LED MH315T COB
Contents
1. INYO Bedienungsanleitung User manual LED MH315T COB www destilan deutschland de BCE VY Table of contents INTRODUCTION RE 2 SAFETY INSTRUCTIONS eege dE eege 2 OPERATING DESCRIPTION OF THE DEVICE E 4 INSTALLATION as ee ea EISE Stand gone ODE ANON ME Master Slave Ee DE DMA CONVOCA Opera OM EE 6 AQdLeSSINng ss ee ae 6 GOO DO AIG a ee a ne aa ne ae aaa 6 OMA OOO CO leere 7 TECHNICAL SEET HEH 7 co ms rm rm rm rm mm 22 22 N CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing For your own safety please read this user manual carefully before you initially start up Every person involved with installation operation and maintenance of this fixture has to be qualified follow the instruction of this manual consider this manual to be part of the total product Keep this manual for the entire service life of the product pass this manual to every future owner or use of the product INTRODUCTION Thank you2. for choosing our fixture if you follow up the instruction given in this manual we be sure that you will enjoy this product for a long period of time SAFETY INSTRUCTION eer rm rm rm rm rm rm rm rm rm CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching the wires un u em wm wm 2 eg a Te u a eg Ze a 1a esse Sa Zus Te Ya Fe a an a a a Va a a a a a tT gt es De a elt et a Zeen Fa a Sam Sa Ge ee ge enee et C e This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instruction and warning notes written in this user manual Important Damages caused by the disregard of this user manual are not subject o warranty the dealer will not accept liability for any resulting defects of problem If the device had been ex
3. ansmission on the DMX data link CONTROL BOARD The control board offer several features you can simple set the starting address run the pre programmed program or make a reset OOO O MODE IESC DOWN ENTER he main menu is accessed by pressing the Mode Esc button Browse through the submenu by pressing Up or Down Press the Enter button in order to select the desired menu You can change the selection by pressing Up or Down Confirm every selection by pressing the Enter button You can leave every mode by pressing the Mode Esc button The functions provided are described in the following setting 4 MENU The device has two operation modes It can be operated in Stand Alone or in DMX controlled A001 address code setting from A001 A512 AU01 auto moving speediness AUO2 slow speed auto moving SNO1 Sound control for color changing SNO2 Sound control for strobe RPOF Set pan to forward rotating RPON Set pan circumrotate reverse RTOF Set tilt to forward rotating RTON Set tilt circumrotate reverse RDOF set the LED readout to non inverting RDON Set the LED readout to inverting DFON Default output setting Note output default setting address code is 001 pan is positive circumrotate tilt is positive circumrotate LED positively reveal 4 3 User configurations Setup single desk light s autocephaly moving mode auto running Press the MENU until it shows AUO1 Use the UP DOWN buttons to set
4. lor Change 0 15 Neutral 16 31 Red 32 47 Green 48 63 Blue 64 79 Green Blue 80 95 Red Green 96 111 Red Blue 112 255 Red Green Blue Switching the LEDs Strobe Reset 0 10 LED OFF 11 20 Neutral 21 30 Reset 31 200 Strobe effect with increasing speed 201 250 Random strobe effect with increasing speed 251 255 Neutral Dimmer oe 0 255 Pan fine Tilt Fine TECHNICIAL SPECIFICATIONS Voltage 110V 250V 50 60Hz Power consumption 65W LED 3pcsX15w RGB 3 in 1 COB LEDs Gross Weight 3 5Kgs 28 H x 22 W 270 mm 4 UN BCE wwvw destilan deutschland de
5. posed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it had reached room temperature Please make sure that there are no obvious transport damages should you notice any damages on the AC connection cable or on the casing do not take the device into operation and immediately consult your local dealer The device falls under protection class The power plug must only be plugged into a protection class outlet The voltage and frequency must exactly be the same as stated on the device Wrong voltages or power outlets can lead to the destruction of the device and mortal electrical shock Always plug in the power plug last The power plug must always be inserted without force Make sure that the plug is tightly connected with the outlet Never let the power cord come into contact with other cables Handle the power cord and all 2 connections with the mains with particular caution Never touch them with wet hands as this could lead to mortal electrical shock Never modify bend strain mechanically put pressure on pull or heat up the power cord Never operate next to sources of heat or cold Disregard can lead to power cord damages fire or mortal electrical shock The cable insert or the female part in the device must never be strained There must always be sufficient cable to the device Otherwise the cable ma
6. thin a distance of min 0 5m DMX 512 connection connection between fixture The wires must not come into contact with each other otherwise the fixture will not work at all or properly Please note the starting address depends upon which controller is being used Only use a DMX cable and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture to another Occupation of the ALR connection DMX output DMX input ALR mounting socket XLR mounting plug Ground Ground Signal 2 Signal 3 Signal Signal Connection with the mains The occupation of the connection cables is as follows Cable Pin International iene _ The earth has to be connected The device must only be connected with an electric installation carried out in compliance with IEC standards OPERATION After you connected the effect to the mains The fixture starts running Stand Alone operation In the stand alone mode the fixture can be use without controller Master slave operation The master slave operation enables that several devices can be synchronized and controlled by one master device DMX controlled operation You can control the projectors individually via your DMX controller Addressing The control board allows you to assign the DMX starting address Note it s necessary to insert the XLR termination plug with 120ohm in the last device in the link in order to ensure proper tr
7. to AUO1 or AUO2 Press ENTER to confirm Setup single desk light s autocephaly moving mode sound control Press the MENU button until it shows SNOF Use the UP DOWN buttons to set to SNOF press ENTER to confirm Master slave mode auto running sound control This mode will allow you to link up 32 units together without a controller Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the units Proper performance it may be necessary to use a terminator at the last fixture For more information about terminators Set the desired master mode Automatic program mode or sound controlled mode for the master device send the DMX address 1 for all slave devices Please refer to the instruction under control board To set the pan to reverse Press the MENU until it shows RPOF Use the UP DOWN buttons show RPON press ENTER to confirm To set the tilt to reverse the MENU until it shows RTOF Use the UP DOWN buttons show RTON press ENTER to confirm To set the LED readout to 180 rotating the MENU until it shows RDOF Use the UP DOWN buttons show RDON press ENTER to confirm Resume reverse Windows default Press the MENU until it shows DFON Dress ENTER to confirm DMX protocol 11 DMX channel mode Channel SEN movement 0 630 Tilt Tilt movement 0 180 Pan Tilt speed Pan amp Tilt soeed adjustment Red Green Blue Co
8. y be damaged which may lead to mortal electrical shock Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time If extension cords are used make sure that the core diameter is sufficient for the required power consumption of the device All warnings concerning the power cords are also valid for possible extension cords DESCRIPTION OF THE DEVICE Features gt 11 channel DMX 512 gt Pan 540 tilt 180 gt Variable electronic strobe gt Variable electronic dimmer 0 100 gt LED display menu with invert gt Reset to factory settings option gt Pan tilt invert option gt Fan cooled INSTALLATION Rigging The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation IMPORTANTIOVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE including calculating working load limits installation material being used and periodic safety inspection of all installation material and the projector If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury and or damage to property The projector had to be installed out of the reach of people DANGER OF FIRE When installing the device make sure there is no highly inflammable material decoration articles etc wi
Download Pdf Manuals
Related Search