User`s Manual
Contents
1. 50 ee s rs 8 12 panda Il manual doc REMOTE CONTROLLER MODE The optional remote controller is used in Master Slave mode When you insert the remote controller s plug into the master s AUDIO socket as shown in the following figure you may control all projectors for shutter open STAND BY button slow fast strobe movment STROBE button and slow fast action to respond to music SLOW FAST button G TERMINATOR f DMX OUT DMX i ES DMX j DMX OUT MASTER SLAVE SLAVE STAND BY STROBE SLOW FAST MAINTENANCE If the projectors lens becomes damaged or broken it should be replaced If the lamp becomes damaged or deformed in any way it must be replaced If the light from the lamp appears dim this would normally indicate that it is reaching the end of its life and it should be changed at once old lamps run to the extremity of their life can explode If the projector does not function check the fuses on the power socket of the projector they should only be replaced by fuses of the same specified value 4A 250V fast blow 5mmx20mm On the main PCB inside the projector there is also a fuse rated 4A 250V fast blow 5mmx20mm Should these be damaged call a qualified technician before replacement The projector has thermal protection device that will switch off the projector in case of overheating should either of these operate check that the fans are not blocked and if they are dirty2. Avoid direct exposure to the light from the lamp The light is harmful to the eye Do not attempt to dismantle and or modify the projector in any way Electrical connection must only be carried out by qualified personnel Before installation ensure that the voltage and frequency of power supply match the power requirements of the projector It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards Do not connect this device to any dimmer pack Make sure that the power cord is never crimped or damaged by sharp edges Never let the power cord come into contact with other cables Only handle the power cord by the plug Never pull out the plug by tugging the power cord Never run the projector without a lamp There are no user serviceable parts inside the projector do not open the housing and never operate the projector with the covers removed Do not use any organic solvent e g alcohol to clean the lenses dichroic colour filters anti heating glass reflector mirror or housing of the projector Always disconnect from the mains when the device is not in use or before cleaning it or before attempting any maintenance work If you have any questions don t hesitate to consult your dealer 3 12 panda 1 manual doc INSTALLING THE PROJECTOR DMX512 OUTPUT EID DMX512 INPUT INNER BRACKET OUTER BRACKET AUDIO SOCKET COOLING FAN
3. Little rectangle Red green yellow and blue 11 Multi quadrangle Green and pink GOBO 12 4 bar Yellow GOBO 13 Sunflower Red GOBO 14 Pentacle Rotation from slow to fast 2 PAN Pan movement from 0 to 175 3 TILT Tilt movement from 0 to 80 4 DIMMER 0 255 Lamp brightness adjust from dark to bright 7 12 panda 1 manual doc TABLE OF DIP SWITCHES SETTING Each projector must be given a DMX start address so that the correct projector responds to the correct control signals The following table lists the setting codes of the address of the DIP switches and the luminaires are from No 1 to No 256 Each luminaire has 10 DIP switches with the numbers of 1 2 3 4 5 6 7 8 9 and 10 For the PANDA II PR 2100B set all 10 switches on the OFF In the table O means the switch is on the OFF and 1 on the ON For example if you want to look up the address setting of the No 50 luminaire you will find the NO 50 luminaire row 1 2 3 4 5 with the codes of 1 0 1 0 0 and column 6 7 8 9 with the codes of 0 1 1 0 So set the 1 3 7 and 8 switches on the ON and set the 2 4 5 6 9 and 10 switches on the OFF Table of DIP 9 0 0 0 0 1 Switches Setting 8 0 0 0 0 1 1 1 7 4 3e lE dE 78 86 94 110211101118 126 URP NN AE
4. 3 GRAY WHITE WHITE YELLOW ORANGE ORANGE GREEN RED RED RED BROWN BROWN ORANGE YELLOW YELLOW e e e S2 S3 DIP SW DMXIN DMX OUT MAIN PCB i Bul b uz FUSE 4A 250V D U3 J IC1 te MAIN PCB US BRIDGE 11 12 panda Il manual doc COMPONENT ORDER CODES NAME PART NO REMARK TRANSFORMER 040050003 230V50Hz 120V60Hz THERMOSTAT 190010054 95 C 10A FAN 030060008 DC12V LAMP 100040051 EFR 15V 150W RELAY 192010018 BRIDGE 150050012 8A 1000V COLOR GOBO MOTOR1 030040051 42BYGHO036 10A MIRROR PAN MOTOR2 030040050 42BYGH036 09A MIRROR TILT MOTOR3 OPTICAL COUPLE 171000008 MOC3022 IC1 230040119 MICROPROCESSOR U1 U3 170110002 DRIVER CHIPS U4 170170034 RESET CHIP U5 230040087 SPECIAL CHIP U6 170170032 BUS CHIP FOR RECEIVING TRANSMITTING U7 170040001 TTL CHIP U8 170050002 ARITHMETIC AMPLIFIER CHIP PR LIGHTING LTD 571 Yingbin Road Dashi Panyu Guangzhou 511430 China TEL 86 20 8478 1888 FAX 86 20 8478 6023 12 12 P N 321010024 Last Revision 17 08 2002 panda 1 manual doc
5. INT om E OUT zc at m OUT IN OUT AUDIO IN OUT AUDIO IN OUT AUDIO fol L 12 0 Ol In the Master Slave mode the programmes having been set in the master may be actived by sound via the MIC inside the master and all projectors will change colours and gobos synchronously according to the rhythm of music 6 12 panda Il manual doc CONTROLLER MODE DMX 512 OPERATION CONNECTING CONTROLLER WITH PROJECTORS Connect the controller s output to the first projector s input and connect the first projector s output to the second projectors input The rest may be deduced by analogy Eventually connect the last fixture s output to a DMX terminator as shown in the figure below DMX 512 CONTROLLER AC NA Af NA f9 f9 e DMX IN No 1 No 2 No n DMX 512 CONTROL CHANNEL FUNCTIONS PANDA II has 4 channels which may be actived by sound via MIC inside the projector or be separately controlled by the controller They are listed in the following table CHANNEL DMX VALUE DESCRIPTION Black out White Strobe adjust from slow to fast White Clear 79 86 Light blue GOBO 1 Circle Pink GOBO 2 Little Circle Blue and yellow GOBO 3 Ring Light green GOBO 4 8 Circle 1 Ultraviolet GOBO 5 4 Sector Violet GOBO 6 3 Bar COLOUR GOBO Light red GOBO 7 Swirl Green GOBO 8 Crisscross 143 150 Light yellow 9 Multi circle Blue GOBO 10
6. N C Pin 4 N C Pin 5 N C Pin 5 N C DMX TERMINATOR In the Controller mode or Master Slave mode the DMX output has to be connected with a DMX terminator at the last fixture in the chain This prevents electrical noise from disturbing and corrupting the DMX control signals The DMX terminator is simply connector with a 1200 ohm resistor connected across pins 2 and 3 which is then plugged into the output socket on the last projector in the chain The connections are illustrated below DMX TERMINATOR Pd CONNECTION Connect a 120 O OHM resistor DESEAN across pins 2 and 3 in an XLR plug and insert into the DMX out socket on the last unit in the chain PIN 2 PIN 3 MASTER SLAVE SYNCHRO MODE Without using the controller many projectors can run synchronously by linking them with each other in the Master Slave mode Select one projector as the master without connecting any cable to the projector s input and set the DIP switches at random Regard the other projectors as the slaves and set all No 1 DIP switches on the ON and the SLAVES other DIP switches on the OFF Connect the master s output to the first slave s input and connect the first slave s output to the second slave s input The rest may be deduced by analogy Eventually connect the last slaves 234506789 10 output to a DMX terminator as shown in the figure below MASTER SLAVE SLAVE E a E Kes E X3 TERMINATOR
7. clean them before switching on the projector again Check that the fans are operational if not call a qualified technician Any maintenance work should only be carried out by qualified technicians KEEPING THE PROJECTOR CLEAN To ensure the reliability of the projector it should be kept clean It is recommended that the fans should be cleaned every 15 days The lens and dichroic colour filters should also be regularly cleaned to maintain an optimum light output Do NOT use any type of solvent on dichroic colour filters Cleaning frequency depends on the environment in which the fixture operates damp smoke or particularly dirty surroundings can cause greater accumulation of dirt on the unit s optics A soft cloth and typical glass cleaning products should be used in cleaning It is recommended to clean the external optics at least once every 20 days and clean the internal optics at least once every 30 60 days Do not use any organic solvent e g alcohol to clean the lenses dichroic colour filters anti heating glass reflector mirror or housing of the projector 9 12 panda 1 manual doc TROUBLESHOOTING PROBLEM RESOURCE The projector does not start Check the fuse on the socket is blown or not Check if the lamp is good or not The projector switches on but does not Check setting the DIP switch is correct answer to commands Check the XLR cable is good The projector only functions Check the fan is working and not dirty intermitte
8. Il manual doc POWER SUPPLY MAINS Use the plug provided to connect the FUSE 4A 250V mains power to the projector Paying attention to the voltage and frequency marked on the panel of the projector It is recommended that each projector is Green Yellow supplied separately so that they may be N Blue individually switched on and off It is recommended that the projector must be earthed correctly and the power convertor must be L switched in the correct position PA N L Brown FUSE HOLDER OPERATION The projector may be operated in Stand Alone mode or be linked with each other for multi units for Master Slave synchro mode or be controlled via standard DMX512 by a controller And even you may use a remote controller to operate the projectors for shutter strobe and fast slow control When the power is on the projector will run self test programmes After finishing these the projector is ready for operation TO SET THE DIP SWITCHES The 10 DIP switches of the PANDA II are with the numbers from 1 to 10 which may be set on the ON or OFF position In Stand Alone mode the DIP switches may be set at random But in Master Slave synchro mode and Controller mode you should set the DIP switches correctly How to set the DIP switches please refer to Controller mode and Master Slave synchro mode STAND ALONE MODE Without connecting a controller with the projector the projector will run in Stand Al
9. MANUAL FOCUS VM POWER 3 7 CONVERTER x M8 KNOB HANGING SITTING There are two ways to install the projector either hanging the projector from the ceiling or sitting on the floor Mount the inner and outer brackets provided on the body of the projector There are 2 M8 knobs provided to tighten the body of the projector and the two brackets When you want to adjust the angle of the body of the projector you only loosen the two M8 knobs carefully and then adjust the angle of the body After finishing that it is recommended that you don t forget to retighten the two M8 knobs Always ensure that the projector is firmly positioned to avoid vibration and slipping For suspending the projector always ensure that the structure to which you are attaching the projector is secure and is able to support a weight of 6kg for each PANDA II FITTING THE LAMP DIRECTION FOR PLUG OR UNPLUG THE LAMP LAMP BRACKET M4 KNURLING SCREW SERINGS LAMP HOLDER LAMP M4 TAPING SCREWS Remove the upper cover by loosening the 2 M4 taping screws and 1 M4 knurling screw Insert an EFR 15V 150W lamp in the lamp porcelain holder When replacing a lamp you should first pull out the old lamp from the lamp bracket Push the lamp into the position seat of the lamp bracket carefully Install the upper cover again Note Do not forget to connect the grounding cord with the upper cover Retighten the 2 M4 screws and 1 M4 knurling screw 412 panda
10. RELIABILITY PANDA Il PR 2100B This product manual contains important information about the safe installation and use of this projector Please read and follow these instructions carefully and keep this manual in a safe place for future reference PR LIGHTING LTD Yingbin Road Dashi Panyu Guangzhou 511430 China http www pr lighting com SECTION PAGE SAFE USAGE OF THE PROJECTOR 3 INSTALLING THE PROJECTOR FITTING THE LAMP POWER SUPPLY MAINS OPERATION STAND ALONE MODE XLR CONNECTORS AND TERMINATOR MASTER SLAVE SYNCHRO MODE CONTROLLER MODE DMX 512 OPERATION REMOTE CONTROLER MODE MAINTENANCE KEEPING THE PROJECTOR CLEAN TROUBLE SHOOTING 10 TECHNICAL DATA 10 ELECTRICAL DIAGRAM 11 SA Please note that as part of our ongoing commitment to continuous product development specifications subject to change without notice Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement The publishers cannot be held responsible for the accuracy of the information herein or any consequence arising from them Every apparatus is tested completely and packed properly by the manufacturer Please make sure the packing and or the apparatus is in good condition before your installation and use Should there be any damage caused by transportation consult your dealer and do not use the apparatus But a
11. glass filters so the producing light beam is bright and sharp PANDA II will switch off the lamp automatically after 8 seconds of shutter so it can effectively prolong the life of the lamp The gobo colour wheel rotating quickly can produce rainbow or strobe effect In addition you may use remote controller with a long distance to control the luminairs for shutter strobe and fast slow action to audio 2 12 panda Il manual doc SAFE USAGE OF THE PROJECTOR The following points are important for safety as well as for the smooth installation and performance of the unit When unpacking and before disposing of the carton check there is no transportation damage before using the projector Should there be any damage caused by transportation consult your dealer and do not use the apparatus The projector is for Indoor use only IP20 Use only in dry locations Keep this device away from rain and moisture excessive heat humidity and dust Do not allow contact with water or any other fluids or metallic objects The projector is not designed or intended to be mounted directly on to inflammable surfaces The projector is only intended for installation operation and maintenance by qualified personnel The projector must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked Do not project the beam onto inflammable surfaces minimum distance is 3m i 3m
12. ntly The beam appears dim Check the lamp is not at the end of its life Check the optics and anti heat glass are clean Carefully clean the lamp the optical group lenses and anti heat glass Check the lenses are not broken Remove dust or grease stored on lenses TECHNICAL DATA 240V 230V 220V 200V 120V 100V AC 50 60Hz To order Projection with halo Defecting projection Power supply Power consumption 180W at 220V Lamp EFR 15V 150W Channels 4 channels Control signal Control mode Running mode Colours Gobos Mirror movement Shutter Strobe Beam angle Net weight Others Standard DMX 512 Sound activation Controller Remote Controller Stand Alone mode Master Slave synchro mode Controller mode 11 one colour 2 double colour 1 four colour white and rainbow effect 14 gobos clear Pan movement 175 Tilt movement 80 Shutter on gobo wheel for blackout and strobe adjustable from 1 7 F P S 14 6 6kg Auto thermal cut off Adjustable lamp brightness Manual adjustable focus Auto switch off the lamp after 8 seconds of shutter 390 145 234 10 12 panda 1 manual doc ELECTRICAL DIAGRAM als TRANSFORMER oN RED 230V COLOUR GOBO MIRROR MIRROR WHEEL PAN TILT MOTOR 1 MOTOR2 MOTOR
13. ny damage caused by improper use will not be assumed by the manufacturer and or dealer ACCESSORIES THESE ITEMS ARE PACKED TOGETHER WITH THE PROJECTOR Inner Bracket 1 PCS Outer Bracket 1 PCS M8 knobs for bracket 2 PCS Power cord 1 PCS XLR plug 1 PCS XLR socket 1 PCS This manual 1 PCS Remote Controller Optional INTRODUCTION Thank you for purchasing our product PANDA II PR 2100B This product manual contains important information about the safe installation and use of this projector Please read and follow these instructions carefully and keep this manual in a safe place for future reference PANDA II adopts advanced procedure of design and manufacturing and uses international protocal DMX 512 and compiles to CE norms The figure of housing is elegant lovable and portable which features its special character compared with conventional luminaire PANDA II can be suspended from the ceiling or be seated on the floor with the inner and outer brackets provided and the angle of the body is easy to be adjusted and the projector even can be carried by hand The programmes having been set in the PANDA II may be actived by sound or controller The PANDA I can be used as a stand alone unit or linked with each other for multi units or linked to a controller so it is suitable for many different applications PANDA II uses an OSRAM 15V 150W lamp with adjustable lamp brightness via controller and uses 14 gobos and 14 colourful
14. one mode with setting the DIP switches at random In Stand Alone mode the programmes having been set may be actived by sound via the MIC inside the projector The projector will change the colours and gobos according to the rhythm of the music XLR CONNECTORS AND TERMINATOR XLR CONNECTORS DMX IN DMX OUT DMX512 2 MN PIN FUNCTION a oS an 2 DATA 3 3 3 DATA Connection between controller and projector and between one projector and another must be made with 2 core screened cable with each core having at least a 0 5mm diameter Connection to and from the projector is via cannon 3 pin XLR plugs and sockets which are included with the projector The XLR s are connected as shown in the figure above Note care should be taken to ensure that none of the connections touch the body of the plug or each other The body of the plug is not connected in any way The PANDA II accepts digital control signals in standard DMX512 1990 format 5 12 panda 1 manual doc 5 PIN AND 3 PIN CONVERSION PANDA uses 3 pin XLR plug socket If your controller uses 5 XLR plug socket you should convert 5 pin plug socket into 3 pin socket plug as shown below 5 PIN SOCKET 3 PIN PLUG 5 PIN PLUG 3 PIN SOCKET Pin 1 GND SCREEN Pin 1 GND SCREEN Pin 1 GND SCREEN Pin 1 GND SCREEN Pin 2 Signal Pin 2 Signal Pin 2 Signal Pin 2 Signal Pin 3 Signal Pin 3 Signal Pin 3 Signal Pin 3 Signal Pin 4
Download Pdf Manuals
Related Search