5913 Bluetooth Module User Manual
Contents
1. e When connecting to COM3 on the SCADAPack 350 jumpers J15 and J16 must be in the Normal position Use the RJ 45 to RJ 45 cable part number 297303 e Use the RJ 45 to RJ 45 cable part number 297303 SCADAPack 32 e When connecting to COM1 on the SCADAPack 32 jumper J4 Com Port 5V must be connected And jumper J10 must be in the RS 232 position e When connecting to COM2 on the SCADAPack 32 jumper J4 Com Port 5V must be connected e When connecting to COM4 on the SCADAPack 32 jumper J4 Com Port 5V must be connected 5601 and 5602 I O Modules e The 5913 may be connected to COM3 e Use the RJ 45 to DE9S cable part number 297304 5604 I O Module e The 5913 may be connected to COM3 e Use the RJ 45 to RJ 45 cable part number 297303 4 2 5913 Serial Port Connections The following diagram shows the pin connections for the RS 232 RJ 45 Modular Jack port connector for the 5913 RJ 45 Modular Jack SE Oe ON ay x lt SG e7 lels lasle li Figure 1 RJ 45 Connector Pinout 1 5V Input 5V supplied by the SCADAPack controller System ground 5 RxD Input 0 to 5V signal levels e 0 Output 5913 and 5914 User and Reference Manual 15 April 30 2008 Fin Raneton Dessrpion O CT Toon signal levels 4 3 Serial Port Communication Parameters The serial port on the 5913 module is set for 9600 baud 8 data bits no parity and 1 stop bit at the factory These setting may be viewed or changed using2. e Configure applications such as TelePACE and RealFLO to use the Bluetooth connection 3 1 Install 5913 Serial Adaptor The installation of the 5913 involves making a serial cable connection to a SCADAPack controller There are two types of serial connector used on SCADAPack products RJ 45 and DE9S Both serial cable types are shipped with the 5913 For further details on the cables and SCADAPack controller serial ports see section 4 1 5913 Installation 3 2 Install 5914 USB Adaptor The 5914 USB is installed by plugging the unit into an available USB slot on your PC When properly connected to a USB port the blue indicator led on the 5914 USB Bluetooth will be on 3 3 Install 5914 USB Adapter Software Driver The software driver is installed from the CD ROM that came with the 5914 This CD contains the WIDCOMM Bluetooth Software The installation will automatically start and open the Setup Program splash screen Note The 5914 is NOT supported on Windows Server 2003 operating system 5913 and 5914 User and Reference Manual 5 April 30 2008 e Click the Next button to start the Installation Wizard The Installation Wizard will guide you through the installation i WIDCOMM Bluetooth Software 5 1 0 1700 Welcome to the InstallShield Wizard for WIDCOMM Bluetooth Software 5 1 0 1700 The InstallShield R Wizard will install WIDCOMM Bluetooth Software G 1 0 1200 on your computer To continue click Next WARNING Thi
3. cxce vaccines coccaneateceencictienerinteenciatienerintientien 16 4 5 5914 Connection ccccccccccccccccceececeeeeeeeeeceeecceeeecececeeeceeeeeeeceeseseeeeeeeess 16 5 MAIN TENANGE eege aa aa aa ra a a ea a iaar aia 17 6 Jda eieiei LE 18 6 1 AE DEE 18 6 1 1 SEENEN 18 6 1 2 COMIMUMCATIONS eet dee hones e gege gege gue 18 6 1 3 Power Supplies and Power Consumption nnnnnnnnnnnnnnnnnnnnnnnnnnnnna 18 6 1 4 Approvals and Certifications wi oo ties bee eee ene ee 18 6 2 AE E 19 6 2 1 ELLE 19 6 2 2 EENEG 19 April 30 2008 1 Overview Bluetooth is a global standard communications method that enables data to be exchanged wirelessly between electronic devices The products described in this user manual the 5913 Bluetooth adaptor and the 5914 USB Bluetooth are designed to provide wireless connection between SCADAPack controllers and PCs This wireless connection replaces direct serial connections which are difficult to create in many field installations The 5913 connects directly to a serial port on a SCADAPack controller using one of the two serial cables that are available Operating power for the 5913 is provided by the serial port on the SCADAPack controller The 5913 is shipped from the factory as a discoverable Bluetooth slave device The 5914 is a Universal Serial Bus USB Bluetooth transceiver Operating power is provided through the USB interface The 5914 is shipped with a CD containing the Bluetooth USB Adapter Softwa
4. APack controller The connection description for SCADAPack controllers and integrated I O boards are listed below SCADAPack and Micro16 Controllers e The 5913 may be connected to RS 232 ports COM1 or COM e Use the RJ 45 to DE9S cable part number 297304 SCADAPack LP e When connecting to COM 2 on the SCADAPack LP jumper J13 must be connected e The 5913 may be connected to COM3 e Use the RJ 45 to RJ 45 cable part number 297303 SCADAPack 100 e When connecting to COM1 on the SCADAPack 100 jumper J5 must be connected e When connecting to COM2 on the SCADAPack 100 jumper J6 must be connected e Use the RJ 45 to RJ 45 cable part number 297303 SCADAPack 330 334 e When connecting to COM1 on the SCADAPack 330 jumper J8 must be in the RS 232 position and jumper J7 must be in the 5V position Use the RJ 45 to RJ 45 cable part number 297303 e When connecting to COM2 on the SCADAPack 330 jumper J10 must be in the RS 232 position and jumper J7 must be in the 5V position Use the RJ 45 to RJ 45 cable part number 297303 e When connecting to COM3 on the SCADAPack 330 jumpers J11 and J12 must be in the Normal position Use the RJ 45 to RJ 45 cable part number 297303 e Use the RJ 45 to RJ 45 cable part number 297303 SCADAPack 350 e When connecting to COM2 on the SCADAPack 350 jumper J13 must be in the RS 232 position Use the RJ 45 to RJ 45 cable part number 297303 5913 and 5914 User and Reference Manual 14 April 30 2008
5. Control Microsystems Bluetooth User Manual Model 5913 Bluetooth Adaptor type RJ 45 Controller Model 5914 USB PC Bluetooth CONTROL MICROSYSTEMS SCADA products forthe distance 48 Steacie Drive Telephone 613 591 1943 Kanata Ontario Facsimile 613 591 1022 K2K 2A9 Technical Support 888 226 6876 Canada 888 2CONTROL 5913 and 5914 User and Reference Manual 2007 Control Microsystems Inc All rights reserved Printed in Canada Trademarks TeleSAFE TelePACE SmartWIRE SCADAPack TeleSAFE Micro16 and TeleBUS are registered trademarks of Control Microsystems Inc All other product names are copyright and registered trademarks or trade names of their respective owners 5913 and 5914 User and Reference Manual 1 April 30 2008 Table of Contents 1 OVERVIEW EE 3 2 IMPORTANT SAFETY INFORMATION sssseesceeeeeeeesseeesseseeeeeeeeeeneees 4 3 QUICK START GUIDE E 5 3 1 Install 5913 Serial Ad TEE 5 3 2 Install 5914 USB Adaptor E 5 3 3 Install 5914 USB Adapter Software Drver 5 3 4 Configure Bluetooth Connechon 7 3 5 Configure Internal Laptop Bluetooth Connecthon 12 3 6 Configure APPIICATION science trenton seek a ton te Sen Gat Saab ate 12 4 INSTALLATION EE 14 4 1 REN EE e EE 14 4 2 5913 Serial Port Connections nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn rnnr rnern eneee 15 4 3 Serial Port Communication Parameters cccccccccccccceecceeeeeeeeeeeeeeees 16 4 4 5913 Dimensions and LEDS sc
6. Control Microsystems Inc Modbus Communication Settings Addressing Standard x Station 1 Timeout 3 seconds Attempts 3 M Serial Port Settings Pot z Baud EE Parity Noe i sl Stop Bits hi sl Connection Type Direct Connection Restore Defaults The factory default serial settings for the 5913 are 9600 baud 8 data bits no parity and 1 stop bit COM4 is the virtual serial port created during the installation of the 5914 USB software driver Note Bluetooth connections will be disconnected if an attempt to create a New Connection is made when the 5913 is connected 5913 and 5914 User and Reference Manual 13 April 30 2008 4 Installation 4 1 5913 Installation The installation of the 5913 involves making a serial connection to a SCADAPack controller The 5913 has a single RJ 45 serial connector as shown in Figure 2 5913 Depending on the SCADAPack controller you are connecting to use one of the two serial cables available to connect the 5913 to the SCADAPack Note The 5913 is supplied with serial cable RJ 45 to RJ 45 CMI part number 297303 Cable RJ 45 to DE9S CMI part number 297304 may be ordered separately These cables are two feet long and must not be substituted with longer cables Longer cables have the potential to introduce noise on the serial port and result in very poor communications The 5913 is powered through the serial port when connected to a SCAD
7. accordance with Class I Division 2 wiring methods Article 501 4 b of the National Electrical Code NFPA 70 for installations in the U S or as specified in Section 18 1J2 of the Canadian Electrical Code for installations within Canada and in accordance with the authority having jurisdiction WARNING EXPLOSION HAZARD SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS 1 DIVISION 2 WARNING EXPLOSION HAZARD WHEN IN HAZARDOUS LOCATIONS TURN OFF POWER BEFORE REPLACING OR WIRING MODULES WARNING EXPLOSION HAZARD DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NONHAZARDOUS 5913 and 5914 User and Reference Manual April 30 2008 3 Quick Start Guide This section of the manual will lead you through the steps necessary to establish a Bluetooth connection between your PC and a target controller PC applications such as RealFLO TelePACE and ISaGRAF will then be able to use the Bluetooth connection in a similar manner as a direct serial connection Note If you are using a laptop with a built in Bluetooth adapter you do not need to install the 5914 USB Adapter software driver The Quick Start procedure includes the following items e Install 5913 module at the SCADAPack e Install 5914 USB e Install 5914 USB Adapter Software Driver e Establish Bluetooth Connection between 5913 and 5914 e Establish Bluetooth Connection using internal Bluetooth on laptop
8. dentification and Error Correction Frequency 2 402 to 2 48 GHz ISM 2 4GHz band Channels 79 at 1MHz intervals Distance Class 1 100m 330 ft NOTE When the 5913 is used with a Bluetooth device that is Class 2 the maximum distance achieved will be approximately 3m or 10 ft Class 2 Receive Sensitivity 83dBm typical Transmit Power 12dBm max software adjustable Antenna Integrated chip antenna Host side TxD and RxD implemented 6 1 3 Power Supplies and Power Consumption Voltage 5V supplied by the controller Requirements Pin 9 on the 5913 D Pin 1 on 5913 J Current 80mA transmit Requirements 40mA receive 1 4mA idle mode 30uA deep sleep 120mA worst case peak 6 1 4 Approvals and Certifications Electrical Equipment for Use in Class I Division 2 Groups A B C and D Hazardous Locations C CSA us Temperature Code T5 Digital Emissions FCC 47 CFR Part 15 Subpart B Class A Verification EN61000 6 4 2001 Electromagnetic Compatibilit 5913 and 5914 User and Reference Manual 18 April 30 2008 Immunity Declaration 6 2 5914 6 2 1 General Terminations and Mounting Dimensions Environment Generic Emission Standard Part 6 4 Industrial Environment EN61000 6 2 2001 Electromagnetic Compatibility Generic Standards Part 6 2 Immunity for Industrial Environments This product conforms to the above Emissions and Immunity Standards and therefore conforms with the requirements of Council Dir
9. ective 89 336 EEC as amended relating to electromagnetic compatibility and is eligible to bear the CE mark The Low Voltage Directive is not applicable to this product USB Connection 1 8 inch 47 mm 0 67 inch 17 mm 0 33 inch 8 5 mm 0 C to 50 C 32 F to 122 F operation 20 C to 70 C 4 F to 158 F storage 6 2 2 Communications General Frequency Radio modem compatible with Bluetooth enabled devices Frequency Hopping Spread Spectrum Encryption PIN identification and Error Correction 2 402 to 2 48 GHz ISM 2 4GHz band Channels 79 at 1MHz intervals Distance Receive Sensitivity Class 1 100m 330 ft lt 0 1 BER at 70dBm typical Transmit Power Class 1 Antenna 5913 and 5914 User and Reference Manual April 30 2008 Printed antenna
10. h Device Selection Select a device Remote devices must be in Discoverable mode for this computer to find them For assistance in making a remote device discoverable refer to the remote device s documentation Cancel Search Show all devices Searching for Bluetooth devices in the neighborhood please wait Cancel e Enter the Bluetooth security code and click the Pair Now button Security Code default Bluetooth Security Setup Bluetooth Pairing Paired devices exchange a secret key each time they connect This key is unique for each pair of devices it is used to verify identity and to encrypt the data that the devices exchange To pair with the selected device you must know that device s security code If the selected device does not require a security code or to pair with the device later click Skip Pair Now Enter the security code and then click Pair Now Bluetooth security code e Select the virtual serial connection and click the Configure button 5913 and 5914 User and Reference Manual April 30 2008 Bluetooth Service Selection Select the services you are interested in The following services are available through the selected Bluetooth Device Select the service that you want to access on the selected device Connect to this service como Establish a virtual serial port connection with a remote Bluetooth device The connection can then be used by a
11. laptop or PC has an internal Bluetooth adapter you can use it to establish a Bluetooth connection with the 5913 Refer to your user manual for details on establishing a Bluetooth connection Note Ifthe 5913 is used with a laptop using a built in class 2 Bluetooth device the range will be limited by the class 2 device approximately 3m or 10 ft The internal Bluetooth may not be set up for automatic discovery This needs to be enabled in your configuration software An example of the correct setting is shown in the figure below Bluetooth Configuration General Accessibility Discovery Local Services Client Applications Diagnostics Select specific devices classes of devices or types of devices within a athe class that this computer should discover and report Look for other Bluetooth devices Every 10 minutes R eport all Bluetooth devices v Filter Type Details Device CMIWKS9 3 6 Configure application All Control Microsystems software applications may be configured to use a Bluetooth connection to communicate with a target SCADAPack controller Communication parameters for the communication link between a PC and A SCADAPack controller are set using the PC Communication Setting dialog The PC Communication dialog for RealFLO is shown below 5913 and 5914 User and Reference Manual 12 April 30 2008 Modbus RTU Configuration General Advanced Information Communication Component Modbus ATU
12. ny application that supports the COM port number assigned e The COM Port selected will be the virtual serial connection on the computer Note that this is the port you will need to select when setting the PC Communication Settings in your application Bluetooth Properties General Ka 5056457 COMO Secure Connection COM Port MUGES e Click the Finish button to complete the Bluetooth Setup wizard 5913 and 5914 User and Reference Manual April 30 2008 10 Bluetooth Setup Wizard Completion Page Completing Bluetooth Setup Wizard 5056457 COMO shortcut Ka Connect to the remote device using this connection oO Create a shortcut and then restart this wizard so that can create additional shortcuts To complete this connection click Finish e The Bluetooth connection is now ready for applications My Bluetooth Places File Edit View Bluetooth Favorites Tools Help Bach Ka P Search 1 Folders Address My Bluetooth Places 5056457 Bluetooth Tasks 6 Add a Bluetooth Device 5056457 COMO SW View My Bluetooth services connected EON gt View devices in range g View or modify configuration Other Places Ej Desktop d My Computer Bluetooth Exchange Folder K My Network Places QY Printers and Faxes 5913 and 5914 User and Reference Manual April 30 2008 3 5 Configure Internal Laptop Bluetooth Connection If your
13. ou want the icon to appear and click Next Add the icon to the Programs menu Add the icon to My Computer e When prompted with the Bluetooth Service Selection you must select Bluetooth Serial Port to allow remote Bluetooth devices to connect to the computer 5913 and 5914 User and Reference Manual 7 April 30 2008 Bluetooth Service Selection Choose the services that this computer will offer To enable a service place a check in the box next to the service name To display the properties panel for a service click Configure KS PIM Item Transfer O PM synchronization Cla File Transfer CIS Network Access CIS Dial up Networking Bluetooth Serial Port Allow remote Bluetooth devices to connect to this computer via a wireless serial port a e Click the Next button to configure any active Bluetooth devices or click the Skip button to setup the connections later Initial Bluetooth Configuration Wizard Initial Bluetooth Configuration Wizard This wizard can help you setup connections to Bluetooth computers phones headsets etc To setup a connection now put the other device in pairing mode and then click Next See the other device s documentation for assistance in preparing it to accept a connection To setup connections later click Skip e Select the device you would like to configure and click the Next button 5913 and 5914 User and Reference Manual April 30 2008 Bluetoot
14. re Driver The 5914 connects to a PC or laptop and operates as a Bluetooth master when communicating with the 5913 While this user manual describes the configuration and operation of 5913 in conjunction with the 5914 the 5913 may be used with any compatible Bluetooth device such as an internal Bluetooth transceiver on a PC or laptop The features of the 5913 include e Wireless communications module certified to Bluetooth ver2 0 e Integrated software stack profiles and AT modem like commands e The 5913 can be configured and controlled through simple ASCII strings over the Bluetooth RF link e Serial port UART baud rate speeds 1200bps up to 921 6Kbps e Bluetooth Class 1 100 meter 330 feet distance e Software adjustable transmitter power from short to long range applications e Secure and robust communication link FHSS Frequency Hopping Spread Spectrum encryption and 16 alphanumeric Personal Identification Number PIN and error correction schemes for guaranteed packet delivery Note The 5913 Bluetooth adaptor requires 5VDC for operation The SCADAPack controller supplies this voltage through the serial port This requirement prohibits the Bluetooth adaptors from being used with SCADASense transmitters or any device that does not supply the SVDC through the serial port 5913 and 5914 User and Reference Manual 3 April 30 2008 2 Important Safety Information Power input and output i o wiring must be in
15. s program is protected by copyright law and international treaties e The Bluetooth configuration is now complete You may click Finished and begin to discover the available devices i WIDCOMM Bluetooth Software InstallShield Wizard Completed The InstallShield Wizard has successfully installed WIDCOMM Bluetooth Software Click Finish to exit the wizard Cancel 5913 and 5914 User and Reference Manual 6 April 30 2008 3 4 Configure Bluetooth Connection The My Bluetooth Places Bluetooth Neighborhood can be located in the Windows Start gt gt All Programs gt gt My Bluetooth Places The available devices will automatically discover in the Entire Bluetooth Neighborhood The serial number of the 5913 Serial Adapter is displayed as the device name The adapters listed will be the Bluetooth devices within range approximately 300 feet e Click the Next button to begin the Initial Bluetooth Configuration Wizard The Configuration Wizard will guide you through the configuration process Initial Bluetooth Configuration Wizard Initial Bluetooth Configuration Wizard Before you can begin using Bluetooth on this computer you must perform some initial setup This wizard will help you to configure a basic Bluetooth environment You can access the Bluetooth features on this computer through the Bluetooth icon on the desktop or in the system tray This icon can also appear in the following locations Select the locations y
16. the AT commands described in the 5913 AT Command Appendix 4 4 5913 Dimensions and LEDs The dimensions of the 5913 are shown in Figure 2 5913 below e The Blue LED indicates that a Bluetooth connection is made with another Bluetooth device e The Green LED indicates that the 5913 is powered by a5 VDC source wl 2 024 me L Figure 2 5913 Dimensions 4 5 5914 Connection The 5914 connects directly to a USB port on a laptop or PC The 5914 cannot be connected to the USB ports on SCADAPack 300 Series controllers 5913 and 5914 User and Reference Manual 16 April 30 2008 5 Maintenance This module requires no routine maintenance If the module is not functioning correctly contact Control Microsystems Technical Support for more information and instructions for returning the module for repair 5913 and 5914 User and Reference Manual April 30 2008 17 6 Specifications Disclaimer Control Microsystems reserves the right to change product specifications without notice For more information visit www controlmicrosystems com 6 1 5913 6 1 1 General Terminations 8 pin modular jack Dimensions 2 02 inch 51 mm 1 70 inch 43 mm 0 81 inch 21 mm Mounting Velcro mounting supplied Environment 40 C to 70 C 40 F to 158 F operation and storage 6 1 2 Communications General Radio modem compatible with Bluetooth enabled devices Frequency Hopping Spread Spectrum Encryption PIN i
Download Pdf Manuals
Related Search