the 510 User Manual
Contents
1. the 510 included electromagnetic damage can cause malfunctioning and corrupt or destroy data Since this is an ever present danger thorough care should be taken to minimize the risk of damage Please observe the following safety tips and precautions to ensure hazard free use of the 510 A Cleaning About power Warning Since power consumption of this unit is fairly high we recommend the use of an AC adapter whenever possible When powering the unit from a battery use only an alkaline type AC adapter operation Be sure to use only an AC adapter which supplies 9 V DC 300 mA and is equipped with a center minus plug Zoom AD 0006 The use of an adapter other than the specified type may damage the unit and pose a safety hazard Connect the AC adapter only to an AC outlet that supplies the rated voltage required by the adapter When disconnecting the AC adapter from the AC outlet always grasp the adapter itself and do not pull the cable Tf the unit is not to be used for a long time disconnect the AC adapter from the outlet Battery operation e Use only a9 V alkaline battery 6LR61 The 510 cannot be used for recharging Pay close attention to the labelling of the battery to make sure you choose the correct type If the 510 is not to be used for an extended period of time remove the battery from the unit If battery leakage has occurred wipe the battery compartment and the battery terminals c2. factory these are programmed with recommended A group of the settings for a certain effect type is called a PATCH The 510 comes with 24 preset settings The user can Edit and Store any patch and also restore the factory settings patches which can be changed edited by the user PATCH PATCH NAME PRE DRIVE MAIN DRIVE COMMENT Al Multi Drive RHYTHM DISTORTION Dual distortion sound for all styles A2 Metallic OFF METAL Metal sound for low note riff z BANK A3 The Over Drive COMP OVER DRIVE Standard overdrive with comp The 510 calls up patches in sets of four called a bank AG _FUZ2Y OER ste Contemporary fuzz sound Power DIST COMP DISTORTION Stacking amp simulation Feelin Wah AUTO WAH OVER DRIVE Wah controlled by picking Bass Plus OCTAVE OVER DRIVE Play Superstition BAN K E Heavy Bottom BOOSTER DISTORTION Heavy drive with bottom tone GRUNGE LIGHT OD GRUNGE High gained grunge drive BANK d PATCH 1 ord drivin turbe PATCH 1 PATCH 2 The Crunch BOOSTER DISTORTION Crunch sound good for rock amp roll Vintage RHYTHM BLUES OD Vintage drive sound good for blues BANK b Dynamic OD DYNAMIC OD OVER DRIVE Touch sensitive drive BANK A PATCH 1 PATCH 2 PATCH 3 PATCH 4 OD Line AMP SIM LIGHT OD OVER DRIVE Overdrive sound for line connection Small Box AMP SIM BOOSTER BLUES OD Small amp simulation for line connection PATCH 1 PATCH 2 PATCH 3 PATCH 4 Old Fashioned AMP SIM COMP LEAD Old amp simulation for line connection PATCH 2 PATCH 3 PATCH 4 COMP DRI
3. mode to the Play mode Ne The keys serve for setting the tuner reference pitch calibration e Setting of bank hold function When the EDIT key is held down for at least 1 second in Play mode the bank hold i function is turned on or off For details see 9 Patch Switching Application Bank PATCH UP right DOWN left pedals e Play mode Hold ON A The pedals serve for patch switching Pressing both pedals simultaneously activates the Bypass Tuner mode Edit mode The pedals serve for selecting effect parameters Pressing both pedals simultaneously turns the currently selected effect module on or off R ear P a nel Bypass Tuner mode C Pressing either pedal cancels the Bypass Tuner mode to return to Play mode J The keys serve for changing the effect parameter ae INPUT jack Instrument input When the unit is powered by the battery this jack also functions as the power on off S a switch The 510 is powered on by plugging a shielded cable into this jack When the CONTROL IN jack C unit is not in use the cable should be disconnected to prevent battery drain The optional foot switch FS01 or expression pedal FPO1 can be connected here for external control of the 510 DIRECT OUT j N e When the foot switch FS01 is connected jack sauce Bi A Supplies the signal from the INPUT jack without any processing INPUT DIRECT OUT The PRE DRIVE effect module is switched on and off with the foot
4. the The bypass function is invoked by pressing the left and right B d Press both patch pedals simultaneously ypass mode pedals together To cancel the Bypass Tuner mode just press one of the patch pedals Currently selected I patch is displayed A l m bP Press Release immediately Tuning function only when the tuning function is ON To cancel the Bypass mode simply press one of the patch pedals The unit then reverts to the previously selected patch Tuner mode The 510 is initially set so that the auto chromatic tuning function for the guitar activates automatically when the Bypass mode is invoked In Bypass mode pick an open string to be tuned The closest note will be shown on the display Input signal standby condition Regular tuning e odo c Pet vt JO Eee Fato CO a fansin D L Se o Dot C Regular tuning _ Regular tuning 7 ES 6th string T Em _ TI 5 Mi E E 1st string So G I 3rd string S Lait Ait H a Regular tuning Regular tuning 6 Re D lansing E Fa Ff Esot O Si B H oasng Poe When the tuning function is active the parameter cursor LEDs serve as tuning meter designed to enhance tuning precision during fine adjustments i eon AN nanny Turning tuning function off If you do not want to activate the tuning function in Bypass mode press the STORE and EDIT keys simultaneously for P tchistoohign Correctly tuned Pitch is too low more than one se
5. 70005 7 OSER Operation Manual Thank you for selecting the ZOOM 510 hereafter simply called the 510 Please take the time to read this manual carefully so you can get the most out of your 510 and ensure optimum performance and reliability Retain this manual for future reference ZOOM CORPORATION NOAH Bldg 2 10 2 Miyanishi cho Fuchu shi Tokyo 183 J apan PHONE 0423 69 7116 FAX 0423 69 7115 Printed in Japan 510 5000 ZE CATCH US IF YOU CAN EE Major Features Dedicated distortion unit with two on board distortion modules PRE DRIVE and MAIN DRIVE Parallel or serial connection of distortion modules allows the creation of variations that are difficult to achieve with conventional multi effect devices such as adding light distortion after strong distortion The result is a wide variety of overdrive and distortion sounds Total of 16 effects eight effect types per distortion module can be combined Besides distortion effects PRE DRIVE also contains compressor pedal wah auto wah octaver and other versatile effects You can switch between 24 patches to store diverse settings based on your preference Integrated auto chromatic tuner for guitar You can tune your instrument easily anywhere any time You can also leave the tuning function disabled all the time Mixing balance of PRE DRIVE and MAIN DRIVE can be varied according to picking intensity using the auto parallel connection feature This provides a wide expr
6. VE Mix COMP OVER DRIVE Pd Use FPO1 to add overdrive PATCH 3 PATCH 4 WAH DIST AUTO WAH BLUES OD Pa Can be changed to overdrive by FPO1 PATCH 4 In the PRE DRIVE MAIN DRIVE column indicates serial connection and parallel connection ZNR ZOOM NOISE REDUCUTION should be adjusted for the guitar you use Rhythm amp Blues RHYTHM OVER DRIVE Crunchy overdrive good for R amp B BANK F Violent Wah PEDAL WAH FAT DRIVE Half opened pedal wah sound Hard Drive COMP OVER DRIVE Hard drivin turbo overdrive BANK C PATCH 1 PATCH 2 PATCH 3 Crunch Wah AUTO WAH 7 OVER DRIVE Play hard to add wah effect PATCH 1 PATCH 2 PATCH 3 PATCH 4 DIST Line AMP SIM LIGHT OD FAT DRIVE Distortion sound for line connection Pedal Boost BOOSTER LEAD Pd Main drive can be controlled by using FP01 Metal Octave OCTAVE METAL Metallic sound play single note The OCTAVE effect is not suitable for chord input To prevent wrong operation pick only precise single notes 5 Configuration of Effects The patches of the 510 are created using the PRE DRIVE MAIN DRIVE HIGH LOW sound Effect parameters can be adjusted just as you can turn the knobs on a single compact equalizer and ZNR AMP Zoom Noise Reduction Amp Simulator modules You can imagine effect device A patch is a combination of two effects from the modules each with their effect a module as a box containing various effect settings pa
7. Y type stereo shielded cable or a pair of stereo headphones If the volume level mA with a center minus plug configuration The 510 is powered on by plugging is low when using headphones use headphones with low impedance 32 ohms or an AC adapter into this jack less j DIRECT OUT DETECTOR IN J gt Selecting Patches Bank switching Banks A b C d E F are available PATCH PATCH DOWN UF PATCH 1 E PATCH 2 Patch switching PATCH 3 24 patches are available PATCH 4 PATCH 1 PATCH 2 The 24 patches can be easily selected by PATCH 3 pressing the patch pedals The right patch A PATCH 4 pedal switches to the next patch and the BANK UP left patch pedal switches to the previous patch PATCH 1 In the initial condition the 510 is set up CATCH E so that the patch pedals select patches L PATCH 3 continuously but you can also set up the PATCH 4 unit so that patches are switched only within a certain bank of four patches For details see section 9 Patch Switching PATCH 1 Application Bank Hold ON BANK DOWN PATCH 2 v PATCH 3 PATCH 4 Banks are selected with the VALUE keys Press the VALUE key to select the next bank and the VALUE key to select BANK b the previous bank PATCH 1 For example to switch fro
8. ad functions is called all initialize The Recall mode is separate from the Play mode and Edit mode You cannot switch directly to Recall mode from these modes The Recall mode can only be activated by turning the unit on in a special way as described below Turn the unit off by disconnecting the AC adapter or the guitar input cable Keep the STORE key depressed and turn the unit on The indication AL flashes on the display To perform all initialize press the STORE key once more in this condition The flashing rate increases and the initialization procedure is carried out When it is completed the unit automatically enters the Play mode When wishing to recall only a particular patch select the patch number in step 3 using the same procedure as for normal patch selection When the desired patch has been selected press the STORE key The flashing rate increases and the contents of the selected patch are recalled Recalling of individual patches can be carried out continuously When you wish to terminate the process press the EDIT key The unit then returns to the Play mode Turning the unit off also terminates the recall condition 16 BS etait ei Effects 19 effects e PRE DRIVE Booster Rhythm Light Overdrive Dynamic Overdrive Compressor Auto Wah Pedal Wah Octave MAIN DRIVE Overdrive Blues Overdrive Fat Drive Distortion Fuzz Grunge Lead Metal Equalizer e ZNR Zoom Noise Reduction Amp Simulat
9. arefully to remove all remnants of battery fluid While using the unit the battery compartment cover should be closed Environment Avoid using your 510 in environments where it will be exposed to Extreme temperature High humidity or moisture Excessive dust or sand sive vibration or shock Handling Caution e The 510 is a precision instrument Except for the foot switches do not push other parts with your feet or subject them to strong force Take care that no foreign objects coins or pins etc or liquids enter the unit Be sure to turn the power to all equipment off before making connections Before moving the unit turn the power off and disconnect all cables and the AC adapter Alterations A Never open the case of the 510 or attempt to modify the product in any way since this can result in damage to the unit Caution Use a soft dry cloth to clean the 510 If necessary slightly moisten the cloth Do not use abrasive cleanser wax or solvents such as paint thinner or cleaning alcohol since these may dull the finish or damage the surface Connecting cables and input and output jacks You should always turn off the power to the 510 and all other equipment before connecting or disconnecting any cables Also make sure to disconnect all cables and the AC adapter before moving the 510 3 What Are Banks and Patches 4 Be Re e PATCH The 510 has memory capacity for 24 patches At the
10. cond in Play mode The tuning function will be turned off and this setting will be stored even when the power is turned off When you turn the function off the display will show tunEr oFF tuning function off To turn the tuning function on press the same keys simultaneously again The display will show tunEr on tuning function on NOTE Please note that the tuning function may not operate properly if other effect modules between the guitar and the 510 are on KJ Patch Switching Application Bank Hold ON In the initial setting the patch pedal switches all patches in order regardless of the bank divisions Bank Hold ON Keeping the EDIT key depressed for at least 1 second activates Bank Hold To cancel Bank Hold press the EDIT key again for 1 second The bank hold function limits switching to the four patches within a bank When this function is activated the patch pedals switch in order between the patches in the current bank only Bank switching Banks A b C d E F can be switched To activate this function hold the EDIT key down for at least 1 second in Play mode The BANK HOLD indicator will light To turn the function off again hold the EDIT key down Patch switching for at least 1 second The 4 patches within bank can be switched BANK HOLD indicator will go off Banks can be switched using the VALUE keys Bank patch switching when Bank Hold is o
11. e parameter you wish to change Use the VALUE keys to change the setting of the parameter For details on parameters please refer to section 12 Effect Parameters 1 BOOSTER 2 RHYTHM 3 LIGHT OD 4 DYNAMIC OD Creates a Light distortion Light overdrive Dynamic overdrive clean sound suitable for Light overdrive Dynamic overdrive effect with prominent rhythm guitar with changing midrange characteristics depending on picking intensity selected the Edit mode is terminated and the 510 reverts to the Play mode PATCH UP moves the blinking parameter cursor one step up and PATCH DOWN moves it one When the PATCH DOWN pedal is pressed while the TUNER indicator Parameter 9 SERIAL PARA is flashing the 510 stays in Edit mode and parameter 1 is selected 2 Use the VALUE keys to adjust the parameter to Play mode 3 While the TUNER indicator Parameter 9 is flashing press the EDIT key to return 5 COMP 6 AUTO WAH 7 PEDAL WAH 8 OCTAVE Compressor Conventional compressor effect Auto wah with changing characteristics depending on picking intensity Pedal wah for use with optional expression pedal FP01 The center frequency that is being emphasized goes up and down depending on the pedal action Natural sounding octaver creating a sound one octave lower For use with single notes only Setting range 7 increases the setting by 1 e
12. er The master level is adjusted in Play mode Hold the VALUE keys down simultaneously for at least 1 second The current master level will be displayed for 1 second To switch the ZNR AMP module on and off In Edit mode while parameter 7 is selected press the PATCH UP and DOWN pedals together to turn the ZNR AMP module off The display indication for parameter 7 becomes oF While the level is being displayed use the VALUE keys to change it The setting range is 0 50 Default value 40 The unit does not store the setting for the master level Each time the power is turned on it has to be set again 13 Boe eal te If you have edited altered a patch and turn the 510 off without storing the patch the patch will revert to its old setting To store an edited patch use the following simple procedure Storing can be carried out in both Play mode and Edit mode After you have edited the patch press the STORE key If the unit is currently in Play mode release the key before 1 second has elapsed otherwise the Direct Load function will be activated The display starts to flash This condition is called the store standby condition If you wish you can abandon the store procedure at this point by pressing the EDIT key If you press the STORE key once more the contents of the patch are updated You can also change the patch number before storing so that the edited patch will be stored in a different number In this case
13. ession range for solo play Optional expression pedal FPO1 can be used to control pedal wah MAIN DRIVE gain mixing balance for parallel connection and other parameters Optional foot switch FS01 allows switching PRE DRIVE on and off during a performance Dual power supply design allows the unit to be powered from a 9V alkaline battery 6LR61 or an AC adapter 2 Safety Precautions USAGE AND SAFETY PRECAUTIONS In this manual symbols are used to highlight warnings and cautions for you to read so that accidents can be prevented The meanings of these symbols are as follows A Warning A Caution Usage precautions Electrical interference For safety considerations the 510 has been designed to provide maximum protection against the emission of electromagnetic radiation from inside the device and from external interference However equipment that is very susceptible to interference or that emits powerful electromagnetic waves should not be placed near the 510 as the possibility of interference cannot be ruled out entirely This symbol indicates explanations about extremely dangerous issues If users ignore this symbol and handle the device incorrectly serious injury or death could result This symbol indicates explanations about dangerous issues If users ignore this symbol and handle the device the wrong way bodily injury and damage to the equipment could result Whatever the type of digital control device
14. flect ype gt ES PARAMETER 2 GAIN Sets the effect parameter value for PRE DRIVE Which parameter is being adjusted depends on the effect type MIX Adjusts the effect mixing level PRE DRIVE parameter setting Increases or decreases the setting by 1 aS VALUE keys selected with parameter 1 Skips to 10 if the current setting Setting range C 1 to 9 and to 16 if 10 to 15 n BSS PARAMETER 3 MAIN DRIVE Selects the effect type to be used in the MAIN DRIVE module 8 different effect types are available Setting range increases the setting by 1 efect ype gt ES PARAMETER 4 GAIN Setting range Fa 0 e SENS Sensitivity Adjust the effect sensitivity FREQ Frequency Sets the center frequency that is active immediately after a patch is selected GAIN Adjusts the PRE DRIVE gain Higher values result in higher Higher values result in higher PRE DRIVE gain and increased distortion oe sensitivity Higher values result in higher effect mixing level Higher values result in higher center frequency When changing the effect type with parameter 1 the immediately preceding value of parameter 2 is memorized 1 OVER DRIVE 2 BLUES OD 3 FAT DRIVE 4 DISTORTION 5FUZZ 6GRUNGE 7 LEAD 8 METAL Blues overdrive Distortion effect with a sound Fuzz effect Modern fuzz Lead sound Metal type sound Trebly overdrive which makes a
15. g low this indicator begins flashing at a faster rate than in Edit mode In such a case replace the battery as soon as possible IN 16 16 Teepac wan 7 uan secre _ eum PARAMETER CURSOR indicator AN Pd 1 30 Play mode SH 5 15 The currently used effect module lights W 15 15 a 7 Edit mode asus Lae of patches are to be stored this key is used for putting the unit in ied The indicator lights up for the currently used effect module and the indicator stare eta HEROS i Oikia flashes for the effect module that is turned off Also the indicator for the effect Sse aa n este fu igtion sown aa m i module selected for editing flashes When the STORE key is pressed for at least 1 second during Play mode during lice Bypass Tumer mode performance the direct load function can be switched on or off For details see 10 S ndicators tunction as tuning meter Patch Switching Application Direct Load OFF P pe y X VALUE keys C e Play mode E DIT key for creating your own patches i s The keys serve for bank switching This key serves to toggle between the Play mode and Edit mode mode for creating a Zl Edit mod patches to suit your taste ut mode In Edit mode this key can be used to select the effect parameters you wish to f change Also when the effect parameter SERIAL PARA is selected press this J J Bypass Tuner mode EDIT key to return from the Edit
16. g range Increases or decreases the setting by i 63 09 09 1 l VALUE keys E to 10 if current setting is 15 to 11 to 0 if 10 to 1 BD to 10 if 0 to 9 and to 15 if 11 to 14 ZNR settings amp simulator on off LOW Controls the low frequency range Negative values cause a low range cut and positive values a low range boost PARAMETER 7 znr AMP Setting range B 03 63 69 ZNR and amp simulator off ZNR on amp simulator off Higher values result in more effective noise reduction Choose the highest value that is possible without causing the sound to become unnatural ZNR off amp simulator on E Ag ZNR and amp simulator on Higher values result in more effective noise reduction ZNR is Zoom s original noise reduction which cuts noise level during pauses This parameter adjusts the ZNR sensitivity as well as the amp simulator on off setting which simulates the sound of an amplifier box increases or decreases the setting by D gt VALUE keys Skips to oF 1 A1 SS PARAMETER 8 LEVEL Patch level increases or decreases the setting by D gt HA VALUE keys skis to 10 20 30 if current setting is 1 to ESS PARAMETER 9 SERIAL PARA Setting range F roar E T Increases Or decreases the setting by D gt e 6 l 5S VALUE keys l al 69 skies to Sr P1 A1 al Da x pS Selection of parameters tochange As described
17. h and switches the output sound on the display the number flashes but until the user confirms the choice the sound remains that of patch 1 To turn Direct Load on or off keep the STORE key depressed for at least 1 second To confirm a choice after selecting a patch with Direct Load off press both patch pedals simultaneously Patch switching completed Confirm fy Editing Patches The 510 comes with 24 predefined patches However the 510 offers many more possibilities for combining effects in innovative ways To discover these possibilities we recommend that you try changing the parameters elements that make up patches to create your own patches This operation is called editing and is done in the Edit mode To switch from normal Play mode to Edit mode press the EDIT key briefly for less than 1 second Note that if the EDIT key is held down for 1 second or longer the Bank Hold mode will be activated 1 While still in Play mode select 2 Press the EDIT key to the patch you wish to edit activate the Edit mode There are a total of eight indicators assigned to parameters 1 8 from top to bottom plus the TUNER indicator which is assigned to parameter 9 The parameter functions are as follows Parameter 1 PRE DRIVE PRE DRIVE effect type selection Parameter 2 GAIN PRE DRIVE
18. in 11 Editing Patches parameters to be edited are selected by repeatedly pressing the EDIT key but you can also use the patch pedals for this purpose T Setting range C 60 Sets the overall patch level Higher values result in higher level Serial parallel Serial connection a F Parallel connection 2 Larger values result in a higher MAIN DRIVE mix level Auto parallel connection where the PRE DRIVE and MAIN DRIVE level balance is controlled by the picking intensity The harder the mj picking intensity the stronger the MAIN DRIVE influence Auto parallel connection The harder the picking intensity the stronger the PRE DRIVE influence Pedal serves to control the PRE DRIVE and MAIN DRIVE level balance Determines the connection principle of the PRE DRIVE and MAIN DRIVE modules serial or parallel The parameter also controls the mix level balance setting for parallel connection the auto parallel setting and the pedal balance control setting To switch the PRE DRIVE module on and off In Edit mode while parameter 1 or 2 is selected press the PATCH UP and DOWN pedals together to turn the PRE DRIVE module off The display indication for parameter 1 becomes oF and for parameter 2 For any module that is turned off pressing the PATCH UP and DOWN pedals together or pressing a VALUE key once turns the module to on again and restores the parameter
19. m Patch 2 PATCH 2 Bank A to Patch 3 Bank C the patch PATCH 3 pedal would have to be pressed nine PATCH 4 times Instead you can press the VALUE key twice to switch to Bank C and then press the patch pedal UP just once to select Patch 3 PATCH 1 PATCH 2 PATCH 3 PATCH 4 Bank patch switching when Bank Hold is off initial setting 8 Using the Bypass Tuner Mode The effects of the 510 can Tuner ON OFF be t d off b d Pressing the EDIT key and the STORE key simultaneously for more than one second in e turned o ypasse Play mode will allow you to select whether or not to activate the tuning function in Bypass temporarily so that only the mode When you change the setting the display will show tunEr oFF tuning function off ce or tunEr on tuning function on according to the setting original sound of the instrument is heard In this Calibration mode the auto chromatic Select reference pitch for auto chromatic H uitar tuner calibration tuning function via the LED 9 display is also active The reference pitch A can be adjusted in the range from 435 to 445 Hz When the BANK key is pressed in Bypass Tuner mode this is shown as 35 to 45 on the display for a second Adjust to the suitable Bypass mode 4 value At power on the setting is 440 Hz 40 Pressing both patch pedals f Bypass ON OFF simultaneously activates
20. n PATCH 1 PATCH 1 PATCH 2 PATCH 2 _PATCH 3 PATCH 3 PATCH 4 PATCH 4 PATCH 1 PATCHT _PATCH2 PATCH _PATCH 3 sarong PATCH BANK HOLD ON PATCH 4 BANK HOLD OFF In the default condition the 510 is DIRECT LOAD OFF set up in such a way that pressing a Keeping STORE key depressed for 1 second patch pedal immediately switches turns Direct Load off the patch and alters the output The same procedure serves to turn it on sound This is called Direct Load ON This switching principle is most convenient when the desired patches are adjacent or close to each other However when Bank switching wanting to switch to a patch that is Banks A b C d E F further away it may be desirable can be switched not to activate the sound of the other patches in between When this is desired turn the Direct Load function off as follows When Direct Load has Patch switching been turned off switching banks Patches can be switched and patches has no effect until the user confirms the selection For example when going from patch to patch 4 with Direct Load active patches 2 Confirming a patch and 3 will briefly be heard when the patch UP pedal When display indication flashes pressing is pressed three times When Direct Load is off both patch pedals together confirms the pressing the patch UP pedal will change the number patc
21. or Maximum simultaneous effects 5 Banks and Patches 6 banks x 4 patches 24 patches edit store possible Analog Digital Conversion 18 bit 128 times oversampling Digital Analog Conversion 16 bit linear Sampling Frequency 44 1 kHz Input Guitar input standard monaural phone jack Rated input level 20 dBm Input impedance 470 kilohms Outputs Combined line headphone output standard stereo phone jack Max output level 6 dBm Output load impedance 10 kilohms or more DIRECT OUT standard monaural phone jack Control Input For optional FP01 or FSO1 Display 2 digit 7 segment LED tuning indicator parameter cursor indicator Power Requirements Optional AC adapter 9 VDC 300 mA Zoom AD 0006 Battery 6LR61 9 V alkaline battery x 1 Battery life Approx 4 h continuous operation Dimensions 147 W x 157 D x 49 H mm Weight 480 g without batteries 0 dBm 0 775 Vrms Design and specifications subject to change without notice
22. parameter setting Parameter 3 MAIN DRIVE MAIN DRIVE effect type selection Parameter 4 GAIN MAIN DRIVE parameter setting e Parameter 5 HIGH High range equalizer 12 Effect Parameters PARAMETER 1 PRE DRIVE Selects the effect type to be used in the PRE DRIVE module 8 different effect types are available PRE DRIVE effect type Increases or decreases the setting by 1 effect type VALUE keys Immediately after entering Edit mode from Play mode the topmost parameter cursor indicator PRE DRIVE flashes and the setting of this parameter is shown on the display The flashing parameter cursor always indicates which parameter is selected for editing Parameter 6 LOW Low range equalizer Parameter 7 ZNR AMP ZNR setting amp simulator on off e Parameter 8 LEVEL Patch level Parameter 9 SERIAL PARA Serial parallel connection In Edit mode the EDIT key or the PATCH UP DOWN pedals serve to select the parameter Each push of the EDIT key moves the blinking parameter cursor indicator one step down The PATCH UP DOWN pedals move the blinking parameter cursor indicator up or down When the EDIT key is pressed while the lowest indicator Parameter 8 LEVEL is flashing the TUNER indicator Parameter 9 SERIAL PARA starts flashing When the EDIT key is pressed while the TUNER indicator Parameter 9 SERIAL PARA is step down 1 Use the EDIT key or patch pedal to select th
23. rameters set to certain values PRE DRIVE and MAIN DRIVE each contain eight effect types from which you can choose one The effects from PRE DRIVE and MAIN DRIVE can be combined linked in two different at a time Each effect type in turn is made up of several effect parameters that determine the ways as described below The type of link is also stored as part of the patch e SERIAL PARALLEL PRE DRIVE and MAIN DRIVE are connected in series one after the other PRE DRIVE and MAIN DRIVE are connected in parallel side by side and For example PRE DRIVE could first apply light distortion and then MAIN their output is mixed For example PRE DRIVE could apply the OCTAVE DRIVE could add heavy distortion effect and MAIN DRIVE the OVERDRIVE effect simultaneously SERIAL PARALLEL PREDRIVE HIGH ZNR HIGH ZNR PRE DRIVE MAIN DRIVE H amp LOW AMP TT amp LOW AMP KJ Controls Functions and Connections Front Panel DISPLAY a Displays information required to operate the 510 TUNER indicator Play mode Bypass Tuner mode Displays the selected bank A F and patch 1 4 Indicator shows that tuning function is active and also serves to show the correct NEE EEEE Edit mode cation position PRE DRIVE Displays the value of the selected effect parameter e Edit mode 1 OVER DRIVE eee ieee __ Shows te ch of the input signal When the unit is powered from the battery and the battery is runnin
24. s when driving a large reminiscent of effect with characterized with prominent it easy to control nuances amplifier to full levels the psychedelic exciting sound by a mild tone lows and highs with picking intensity Suitable for seventies type sound of the hard rock sixties MAIN DRIVE effect type Increases or decreases the setting by 1 effect type B VALUE keys Overdrive effect ranging from clean sound to fat distortion Conventional overdrive effect MAIN DRIVE parameter setting GAIN Adjusts the MAIN DRIVE gain Higher values result in higher MAIN DRIVE gain and increased distortion Increases or decreases the setting by D gt VALUE keys Skips to Pd 1 10 20 30 ES Equalizer HIGH range setting When Pd is selected the optional expression pedal FP01 can be used to adjust gain When changing the effect type with parameter 3 the immediately preceding value of parameter 4 is memorized PARAMETER 5 HIGH Setting range 63 00 09 HIGH l d the setting by 1 Increases cea Paeaaceaaca es D gt Controls the high frequency range VALUE keys FADS Equalizer LOW range setting Negative values cause a high range cut and positive values a high range boost Skips to 10 if current setting is 15 to 11 to 0 if 10 to 1 to 10 if 0 to 9 and to 15 if 11 to 14 PARAMETER 6 Low Settin
25. switch Connect to equipment with high input impedance such as a guitar amplifier or other ZE e When the expression pedal FPO1 is connected effect device X9 9 The pedal controls a function determined by a parameter of the currently selected a ZOOM CORPORATION patch as described below When the 510 is used together with the DUAL POWER MODULATOR 509 making MADE INJ APAN 300ma gt nan the connection as shown below ensures that the HPS Harmonized Pitch Shifter 1 Parameter 1 PRE DRIVE effect type set to 7 pedal wah effect of the 509 works correctly N Pedal functions as pedal wah 2 Parameter 4 GAIN parameter of MAIN DRIVE set to Pd INPUT OUTPUT INPUT OUTPUT Pedal controls gain of MAIN DRIVE To amplifier 3 Parameter 9 Serial parallel switching set to Pd 509 or other effect device Pedal controls mixing balance of PRE DRIVE and MAIN DRIVE modules Functions 1 3 can be used simultaneously For patches where 1 3 do not C apply the pedal serves as volume pedal to control the overall output level For details please refer to the operation manual of the DUAL POWER MODULATOR 7 S 509 E OUTPUT jack This jack is for the output signal from the 510 You can connect either a single a DC IN AC adapter jack guitar amplifier using a monaural shielded cable or two guitar amplifiers using Serves for connecting an AC adapter Zoom AD 0006 which delivers 9 VDC 300 a
26. the original patch that was used as a starting point for editing will not be changed 2 Press the STORE key 4 Press the STORE key once more Unit enters store standby mode Store process is completed If the tuning indicator flashes while the unit is being powered from the battery the battery is exhausted and should be replaced as described below Use only a 6LR61 9 V alkaline battery Using another kind of battery will result in shorter operation Turn the 510 upside down and open the cover of the battery compartment Push the catch to unlock the cover then lift it up Remove the battery from the compartment and disconnect the battery cable Grasp the terminal strip and do not pull at the cable Connect the battery cable to the new battery taking care to observe correct polarity Then insert the battery into the battery compartment Close the battery compartment cover taking care not to pinch the cable Make sure that the cover is properly locked fF Returning Patches to Factory Settings The 510 comes with 24 predefined patches that have been programmed at the factory Also after you have edited and stored your own patches you can return to the factory default settings at any time This process is called recalling Returning all 24 patches to the original contents and resetting the Bank Hold and Direct Lo
27. to the original setting that was active before the module was turned off twice which will change the value to 10 and then press the VALUE key 2 times to arrive at 12 Master level adjustment Press the PATCH UP pedal right patch pedal to move the parameter cursor from the bottom up Press the PATCH DOWN pedal left patch pedal to move the parameter cursor from the top down Effect module on off switching The PRE DRIVE MAIN DRIVE and ZNR AMP modules can be switched on and off individually and the status can be stored as part of a patch To switch the MAIN DRIVE module on and off In Edit mode while parameter 3 or 4 is selected press the PATCH UP and DOWN pedals together to turn the MAIN DRIVE module off The display indication for parameter 3 becomes oF and for parameter 4 Parameter setting shortcuts With the 510 you are also able to set the master level that governs the 7 overall output level Normally parameter values are set by tapping the VALUE or VALUE key once for each increment or decrement For quick operation you can use the shortcut function This is activated in the Edit mode by pressing both VALUE keys together For example if GAIN parameter 4 of the MAIN DRIVE module is set to Pd pedal controls gain and you want to change it to 12 you would have to press the VALUE key 12 times Instead you can achieve the same effect by using the shortcut function press the VALUE keys togeth
Download Pdf Manuals
Related Search