Untitled - Microh DJ
Contents
1. Auto mode and music mode Manual mode 1 When the power is turned on the unit enters manual mode automatically 2 Check and verify that both the Auto and Music LEDs are off 3 Select the desired chase by pressing one of six Chase buttons with the bank you wish to run 4 Use the Bank Up Down button to select the bank with the scenes you wish to run 5 Press the scene button corresponding to the scene you wish to display lf more than one scene button have been pressed he controller will play the scene with bigger number Auto Mode 1 Press the AUTO button to activate Auto mode 2 Select the desired by pressing one of six Chase buttons Pressing this button a second time will negate this selection If the chase has no data the LCD displays Empty 3 Use the speed slider or tap the Tap Sync button twice to adjust the speed use Fade Time slider to adjust fade time of the scene progression 4 Tap the AUTO button to exit Auto mode Music Mode 1 Press the SOUND button to activate Music mode 2 Select the desired chase by pressing one of six Chase buttons this will activate the chase and cause it to respond to the rhythms of music 3 Use the Fade time slider to adjust the fade time of the chase progression 4 Tap the SOUND buiton to exit music mode 9 KEY FEATURES e 192DMX Channels e 30 Banks each composed or 8 programmable scenes e 3 Fades adjusting output level e Built in Microphone e AUTO mode is controlled b2. ON ON 10 145160 ON ON n sw ON ON Yo va on ON amp Scene Buttons 1 8 Press one scene button to run scene or to store scene and the second digit of LCD DISPLAY shows scenes 1 8 Faders Slide the fades to adjust the output level or DMX channel from 0 to FF 255 Page Select press to select page A to page B Speed Slider Used to adjust the scene or chase speed within the range of 0 1 second to 10 minutes Fade Time Slider Used to adjust the scene or chase fade time within the range of O second to 30 seconds 0 second is off fade function LCD Display Shows the current activity or programming state Bank Up Down Press the Up Down button to select from 30 banks Chase Button 1 6 These buttons are used for activating the chase of programmed scenes Prog Button Activates program mode Add MIDI button a Press MIDI key when running the third and fourth digit of LED flash select MIDI channel using UP or DOWN press MIDI key once more or any other key excluding UP or DOWN to end the MIDI cannel setting b Press this key to make programs when in PROGRAM mode Del Auto button Used to delete scene or chase Music Bank copy button a In RUN mode press this key corresponding LED is ON which indicates it is in MUSIC mode Press once more to withdraw MUSIC mode corresponding LED goes out b Press this key to make Scene and chase program when in PROGRAM mode Ta
3. E MICROH E FIXTURES O e e e wd e MIEROFM zz www microhdj com SCENES 8 8 E REL NE 3888 Program Chase Scene Bank 0 1SEC Program DD Midi Add m Autc Del e 4 7 P 9 on DMX DICTATOR192 FADE TIME USER MANUAL DIVIX DICTATOR 192 Keep this manual for future reference O gt a d gt e D DB HOEDIIA i 1 INTRODUCTION AND UNPACKING Thank you for purchasing the MICROH DMX DICTATOR 192 controller For your own safety and knowledge please read this manual before installing or operating the device This manual covers the important information on installation and applications Please install and operate the fixture according to instructions Meanwhile please keep this manual for future reference The MICROH DICTATOR 192 DMX controller is manufactured following CSA standards complying with international standard DMX512 protocol This controller is applicable but not limited to large scale live performances theater studio nightclubs and discos The MICROH DMX DICTATOR 192 controller features a two colour laser strobe and a moonflower effect Please carefully unpack it when you receive the fixture and check if it was damaged during the transportation Please check whether the following items are included inside the box Controller One Power Adapter One User Manual One 2 SAFTEY INSTRUCTIONS CAUTION AN ELECTRIC SHOCK WARNING USE EXTREME CAUTION WHEN HAND
4. Editing 1 Select desired scene of bank 2 Make program of scene to meet the requirement of device 3 Press MIDI ADD 4 Press scene to store this scanner Copy a Scene 1 Select desired SCENE 2 Press MIDE ADD once 3 Select one bank Then press the scene to copy to Copy a Fixture 1 If a scanner is set press and hold the FIXTURE first 2 Press the FIXTURE to copy to and then the FIXTURE is copied to anther FIXTURE Deleting Scenes 1 Select desired scene 2 While pressing and holding AUTO DEL Press scene required to be deleted Resetting All Scenes 1 Press PROGRAM DOWN while turning power off 2 Turn the power on Copying a Bank 1 Select desired bank 2 Press MIDE ADD 3 Select the bank to copy to 4 Press MSIC BANKCOPY Delete All Banks select the bank to be deleted press Auto DEL Music Bank copy 7 CHASES Press PROGRAM Corresponding LED flashes which indicates it is in PROGRAM mode Copy a Scene of a Bank to a Chase 1 Enter program mode See Enabling Program Mode 2 Tap the Chase button to select the chase wish to program The LCD will display how many steps have already stored in the chase if the chase already has been programmed 3 Tap the bank Up Down button to choose the desired bank that has scenes stored inside it In each bank the scenes buttons that contain data will light ON solid green This lets the user know that there is a scene already programmed there 4 Press t
5. LING WIRES This device has been delivered in safe working condition In order to maintain this condition and to ensure safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual gt Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature and is dry This device falls under protection class therefore it is essential that the device be grounded The electrical connection must be carried out by a qualified technician The device should only be used with rated voltage and frequency Make sure that the available voltage is not higher than 120V as stated at the end of this manual Make sure the power cord is never crimped or damaged in any way as this could cause shock and damage If your power cord is damaged in any way please purchase a new cable from your local MICROH dealer Always disconnect power when the device is not in use or before cleaning it Never pull out the plug by tugging the power cord Fixtures cannot be installed on or near combustible substances Keep more than 50cm distance from wall for proper ventilation and air flow lf yo
6. ailed 8 PLAYBACK Running Scenes Turn the power on it is in MANUAL RUN mode When in PROGRAN mode press PROGRAM for 2 seconds PROGRAM LED goes out it enters MANUAL mode If there is not any scenes having been programmed in a bank the scene can t be run only the SCENES having been programmed are executed If the fades is set to OFF Scene will execute channel program setting Manual Mode 1 Extinguish AUTO triggered LED and MUSIC triggered LED 2 Select a bank using 7 of 1 MIDI signals through MIDI interface 3 Press scene to run scene 4 Run scene using MIDL Auto Mode 1 Press AUTO DEL corresponding LED is ON 2 Press TAP SYNC DISPLAY Press it once more some time the interval between two pressing is assigned to the speed of AUTO RUN the maximum limit is 10 minutes If there are many pressings more than twice the last two pressing are designated 3 Select desired bank using UP or DOWN via MIDI signals 4 Press Auto DEL once more to withdraw ATO RN mode Music Mode 1 Press the SOUND button to activate Music mode 2 Use the bank Up Down button to select a bank of scenes you will to run the scenes selected will run through sequentially the beat of the music identified by the built in microphone 3 Use the Fade time slider to adjust the fade time of the scene progression 4 Tap the SOUND button to exit music mode Running Chases There are three modes in which you can run chases They are Manual mode
7. he desired Scene button to select the scene you wish to copy it to the desired chase 5 Tap the ADD button If the LCD displays Saved means the chase have been successfully stored if the LCD displays Saved fail means the chase store failed 6 Repeat steps 3 5 until all desired scenes have been entered Copy All Scenes of a Bank to a Chase 1 Enter program mode See Enabling Program Mode 2 Tap the Chase button to select the chase wish to program 3 Tap the bank Up Down button to choose the desired bank that has scenes stored inside it In each bank the scenes buttons that contain data will light ON solid green This lets the user know that there is a scene already programmed there 4 Tap the ADD button If the LCD displays Saved means the chase have been successfully stored if the LCD displays Saved fail means the chase store failed 5 Repeat steps 3 4 until all desired scenes have been entered Add a Step 1 Enter program mode See Enabling Program Mode 2 Tap the Chase button to select the desired chase you wish to add a step to The LCD will display how many steps have already stored in the chase 3 Tap the Tap sync button 4 Tap the bank Up Down button to scroll to the step which you wish to insert the step after You can read the step from the LCD Display 5 Tap the ADD button 6 Tap the bank Up Down button to choose the desired bank that has the desired scene stored which you wish to add In each ba
8. nected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1200 a h i PIN3 PIN 2 5 OPERATION General The 512CH DMX Controller allows you to program 512 DMX channels each 30 banks of 16 Programmable scenes 6 chases of 480 scenes using 16 channel sliders and other buttons With the SD card slot you can insert SD card to record whole data of controller or edit SD card data with computer to run on the controller Display Information When power on the controller the LCD displays WiFly WLC16 V1 0 The LCD Display contains a maximum of 2 lines each of 16 characters below are the definitions LCD Display Message Scene 01 Scene 1 is activated Bank 01 Bank 1 is activated Chase 01 Chase 1 is activated CH01 255 Channel 1 DMX Value 255 SPEED Time 05 30 0 The current speed is 5 minute 30 seconds FADE Time 15 0 The fade time is 15 seconds Step020 Step 20 is activated or the chase contains 20 steps 6 SCENES Programming a Scene 1 Press FIXTURE key to select DMX channel composed of 8 channels Select different channel to control several devices at the same tine Adjust appropriate fades to select desired output level than turn off fade Select and adjust output level continuously until all devices are set Press MIDI ADD Select desired bank using UP or DOWN Press SCENE to store this SCENE NO 01 amp W MN Scene
9. nk the scenes buttons that contain data will light ON solid green This lets the user know that there is a scene already programmed there 7 Press the desired Scene button to select the scene you wish to add 8 Tap the ADD button If the LCD displays Saved means the step have been successfully added if the LCD displays Saved fail means the step add failed EXAMPLE Add scene 2 of bank 3 between step 4 and 5 of chase 5 1 Enter program mode See Enabling Program Mode 2 Tap Chase 5 button The LCD will display how many steps have already stored in chase 5 3 Tap the Tap sync button 4 Tap the bank Up Down button to select step 4 You can read the step from the LCD Display 5 Tap the ADD button 6 Tap the bank Up Down button to choose bank 3 The scenes buttons that contain data will light ON solid green in bank 3 This lets the user know that there is a scene already programmed there 7 Press Scene 2 button to select the scene 2 8 Tap the ADD button The LCD displays Saved means the step have been successfully added Now the scene 2 of bank 3 is the new step 5 the previous step 5 turns to the new step 6 the previous step 6 turns to the new step 7 and so on Delete a Step 1 Enter program mode See Enabling Program Mode 2 Tap the Chase button to select the desired chase you wish to delete a step The LCD will display how many steps have already stored in the chase 3 Tap the Tap sync button 4 Tap the bank Up D
10. own button to scroll to the step which you wish to delete You can read the step from the LCD Display 5 Tap the DEL button If the LCD displays Deleted success means the step have been successfully deleted if the LCD displays Deleted fail means the step deleted failed EXAMPLE Delete step 3 of chase 4 1 Enter program mode See Enabling Program Mode 2 Tap Chase 4 button The LCD will display how many steps have already stored in the chase 3 Tap the Tap sync button 4 Tap the bank Up Down button to select step 3 You can read the step from the LCD Display 5 Tap the DEL button The LCD displays Deleted success means step 3 has been successfully deleted Now the previous step 4 turns to the new step 3 the previous step 5 turns to the new step 4 and so on Delete a Chase 1 Enter program mode See Enabling Program Mode 2 Press the button corresponding to the chase you wish to delete 3 Press the DEL button Ifthe LCD displays Deleted success means the chase have been successfully deleted if the LCD displays Deleted fail means the chase delete failed Delete all Chase 1 Enter program mode See Enabling Program Mode 2 Press the any one of chase button 3 Tap any one of scene button to set to scene 0 4 Press and hold the DEL button for about 15 seconds lf the LCD displays Deleted success means all the chases have been successfully deleted if the LCD displays Deleted fail means all the scenes delete f
11. p sync button Repeatedly tapping this button to establish the chase speed or check the step in chase Blackout Button Press this button to pause whole output POWER MIDI IN IMa POLARTTY IMA OUT a INPUT GQ 9 Tu0v 12V S00mA min 16 MIDI IN DC12V 500mA min 17 DMX Polarity Switch Polarity of the DMX output 18 DMX OUT 19 DC IN DC 9V 12V 300 mA min 4 DMX 512 CONTROL CONNECTIONS This controller complies with international USITT DMX standards and can be used with either a 3 pin or 5 pin DMX connector Plug in any 3 or 5 pin XLR cable to the female 3or 5 pin XLR output of the unit and the other side to the male 3 or 5 pin XLR input of the fixture To connect the units to DMX you must daisy chain the fixtures together as referred in the diagram below Always end your DMX 512 connection with a DMX terminator DMX OUTPUT CONTROLLER FIXTURE 1 FIXTURE 2 FIXTURE 3 REPEAT UP TO 30 UNITS IN a er EN SES ENS 32323925J3 y Le Le EA Ze Le In e XLR CABLE XLR CABLE XLR CABLE DMX Output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket COMMON 1 Ground DMX512 OUT Wwe DMX512 IN 2 Data For installations where the DMX cable has to run a long distance or is in an electrically noisy environment it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 0 resistor con
12. ur fixture is or has become damaged in any way it shall be exclusively replaced or repaired by the manufacturer to avoid any hazard CAUTION Never touch the device during operation The housing may heat up CAUTION Never look directly into the light source as sensitive persons may suffer an epileptic shock CAUTION The electric connection must only be carried out by a qualified electrician 3 CONTROLS AND FUNCTIONS o a i o zi 10 j 4 11 ern 12 9 21 13 mm u u 0 57 u 70 mm 5 14 15 63 dal Cn 1 Fixtures Buttons 1 16 Press desired scanner corresponding LED is lit and appropriate channels is enabled to be adjusted when scenes are running if fades control is OFF channel output level is not controlled by the fades if fades control is ON channel 8 output level is controlled by the fades Fixture Channel Fade control LED 1216 X OF OF L2 m3 OF OF L3 33348 gt X OF Ot L4 496 OF OF 5 658 X OF Or 6 896 oF OF 8 42328 oF OF 9 429144 or OF 10 11 12 13 14 15 Fixture Channel Fade control ED 1 t ON ON a 2 o ON ON L3 338 ON ON L4 498 on ON 5 68 ON ON 6 896 ON ON L7 972722 ON N 8 mn ON ON 9 202 4 X
13. y TAP SYNC and SPEED controlled e MIDI control through MIDI interface e A digits LED display e Blackout master controlled by Manual or Remote e CHASE programming and CHASE running manual control and remote control e Fade Time control e DMX polarity selects 10 10 TECHNICAL SPECIFICATIONS Power Input DC9V 300mA min DMX Out 3 pin female XLR socket Dimensions 482x132x 3mm Weight 2 5kgs 11 MAINTENANCE AND CLEANING The following points have to be considered during the inspection 1 All screws for installing the device or parts of the device must be tightly connected and must not be corroded 2 There must not be any deformations on the housing colour lenses fixations or installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage must be handled by a skilled installer or technician Any safety issues must be resolved CAUTION DISCONNECT POWER BEFORE SERVICING dr In order to keep the fixture in good condition and extend the life we suggest regular cleaning to the fixture 1 Clean the inside and outside lens each week to avoid the light output from darkening due to accumulation of dust dirt etc 2 Clean the fan each week 3 Adetailed electrical check b
14. y approved technician every three months is advised Ensure the circuit contacts are in good condition We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine MICROH parts from your local dealer 11 IF YOU SHOULD EXPERIENCE ANY PROBLEMS OR ISSUES PLEASE CONTACT MICROH PROFESSIONAL PRODUCTS BY EMAIL AT info microhdj com In the event that your unit is defective in any way please contact your local dealer to obtain an RA number for service repair DISCLAIMER MICROH believes that the information contained within this user manual is accurate However Microh is not responsible for any error or addendums to this manual If you have any comments or general suggestions on how this manual can be improved please contact info microhdj com Thank you 12 NOTES 13 NOTES 14 MIEROF www microhdj com
Download Pdf Manuals
Related Search