VIEWPORT Monitors - Boland Communications
Contents
1. Operation Monitor Back Side Input Connector Well Power Recessed wiring location for all cables Place the plug from the world wide AC power supply included into the DC 12V connector Input power to the monitor from any other source must be within the DC Voltage range marked on the monitor label or backside markings Some monitors will accept 9 36 VDC Input BNCs S Video and VGA Connectors Attach the video cord s from cameras VCRs PC or other sources to the BNC Y C S Video or VGA connectors When two BNCs are present connect a source to either A second cable will allow further connection to another display or device The internal 75 termination is automatically switched off Optional Audio and Speaker s Audio inputs are high impedance Some monitors may have a jack to feed external speakers Threaded Mounting Sockets The corner threaded sockets are for mounting the monitor You may mount monitors in any orientation The screw must not insert deeper than 1 2 12 mm The threads are 10 32 See page 4 above regarding VESA mounting Y 20 Threaded Mounting Socket For flexibility in mounting you may use this bottom side threaded socket for locating the monitor on a tripod like an SLR or video camera or other CCTV mounting arm or device Do not insert the screw head deeper than 3 8 8 mm ViEWwPortT Manual d series OSD Menu Functions Note Software updates may enhance these menu offer2. cd m Operation In addition to the standard button controls of a normal monitor a knob is added to the front panel to control the brightness of the internal lamps With a range of nearly 100 1 the brightness can be adjusted to outdoor daylight conditions down to minimum for night use Power consumption is much reduced at less than the full setting The brightness can be set to any value without having to change electronic video adjustments via the menu system Brightness in the menu means the video adjustment of the glow inthe blackareas of the picture Contrast is used to set the whiteness of the lightest areas of the picture Note DayBrite models usually have a fan switch located in the well area Use the fan Ise at noon in the sun you will need the HI setting Without sunshine or full CW low or off may be sufficient to keep the cabinet cool ViEWPorT Manual d series A Maintenance A VIEWPorT display requires no regular periodic maintenance e Cleaning The standard cabinet finish is semi gloss black paint over aircraft aluminum or the aluminum cabinet itself is mil spec black dye anodized e Factory Service After about fifty thousand hours of service as long as 10 years even if used often depending on the Boland model it may be possible to notice the screen brightness start to fall to half or less of its original level Or the internal fluorescent lamps may not come on at all or stay on properl
3. installed Input Select Menu Push Menu button twice within 1 2 second to directly access this menu Note only installed inputs for this monitor model are displayed and only if enabled in the Setup Menu under AUTO SOURCE SEEK HD SD SDI 1 HD SD SDI 2 VGA DVI HD Component Composite 1 Composite 2 S Video PIP Source gt Inserted video for both Picture in Picture and Picture by Picture PoP modes OFF HD SD SDI 1 HD SD SDI 2 VGA DVI HD Component Composite 1 Composite 2 S Video XS Utilities Menu Setup gt Auto Picture Setup Auto adjust the image position phase and size Auto Color Gain Auto Color Calibration RGB white levels Wide Screen Mode detection Choose to recognize the VGA mode as a normal or wide screen input Normal 4 3 1280x768 Widescreen 1366x768 Widescreen 16 9 Manual Clock um Adjust the image horizontal size Manual Phase um Adjust image quality fine tune the data sampling position Auto Source Seek gt Setup gt Choose to display and auto detect signals for these inputs HD SD SDI 1 az HD SD SDI 2 VGA DVI HD Component Composite 1 Composite 2 S Video Note only the names set to ON will display on the Input Select Menu ON The monitor will Seek a new input if a signal is lost or missing OFF Seek function is disabled inputs will change only by manual choice De interlacing Mode gt AFM eam Auto Film Mode 3 2 pull down complian
4. Communications Boland warrants the VIEWPORT LCD Monitors and their accessories are provided to be free from defects under normal use Parts are covered for a period of two 2 years and Labor is covered for one 1 year from the date of delivery to you The Pro Series of monitors carries a separate term of one 1 year Parts and Labor warranty All monitors with a serial number less than 009001 manufactured before April 2005 carry their original one year warranty In the event of a repair under this warranty Boland s sole obligation is to replace or repair at Boland s option any Product free of charge Any replaced parts shall become Boland s property Warranty claims must be made during the warranty period and within seven 7 days of the observation of the defect accompanied by any necessary evidence satisfactory to Boland Prior to returning any Product to Boland you must obtain a Return Authorization RA Tracking Number and receive shipping instructions from Boland Shipments without an RA are subject to refusal at Boland dock All Products returned to Boland contain glass and shall be adequately packed 200 Ib corrugated carton and 2 foam on all six sides of product minimum and shipped with freight and insurance sender prepaid or the warranty coverage will be void and are subject to return unrepaired Boland will return all repaired units in double carton and cushion packaging via pre paid UPS Ground Insured Customer may provid
5. QO BOLAND COMMUNICATIONS ViewPort Monitors Color Active Matrix LCD Video VGA Combi Screens STANDARD DEFINITION MODELS NTSC PAL SECAM amp NTSC4 43 PAL M Full PC Scaling from EGA to WUXGA 4 3 16 9 Variable Aspect Ratios H amp V Scan Reverse Picture in Picture User Manual for models 8 4 Models d084c xd084b d084cDB 17 0 Models d170c d170cDB 10 4 Models d104h xd104d 19 0 Models d190c 12 1 Models d121e d121eDB 20 1 Model d201c 15 0 Models d150c d151cDB amp x1 x2 Rackmounted versions of above Lake Forest CA 92630 800 918 9090 949 465 9911 Fax 949 465 9944 www bolandcom com 9 VIEWPORT d series 071007 description overview The BOLAND Combi VIEWPorrs are high performance LCD video displays for computer and motion video display The display quality is excellent for both natural and graphic video The moni Description tors come with integral non glare glass screens and are part of the compliment of 4 0 up to 37 ViEwPorr family of LCD Video and Computer monitors All offer the size brightness and clarity necessary for extended daily use standard features included in all models gt SR Scan Reverse Picture may be mirror imaged Horz Vert or both for prompting or other effects Image may also be rotated 90 AR Aspect Ratio Display may be switched between 4 3 16 9 or adjustable user settings 1 85 etc UDS Up Down AutoScaling A built in scaler automatic
6. ally accepts any computer resolution from less than CGA up to UXGA for full screens gt PiP Picture in Picture Main image or window image may each be any two of the three video and computer inputs Moveable sizeable window gt CF Comb Filter Intelligent adaptive NTSC Y C filter provides full resolution e customer support Boland provides a full range of support from sales through installation and application of our products We are here to help Our office hours are extended in the Pacific time zone GMT 8 in winter 7 summer To reach us without artifacts AS Automatic TV Standards Worldwide NTSC PAL SECAM NTSC4 43 PALM all autodetected gt US Under Scan Video mode picture size fully variable from overscan to normal to underscan gt PZ Picture Zoom Magnify images up to 1000 View window is pan tilt adjustable gt CT Color Temperature screen temperature fully variable in PC and Video with four presets gt SDI Serial Digital Interfaces Options Input 270 Mb or 1 45 Gb digital video for standard or HDTV Auto detected Reclock regen output s BOLAND COMMUNICATIONS 949 465 9911 or 800 918 9090 949 465 9944 fax Lake Forest CA 92630 or techsupport bolandcom com ViEWwPortT Manual d series 2 installation e supplied items Supplied with your LCD Monitor is a desk top universal 100 250 VAC 50 60 Hz AC to 12 volt DC regulated power supply power and VGA cords a
7. ce TNR Memm ae Temporal Noise Reduction MaDi mam Motion Adaptive De interlacing LADI mam Low Angle De interlacing Auto Power gt Automatic monitor power off for missing signal automatic power on ON Enable soft power off in absence of an input signal OFF Disable soft power function Video Standard SD gt Auto NTSC NTSC 4 43 PAL PAL M SECAM Image Orientation gt Normal Horizontal flip Vertical flip Rotate OSD gt On Screen Display menu system OSD position H POS um move the OSD menu box horizontally V POS um move the OSD menu image vertically OSD Timeout OSD menu timeout period 5 to 60 seconds Note select 0 for continuous display of OSD menu Transparency Sets OSD to Transparent or Opaque background Color Temperature gt Note settings are remembered for each input source name 5000K gt each temperature has an individual RGB submenu as shown below 6500K gt Red a 0 100 8000K gt Green OH 0 100 9300K gt Blue a 0 100 Default Restore initial set of factory values ViEWwPortT Manual d series Utilities Menu continued Hot Keys gt Sets operation of button pairs to directly access functions when OSD menu is not visible Use up down arrow keys to highlight desired function and use gt key to select Hot Key 1 Volume Brightness Contrast Inout Aspect PIP Size PIP Swap Image Orientation Hot Key 2 Volume Brightnes
8. e own shipping number or arrange upgrade for faster return Except as stated above there is NO OTHER WARRANTY REPRESENTATION OR CONDITION REGARDING BOLAND S PRODUCTS SERVICES OR PERFORMANCE EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Boland is not responsible for any delays beyond its control and where possible will advise of any such delays Boland s entire liability for damages to you or any other party for any cause whatsoever whether in contract or in tort including negligence shall not exceed the price you paid for the unit of Product that is the subject matter of the dispute In no event will Boland be liable for any damages caused by your failure to perform your obligations or for any loss of data profits savings or any other consequential and incidental damages even if Boland has been advised of the possibility of damages or for any claims by you based on any third party claim Warranty
9. ings ViEWPorT Manual d series Picture Menu Note gt indicates a sub menu use gt button to enter Brightness Oo Q brightness level picture blacks level 100 steps Contrast Oo g contrast level picture whites level 100 steps Saturation Oo g colors saturation 100 steps Hue oOo g hue of colors flesh tones 100 steps Sharpness Oo D sharpness of picture 30 steps Volumet o g volume of sound connected to monitor 100 steps NOTE Monitor factory calibration settings are 50 50 50 0 0 Aspect Size gt Fill Screen Enable full screen expansion for lower resolution Fill to Aspect Ratio Enable fill screen expansion for lower resolution image according to aspect ratio height or width 4 3 sizes image to 4 3 format 16 9 sizes image to 16 9 format 16 10 sizes image to 16 10 format 2 35 1 sizes image to 2 35 1 ratio format 2 1 sizes image to 2 1 ratio format 11 displays the image in exact image resolution on the screen without image expansion reduction pixel for pixel mode Custom Sizing Normal Underscan Custom H Size M V Size ME H Pan Fp L Blue Only gt isan ON OFF Turns off the red and green channels for calibration of display using test signal SMPTE color bars or equivalent NOTE This menu item not visible on monitors with a separate RGB only Hot Key Not displayed for all input signal types appears only as appropriate t Displays only if Audio Option Opt 29 is factory
10. ion cords on the rear In the corners on the backside of monitors are 10 32 threaded inserts for mounting screws Use screws that don t penetrate the cabinet more than 1 2 Also on the backside of many models are 75 or 100 mm VESA pattern holes These holes may accept no 6 8 10 M3 3 5 or 4 screws depending on a model s size and weight The VESA holes are typically used for wall mounts and desk stands e power and video connections ViEWwPorT LCD monitors connect like CRT type monitors The connections are video and power Power Connection 12 Volts DC Insert the barrel or XLR plug from the desk top power supply into the jack on the back of the panel The AC side of the power supply will accept 100 240 VAC 50 60 Hz Some monitors have Installation for use as connected to all normal baseband video systems The C component of the Y C signal is 0 7 Vpp nominal The built in scaler very cleanly displays PC images from CGA 320 x 480 to WUXGA 1920 x 1200 resolutions Boland models for high resolutions formats like HDTV are available Also up to 15 a 20 UNC threaded socket is on the bottom side not for vehicle use The LCD monitors dissipate only a few watts see specifications so no special cooling or ventilation is usually required except with DB models The mounting location may usually be enclosed But avoid any mounting situations with appliance environmental or solar heat sources that
11. may cause the monitor s operating location to exceed 122 F 50 C an optional 9 to 36 VDC feature built in Video Connections Most VrewPorr monitors have BNC connectors for composite 4 pin for S Video and one VGA input video source per screen most screens have auto terminating loop thru 75 BNCs Computer Connections next page ViEWwPortT Manual d series e computer connections The VGA connection may be made with the supplied cord plugging a cord into the back of the monitor and into the back of the computer Supply the monitor with a CGA 820 x 480 up to a WUXGA 1920 x 1200 signal A built in processor will adjust the image automatically to fit the screen Installation Video In Loop Thru Power In S Video In Auto Termination YGA In Option 1 Gnd 4 Yolts l Connector Well typical of 10 4 to 37 Monitors For DayBrite Monitors see page 10 for operation of the fan switch located here 3 Operation Your ViEwPorT Monitor s On Screen menu provides for normal operational adjustments These user adjustments are stored memorized separately for VGA Composite and Y C S Video and separately for both NTSC and PAL modes Push the menu button to bring up the menu and to step down through the icons Starting on the subsequent pages are all the menu choices and a description of each item ViEWPorT Manual d series For normal operation set the Brightness to just be able to see the blackest por
12. nd this instruction manual Outside the US a e handling A ViEWPorT display is rugged As a precaution though please consider the following general characteristics of AMTFT LCDs These are not defects or malfunctions Please handle the panel with care Since the panel is made of glass sharp blows to the screen failure after dropping onto a hard surface etc are not covered by the warranty High voltages are present inside the cabinet for the fluorescent lighting There are no fuses or other user serviceable parts inside Do not remove any screws or disassemble the cabinet to stay safe and to retain the Warranty Use only factory specified power supplies for powering the panel A wet condensing atmosphere dew or fog should be avoided If you require routine operation in these conditions please consult the factory optional cabinets are available Note the normal operating and storage temperatures in the specifications Do not place the unit in the sun as the black cabinet can absorb a considerable amount of heat Extreme temperatures just as uncomfortable for people will cause degraded performance or permanent LCD ViEWPorT Manual d series Installation local power cord may be needed Available options may include SDI High Brightness 1850 nts Remote Controls and VESA Rack Wall Mounts and Desk Stands damage Extended temperature models are available Please also take care to avoid electr
13. ostatic discharges When a panel is not installed place it in its packing material or place it face down on a smooth table After several thousand hours of operation the special internal fluorescent lamps will eventually taper in their brightness Please consult the factory for replacement Over long periods of time some changes in luminance uniformity or small dots may become visible depending on image content Avoid fixed video patterns for extended periods of time Some image retention may temporarily occur If possible use an interesting screen saver or black Please handle cables and connectors with care Please replace worn cables with standard locally available parts see power supply substitution caution Note that although most Boland screens are glass they are still somewhat sens itive to scratching Please clean with a soft cloth slightly dampened not dripping with water or if necessary Windex or 409 type cleaners e system requirements VIEWPORT monitors operate on DC power and display PC video with a 15 pin VGA connector composite video signal with BNC or S Video with a 4 pin mini DIN or S connectors Monitors will display a composite or S Video from a 525 or 625 standard video signal at a nominal 1 0 Vpp when properly 75 terminated where source video is 2 0 Vpp unterminated and are e physical mounting When mounting the panel on a flat surface allow clearance for any connect
14. s Contrast Input Aspect PIP Size PIP Swap Image Orientation PIP PiP Size Off Small Medium Large PBP side by side Picture by Picture Note Four possible input groups that can be mixed for PIP Main and PIP must be from two different groups Not all inputs are on all mons a VGA HD component b DVI c HD SDI d Composite S Video SD component Those input group combinations not allowed are greyed out in the menu PiP Position Use four arrow v4 gt lt keys to move the PiP window on the screen PIP Swap Select to swap the pictures between the main window and PiP window Monochrome Mode Color picture is converted to monochrome Y and displayed in one primary Red Monochrome mono picture is displayed in shades of red Green Monochrome mono picture is displayed in shades of green Blue Monochrome mono picture is displayed in shades of blue Reset to Factory Defaults Use gt key to initiate a reset to return all monitor settings to factory original CAUTION All previous user menu choices are lost Not displayed for all input signal types appears only as appropriate Displays in VGA mode only j Displays in VGA and HD Component modes only ViEwPort Manual d series High Bright Monitors Description The High Brite Option is a factory installed accessory for an LCD video monitor to boost its brightness to full daylight readability The 12 and 15 displays are specified at about 1800 nts
15. tions of the video image then Contrast to bring the whitest areas of an image to just less than wash out Then set Color and Tint NTSC for pleasing flesh tones Controls and Connections 1 Monitor Front Side Power On Off When power is applied the monitor will come on This button then turns the monitor on and off menu Menu On Off This button is used to bring up the controls menu Upon Exit the menu clears from the screen saving the new settings chosen or wait 10 seconds Y Select Down Contrast Advance down the menu list with this button Without pushing the menu button first this button is Direct Access 2 to reduce Contrast lower whites level A Select Up Contrast This is used to move up through the menu list Without pushing the menu button first this button is Direct Access 2 to increase Contrast raise whites level lt Decrement PC Use to reduce the amount of the highlighted item For some items this selects No or Off Without pushing the menu button first this button is Direct Access 1 to select the next active available video source in the list gt Increment Enter Video Pushing this button increases the amount of the chosen item For some types of items the button will chose Yes or Accept Without pushing the menu button first this button is Direct Access 1 to select the next active available video source input in the list 1
16. y especially when Maintenance The front screens are non glare glass A damp not dripping cleaning cloth with a small amount of spray cleaner such as 409 or Windex may be used to remove dust or fingerprints You will not want to have enough moisture on the outside of the cabinet that liquid would run inside through the cracks the temperature is cold In these cases the full brightness may be restored by replacing the special type of internal fluorescent lamps not user serviceable these require extreme care in avery clean environment Please contact BOLAND COMMUNICATIONS for factory replacement e Warranty Note opening the cabinet voids the warranty VrewPoRrT Video Displays are warranted for one year against defects in materials or workmanship see the Warranty A greement page 15 Consequential damages are not covered Units requiring attention will ViEWPorT Manual d series need to be returned to the factory for correction Telephone for a tracking RA number before shipping Units will be returned UPS Ground pre paid Warranty correction is at best an inconvenience so every reasonable effort will be made by BOLAND to smooth the process 10 VIEWPort warranty 05 18 05 BOLAND COMMUNICATIONS WARRANTY AGREEMENT All products including hardware software firmware and documentation are subject to the terms below Opening the monitor cabinet in any manner for any purpose voids the warranty Boland
Download Pdf Manuals
Related Search