output RY Check the sequence program in the master station Is the data read from the correct number allocated to the CC Link slave unit Check the sequence program in the FPO FP gt control unit Is the station specified as reserved one Check the contents of the parameters in the master station Does the station No overlap Check the station No Do the connection and setting comply with the specifications for the master station Check the specifications for the master station Master side Remote register RWr data from the CC Link slave unit cannot be received Check Output Y on FPO CC Link slave unit side Shared memory address Nos 48 to 63 on FP gt CC Link slave unit side Does the CC Link slave unit participate in the data link Check the followings LED indication in the CC Link slave unit Communication status in other stations of the master station Is the data read from the correct address of the master station remote register RWr Check the sequence program in the master station Is the data written in the correct I O number FPO CC Link slave unit and shared memory address FP gt CC Link slave unit allocated to the CC Link slave unit Check the sequence program in the FP0 FP X control unit Is the station specified as reserved one Check the c
14. ink unit Isolated from the power for the control unit Expansion connector Available only for CC Link slave unit 3 Allocation of Input Output and Shared Memory 3 1 FP gt CC Link Slave Unit Communication with FP 2 control unit In the CC Link slave unit CC Link remote input output is allocated to the I O area and CC Link remote register is allocated to the shared memory area The number of remote words varies depending on the CC Link station No settings 1 to 4 stations Additionally I O allocation and shared memory slot No depend on the location to be installed Remote input output points per station input 32 points output 32 points Remote register per station 4 words for read 4 words for write A Reference 3 1 1Expansion Unit Allocation Remote input output Automatic update by the refresh instruction Remote register Executed by the shared memory READ WRITE instructions F150 and F151 Slot No FP X expansion unit No 1 2 3 4 Shared memory slot No 0 1 2 3 Note The expansion units closer to the control unit have the lower expansion unit number Expansion unit 1 2 3 and 4 in the diagram on the left g uoisuedx3 2 yun uoisuedx3 wun uoisuedx3 p uoisuedx3 CC Link Master station slave unit Remote input RX Remote I O I O Remote output Output data RW Remote reg
15. ister Shared memory RW Input data 311 Expansion Unit I O Allocation Remote input FP gt side output No of FP X CC Link installation position CC Link occupied Area Points Expansion Expansion Expansion Expansion master stations unit 1 unit 2 unit 3 unit 4 remote I O rl 16 Y100 Y10F Y180 Y18F Y260 Y26F Y340 Y34F RX00 RXOF pos 16 Y110 Y11F Y190 Y19F Y270 Y27F Y350 Y35F RX10 RX1F pars 48 Y100 Y12F Y180 Y20F Y260 Y28F Y340 Y36F RX00 RX2F 2 ros 16 Y130 Y13F Y210 Y21F Y290 Y29F Y370 Y37F RX30 RX3F EC 80 Y100 Y14F Y180 Y22F Y260 Y30F Y340 Y38F RX00 RX4F 3 P 16 Y150 Y15F Y230 Y23F Y310 Y31F Y390 Y39F RX50 RX5F d 112 Y100 Y16F Y180 Y24F Y260 Y32F Y340 Y40F RX00 RX6F 4 a 16 Y170 Y17F Y250 Y25F Y330 Y33F Y410 Y41F RX70 RX7F Remote output FP side input No of FP gt CC Link installation position ee tink occupied Area Points 7 master Expansion Expansion Expansion Expansion remote I O stations unit 1 unit 2 unit 3 unit 4 Note 3 si 16 X100 X10F X180 X18F X260 X26F X340 X34F RYOO RYOF 1 16 X110 X11F X190 X19F X270 X27F X350 X35F RY10 RY1F nn 48 X100 X12F X180 X20F X260 X28F X340 X36F RYOO RY2F 2 16 X130 X13F X210 X21F X290 X29F X370 X37F RY30 RY3F aes 80 X100 X14F X180 X22F X260 X30F X340 X38F RY00 RY4F 3 aan
16. lable Available Available Available 34 RWw2 Available Available Available Available 35 RWw3 Available Available Available Available 36 RWw4 Available Available Available 37 RWw5 Available Available Available 38 RWw6 Available Available Available F150 39 RWw7 x Available Available Available Master FP gt 40 Input RWw8 Available Available 41 RWw9 Available Available 42 RWwA Available Available 43 RWwB Available Available 44 RWwC Available 45 RWwD Available 46 RWwE Available 47 RWwF Available 48 RWr0 Available Available Available Available 49 RWr1 Available Available Available Available 50 RWr2 Available Available Available Available 51 RWr3 Available Available Available Available 52 RWr4 Available Available Available 53 RWr5 EE Available Available Available 54 RWr6 PE Available Available Available F151 55 RWr7 EE Available Available Available Output Master FP X 56 RWr8 Available Available 57 RWr9 Available Available 58 RWrA Available Available 59 RWrB Available Available 60 RWIC Available 61 RWID Available 62 RWrE Available 63 RWrF ES Available Note Remote register RWw and RWr are the descriptions for the master station from MITSUBISHI 3 2 FP0 C
17. ontents of the parameters in the master station Does the station No overlap Check the station No Do the connection and setting comply with the specifications for the master station Check the specifications for the master station Master side Remote register RWw from the CC Link slave unit cannot be turned ON OFF Check Input X on FPO CC Link slave unit side Shared memory address Nos 32 to 47 on FP X CC Link slave unit side Does the CC Link slave unit participate in the data link Check the followings LED indication in the CC Link slave unit Communication status in other stations of the master station Is the data written in the correct address of the master station remote register RWw Check the sequence program in the master station Is the data read from the correct number CC Link slave unit and shared memory address FP X CC Link slave unit allocated to the CC Link slave unit Check the sequence program in the FPO FP X control unit Is the station specified as reserved one Check the contents of the parameters in the master station Does the station No overlap Check the station No Do the connection and setting comply with the specifications for the master station Check the specifications for the master station Note For details refer to the CC Link master station manual 5 2 ERR ALARM LED
18. ot available bitOto3 Station No x10 Station No x 10 0 to 9 bit4to7 Station No x10 Station No x 10 0 to 6 ETA Baudrate 0 156kbit s etting information Updated when L 62Skbit s communication is I 2 2 5Mbit s established bit 8 to B Baud rate 0104 3 5Mbit s 4 10Mbit s un NEN DNE a Occupied station No bit C F occupies station nod 0 to 3 0 1 station to 3 4 stations Station No switch 0 Normal Station No switch is changed bit4 change 84Emo when power is ON Error E m ation Baud rate switch 0 Normal Baud rate switch is changed bit 5 change 1 Error when power is ON bit 4 5 8 9 0 Normal Other bit 0 bit 8 error 1 Error 0 Normal bit 9 Overtime 1 Error 19 Reserved area Not available Master CPU 20 bit 0 Operation mode P ein Status information flag bit 0 1 Other bit 0 Master CPU status bit 1 flag 0 Normal i 1 Error 21 to 31 Setting information Not available Remote device Addresses are indicated in a decimal number FP gt shared memory address Master station remote Number of occupied station register Instruction Word address 1 0 Hexadecimal 2 3 4 32 RWw0 Available Available Available Available 33 RWw1 Avai
19. ote device station Number of 1 to 4 stations switch changeover slave unit Ed FP0 CC Link points 1 station slave unit Note 1 Length of the multi drop connected cables at both ends The cable length has restrictions in communication speed CC Link version and dedicated cables to be used Note 2 For details concerning the CC Link refer to the CC Link Partner Association Reference CC Link Partner Association lt Precautions before Using CC Link Slave Unit gt 6 2 Dimensions FP gt CC Link slave unit FPG CCLS AFPG7943 000000 oko becos FPG CCLS QU LL s e e e e e Record of changes Manual No Date Desceiption of changes ARCT1F380E APR 2003 First edition ARCT1F380E 1 JUL 2005 2nd edition ARCT1F380E 2 NOV 2008 3rd edition Change in Corporate name ARCT1F380E 3 AUG 2011 4th edition Change in Corporate name ARCT1F380E 4 JUL 2013 5th edition Change in Corporate name Please contact Panasonic Industrial Devices SUNX Co Ltd W Overseas Sales Division Head Office 2431 1 Ushiyama cho Kasugai shi Aichi 486 0901 Japan Telephone 81 568 33 7861 Facsimile 81 568 33 8591 panasonic net id pidsx global About o
20. rom the system area 2 System area above can be referred when the FPO CC Link slave unit is used as the Expansion unit 1 3 1 0 area which is allocated to the remote register can be used in a word unit 4 Wiring For details refer to CC Link Cable Wiring Manual which can be downloaded from the Web site of CC Link Partner Association free of charge For your reference CC Link Partner Association Precautions before Using CC link Slave Unit of this manual English http Avww cc link org eng index html Japanese http www cc link org CC Link cables Use dedicated CC Link cables in the CC Link system If any other cable is used the performance of the CC Link system cannot be guaranteed Terminal resistor Cable Dedicated CC Link cables 1109 for CC Link Ver 1 10 Dedicated CC Link cables 130 Q Dedicated CC Link high performance cable Make sure to use only one type of cables CC Link cables or CC Link high performance cables If both types of cables are used together normal data transmission cannot be guaranteed For details concerning the specifications and connection for the dedicated CC Link cables contact the CC Link Partner Association la Reference CC Link Partner Association Precautions before Using CC Link Slave Unit gt Wiring with CC Link cables The cables can be connected without regard to the station No Make sure to connect a terminal resistor
21. t e e A e tu tete etii tec ise dii n tte tar 3 3 Allocation of Input Output and Shared Memosry rn 6 34 EPX CO LinkeSlave Uniku i Re t e tee o eee tete tds 6 3 2 FPO CG 10 A PR 12 BAM Error OCCUIS dd 13 9 1 Troubleshooting e lo nasa cd 13 5 2 ERR ALARM LED IO ANIM EN te 14 A O 15 8 Specifications dd ERN 15 AAA ON 17 Precautions before Using CC Link Slave Unit Mounting plate Note that the types of mounting plates used for FP X and FP0 are different Unit name including CPU Mounting plate to be used FP gt CC Link slave unit Slim type 30 mounting plate AFP0811 FPO CC Link slave unit Slim type FP0 mounting plate 0803 Installation of CC Link slave unit Normally any unit cannot be installed on the right side of the FP0 CC Link slave unit To assure the measurement accuracy it is not recommended for any unit to be installed on the right side of the FP0 thermocouple unit When the FP0 CC Link slave unit is used together with the FP0 thermocouple unit in a system FP0 CC Link slave unit can be on the right side of the FP0 thermocouple unit e Reference Measurement accuracy when the FPO thermocouple unit is used together with the FPO CC Link slave unit in a system 1 3 Unit Connection CC Link Partner Association 1F Chusanren Bldg 3 12 13 Shirakabe Higashi ku Nagoya 461 0011 JAPAN Phone 81 52 936 6050 F
22. ur sale network please visit our website Panasonic Industrial Devices SUNX Co Ltd 2013 July 2013 PRINTED IN JAPAN ARCT1F380E 4
23. urrently changed 10 3 2 1 Expansion Unit I O Allocation Remote input FPO side output FPO CC Link I O CC Link pee installation position master occupied Area Points p remote I O stations Expansion Expansion Expansion Note2 unit 1 unit 2 unit 3 1 0 16 Y20 2F Y40 4F Y60 6F RX00 0F Register 16 WY3 WY5 WY7 RWr 0 Register 16 WY4 WY6 RWr 1 1 Register 16 WY5 WY7 2 RWr 2 Register 16 WY6 RWr 3 s WY7 RX10 1F area Remote output FPO side input FPO CC Link I O CC Link nese installation position master occupied Area Points p remote I O stations Expansion Expansion Expansion Note2 unit 1 unit 2 unit 3 1 0 16 X20 2F X40 4F X60 6F RY00 0F Register 16 WX3 WX5 WX7 RWw 0 Register 16 WX4 WX6 RWw 1 1 Register 16 WX5 WX7 RWw 2 Register 16 WX6 RWw 3 Sr sel TS WX7 RY10 1F area Note 1 The expansion units closer to the control unit have the lower expansion unit number Expansion unit 1 2 and 3 Note 2 Remote I O RX RY RWr and RWw are the descriptions for the master station from MITSUBISH System area allocation bit Master station FPO CC Link Signal RX 0 A Y70 7A Not available RX B Y7B Remote station Ready RX C F Y7C 7F Not available RY 0 F X70 7F Not available a Note 1 Data cannot be written in the system area Data can be read f
Download Pdf Manuals
Related Search