Instruction Manual
Contents
1. HOPPER coffee bean container COFFEE GRINDING ADJUSTMENT DISK GRINDING ADJUSTMENT DISK HANDLE SERIAL NUMBER LABEL DOSER COVER aar LOCKING SLIDE paS E DOSER 4 rA COUNTER B COFFEE PRESSING DEVICE L gt DOSING LEVEL ey FILTER HOLDER FORK SS SWITCH lt O 4 PACKAGING On opening the packaging check carefully to make sure the appliance is intact and that there are no signs of damage If in any doubt do not use the unit and contact personnel with the appropriate professional skills The packaging materials must be kept out of the reach of children as they repre sent a potential source of danger Keep the packaging until the warranty has expired 5 DISPOSAL Do not litter dispose of the packaging materials according to the laws in force Should you decide not to use the appliance any more remember to unplug it so that it cannot be used and then cut the cable in the point where it comes out of the appliance Contact specialized firms for information on the disposal of the components of the appliance 6 USE This appliance has been designed solely for grinding coffee beans Any other use is understood to be improper and consequently hazardous The manufacturer cannot be held responsible for any damage as a result of improper or incorrect use Do not use the appliance for grinding other types of food or anything else Do not use the doser grinder doser version to store foods or measure them THE COFFE2. outlet of the ground coffee on the bot tom of the doser When a more thorough cleaning is required the operation must be performed only by skilled technical personell after disconnecting the appliance from the power supply according to the following instructions Remove the coffee outlet guard unscrewing the relevant screws 2 Unscrew the hexagonal head screw that fix the coffee dose adjustment knob 3 Unscew anticlockwise the coffee dose adjustment knob holding the doser s stars unit female dosing star and the upper dosing star pushed down 4 Remove the doser s stars unit 5 Remove the central spring 6 Clean thoroughly the bottom of the doser especially the sharp edges on sight and the outlet of the ground coffee In order to reassemble the doser follow the previous instructions in inverted order pay attention that the feather of the coffee outlet covering section plate is correctly set in the proper slide on the side of the basin Spout Coffee grinder with bag holder Wipe clean the spout from which ground coffee is released using a dry cloth All right reserved It is prohibited to reproduce adapt or translate this document without prior written authorization First Editon 2001 Last revised SJO7 07 2009
3. CONTENTS I 2 3 4 5 6 7 8 9 10 11 12 13 14 FOFEWONd sere reru PAET REREPAN OER EEE RRR page 2 DIMENSIONS sergas eeg ee RE E E E eee ee sees 2 General description cece ccc ce eee teens 3 PACKAGING wedi eoteceseusdneee tees unecauesseeus eaechew ens 3 DISDOSAL 2224242506 ar euestesoet canes eee ens ake E E 3 MISC 4 goon eae ew eh 2 ee ee ee ee ek ee ees 4 Installation and wiring oc20 ev cccee noe cee aeyenee eGo seen eenawes 4 Operation of the appliance cece eee eens 5 Warnings regarding operation 0 cece eee eee 8 Safety GEVICES conc ecunciastosweede og eee eabeteu meee r R ES 8 Warnings regarding safety 0 ce eects 9 INGISCTEVElS 225 oncueescecey passa sees een done ee eee aoe 10 PIGIMCGNANGCe ssrcricpresiadaaaii tamis aa a a iaaa a a ia I Cleaning the appliance 2 4c45 045 ecu ne 5cieroeb eee eeedeeneeeden I FOREWORD Read this manual from cover to cover before using the appliance as it contains important instructions for the safety operation and maintenance of the appliance Look after this manual and keep it in a safe place The manufacturer reserves the right to make changes to the product and to the manual 2 DIMENSIONS GRINDER DOSER GRINDER DOSER i o mai 61 4 Te 18 3 4 1 alternative height with optional hopper GRINDER DOSER COFFEE GRINDER SUPER JOLLY SUPER JOLLY 3 GENERAL DESCRIPTION HOPPER COVER
4. E GRINDERS AND COFFEE GRINDER DOSERS MANUFACTURED BY OUR COMPANY ARE INTENDED FOR SKILLED PERSONNEL ONLY FOR PROFESSIONAL USE AND NOT FOR HOUSEHOLD USE The user must be an adult Do not allow children or incapable persons to use the appliance 7 INSTALLATION AND WIRING The appliance must be installed by skilled technical personnel in conformity with the safety rules in force Incorrect installation may result in injury of persons or animals or damage to property for which the manufacturer cannot be held responsible The appliance must be placed on a stable flat surface Before plugging in the appliance make sure the voltage and frequency values of the supply mains correspond to the ratings indicated on the label featuring the appliance s technical data e The wall socket must be fitted with an efficient earth contact Consequently it is essential to make sure the earth system is efficient and in conformity with current safety rules If in any doubt have the system thoroughly checked by per sonnel with the appropriate professional skills IT IS COMPULSORY TO EARTH THE APPLIANCE The manufacturer cannot be held responsible in the event this regulation is not complied with e t is essential to make sure the ratings of the system are suitable for the power absorbed by the appliance as indicated on the label featuring the technical data and that the wall socket is protected against overcurrents e Do not use extension cables p
5. NTI NUOUS WORKING In order to achieve good grinding it is nonetheless recommended to operate the appliance at intervals allowing it to operate for no more than 10 15 minutes at a time 10 SAFETY DEVICES e THERMAL OVERLOAD PROTECTION The appliance s motor is protected against overheating resulting from overcur rents by a thermal overload protection which when tripped cuts off the power supply to the motor Should the protection trip as a result of anomalous opera tion such as the grinding blades jamming the appliance must be turned off using the on off switch UNPLUGGED FROM THE MAINS AND SKILLED TECHNI CAL PERSONNEL CONTACTED NEVER PERFORM ANY WORK ON THE APPLIANCE WHILE IT IS ATTACHED TO THE MAINS TO AVOID THE RISK THAT MOTOR TURNS ON SUDDENLY If the appliance overheats as a result of the motor stopping allow the appliance to cool down before performing any repair work e SAFETY SCREWS e The hopper must always be attached to the upper grinding blade hol der using the relevant screw which must not be removed by the user under any circumstances e In order to prevent the adjustment disk from being 25 removed which would HOPPER COFFEE OUTLET make the rotating parts sare GUARD e SCREW accessible there is a safety screw on the actual SS SSS ALTERNATIVE TAPPED HOLE disk said screw must be positioned in whichever of the two holes on the disk enables the wider and most suitable range of grinding adju
6. PRESSING grinder doser version STATIC PRESSING DEVICE Place the filter holder against the underside of the pressing device and push upwards SPRING PRESSING DEVICE Place the compacting disk against the upper face of the filter holder inserted in the fork shaped support and press down on the spring pressing device knob 9 WARNINGS REGARDING OPERATION e Do not leave the appliances turned ON without coffee in the hopper e In the grinder doser version avoid pulling the doserlever partially always pull it all the way In the coffee grinder version it is essential that nothing hinders the flow of ground coffee from the outlet in any way in order to prevent the risk of the appliance stopping Consequently avoid using coffee bags which are too small with respect to the amount of coffee to be ground At the end of each grinding cycle shake the handle of the pipe for a complete outlet of the coffee e FIRST INSTALLATION For the correct use of the grinding blades at the first installation or whenever the grinding blades have been replaced grind some doses of coffee Do not use those first doses e OPERATING RANGE OF THE MOTOR IN THE VERSIONS WITH SINGLE PHASE MOTORS OBSERVE THE DUTY CYCLE STATED INTHE LABEL LOCATED ON THE SIDE OF THE APPLIANCE E g a data on the label 35s ON 45s OFF points out an allowed duty cycle of 35 seconds switched on and 45 seconds switched off APPLIANCES WITH THREE PHASE MOTORS ARE ALLOWED FOR CO
7. URNING OFF THE APPLIANCE USING ITS MASTER SWITCH DOES NOT ASSURE THE SAME CONDITIONS OF SAFETY e When the appliance is left unattended the appliance s power supply must be disconnected using its master switch for example at night during work breaks midweek closing or holidays e Do not let liquids of any kind come into contact with the internal or external parts of the appliance e Never put ground coffee in the hopper intended only for coffee beans e Do not tamper with the appliance e DO NOT TUG ON THE SUPPLY CABLE TO UNPLUG THE APPLIANCE FROM THE MAINS e Do not touch the appliance with damp or wet hands or feet e Do not use the appliance barefoot The manufacturer cannot be held responsible for bodily injury or damage to pro perty if these regulations are not complied with 12 NOISE LEVEL EEC Countries The maximal noise emission of our coffee grinders or grinder dosers valued as acoustic power is 8l dB A measured in ISO 3741 reverberating chamber according to EN 60704 1 1998 and EN 60704 3 1996 The daily personal noise exposure of a worker due only to an appliance s limit operation of 240 min per eight hours is 78 dB A according to ED 86 188 EEC and ED 2003 10 EEC Therefore during he appliance s normal operation no pro visions are to be taken in order to prevent such risks arising or likely to arise from noise exposure at work articles 3 8 of ED 2003 10 EEC USA amp CANADA The noise level of
8. ally turn the knob anticlockwise all the way AUTOMATIC GRINDER DOSERS In order to power up the appliance turn the on off switch knob to I In order to swit ch the appliance on manually the switch knob must be turned all the way to START The appliance starts automatically every 2 portions of coffee every 6 portions in the model MINI LUX and in the versions with shorter doser group It switches off automatically when the doser is filled with ground coffee In order to switch off the appliance manually set the on off switch knob to O ADJUSTING GRINDING In order to achieve finer or coarser grinding the adjustment disk located under the hop per must be adjusted using the relevant COARSER GRINDING e LN handle In order to increase the coarseness of the ground coffee the disk must be rotated clockwise to decrease turn the disk anticlockwise The disk remains in the chosen position without having to be locked in place The adjustment must be performed with the motor on and preferably without any coffee between the grinding blades Grind small amounts of coffee in order to determine the optimal degree of fineness In the grinder doser version if the coffee comes out of the espresso coffee machi ne very quickly it means the coffee is ground too coarse Vice versa if it comes out too slowly it means the coffee is ground too fine Nonetheless bear in mind that there are many conditions liable to influence the correct supply s
9. appliance in rooms where water jets are used for cleaning THE APPLIANCE MUST BE CLEANED PERIODICALLY BY SKILLED TECHNI CAL PERSONNEL ONLY Use perfectly clean disinfected cloths or brushes for cleaning Do not use abrasive products as these are liable to take the sheen off shiny parts Hopper Wash the hopper once it has been removed from the appliance unscrewing the relevant fastening screw using neutral soap and water rinse abundantly with lukewarm water and dry thoroughly It is advisable to clean the hopper periodically Once the hopper has been cleaned it must be attached to the upper grinding blade holder using the relevant screw Grinding system Remove the safety screw which prevents the adjustment disk from being removed Unscrew the adjustment disk by turning it clockwise Having removed the upper grinding blade holder clean the grinding blades threads and the entire grinding system thoroughly using a clean brush and cloth Having refitted the upper grinding blade holder in the relevant slot screw the adju stment disk back on put the self locking screw back in whichever of the two holes on the disk enables the best adjustment and having refitted the hopper and secu red adjust the grinding as required Doser Coffee grinder version Having discharged the ground coffee clean the doser s star unit with a clean brush expelling the material removed by pulling the doser lever Use a dry cloth to thoroughly clean the
10. lug adapters for multiple sockets or makeshift connections e In EEC member countries the regulation in force calls for the external equipoten tial terminal on the outer part of the appliance s base plate to be connected to a equipotential node if the installation is to be correct The motor must rotate clockwise If the rotation of three phase motors is to be inverted by inverting the two power supply wires inside the plug this must be carried out by skilled personnel THE HOPPER MUST BE FASTENED TO THE APPLIANCE S GRINDING SYSTEM BY MEANS OF THE RELEVANT SCREW which must be inserted in the threaded hole located on the upper grinding blade holder and in the hole on the neck of the hopper 8 OPERATION OF THE APPLIANCE PRELIMINARIES Make sure the hopper is positioned correctly on the appliance and is fastened to the upper grinding blade sain holder by means of the relevant screw Close the locking slide and fill the hopper with coffee beans Open the locking slide so that the beans are allowed to drop into the grinding system SWITCHING THE APPLIANCE ON AND OFF GRINDER DOSERS WITH MANUAL SWITCH AND COFFEE GRINDERS The on off switch is used to turn the appliance both on and off To switch on set the switch to I To switch off set the switch to O GRINDER DOSERS WITH TIME SWITCH In order to switch the appliance on turn the timer knob clockwise The appliance switches off automatically In order to switch it off manu
11. our appliances is included within the limits stated in U S regu lation 29 CFR 1910 95 Occupatinal Health and Environment Control Occupational noise exposure for eight hours continuosly in a day Said noise level has been determined on identical news appliances 13 MAINTENANCE It is essential to check the state of the supply cable and plug periodically IN THE EVENT THE SUPPLY CABLE OR PLUG ARE DAMAGED CALL IN SKIL LED TECHNICAL PERSONNEL TO REPLACE THEM THIS TO PREVENT ANY RISK IN C CERTIFIED APPLIANCES A SPECIAL TOOL IS REQUIRED TO OPEN THE BASE PLATE TO GET AT THE CABLE lt is recommended to use original spare parts only In order to assure the lasting efficiency of the appliance skilled technical person nel must be called in to perform periodical maintenance including detailed checks of the state of those components subject to wear The state of the grinding blades must be checked periodically Keeping the grinding blades in an excellent state assures high quality grinding resulting in greater pro ductivity and limited overheating When using coffee blends of average hardness it is advisable to replace the grin ding blades approximately every 400 kg for the Super Jolly model 300 kg for the Mini model 350 kg fot the Lux model 14 CLEANING THE APPLIANCE DISCONNECT THE APPLIANCE S POWER SUPPLY BY UNPLUGGING IT BEFORE CLEANING THE APPLIANCE MUST NOT BE CLEANED USING WATER JETS Do not install the
12. stment and must not be removed by the user under any circumstances e COFFEE OUTLET GUARD The coffee outlet guard must always be fixed to the doser using the relevant screws wich must never be removed by the user The removal of the coffee outlet guard can be done by skilled technical person nel only after disconnecting the appliance from the power supply by unplugging Before reconnecting the appliance to the power supply fix the safety device to the doser by the relevant screws 11 WARNINGS REGARDING SAFETY This electrical appliance must be used in conformity with the rules in force gover ning safe operation e WHEN OPERATING THE APPLIANCE BEWARE OF THE MOVING MECHA NICAL PARTS IN THE AREA OF THE GRINDING BLADES AND OF THE GROUND COFFEE OUTLET BEFORE REMOVING THE HOPPER FROM THE GRINDING SYSTEM DISCONNECT THE POWER SUPPLY AVOID REMOVING FOREIGN BODIES FROM THE GRINDING SYSTEM OR HOPPER WITHOUT FIRST UNPLUGGING THE APPLIANCE FROM THE MAINS Take care as the grinding blades may continue rotating for a short while even after the appliance is switched off THE USER IS NOT AUTHORIZED TO REMOVE SCREWS OR ANY PARTS SCREWED ONTO THE APPLIANCE e In the event the appliance is not working properly or is faulty contact skilled technical personnel and do not attempt to make repairs yourself e BEFORE PERFORMING ANY WORK ON THE APPLIANCE INCLUDING CLEANING AND OR MAINTENANCE DISCONNECT IT FROM THE POWER SUPPLY BY UNPLUGGING T
13. uch as the wei ght of the portions the compacting the espresso machine settings and the clea ning of the filters COFFEE DOSE ADJUSTMENT grinder doser version In order to adjust the size of the portion dispensed the small knob located in the centre of the ground coffee storage container must be turned while holding still the star shaped dosing unit COFFEE DOSE ADJUSTMENT COLLECTING THE DOSE INCREASE THE DOSE turn anticlockwise REDUCE THE DOSE turn clockwise By turning the small knob clockwise the portion is reduced Turning it anti clockwise results in an increase In order to collect the portions of ground coffee dispensed insert the coffee machine s filter holder all the way onto the fork shaped support under the ground coffee outlet In order to release a portion of ground coffee the doser lever must be pulled all the way and allowed to return on its own Pull twice in a row for a double portion In manual coffee grinder dosers and those with time switches in order to assure the portions are regular check every now and again to make sure the amount of coffee ground to be found in the doser is sufficient to cover the feeding star unit To centre the coffee drop into the filter holder it is possible to carry out a sideways adjustment of the support fork located under the dispenser by slightly loosening the fixing screws and then tightening them again after having moved the fork into the new position
Download Pdf Manuals
Related Search