S12 Series User manual-2013
Contents
1. Accumulative Display m ODO L Li km 2 Once total mileage up to 99999km 62149mile 99999 1 609mile the counter will restart from 00000 1 Display Range 00 0 99 9 TRIP Counter mile 2 When over 99 9km display stop counting won t restart from 00 0 1 Odometer indication display on ODO mode when Power On then switch to TRIP mode Operation status after 5 seconds 2 TRIP can be reset to 00 0 17 6 Headlight Control ITEM SPECIFICATION Take exterior headlight switch as determinant signal Operation Feature 1 Switch on off the head light by pressing button once then LED will turn on off simultaneously 2 LCD backlights turn on turn off with head light When motor stop the modulation down to 30 Headlight When motor act 10046 output power Headlight Usage Condition While a KEY OFF b Power Saving mode c Sleep mode all functions closed 1 2 2V gt WIP gt 2 8V 100 Full power 2 2 2V lt WIP gt 2 8V 100 Full power 3 Full Half power switch at real time Determinant Condition 4 The determination of Reversing Mode need to consider the motor direction and panel setting 1 Loop Load 24V 50W max 2 With short circuit and overload protection T Back up Lamp control Take exterior back up lamp switch as determinant signal Operation Feature 1 Switch on off the head light by pressing b2. m flashing warning sound act Press again to turn off left indicator Right direction lamp Fux e Press button Once warning sound act Press e gt again to turn off the Parking lamp function turn on right left indicators and flashing Parking lamp Usage Condition While a KEY OFF b Charging Mode c Sleep Mode all functions closed Warning Sound Frequency One short B1 sound per second 1 Load circuit for left direction light 24V SOW max Remarks 2 Load circuit for right direction light 24V SOW max 3 With short circuit and overload protection 19 11 Power Self Test When scooter power on the control panel will go through self test routine backlight Initial Status and all LCD segments will be tuned on for 3 seconds then switch automatically to the general operation mode ODO 12 Temperature Sensor Operation Feature Temperature detected by temperature sensor NTC from transformation with signal Tolerance 20 C 50 C TEMP 4 F 122 F When display C degree stand for Celsius thermometer Display Switch Button When display F degree stand for Fahrenheit thermometer 13 Reverse Indicator ITEM SPECIFICATION Take exterior forward backward switch as determinant signal When switch direct to forward no symbol on LCD Reverse symbol flashing on LCD Flicker Freque
3. Battery 1 Indicator Green Flash Power On S Orange Flash Pre Charge I Orange Charging Ow Green amp Orange Flash Charged 80 m Green Full Charged Flash Defected 2 SPECIFICATION Mol CMON BALS Model Input Voltage AC 100 240 V 50 60Hz Efficiency AC DC 85 min Operating Temperature 0 C 40 C Switching Method SWITCHING MODE Charging Method Constant current two stage constant voltage Battery Application 24V Lead Acid Rechargeable Battery 26Ahr 75Ahr 1 Short Circuit Protection Input Current AC 2 Reverse Power Protection Output Detection l 3 Overheat Protection 4 Charging Plug Protection Color Be 22 3 OPERATING INSTRUCTION 1 Make sure the battery charger output voltage is the same as the connecting battery 2 Plug in the power cord LED indicates green flash when AC power on 3 Connect the battery charger to the battery Start charging please refer to LED INDICATION 4 LED INDICATION 1 Green Flash Power on 2 Orange Charging 3 Orange Flash Pre charge 4 amp Orange Flash Charged 80 5 Green Full charged Floating charge 6 Red Flash Defect 5 TROUBLE SHOOTING 1 If green indicator is off Check AC input If it works functionally the battery charger may be defective 2 If green indicator keeps flashing and cannot turn to charging indication Check if the battery connector is connected successful
4. Imm 1 32 please have your tires replaced by your local dealer All upholstery can be washed with warm water and mild soap Occasionally check the seat and back for sagging cuts and tears Replace necessary Do not store your scooter in damp or humid conditions as this will lead to mildew and rapid deterioration of the upholstery parts All moving mechanism will benefit from simple lubrication and inspection Lubricate using petroleum jelly or light oil Do not use too much oil otherwise small drips could stain and damage carpets and furnishings etc Always perform a general inspection of the tightness of all nuts and bolts 26 TROUBLESHOOTING amp FAULT REPAIR S Drive controller Your scooter is fitted with S Drive controller which continuously monitors the operating conditions of your scooter If it detects a problem it will indicate with error message by flashing light on the power ON OFF light You must count the number of the flash and see the list to check what kind of error has happened according to the number If you experience any technical problems it is recommended that you check with your local dealer before attempting to troubleshoot on your Own The following symptoms could indicate a serious problem with your power scooter Contact your local dealer if any of the following arises 1 Motor noise 2 Frayed harnesses 3 Cracked or broken connectors 4 wear on any of tires 5 Jerky mo
5. altogether 5 level of adjustments It 1s applicable with around 120kg and each level can bear up to 13 5 kg Tooling bar OPERATION OF CONTROL PANEL LCD Liquid Crystal Display Power Scooter Control Panel TN Type Model Functions Buttons 2 3 4 5 6 1 8 9 gt LCD Liquid Crystal Display Power Indicator Battery remaining capacity and charging Indicator 6 squares Battery Icon Clock Hour Minute Second display and setting Speed Sensor 7 Segment display 2 5 digits 1 decimal km h mph symbol High Low Indicated as and L symbols Odometer ODO 99999km max TRIP 99 9 max Headlight Power saving mode Blue LED Back up Lamps Brake Reverse modes Orange LED Right Indicator Flash mode Green LED Left Indicator Flash mode Green LED Parking Lamp Including Reverse Mode left indicator and right indicator flashing simultaneously Red LED Malfunction Code 7 Segment display 1digit Warning symbol Red LED Power on Scan All LED turn on TEMP Gauge C and F modes Reverse Light Reverse symbol flashing Left Indicator control Right Indicator control W High low speed switch Parking 12 65 Headlight SET lt Back up Light LED Indicators Right amp Left indicator Green Parking light Red Warning light Red Back up lamps Yellow Headlight Blue LCD Bac
6. c Sleep Mode warning sound released 15 ITEM SPECIFICATION Remaining 40 2544 2 55 gt 25 44 3 70 gt 26 18 Charge Indication 4 80 gt 26 92 5 90 gt 28 5 6 100 7 F Increase 0 5 sec Frequency 1 Scale status only decrease won t increase 2 Take the PIN3 CH3 of charger as determinant signal enter Charging Mode when CH3 grounding L not only KEY ON or KEY OFF Operation Character k Above scale bar status only for reference must take the indicator of charger as the precise emarks diagnosis 16 Clock Meter ITEM SPECIFICATION Initial Setting Value Hour Min mode 12 00 1 Hour Min Display range AM12 00 PM11 59 Masc AM x x L Li When Hour is between 1 and 9 o clock displayed at 1 9 5 Odometer Operation Features Odometer detected by the signal of Opto Coupler then converts into distance f km h means the odometer displayed as kilometer Display Switch Button mph means the odometer displayed as mile 1 Display Range 00000 99999 mmm
7. control system The intensity of the EM energy can be measured in volts per meter V m Each powered scooter can resist EMI up to a certain intensity This is called immunity level The higher the immunity level the greater the protection At this time current technology is capable of providing at least 20 V m of immunity level which would provide useful protection against common sources of radiated EMI Following the warnings listed below should reduce the chance of unintended brake release or powered scooter movement that could result in serious injury 1 Do turn on hand held personal communication devices such as citizens band CB radios and cellular phones while the powered scooter is turned on 2 Beaware of nearby transmitters such as radio or TV stations and try to avoid coming close to them If unintended movement or brake release occurs turn the powered scooter off as soon as it is safe 4 aware that adding accessories or components or modifying the powered scooter may make it more susceptible to interference from radio wave sources Note It is difficult to evaluate the effect on the overall immunity of the powered scooter 5 Report all incidents of unintended movement or brake release to the powered scooter manufacturer and note whether there is a radio wave source nearby TURN OFF YOUR POWERED SCOOTER AS SOON AS POSSIBLE WHEN EXPERIENCING THE FOLLOWING Unintentional scooter movements Unintended or u
8. half year limited warranty gt Electronic Components and Charger One year limited warranty Warranty Exclusion The following items are not covered by warranty lt Motor brushes lt Wheel Tires lt Arm Pads lt Seat Cushion lt Fuses Bulbs lt Tiller Cover lt Rear Shroud lt Front Shroud lt Batteries and Consumable parts Any damage or defect of any nature occurring from the misuse abuse of the product improper Operation or improper storage is not to be covered The warranty 15 to start from the date of arrival of our products rd r HEARTWAY HEARTWAY MEDICAL PRODUCTS CO LTD NO 6 ROAD 25 TAICHUNG INDUSTRIAL PARK TAICHUNG TAIWAN 408 30
9. ND CLEARANCE LEG ROOM 340mm l 7 5 7 9 512 5125 DIMENSION COMFORT ADJUSTMENT Adjustments for Seating Comfort Press the bottom to adjust the height of the headrest The flip up armrest height can be adjusted by turnin the adjustment dial Adjust the seat back lever for seating back angle Turn the swivel lever downwards to rotate the seat Push front lever upwards to move the seat forward and backward Driving and braking Optional hand brake lever Reverse m A meum a Le For driving please pull the right throttle lever forward or the left throttle lever backward Please release the throttle lever to stop the scooter In the center position the magnetic motor brake system works also as a parking brake Optional there 15 a hand brake system available For safety when rolling at free wheel mode down slope the automatic brake will take action 10 if the transferring speed 15 more than 30 of the scooter s maximum speed T Please be noted that the scooter will be at free wheel Engaged EL mode when the motor is disengaged To use the parking brake you must move and lock Disengaged the lever into the engaged position Free Wheel Tiller Positioning Press down the lever and move it to your preferred position The adjustment of rear suspension svstem The softness of the rear suspension system 1 adjustable There are
10. USER MANUAL ae HEARTWAY HEARTWAY MEDICAL PRODUCTS CO LTD NO 6 ROAD 25 TAICHUNG INDUSTRIAL PARK TAICHUNG TAIWAN R O C 408 PUBLISHED SEP 6TH 2012 VERSION 1 PART NO 70030175 CONTENTS l SAFETY INS PRU CG IID Nu u uu u un uuu yu 2 ELECTOMAGNETIC INTERFERENCE 7 5 SPECIFICATIONS aku 8 d PRODUCE DIMENSION aaa usa 9 23 COMFORT ADJUSTNIBNT u 10 6 OPERATION OF CONTROL PANEL 12 T CHARGING INSTRUCTION 22 8 BATTERY INSTRUCTION amp MAINTENANCE 24 9 SCOOTER MAINTENANCE amp REPAIR E aa 25 10 TROUBLESHOOTING amp FAULT REPAIR 27 ti CIRCUIT DIA GRA Wh 28 12 HEARTWAY S PATENT SUSPENSION SYSTEMI 28 BOM LIST DRAW ING atus ua Un EV EHI 29 WARRANTY DECEARATIQN u i ku u ua 30 SAFETY INSTRUCTION General Do not make a sharp turn or a sudden stop while Do not ride your scooter in traffic riding your scooter Do not attempt to climb curbs greater than Do not leave your hands and legs off the scooter limitation show on Technical Specification when driving Do not ride your scooter during snow in order to Do not allow unsupervised children to play near avoid accident on slippery road th
11. Ug 1007 1007 372 1007 ELI 1 tack HEARTWAY S PATENT A brand new double A arms suspension system 512 BOM LIST DRAWING CT INDICATOR LIGHT FUL 2 INDICATOR LIGHT FUR 3 FD COVER HANDLE CAP 8 TILLER FF COVER 8 RUBBER DUST COVER 7 TILLER FR COVER DRINK BRACKET 8 HEAD LIGHT FDL 40 HEAD LIGHT FDR FLOOR FRONT BUMBER LAMP BASE 4 CARPET 18 FENDER REAR BUMPER 47 SIDE COVER R REAR VIEW MIRROR CONTROL PANEL 20 BATTERY BODY FRAME ALUMINUM RIM 23 TYRE INNER RIM 25 BATTERY UPPER SHROUD 98 SUSPENSION 0780 SIDE COVER 28 BATTERY LOWER SHROUD 29 SEAT ASM 80 SEAT SLIDING RAIL 21 SEAT BASE 32 SEAT SLIDING POST 33 SAFETY BELT 29 35 REAR LIGHT 38 BRACKET FOR FENDER 372 FF COVER BRACKET 28 FRONT BUMPER BRACKET ad wiGWAG 40 SPACER FOR POTENTIOMETER 4T TILLER FRAME 42 TILLER RAM MECHANISM 43 RD SHROUD 42 LIGHT SEAT 45 STEM 48 POTENTIOMETER COMBINATION 47 SUSPENSION BRACKET 48 TRIANGLE LIGHT 60 SPEEDOMETER LINE ARM BRACKET WARRANTY DECLARATION Quality Warranty Declaration Products are to be for purpose and of excellent quality and performance For valid warranty claims Heartway will at their discretion replace repair refund items mutually agreed to be defective Heartway s Warranty as Following Frame Two year limited warranty Controllers One and a
12. ained in assisting a scooter user in various daily living activities Consult with your physician if you are taking any medication that may affect your ability to operate your scooter safely Do not attempt to lift or move a power scooter by any of its removable parts including the armrests seats or shrouds Personal injury and damage to the power chair may result Never try to use your scooter beyond its limitations as described in this manual Please do not sit on your scooter while it is in a moving vehicle Keep your hands away from the wheels tires while driving scooters Be aware that loose fitting clothing can become caught in the drive tires Consult your physician if you are taking prescribed medication or if you have any certain physical limitations Some medications and limitations may impair your ability to operate scooters in a safe manner Be aware when the drive mode is unlocked or locked Don t remove anti tipper if there 1s any tipper equipped with the scooter Contact with tools can cause electrical shock and do not connect an extension cord to the AC DC converter or the battery charger Do not attempt to lift or move your scooter by any of its removal parts such as the armrests seats or shroud When climbing an incline don t drive at an angle up the face of the incline Drive your scooter straight up the incline This greatly reduces the possibility of a tip or a fall Don t climb a slope steeper than the scooter s limi
13. d your power scooter may not be able to operate In extreme high temperatures 1 may operate at slower speeds due to a safety feature of the controller that prevents damage to the motors and other electrical components ELECTROMAGNETIC INTERFERENCE EMD The rapid development of electronics especially in the area of communications has saturated our environment with electromagnetic EM radio waves that are emitted by television radio and communication signals These EM wave are invisible and their strength increases as one approach the source All electrical conductors act as antennas to the EM signals and to varying degrees all power wheelchairs and scooters are susceptible to electromagnetic interference EMI The interference could result in abnormal unintentional movement and or erratic control of the vehicle The United States Food and drug Administration FDA suggests that the following statement be incorporated to the user s manual for all power scooters like the S12 S12T S12S S12X Power scooters may as susceptible to electromagnetic interference EMI which is interfering electromagnetic energy emitted from sources such as radio stations TV stations amateur radio HAN transmitter two way radios cellular phones and alarm systems of shops The interference from radio wave sources can cause the power scooter to release its brakes move by itself or move in unintended directions It can also permanently damage the powered scooter s
14. e check all electrical connections and make sure they are tight and not corroded Please check all harness connections and make sure they are secured properly Please check the brakes Weight limitation Please refer to the specifications table for weight capacity information Power scooter 1s rated for a maximum weight capacity Stay within the specified weight capacity for your scooter Exceeding the weight capacity voids your warranty Heartway will not be held responsible for injuries or property damage resulting from failure to observe weight limitations Don t carry passengers on scooters Carrying passengers on scooter may affect the center of gravity resulting in a tip or a fall Tire inflation If your scooter is equipped with pneumatic tires it 15 necessary to check air pressure at least one time a week Proper inflation pressures will prolong the life your tires and ensure the smooth operation while riding Do not under inflate or over inflate your tires It is critically important that 30 25 psi 2 2 4bar tire pressure be maintained In pneumatic tires at all times Inflating your tires from an unregulated air source could over inflate them resulting in a burs tire Temperature JE Some of the parts of the power scooter are susceptible to change temperature The controller can only operate in temperature that ranges between 25 C 50 C At extreme low temperatures the batteries may freeze an
15. ed WEEKLY CHECKS 1 Your power scooter comes with standard pneumatic tires If your power scooter comes with optional air tires make sure to maintain the pressure of the tires between 30 35 psi MONTHLY CHECKS 1 Visually inspect the controller harnesses Make sure that they are not frayed cut or have any exposed wires SEMI ANNUAL CHECKS 1 Check the motor brushes We recommended that your authorized dealer inspect the brushes every six months or sooner if your power scooter is not operating smoothly If inspection determines excessive wear on the brushes they must be replaced or motor damage will result Warning Failure to maintain the brushes could void the power scooter warranty To inspect or replace the motor brushes Unscrew the motor brush caps 2 Remove the brushes 3 Inspect the brushes for wear 4 Replace the brushes if necessary New Motor Brush orn Motor Brush Motor Brush caps Inspect the state of the battery terminals every six months Make sure that they are not corroded and the connections are tight Periodically apply a thin film of petroleum jelly on the surface of terminals to guard against corrosion 25 Make sure to keep the controller clean while protecting it from or water Never hose off your power scooter or place it in direct contact with water Keep wheels free from lint hair sand and carpet fibers Visually inspect the tire tread If less than
16. ge at least once every month to avoid deterioration of the batteries BATTERY INSTRUCTION amp MAINTENANCE Read through the charger operating instruction before using it Make sure you charge the battery every time after you use the power chair or scooter Charge the battery at least 24 hours a week if the power chair or scooter has not been used This 1s to make sure that the electrolyte 1s always at the top level If the battery cannot be charged Orange light cannot turn to Green or if the Orange light turns to Green immediately please check it with the technicians The battery may be defective The voltage difference between the two batteries on a power unit cannot be more than 0 5 V the battery case should be inspected for cleanliness and evidence of damage If the charger indicates red light please kindly check if the charger is defected or if the cable wiring connection 1s poor Please keep the battery Gand connectors clean otherwise the charging condition will be poor 24 SCOOTER MAINTENANCE amp REPAIR Your power scooter is designed for minimal maintenance However like any motorized vehicle it requires routine maintenance To keep your Vita Scooter for years of trouble free operation we recommend you follow the following maintenance checks as scheduled DAILY CHECKS 1 Visual check on the conditions of tires 2 Inspect the battery condition meter on the controller to determine if batteries need to be charg
17. is equipment while the batteries are charging Warning Don t operate your scooter for the first time without completely reading and understanding this user manual 1 Don t operate scooter on public streets and roadways Be aware that it may be difficult for traffic to see you when you are seated on the scooter Obey all local pedestrian traffic rules Wait until your path is clear of traffic and then proceed with extreme cautions 2 To prevent injury to yourself or others always ensure that the power is switched off when getting on or off of the scooter 3 Always check that the drive wheels are engaged drive mode before driving Do not switch off the power when the scooter 15 still moving forward This will bring the chair to an extremely abrupt stop 4 Do not use this product or any available optional equipment without first completely reading and understanding these instructions If you are unable to understand the warnings cautions or instructions contact a healthcare professional the dealers or technical supports before attempting to use this equipment otherwise injury or damage may occur 10 11 12 15 14 15 16 17 18 19 20 There are certain situations including some medical conditions where scooter user will need to practice operating the scooter in the presence of a trained attendant A trained attendant can be defined as a family member or care professional especially tr
18. klight LED White CONI 20PIN AMP Meter Angle at 30 of elevation while scooter assembly LCD orientate to six o clock Handle Cover 2 General Characteristic Performance Test 20 5 C SPECIFICATION RESULT 2 1 Headware Circuit Consuming Current Dynamic 200 mA max Backlight and LED light status mA 24 0V OM E Static 5 mA max X Key OFF status 13 1 gt Speed Sensor and Display ITEM SPECIFICATION Operation Features Speed detection by speed sensor from transaxle with conversion at 1800rpm equal to 60km h Digital Range 0 0 99 Display Switch Button Initial setting at km h switch to MPH by MODE and buttons 2 High Low Speed ITEM SPECIFICATION Operation Features 1 Switch High Low speed by pressing button once as control signals Press one time High speed lt lt gt gt Low speed 2 Take exterior turn switch as determinant signal as control signals Symbols on LCD H symbol means High Speed L symbol means Low Speed Flicker Frequency 14 3 gt Power Indication ITEM SPECIFICATION Scale Bar Remaining and Flashing Low power ONN LED Flashing Warning Flicker Frequency 1 Scale status only decrease won t increase 2 When the remaining capacity was less than 30 warning sound two short sounds il act at 5 seconds intervals While a Key Off b Charging Mode
19. ler connections are secure 10 Bar An excessive voltage has been applied to the controller This is usually caused by a poor battery connection Check Ihe batery connections 2 CIRCUIT DIAGRAM gus wo ang Hr sita n Tots red brem un p jun shes a EZ LH qa ka ka gio ns m 1 L1 n gu eder MI P a i sb ino 1615 bak L hs whee gs 1007 misi ne 1075 hasa 10 ee ped idem goa n d Fb anm charger fret i i Hos ibe fun eter r y sper labile H 1I lig l ras 3 ap key ma Raza papel EDT pael i TERA imime Re rA LI u RHINO Controller F 110A we T Mg 7l 29 mar signal 7 HIT ped ay T8 1 s Iw 01728 E ras rl ade amp yLED ui vw Sali EEEF Dee 018 tan maed ier aider deret eet Fed ie Le 7 DW Xam maak E ped SH oL Bet Taie Las I ES Tu sam tal k IOo leit speed 22 1207 thure 1007 Bez 1007
20. ly Check if there is any short circuit on the output connection The battery charger may be defective if the battery connection works functionally 3 If red indicator keeps flashing Check if the battery connection is reversed Check if there is any short circuit on the output connection Check if the environment temperature is too low 0 C The battery charger may be defective if the red indicator still keeps flashing 4 Charging indicator orange cannot turn to green The battery might be defective please stop charging and have the battery be repaired 5 If the charging indicator orange turns to green fully charged immediately The battery may be in well charged condition The battery may be defective if the battery is not fully charged 23 6 CAUTION 1 Before using the battery charger read all instructions and cautionary markings 2 Use the battery charger in a well ventilated area 3 To avoid the risk of injury charge only lead acid gel cell type rechargeable batteries 4 Please turn off the power after charging Charging Port Important Always charge your batteries In well ventilated areas The charger is intended for indoor use only Please protect it from the moisture For maximum performance it is recommended that you replace both batteries at the same time if the batteries are weak If the scooter will not be used for a long period of time arrange to have the batteries rechar
21. ncontrollable direction Unexpected brake release The FDA has written to the manufacturers of power scooters asking them to test new products to be sure they provide a reasonable degree of immunity against EMI The FDA requires that a powered wheelchair should have an immunity level at least 20 V m which provides a reasonable degree of protection against more common sources of EMI The higher the immunity level the greater the protection Your powered scooter has an immunity level of 20 V m which should protect against common sources of EMI Warning The scooter itself can disturb the performance of the electromagnetic fields such as emitted by alarm systems of shops 512 5125 512 TECHNICAL SPECIFICATIONS SI2T S12 VITA VITA 125 VITA SI2T 5125 S12X WEIGHT CAPACITY I60kgs 350 l60kgs 350 160kgs 350 160 350 SEAT TYPE SIZE 330mmxlO00m 330mmxlO0m 330mmx100m 380mmx160m 13 3 x m 15 x6 3 330mmx 100m 330mmx 120m 3 x4 4 m 13 x4 8 ANTI TIPPER 13KM H 13KM H 18 18 BATTERY SPECIFICATIO BATTERY RANGE 30km S0km _ 35km 45km 40km sS0km 25km 45km CHARGER TYPE SAmp Off Board120 240 Board120 240 Board120 240 Board120 240 Volt 50 60Hz Volt50 60Hz Volt50 60Hz Volt 50 60Hz 120Amp 120Amp 140Am 200Am WEIGHT W BATTERY 150kgs 330 WEIGHT W O BATTERY 95kgs 209 Ibs 93kgs 205 Ibs lt 95 242 Ibs 79 SEAT HEIGHT 460mm BACK HEIGHT WHEEL BASE 1025mm GROU
22. ncy 20 14 Buttons ITEM SPECIFICATION Displ n Press for 3 seconds to reset TRIP at 00 0 Press and simultaneously for more than 2 seconds to enter Setting Mode then Hour MIN start flashing 1 When Hour flashing Press to increase of number then press toenter Setting Mode of MIN 2 When MIN i flashing Setting Mode Press to increase of number then press toenter Setting Mode of km h amp mph 3 When km h or mph flashing Press to choose km h or mph type then press to enter Setting Mode of C F 4 When C or F flashing Press to choose C or F Under setting mode if below situations happened will auto save the last setting value then from Setting escape to general operation mode 1 No any operation of ADJ button for 20 sec 2 Press MODE and at same time for more than 2 sec 1 Hour Min km h or mph or F offer Cyclical Switch function 2 When adjusting Hour Min press to increase number if press for Operation Status more than 2 seconds the number will increase continuously until button released setting value with Cyclical Switch function only 2 seconds from 0 to 9 If Hour y less than 10 denary 0 doesn t display Remarks Button tones one short sound 2l CHARGING INTRUCTIONS APPERRANCE Battery Charger Instruction DPower Cord E EE Output Plug to
23. tation Don t attempt to have your scooter proceed backward down any step curb or other obstacle This may cause the scooter to fall or tip Always reduce your speed and maintain a stable center of gravity when cornering sharply Don t corner sharply when driving scooters at higher speeds Operating in rain snow salt mist conditions and on icy or slippery surfaces may have an adverse affect on the electrical system Never sit on your scooter when it 15 being used in connection with any type of lift or elevation product Your scooter is not designed with such use in mind and any damage or injury incurred from such use 1 not the responsibility of Heartway Modifications Heartway Medical Product has designed and engineered power scooters to provide maximum utility However under no circumstances should you modify add remove or disable any part or function of your power scooter Personal injury and damage to the power chair may result l Do not modify your power scooter in any way not authorized by Heartway Do not use accessories if they have not been tested or approved for Heartway products 5 gt Get to know feel of your power scooter and its capabilities Heartway recommends that you perform a safety check before each use to make sure your scooter operates safely Inspections prior to using your power scooter If equipped with pneumatic tires please check for proper tire inflations Pleas
24. tion 6 Pulling to one side 7 Bent or broken wheel assemblies 8 Does not power up 9 Powers up but does not move PG S Drive controller PG D Drive Controller continuously monitors the operating conditions of your scooter If it detects a problem it will indicate with error message by flashing light You must count the number of the flash and see the list to check what kind of error has happened according to the number S Drive Controller Troubleshooting 1 Bar The battery needs charging or there is a bod connection to the battery Check the connections to Ihe battery If the connections are good try charging the battery 2 Bar There bad connection fo Ihe motor Check all connections between the motor and T the controller The motor has a short circuit to a battery connection Contact your service agent The freewheel switch is activated or the manual brake disengagement mechanism is operated Check the position of the switch or lever Not usec The S drive is being inhibited from driving inhibit 2 is active This may be because the battery charger is connected or the seat is not in the driving position A throttle fault is indicated Make sure that the throttle is in the rest position before switching on the scooter A controller fault is indicated Make sure that all connections are secure The parking brakes have a bad connection Check the parking brake and motor connections Make sure the control
25. utton eu once then LED will turn on off simultaneously 2 LCD backlights turn on turn off with head light When motor changes from act go forward to stop the lamp reinstated after flashing Control Mode for 3 sec Brake lamp Mode Determine as Reversing Mode back up lamp keep flashing Reversing lamp Mode Reverse warning sound can be set by panel Turn on Turn off While a KEY OFF b Charging Mode c Sleep Mode all functions closed Usage Condition Brake lamp Reversing lamp Mode won t be limited by Back up lamp switch on or off Flicker Frequency 1 2 2V gt WIP gt 2 8V 50 Half power 2 2 2V lt WIP gt 2 8V 100 Full power Determinant Condition 3 Full Half power switch at real time 4 The determination of Reversing Mode need to consider the motor direction and panel setting 1 Loop Load 24V 50W max 2 With short circuit and overload protection 8 9 10 Indicators and Parking Lamp Control ITEM SPECIFICATION Operation Feature Take exterior left right indicators and parking lamps switch as the determinant signal gt Press button once the right indicator and s turn off left indicator and lt 1 L F flashing warning sound act Press again to turn off left indicator Control Mode Left direction lamp 1 I Press button e once right indicator turn off left indicator and SU 078
Download Pdf Manuals
Related Search