User Manual Version 2
Contents
1. LO 4 XSD27ZS Operating Manual Contents 399 AARM BIA ge 15 3 3 9 DEFAULTED SETTING arazua 16 4 TROUBLESHOOTING ccc ccc ccc e mr nre enmt eene eere eere eene 16 4 1 16 dugo XSD2725 Operating Manual SAFETY CAUTION WARNING User shall be reminded to avoid the risk including potential deaths or severe injuries 1 Please refer to the ambient requirement for equipment when installation do not install this equipment in the environment with too much moisture dust and smoke dust which may result in fire or electric shock 2 In case that this equipment emits abnormal smell or smoke please immediately stop it shut off the power and contact the supplier otherwise this equipment may result in fire or electric shock 3 During cleaning this equipment do not directly spray water on any part of this equipment which may result fire or electric shock 4 Please do not place this equipment near a heat source otherwise a fire risk is potential 5 It is forbidden to store install and use this product in danger areas with inflammable or explosive substances NOTICE Please carefully read the instruction book before installation 1 During transportation storage and installation heavy load violent vibration and immersion shall be prevented to avoid the damage of the equipment 2 Be2. X VISION XSD27ZS Operating Manual 3 3 MENU SET 3 3 1 BASIC MENU OPERATION 3 3 2 3 3 3 1 Press control keyboard or use matrix to execute the command of call 95th preset location to enter and set main menu 2 After the main menu page appears press up or down icon to move the cursor to the submenu option to be set and press right icon to enter this submenu setting page 3 After submenu page appears press up or down icon to move the cursor to the option to be set and press right icon to change or set the content of this option 4 The contents normally fall into 2 types Digit type and List Type The blink indication means that the content of the option can be changed For Digit type press the left or right icon to select the input location press up or down icon to modify the value To confirm and quit the option setting move the cursor to the last digit and press right For List type press up or down to modify the content of option and press right to confirm and quit the option setting MENU SET MAIN MENU 1 System Information Check dome information such as version address communication etc Camera Setting Set the camera parameters Privacy Shelter Set the parameters for privacy masking Auxiliary Setting Set some auxiliary parameters of the dome Scanning Setting Set the scan sequence of preset location Title Setting Set regional title by input method Alarm Linkage A
3. is a performance unit Therefore it is widely used in various areas such as Airports stations Supertores Banks and Hospitals 1 2 PRODUCT FEATURES Supporting CVBS standard definition video signal output m Driven by accurate step motor with stable running and low noise m Upto255 programmable preset locations m Several scan modes such as area scan preset location scan pattern scan etc Multi function Chinese English menu with flexible and easy configuration X Vertical and automatic over turn function can realize the continuous watch without blind area Telephoto and limit speed function provides a clear and stable monitoring picture m Self adaptive baud rate and communication protocol m Non polarity RS485 supports broadcast address and soft address m Supporting failure detection indication for RS485 communication IP66 Protection grade IP 66 m Ultra lowpower consumption and ultra strong stability XSD2725 Operating Manual 1 3 TECHNICAL INDICATORS T NN rr Prese location running a we E sea o TZ ez erra ere BE EEE Communication Failure Yes error indications such as baud rate error address error LS ete bild PELCO D PELCO P Industrial protocol DH SD1 YAAN 19 Integrated protocol self adaption RS485 Supporting non polarity XSD2725 Operating Manual 2 HARDWARE INSTALLATION Address setting The address
4. 27ZS Operating Manual 103 CALL Switching linear scanning speed fast slow and medium 105 CALL Starting digital zoom 3 2 KEYBOARD OPERATION 3 2 1 PRESET LOCATION SCAN 1 Set preset location scan Preset location scan routine can be set using 2 ways See Menu set gt Scan Set There are a total of 4 preset location routines and 32 preset locations that can be set The 40th and 43rd preset locations are in turn used to set and call the 1st and 4th preset location routines 1 Execute the command of setting 40th preset location to enter the set status 2 Call the desired set option to the preset location in routines such as the first the second etc 3 Wait a desired time to stay the interval time between two location and do not conduct any operation 4 Call next routine that you want to set to preset location If there are unused preset location add it into routine execute in looping way the 3 and 4 or execute 5 and the set is over 5 Execute the command of setting 40th preset location and save the set and exit in addition to calling preset location Executing any command other than such as up down right or left does not need to be saved before exit 2 Run preset location scan call 40th 43rd preset locations to run 1st 4th group preset scan location series 11 A XSD27ZS Operating Manual 3 2 2 3 2 3 AREA SCANNING There are two ways to set the area of scann
5. 6 vision 502725 High Resolution 600 TVL Speed Dome CCTV Camera 27x Optical Zoom User Manual A Vision XSD27ZS Operating Manual Contents 1 OVERVIEW 1 1 BRIEF INTRODUCTION AND APPLICA TON sieh ei EE 5 L2 PRODUCTFEATURES ataundarra aiarar 5 Edge AISA RIAU SUL SAS Se 5 2 HARDWARE INSTALLATION 6 2 1 ADDRESS SEFUN ina date Tes oi edad adio ou Lind etd 6 3 OPERATION INSTRUCTION a epe pre beste qa w 8 3 1 MAPPING TABLE FOR PRESET EOGA LION aea 8 3 2 KEYBOARD OPERATION La gia q e omis ar sles ee adieu Ad oaa Mas euam ia utram 11 3 2 1 PRESET LOCATION SCAN aza a EEE ebek 11 922 2 AREA SCANNING epo kia VE ancora TENER VERENA ERIT DOPO ERROREM AREE 12 SARR TAKO EAN AN EEA 12 3 3 13 3 3 1 BASIC MENU OPERATION i d on de ra ya PE PEE Eu RR na 13 3 22 MENU SET adan retis atateko 13 35533 SYSTEM INFORMATION Ea a EE Ue 13 3 9 4p CAMERA SETTING E aX RI E te cuter wns REA ad haa dex a 14 3 3 5 AUXILIARY SETTING aa US OU 15 33 6 SCANNING SET sii tuit Eu Fe E S PE tenes 15 39 7 TILE SET to hd oko 15 A
6. and low case characters symbols number and Pinyin 6 Delete To delete the characters in the insert characters of title 7 Exit Exit the sub menu without saving the modification 8 Save Save the settings and exit sub menu 3 3 8 ALARM LINKAGE 1 Alarm Input Alarm input No 1 and 2 2 Input Type On and Off 3 Arming Time Hours Minutes 15 BA A Vision XSD27ZS Operating Manual 4 Disarming Time Hours Minutes 5 Presetting Scanning Linkage preset location scanning No 0 4 O means the scanning without linking presetting 6 Pattern Scanning Linkage pattern scanning No 04 O means the pattern scanning without linking 7 Area Scanning Linkage area scanning No 0 4 O means the area scanning without linking 8 Alarm Output On and Off 9 Exit Exit the submenu without saving the modification 10 Save Save the settings and exit submenu 3 3 9 DEFAULT SETTING Cancel Cancel and exit the sub menu Enter Perform the defaulted setting and exit the sub menu 4 TROUBLESHOOTING 4 1 TROUBLE SHOOTING TABLE Phenomenon Possible Cause Countermeasures Power damage or insufficient Change it No action or image after B Error connection of power Correct it Faults of engineering route Eliminate it Mechanical fault Inspect it electrifying image exists but with motor noise Change the power complying with Insufficient power supply the requirements and put the switch power near th
7. e dome Normal self inspection but no eee Poor video line connection Eliminate it image 16 502775 Operating Manual Phenomenon Possible Cause Countermeasures Normal self inspection but no image Poor video line connection Error connection of control Correct it signal line Unmatched dome address Select it again Successful self inspection but out of control Unmatched protocol or Adjust the protocol or controller to communication Baud rate make it match and electrify again Too far distance and too large Wire diameter in twisted pair or delay of 485 signal thicker control line Poor video line connection Eliminate it Unstable image If several domes are connected in one line central power supply AC24V power connector of dome shall be connected according to the same direction The video picture on the Dome power 1 Incorrect camera phase monitor rolls vertically in position switching process Dome power 2 Dome power 3 17
8. fore moving or re installing this equipment please be sure that the power is shut off 3 This equipment shall be installed at the site with good ventilation 4 In case that this equipment does not work normally please contact supplier and do not disassemble or reform this equipment Xvision will not take any responsibility for the problem resulted from unapproved reformation or repair 5 During cleaning the surfaces of this equipment do not use chemical cleaning agent which may result in the deformation of equipment surface or damage of covering layer 6 It is important that the dome camera is not left in a position where the camera is pointing directly at the sun or other extremely bright light source This may result in CCD damage and poor image quality A 6 Avision XSD27ZS Operating Manual 1 OVERVIEW 1 1 BRIEF INTRODUCTION AND APPLICATION As a high end monitoring product the integrated smart high speed dome camera features strong stable and reliable function easy operation and installation etc It has a good cost performance and has become the mainstream product in monitoring industry This camera has many functions such as fast trace 360 unlimited rotation 180 automatic overturn areas can preset location scan pattern scan screen menu etc The remote head is driven by a stable and reliable step motor that has several speeds The camera is designed to watch a moving target in a large area and
9. ing Using special preset location order Setting of the left boundary dome is controlled to ideal position and preset location 44 is called to set the left boundary of Region 1 Setting of the right boundary dome is controlled to ideal position and preset location 45 is called to set the right boundary of Region 1 Using keyboard for setting Menu set gt scan set gt area scanning Setting of the left boundary control the dome to ideal position and press OPEN key to set the left boundary or Region 1 Setting of the right boundary control the dome to ideal position and press OPEN key to set the right boundary of Region 1 4 area scanning can be set and the method is the same Setting of scanning speed see menu set gt auxiliary set Setting of regional title see menu set gt title set Operating area scanning Call the preset location 52 55 to operate area scanning path 1 4 respectively Dome rotates between the set right and left boundary according to the set speed and the screen displays the corresponding regional title PATTERN SCANNING Setting of pattern scanning 1 Call preset location 56 to start setting pattern scanning 2 Operate up down left right WIDE TELE NEAR FAR CLOSE and OPEN on the dome 3 Call preset location 57 60 to save the 1 4 pattern scanning Operation of pattern scanning Call the preset location 61 64 to operate pattern scanning path1 4 respectively 12 4 ae
10. larming setting Defaulted Setting Recovery the defaulted setting of the dome ON OU b N Exit Exit the main menu SYSTEM INFORMATION 1 Version No The version number of the dome fixed ware 2 Address Dome address to be set by dial switch 3 Communication Communication Baud rate 4 Protocol Communication protocol PELCO D 13 XSD27ZS Operating Manual 3 3 4 3 3 5 5 Camera Display the movement type of camera 6 Date of Manufacture August 2012 7 Manufacturer Xvision 8 Exit Exit the sub menu of system information CAMERA SETTING 1 Zoom Speed Fast medium and slow 2 Digital Zoom On and off 3 White Balance Automatic 4 R gain 1 225 white balance manually effective 5 B gain 0 225 white balance manually effective 6 Exposure Setting 0 7 7 Backlight Compensation On and off 8 Image Freezing On and off 9 Wide Dynamic Mode Automatic off and manual 10 Wide Dynamic Level 0 128 wide dynamic manually effective 11 Image Mirror On and off 12 Colour to black setting Automatic on and off 13 Image Effect Off inverse colour and white band black 14 Image Rollover On and off 15 Camera Display On and off 16 Minimum Focus 1cm 10cm 30cm and 100cm 17 Save Save the settings and exit sub menu 18 Exit Exit the sub menu without saving the modification AUXILIARY SETTING 1 Area Scanning Speed Fast medium and slow 2 Manual Rotation Speed Fast medium and
11. of dome can be set in three ways m Address Dial Switch when the soft address is closed the dome address will be determined by the dial switch Soft Address After the Soft address option is opened the address dial switch will not work The default soft address will also be closed Broadcasting Address the fixed broadcasting address of dome if 100 no matter how the dome address is set key DVR is able to control the dome through 100 addresses XYZ XSD2725 Operating Manual Comparison list of address dial switch mere PP 5 EEA wi Ww XYZ XSD2725 Operating Manual 3 OPERATION INSTRUCTION 3 1 MAPPING TABLE FOR PRESET LOCATION f qvision XSD27ZS Operating Manual 58 CALL Saving the setting of the third group of pattern scanning 59 CALL Saving the setting of the third group of pattern scanning 60 CALL Saving the setting of the third group of pattern scanning 67 CALL Arming of alarming input 1 for the machines with this function only 68 CALL Arming of alarming input 2 for the machines with this function only 69 CALL Disarming of alarming input 1 for the machines with this function only 70 CALL Disarming of alarming input 2 for the machines with this function only 71 CALL Starting alarming output for the machines with this function only 72 CALL Closing alarming output for the machines with this function only 81 CALL Starting the privacy
12. shelter grid for the machines with this function only 502775 Operating Manual 82 CALL Closing the privacy shelter grid for the machines with this function only 83 CALL Starting backlight compensation for the movement with this function only 84 CALL Closing backlight compensation for the movement with this function only 85 CALL Starting image freezing function for the movement with this function only 86 CALL Closing image freezing function for the movement with this function only 87 CALL Starting image mirror function for the movement with this function only 88 CALL Closing image mirror function for the movement with this function only 89 CALL Automatic color to black function for the movement with this function only 90 CALL Starting color to black function for the movement with this function only 91 CALL Closing color to black function for the movement with this function only 92 CALL Closing wide dynamic for the movement with this function only 93 CALL Automatic wide dynamic for the movement with this function only 94 CALL Manual wide dynamic for the movement with this function only 95 CALL Entering the main menu 97 CALL Starting image rollover for the movement with this function only 98 CALL Closing image rollover for the movement with this function only 101 CALL Defaulted setting 102 CALL Switch manual operation speed fast slow and medium BA A a TM vision XSD
13. slow 3 Guarding Position Preset location 0 225 O closing the guard position 4 Recall Time Set the time for automatic recall and duration when it will not be controlled or return to the guard position time 0 225s 5 Vertical Automatic Rollover Dome 180 automatic rollover on off 6 Setting of Status Bar On and Off 14 BA A a 6 evision XSD27ZS Operating Manual 7 Language Setting English and Chinese 8 Soft Address On and Off On and Off 9 Soft Address 001 255 10 Exit Exit the sub menu without saving the modification 11 Save Save the settings and exit sub menu 3 3 6 SCANNING SET 1 Setting of Area Scanning Region No 0 4 2 Operating Area Scanning Region No 0 4 O means the scanning without linking area scanning number 3 Setting Presetting Scanning Preset location No 0 225 4 Operating Presetting Scanning Preset location No 0 225 0 means the scanning without linking presetting 5 Setting of Mode Scanning Mode No 0 4 6 Operating Mode Scanning Mode No 0 4 7 Exit Exit the sub menu without saving the modification 3 3 7 TITLE SET Region No 1 4 X Co Ordinates X position of title on the screen 0 29 Y Co Ordinates Y position of title on the screen 0 14 a The title content in the current region To change move left and right and select characters Move down to confirm changes or move up to exit this option 5 Mode Input method mode capitalized
Download Pdf Manuals
Related Search