Home

User Manual EKI-1331 - download.advantech.com

1. User Manual EKI 1331 Cellular Gateway AD ANTECH Enabling an Intelligent Planet Copyright The documentation and the software included with this product are copyrighted 2015 by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reliable How ever Advantech Co Ltd assumes no responsibility for its use nor for any infringe ments of the rights of third parties which may result from its use Acknowledgements Intel and Pentium are trademarks of Intel Corporation Microsoft Windows and MS DOS are registered trademarks of Microsoft Corp All other product names or trademarks are properties of their respective owners Product Warranty 5 years Advantech warrants to you the original purchaser that each of its products will be free from defects in materials and workmanship for five years from the date of pur chase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech or which have been subject to misuse abuse accident or improper installation Advantech a
2. 51 EKI 1331 User Manual 3 8 7 Log From navigation panel select Status gt gt Log then enter Log page as shown below This page show system log including Download Log File System Network Services Firewall dos Tools Status Log View recent 0 sl Lines Level Time Module Content Too many logs old logs are not displayed Please download log file to check more logs info Jan 1 08 00 08 processor 257 0 protocol info Jani 080008 processori257 0 serermode Client info Jan 1 08 00 08 processor 257 0 diu framevalims 100 info Jan 1 08 00 08 processor 257 0 diu uartframe mum 4 info Jan 08 00 08 processorf257 0 comdev dewtyS1 info Jan 08 00 08 processorf257 0 115200 8 1 N info Jani 080008 processor257 0 Open fdewtyS1 115200 8 1 N info Aan i 08 00 08 processof257 D IMETU running info Jan 08 00 13 redial 115 moder is started info Jan 08 00 13 redial 1 15 drmar found for EM77 OW info Jani 00 00 13 kamel usbcore registered new interface driver usbserial info Jan 00 00 13 kemel drversiuskisenalusb senal e USB Serial support registered for generic info Jan 00 00 43 kernel usbcore registered new interface driver usbserial_generic info Jan 00 00 13 kemel driversfyusb seriallusb senalc USB Serial Driver core info Jani 08 0044 redialf115 setup AT command sel for usb modem info Jan 08 00 14 redial 115 mram sel want _iface dewty USO info Jan 1 08 00 14 redial 1 15 can not open devttyUSBO info Jan 090014
3. Parameters Description Default Gateway Configuration Import Backup configuration N A Restore default configura Click to reset EKI 1331 To complete the N A tion reset users need to reboot the EKI 1331 The technician must configure the local Network Provider ISP APN username password and other con N A figs the same as their ISP Caution Be sure to check imported configs for incorrect formats and complete ness When importing the system will filter the improperly formatted AN commands and save the correct configuration The good configs will later be serially executed in order after system reboot The system will not get into expected state in the case that the imported configuration is not arranged according to an effective order Caution In order not to affect the operation of the current system when perform ing an import configuration and restore default configuration users need AN to restart the gateway to make the new configuration to take effect EKI 1331 User Manual 20 3 2 7 System Upgrade From the navigation panel select System gt gt Upgrade then enter the Upgrade page as shown below ADNANTECH Enabling an Intelligent Planet System Network Services Firewall dos VPN Tools Status Upgrade Select the file to use STAT FARTHER Upgrade Current Version 12 003558 Current Bootloader Version 1 1 3 12777 To upgrade the system click the System tab then lt System upgrade gt to enter upgr
4. DTU ID Source IP Description Check to enable the DTU Set the DTU protocol Please see more in related Quick Guide TCP and UDP are both options Set the DTU as a client or server Set the frame interval Set the number of serial buffer frames Choose either parallel or poll options Set the minimum reconnect interval Set the maximum reconnect interval Set the ID of the DTU It s only available when using DC protocol Set the Source IP 33 Tools Stalius Default Disable Transparent UDP Client 100 mseconds 4 Parallel 15s 180s N A N A EKI 1331 User Manual 3 45 Modbus to SMS EKI 1331 inquires the variables status of the PLC every ten seconds and saves them into RAM These variables will be the SMS response sent after a query After receiv ing a control SMS EKI 1331 sende the control command to the PLC and waits for a response The response is sent from the PLC and then EKI 1331 sends the response to the user To enable SMS find the navigation panel select Services gt gt Modbus to SMS to enter into the Modbus to SMS page After you add your PLC here the daemon of EKI 1331 periodically queries the PLC variables and cache to memory AD ANTECH Enabling an Intelligent Planet System Network Services Firewall Dos VPN Tools Status Modbus To SMS Enable sg PLG list PLO gd Modbus type RTU e Modbus ID 1 PLC name Register address base 1 Type Units Register name BIT k
5. 20 PLC out None 13310424743 pica AB VOLT OUT of range 219235 Apply Cancel Caution The first rule states that when the OUTPUT of plc2 changes from 1 to 0 or from 0 to 1 trigger the alarm and send the alarm SMS to all users in AN the alarm user list The second rule states that when the variable value of AB_VOLT in plc2 is less than or equal to 20 or greater than or equal to 230 trigger the alarm and send the user define SMS to the user 13810556243 In other words when AB_VOLT is between 20 and 230 plc2 is in normal operat ing conditions EKI 1331 User Manual 38 3 4 7 Mbsms Variable Template 3 4 8 Users can download a PLC variable template file which you might have added in sec tion 3 3 Modbus to SMS A template file is composed of all the variables in a PLC and the EKI 1331 supports up to eight templates To configure the Mbsms template go into the navigation panel select Services gt gt Mbsms Variable Template then enter Variable Template page which is shown below ADNANTECH Enabling an Intelligent Planet system Network Services Firewall dos VEN Too status Mbsms variable template Variable template SMS User can do a status check and reboot the EKI 1331 through SMS After setting a user defined message in the SMS config window users can see the device s status or reboot the device Statistics like signal strength IP address and uptime among others may be used to
6. Advertisement Interval Set an advertisement interval Virtual IP Set a Virtual IP address Authentication Type Choose between None or Password type Virtual MAC Select to enable Marion Select WAN to start monitoring WAN interface EKI 1331 User Manual traffic select None do not monitor 32 Tools Status Default Disable 1 20 bigger num ber stands for higher priority 60 sec N A None Disable None 3 4 4 DTU Serial Port If you connect a serial device to EKI 1331 you need enable the DTU converter EKI 1331 can support a multi protocol uplink to allow conversion of serial data and IP data Users must select the correct serial mode on the window Serial Port from the navigation tab System To enable the DTU go into top navigation panel select Services gt gt DTU then enter DTU page as shown below ADNANTECH Enabling an Infelligent Planet System Network Enable DTU Protocol Protocol Mode Frame Interwal Serial Buffer Frames Mufti Server Policy Min Reconnect Interval Max Reconnect Interval DTU ID Source P Multi Server Server Address Services Firewall os PN DTU Transpareni r UDP T 100 mseconds Parallel 15 Seconds 180 Seconds Server Port The page is described below Parameters Enable DTU Protocol Protocol Mode Frame Interval Serial Buffer Frames Multi Server Policy Min Reconnect interval Max Reconnect interval
7. 3 1 3 2 3 3 3 4 3 5 3 6 AU CITT MOT 2 FEST tease 2 Physical Characteristics A 3 Figure 1 1 DIN Rail Mount 3 Figure 1 2 Wall Mount 3 Login Gateway D Establish Network Connection 6 2 1 1 Automatic Acquisition of IP address 6 2 1 2 Seta Static IP Address i 9 Test the Network Connection between the Supervisory PC and EKI 1331 10 Disconnect from the Proxy Server 11 Configuration rasrrnavenavennvennvennvennvennr 13 Login the Web Configuration Page of Gateway 14 Ee 15 321 Basic SUP 15 5323 I EE 16 323 NN 17 322 PNAS 17 325 SYSIeM LOG EE 19 3 2 6 Config Management 20 32 7 System Me ege 21 32 05 RD 22 GE EE ie e EE 23 NO VOR EEE EE EE ENE 23 3 3 1 Dialup Cellular Connection 23 UN 26 SSC eG DN EE 27 Sd DENSI 28 3 35 Stali e EE 29 TU 30 3 4 1 DHCP SCIVICC E 30 3 4 2 DNS Reali 31 3 4 3 VRRP Virtual Router Redundancy Protocol aanaannannennaanannna 32 344 DTU Serial Port anne a a 33 3 4 5 Modbus KEE 34 3 4 6 SMS Alarm Hues 35 3 4 7 Mbsms Variable Template 39 E pelli 39 SEN EEE EEE 40 JAN BT 40 3 9 2 MENN 41 39 9 PNAN MN 42 3 5 4 Virtual IP Mappmg nenn nenn nenennnennen 43 3 5 5 DMZ All Port Mapping 44 356 MAGHI Bundling Seege ee EE een 44 a EE 45 3 6 1 Bandwidth Control
8. 45 vii EKI 1331 User Manual 3 7 3 8 Chapter 4 4 1 4 2 4 3 4 4 4 5 4 6 4 7 4 8 4 9 Appendix A 1 Appendix B B 1 EKI 1331 User Manual ele EEE EE EE 47 Sen PI 47 3 7 2 Trace ROUte i 48 3 7 3 Link Speed TEE ee eneen Steeg iaia 48 EE 49 SOLL ille 49 3 8 2 0 00 nennen nnnn nen nnnnn nennen nn en nennen 50 3 8 3 Network Connections Rennen ann nn en nme nennen nenn nennen 50 3 8 4 Route Table 51 8959 Device BEEN 51 3 8 6 Modbus PBC 51 OR e EE 52 Installation Guide DG Precautions nenn anne nenn nennen nennen anne en 54 DIN R MOUNT 54 4 2 1 DIN Rail Installation en ennnnenennnennnnnnnnennnn nme nennen 54 4 2 2 DIN Rail Disassembly ee ccccceeee cece ceeeeeeeeeeeeaeeeseeeseeeseees 55 Wall MOURING usa ern 55 4 3 1 Wall Mounting InstallatioN 55 4 3 2 Wall Mount Disassembly 56 SIM Card lnstallatnon Renee ennnnenennnnnnnn nennen nn nnn nenn nennen 56 Antenna Installation Rennen nennen en nennen en nennen nn nnn nennen 57 Power Supply Installaton Benno nnne nenn nenn nennen 57 Ground Terminal Installation i 57 Connect Cable ee 58 Terminal copnpechon nrn rrnrnr nennen 58 0 EE 60 Description of LED OG Description of LED Lune 64 viii Overview Sections include E introduction E Features 1 1 1 2 Introduction The EKI 1331 combines 3G networks intelligent pro
9. Default Blank Disabled http www 3322 org N A N A N A Disabled N A Disabled Disabled 3 3 5 Static Routes Static routes are created manually and have many different uses After the static route is set packets will be transferred to appointed routes Engineers can create simpler networks by using static routes in place of RIP or OSPF and ensure greater network reliability The proper setting and use of static routing can also improve the performance of a network and guarantee bandwidth for important network applica tions The device supports up to 20 static route entries From the navigation panel select Network gt gt Static Route then enter Static Route page as shown below ADNAHTECH Enabling an Intelligent Planer LET N iworg ENES Friedl EJ SFU Too SA ALPS Static Route l Destination Metrmask Gabe way interface Description 0 0 0 0 255 255 255 0 0 0 0 0 Add Apply Lance Page description is shown below Parameters Description Default Destination Set IP address of the destination 0 0 0 0 Net Mask Set subnet mask of the destination 255 255 255 0 Gateway Set the gateway of the destination N A Interface Users can select which interface accesses the destination N A Description Describe a static route N A 29 EKI 1331 User Manual 3 4 3 4 1 Service In the service section this manual covers nine configurations including DHCP ser vice DNS relay VRRP Device Manager DTU Mo
10. Follow the five steps below to configure the PLC parameters Click Enable in Service gt gt Modbus to SMS Unfold configuration item of PLC List and click the PLC to be used and config 1 2 3 ure one by one 8 PLCs could be added on this page Configure the specific parameters of PLC each PLC can be added to 32 vari ables 1 Set the modbus type Only RTU is available on this model 2 Configure the slave address of each PLC namely the Modbus ID It may be assigned a value from 1 to 247 3 Configure name of the PLC using a maximal length of 16 bytes It is impor tant to name PLCs to avoid confusion in a large scale operation 4 Enter the register address or modbus variable address in the first column Oxxxxx is for discrete inputs 1xxxxx is for a coil 3xxxxx is for the incoming register and 4xxxxx indicates a holding register 5 The second column is the variable type supporting BIT WORD DWORD 6 FLOAT INT16 INT32 and INT64 In the third column are the units of variable with maximum length of 8 bytes This value will appear in SMS and you can leave this field empty The unit of BIT variables should be configured according to HH LL format HH repre sents the corresponding unit of 1 LL represents the corresponding unit of 0 The units of other types of variables will appear directly in SMS Enter the register name in the fourth column This is simply the
11. Relation Rule Value Daad zone A C Ton Recemer Conigli d HONE OR 7 NONE HO Add 3 4 6 1 Enable White list The EKI 1331 is capable of receiving a control and inquiry SMS from any user In order to improve security users can enable the white list function After the white list is set the EKI 1331 only processes SMS from users on the white list meaning any other SMS will be dropped Enable White list d White list Phone saber Haas 35 EKI 1331 User Manual m Up to 10 users may be whitelisted E The first column is a telephone number with a length ranging from 1 to 16 bytes and is mandatory m The second column is the user name with a length ranging from 0 to 16 bytes and is optional After enabling the Modbus to SMS function EKI 1331 can identify two types of SMS commands sent by the users on the white list The EKI 1331 performs an action corresponding to different commands and then sends a response to the SMS user Caution Users can send SMS to EKI 1331 via mobile phone or SMS modem Two types of SMS formats and response message are as follows The SMS to inquire state Users can send the following SMS command to inquire the EKI 1331 operating sta tus and the register values of the PLC Request GET GET pilc1 name plc2 name GET pilc1 name registert register2 plc2 name register3 register4 Request ALARM ALARM 2 3 EKI 1331 User Manual Response Message plc1 connected plc2
12. Settings IP Address Set additional IP Address of LAN Netmask Set netmask of LAN Description Description about this IP address EKI 1331 User Manual 26 00 D0 C9 13 24 F5 192 168 2 1 255 255 255 0 1500 Auto Negotiation N A N A N A 3 3 3 DNS At the core of the internet lies DNS or the domain name system It employs a distrib uted database DDB to map domain names and IP addresses across the web DNS makes it convenient to access the internet so that instead of memorizing IP num bers people can use words to make domain names The device supports the following two functions through the domain name configura tion service m DNS Server the device can function as a local DNS Server m DNS relay as a DNS agent the device can transfer DNS request and response messages between the DNS client and server while and executing domain name analysis in place of the DNS Client To begin setting up the DNS client find the navigation panel select Network gt gt DNS to enter into the DNS window and manually set the DNS information If the DNS information is empty it can be found via dialup Generally users will only need to set the dialup DNS settings if they have static routes on the gateway ADNANTECH Enabling an Intelligent Planet sy SLEM Network Services Firewall Qos VEN Tools Status DNS Primary DNS 00 00 Secondary DNS 0 0 0 0 Apply Cancel Page description is shown below Parameters Description Defau
13. Ur NL ML V m ry i PE 4 7 Ground Terminal installation 1 Screwed down the ground terminal nut 2 Fix the grounding ring of the ground wire to the grounding stud 3 Tighten the ground terminal nut Caution In order to improve anti jamming capability of EKI 1331 the EKI 1331 must be grounded when using According to the on site environment A connect the ground wire to the ground stud of the EKI 1331 57 EKI 1331 User Manual 4 8 Connect Cable Connect EKI 1331 to PC directly with a network cable AM I dames AD ANTECH 4 9 Terminal connection The connection method of Serial interface are used industrial terminal connection please connect the cable to the corresponding terminal inrerface before using EKI 1331 provide two serial interface modes RS232 RS485 When installing remove the terminal from the device loosen the locking screw on the terminal and insert the corresponding cable into the terminal and then tignten the screw The terminal interface description as the picture below oS a TXD IF gt mmm CH zen 5495 tighten screw EKI 1331 User Manual 58 Appendix A FQA A 1 FQA 1 EKI 1331 is powered on but can t access Internet through it Please check m Whether the EKI 1331 is inserted with a SIM card m Whether the SIM card is enabled with data service whether the service of the SIM card is suspended because of an overdue charge m Whether the dialup
14. When upgrading locally check if the local PC and EKI 1331 are in the same net work segment m When upgrading remotely please first make sure the EKI 1331 can access Internet 6 After EKI 1331 establishes VPN with the VPN server your PC under EKI 1331 can connect to the server but the center can t connect to your PC under EKI 1331 Please make sure the firewall of your computer is disabled 7 After EKI 1331 establishes VPN with the VPN server Your PC can t connect to the server EKI 1331 User Manual 60 Please make sure Shared Connection on Network gt WAN or Network gt Dialup is enabled in the configuration of EKI 1331 8 EKI 1331 is powered on but the Power LED is not on m Check if the protective tube is burn out m Check the power supply voltage range and if the positive and negative elec trodes are correctly connected 9 EKI 1331 is powered on but the Network LED is not on when connected to PC m When the PC and EKI 1331 are connected with a network cable please check whether a network crossover cable is used m Check if the network cable is in good condition m Please set the network card of the PC to 10 100M and full duplex 10 EKI 1331 is powered on when connected with PC the Network LED is normal but can t have a ping detection to the EKI 1331 E Check if the IP Address of the PC and EKI 1331 are in the same subnet and the gateway address is EKI 1331 LAN address 11 EKI 1331 is powered
15. analyze the device To configure SMS find the navigation panel select Services gt gt SMS then enter SMS page as shown below ADNANTECH Enabling an Intelliserr Planer System Network Services Firewall 005 VPN Tools Status SMS Enable i Status Query show status English Only eet reboot English Only SMS Access Control Default Policy Accept Phone Number Action Description 056972815077 Accept T Apply Cancel The page description is shown below Parameters Description Default Enable Click to enable SMS Disable This is user defined After configuration the user sends the pre determined message to EKI 1331 which will send status infor Status Query mation to user s mobile phone N A The information include Host SN Uptime the uptime of router for this time of reboot State Online Offline LAN Up LAN IP This is user defined as well After configuration the user will send Reboot N A a user defined message to the EKI 1331 which will then restart 39 EKI 1331 User Manual This accepts by default If the mobile phone number is empty the EKI 1331 will execute the SMS command from any mobile phone Default Policy number If a phone number is entered into the field the EKI 1331 Accept will execute SMS commands from the configured mobile phone number 3 5 Firewall 3 5 1 Basic A firewall is necessary for blocking out malicious packets from the internet On today s internet s
16. logout click System gt gt Logout and then click lt OK gt ADNANTECH gt Enabling an Intelligent Planer System Metwork Services Firewall dos VPN Toots Status sjr Setup 7 peer System Status FYN Time Serial Port EKT 192 168 2 1 KEN EKI 13 Aamin ACCESS 3P60 Conferm Logout System Log www LIDI Config 20 gir a Management HG dv 1134 Upgrade 2029 09 13 18 40 02 boo 04 e Reboo 2015 02 16 17 14 47 Sync Time 0 day 00 00 45 GPU Load 105115 mins 0 05 0 03 0 07 Memory consumption AE RE Aa ATKIN HET THS TotabF ree 26 FENG 14 ETMB ER dd mei Network This section covers network settings include Dialup Cellular LAN DNS DDNS and Static Routes Dialup Cellular Connection With following configuration EKI 1331 can access the internet through the wireless cellular network From the navigation panel select Network gt gt Dialup then enter the Dialup tab as shown below Enabling an Intelligent Planet System Metwork Services Firewall dos VPN Tool Status Hetwork EN Enable d Time scneduie ALL Schedule Manageren SHARED K Metwork Provider IS Custom sg Manage APN CHT Access Number oa te Usemame gprs Password Network Select Type Auto Band ALL r Static IP Connection Mode Abvays Ondine r Redial interval 30 Seconds Show Advanced Options Apply Cancel 23 EKI 1331 User Manual _AD ANTECH Enabling an Intelligert Planer System Heban Show Advanced Op
17. name of the variable with a maximum length of eight bytes Users can define names for EKI 1331 User Manual 34 each variable and this field must be filled The variable address will be replaced by variable name in SMS Caution PLC ID in EKI 1331 can not be repeated neither can PLC names Variable names can be repeated in one PLC variable list AN Each PLC should be defined with ID name and at least one variable 8 Repeat step 3 and add more PLCs 9 Click lt Apply gt button store and apply the new configuration 3 4 6 SMS Alarm Rules EKI 1331 supports the configuration of up to one hundred alarm rules that when trig gered send an alarm message to user s mobile phone User can set the alarm rules and adjust the SMS receiver in the alarm menu The EKI 1331 will collect different variables depending on the alarm rules set by the user When a variable matches the criteria EKI 1331 will send an SMS alarm to all users on the alarm user list along with a message From the navigation panel select Services gt gt SMS Alarm Rules then enter the SMS Alarm Rules window as shown below After setting SMS click the lt Apply gt to save and apply the configuration Enabling ar Intelligent Planet sten Network SEVIDes Firewall os PR Toes Status SMS alarm rules White list Phone number Hame Add Alarm user fist Phone number Name j Add Alarm rule list x Register d 4 n ID PLC name PA Hule Vahi
18. or internet Disable forbid management on a WAN connection Set the range of IP address that is allowed access over aWAN connec Remote Access Allowed Access from WAN Optional tion For example 192 168 2 1 30 or i 192 168 2 1 192 168 2 10 HTTP HTTPS TELNET Description Describe the parameters of manage ment non influence to EKI 1331 EKI 1331 User Manual 18 Default adm N A N A N A Enabled 80 443 23 N A Enabled Enabled N A N A Parameters Description Default Non priviledged Users Console login Username Technician defines a new username N A Password User define the password N A Other Parameters Log Timeout Log Timeout Log Timeout Caution In Username Password section users can modify username and password However these accounts will be non privileged mean b ing the new users cannot create new username non privileged account may only do web logins For security It Is highly recom mended that you modify the default password after your first login Store the password information in a secure location In Non privileged Users section we can create multiple user names Technicians can utilize multiple usernames while logging on a EKI 1331 via serial port or Telnet 3 2 5 System Log A remote log server can be set through System Log Settings and all system logs will be uploaded to the remote log server through the gateway This makes remote log softwar
19. process as shown below Internet Protocol Version 4 TCP IPv4 Properties Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address Obtain DNS server address automatically Use the following DNS server addresses EKI 1331 User Manual 8 2 1 2 Seta Static IP Address Please set the supervisory PC s IP address in the same subnet as the gateway FE or fast Ethernet port In this example the default IP address of gateway FE port is 192 168 2 1 and the subnet mask is 255 255 255 0 Enter the Internet Protocol Version 4 TCP IPv4 Properties window Then select Use the following IP address type the IP address arbitrary value between 192 168 2 2 192 168 2 254 subnet mask 255 255 255 0 and default gateway 192 168 2 1 into the text boxes Finally click lt OK gt to finish setting a static IP as shown below Internet Protocol Version 4 TCP TPvd Properties General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 192 Subnet mask 255 355 2 Default gateway 192 Obtain DNS server a
20. the system time of the host as covered in the set up chapter ADNANTECH Enabling an Intelligent Planer System Network Name Model Serial Number Description Current Version Current Bootloader Version Gateway Time PC Time Up time CPU Load 115115 mins Memory consumption Total Free Services Firewall Qos VPN Tools Status Status EKI 1331 EKI 1331 GP6011412250073 WWW advantech com tw 1 2 0 r3558 1 1 3 r2777 029 09 13 19 00 33 2015 02 16 17 35 18 0 day 00 21 16 0 15 70 03 10 01 2 Sync Time 28 85MB 19 30MB 66 84 49 EKI 1331 User Manual 3 8 2 Modem From navigation panel select Status gt gt Modem then enter Modem page as shown below This page shows Modem status including Signal Level Register sta tus etc ADNANTECH Enabling an Intelligent Planet System Network Services Firewall QoS VPN Tools Status Modem Dialup Modem Type PHSS Status SIM UIM card failure Manufacturer Siemens Product PHSS Signal Level 00 Register Status no registered IMENESN Code 359998041685829 IMSI Code Network Type PLMN LAG Cell ID 3 8 3 Network Connections From navigation panel select Status gt gt Network Connections then enter Net work Connections page as shown below This page shows the connection status of Dialup and LAN ADNANTECH Enabling an Intelligent Planet System Network Services Firewall QoS VPN Tools Status Network Connecti
21. the SMS statis tics Inquire about the startup sta WHITELIST WHITELIST ONJOFF tus of the white list The SMS to perform actions User can send the following SMS command to do the configuration via SMS Request Response Message Description For a PLC named plc1_name set the register value to xxx The plcX name and registerX are both parameters User can set the corresponding variables by configuring these parameters in the command line Such com mande can set multiple variables synchronously Different PLCs are separated by comma Delete all the historical alarm records SET plc1_ name register1 xxx register2 xxx plc2_name register3 xxx register4 xxx Succeed Set register1 to xxx set register2 to xxx set register3 to xxx set register4 to xxx ALARM CLEAN ALL Delete 1 55 alarm SUCCESS Delete the historical records within the a range WHITELIST ONJOFF WHITELIST ONJOFF Start or stop using a white list ADD 13812345678 ADD 13812345678 OK Add users to the alarm list DELETE 13812345678 DELETE 13812345678 OK Delete users on an alarm list ALARM CLEAN xx xx Delete xx xx alarm SUCCESS Alarm User List Alara user list Phoma nenber Nasa Up to ten alarm recipients can be added to the alarm user list E Mobile phone numbers are filled in the first column and may range from 1 to 16 bytes long This column must be filled otherwise users cannot be added m User names are filled in the second column an
22. variable and send it to data center regularly through 3G 2G network Users can check PLC s operation and alarm messages anywhere via internet E Industrial Design In the aspects of EMC anti static grade anti surge level and wide tempera ture range EKI 1331 meet the requirements of industrial and operate easily under harsh environments Metal enclosure IP30 All EMC grade reach level 3 Ethernet port supports 1 5kv isolation transformer protection Serial port support 15kv ESD protection Wide temperature range 20 70 Wide voltage range DC 12 24V E Complete Security Data Transmission Security EKI 1331 uses encrypted channel to communicate with remote controller enabling the process of updating PLC program enjoys high level of encryp tion which is comparable to that of the financial industry Network Protection Security With powerful firewall features EKI 1331 supports SPI State Inspection Secure Shell SSH Intrusion Protection DDoS Defense Attack Defense IP MAC binding etc protecting the equipment against external network attack EKI 1331 User Manual 2 Equipment Management Security Multi level authorization security mechanism realizes centralized authentica tion and authorization management of equipment 1 3 Physical Characteristics E Housing Steel providing IP30 protection Dimensions mm Figure 1 1 DIN Rail Mount Figure 1 2 Wall Mou
23. Seat DIN Rail 4 3 Wall Mounting 4 3 1 Wall Mounting Installation 1 Select the right installation location and make sure have enough space 2 Use a screwdriver to install the wall mounting plate in the rear of the EKI 1331 As shown in picture below 55 EKI 1331 User Manual 3 Take out the screws packed with wall mounting plate use a screwdriver to fix the screws to the mounting position and drop down the EKI 1331 to make the EKI 1331 keep in a stable location as shown in figure below 4 3 2 Wall Mount Disassembly Remove the all screws using a screwdriver Then the EKI 1331 can be removed from the installation location 4 4 SIM Card Installation EKI 1331 support dual card Press the SIM card eject button and will pop up the cor responding card slot Insert a SIM card to the slot as shown in figure below EKI 1331 User Manual 56 4 5 Antenna Installation Gently rotate the movable part of the metal SMA interface until it cannot be rotated the external thread of antenna cable cannot be seen at this point Do not wring the antenna hardly by holding the black rubber Please make sure the antenna was installed well before power on or it may cause device damage 4 6 Power Supply Installation 1 Remove the power terminal from the InGaeway 2 Loosen the locking screw of the power terminal 3 Plug the power cable into the power terminal and lock the locking screw tighten screw ala V emm
24. ade page then follow the steps below 1 Click lt Browse gt choose the upgrade file and then click lt Open gt as shown below Choose file Look in My Documents sl ode G my Music My Pictures Mu Documents Mu Computes a Mu Network Fie name Files of type ai Files r 21 EKI 1331 User Manual 2 Click lt Update gt and then click lt OK gt to begin updating Make sure your screen matches the picture below Ersten Network Services Firewall Dok Tools Status Upgrade i H a a D 0 29 Upgrading Fireware It will take about 1 5 minutes depending on network Please weit and don t interrupt 3 Upgrade firmware succeed and click lt Reboot gt to restart the EKI 1331 3 2 8 Reboot If users need to reboot system please click the System tab then lt Reboot gt and click lt OK gt to restart the system ADNANTECH Enabling ar Intelligent Planet Sym Network Services Firewall 095 VEN Tools Siatus Basic Setup mai K Time 192 168 2 1 M RE e EKI 1331 Serial Fort a EKI 1331 Confem Reboot Admin ACCESS GP601141 System Log vr Ava ME HA ET 12 0r3558 VEAU dE Upgrade 2029 09 13 18 40 02 2015 02 16 17 14 47 Syne Time Ego D day 00 00 45 CPU Load 1 5 15 mins 0 09 0 05 0 01 we 28 818 19 57M8 67 77 Reboot _ Please wait for 39 Seconds ran EKI 1331 User Manual 22 3 2 9 Logout 3 3 3 3 1 If users want to
25. ailed 3 Enable debug mode Disable Provide extra PPP parameters normally user don t need to set these Options include nomppe N A nomppc nodeflate nobsdcomp novj novjccomp NOCCD Set the ICMP Detection Server Blank represents Blank none Set the ICMP Detection Interval 30 seconds Set ICMP Detection Timeout IR6X1 will reboot if 20 seconds ICMP time out Set the max number of retries if ICMP failed 5 Caution Configure the device s schedule to set any downtime A To set the devices schedule go into the Dialup window enter the Schedule Man agement page 25 EKI 1331 User Manual 3 3 2 LAN To create a static LAN connection go into the navigation panel select Network gt gt LAN then enter the LAN page as shown below ADNANTECH Enabling an Srirelligerr Planer System Mebhvork Services Firea VPN I 5 yd LAN ha wi MAC Address 00 DOCS 1224 F5 Default IP Address 193 16821 Metmask 255 255 2550 MITU Default LAN Mode Auto Hegolalon F Multi IP Settings IP Address Hetmask Description Add Apply Cancel The settings are explained below Parameters Description Default MAC The host MAC address in LAN which Address is provided by the manufacturers IP Address Set the IP Address in LAN Set the subnet mask of a local net Net mask Work Set MTU length options to either MTU Default or Manual 1500 is the normal frame size for Ethernet v2 LAN Mode 100M Full duplex 100M Half duplex Multi IP
26. ateway Run the Web browser enter http 192 168 2 1 in the address bar and press Enter to skip to the Web login page as shown below Enter the User Name default adm and Password default 123456 EKI 1331 Login Username gt Password Click button lt Login gt or directly press Enter to enter the Web configuration page as shown below Caution For security it is highly recommended that you modify the default pass word after your first login Store the password information in a secure A location AD ANTECH Enabling an Intelligent Planer system Network Services Firewall dos VEN Tools Status System Status Mame EKI 1331 Model EKI 1331 Senal Number GP6011412250073 Description Www advantech com tw Current Version 17 0 3558 Current Bootioader Version Lis revi Gateway Time 2029 09 13 18 27 35 PC Time 2015 02 16 17 02 20 Syne Time Up time O day 00 03 45 CPU Load 1 5 75 mins 0 51 0 29 0 11 Memory consumption eee Aaa TER AA TotalFree Pdl Kelt RAM 15 JAMB 67 Fila Click lt Sync Time gt to synchronize the gateway s clock with the system time of the host EKI 1331 User Manual 14 3 2 3 2 1 System The system configuration process involves nine steps Basic Setup Time Serial Port Admin Access System Log Configuration Management Update Reboot Logout Basic Setup From the navigation panel select System gt gt Basic Setup then enter the Basic Setup pa
27. connect from the Proxy Server If the supervisory PC uses a proxy server to access the Internet it is necessary to disconnect from the proxy and remove any proxy settings The operating steps are as follows E Open Internet Explorer Select Tools gt gt Internet Options to enter the window Internet Options Lu duba C O Mu d db Browsing history Delete temporary files history cookies saved passwords K3 and web form information Delete browsing history on exit Change search defaults er how webpages are displayed in SCH Appearance 11 EKI 1331 User Manual m Select the tab Connect and click the button lt LAN Setting L gt to enter the win dow LAN Setting If the option Use a Proxy Server for LAN is checked uncheck it Click the lt OK gt button and continue to the web configuration section of the manual Automatic configuration Automatic configuration may override manual settings To ensure the use of manual settings disable automatic configuration Use automatic configuration script Proxy server Use a proxy server for your LAN These settings will not apply to dial up or VPN connections 80 EKI 1331 User Manual 12 Configuration Sections include E Logging in the Browser Inter face E System m Network E Service m Firewall E QoS E Tools m Status 3 1 Login the Web Configuration Page of G
28. d may range from 0 to 16 bytes long This column may be left empty m Telephone numbers should be non duplicated Alarm Rule List Alaram rule list PLC nana aged tar elei Falsaj Relation Bulet Waleed Bed ACTION Keoeiver Content page Bibbia w SONE e DR e SE e VM w In this section of interface the technician will create an alarm rule list Each line defines an alarm rule and a maximum of one hundred alarm rules can be configured The technician will match mathematical expressions and compare values to a vari able in each rule To set an alarm rule follow these steps 37 EKI 1331 User Manual E Selecta PLC in the first column Any PLC previously setup in the Modbus to SMS chapter of this manual will appear in a drop down menu m Select a variable name in the second column and the corresponding variable of the PLC will appear above it The technician will compare values to this variable E Compare the variable to a value by selecting an operator in the third column The available options are NONE gt gt lt lt and m Define the first value in the fourth column This value will be compared to the main variable For example temperature gt 200 means that when the tempera ture is greater than or equal to 200 an alarm will be sent m Define the relationship between the first expression and the second expression in the fifth column by selecting OR AND or XOR E Select a second operator in the sixth c
29. d on other network computers or change shanng settings a Troubleshoot problems HomeGroup D RESO V Diagnose and repair network problems or get treubleshooteng informabon Internet Options Lenovo Internet Lonnechon Windows Firewall EKI 1331 User Manual 6 2 Click the button local Connection gt to enter the window Local Connection Status Connection IPv4 Connectivity Internet IPv amp Connectivity No Internet access Media State Enabled Duration 00 40 48 Speed 100 0 Mbps Details Sent A Received Bytes 9 323 919 208 550 231 Click lt Properties gt to enter the window Local Connection Properties as shown below ection uses the following items E Client for Microsoft Networks Ja Trend Micro NDIS 6 0 Filter Driver l n te Via Driver 05 Packet Scheduler Al File and Printer Sharing for Microsoft Networks si Intemet Protocol Version 6 TCP IPv6 SH Intemet Protocol Version 4 TCP Pv4 Uninstall Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks 7 EKI 1331 User Manual 4 Select Internet Protocol Version 4 TCP IPv4 Click lt Properties gt to enter Internet Protocol Version 4 TCP IPv4 Properties Select Obtain an IP address automatically and Obtain DNS Server address automatically then click lt OK gt to complete the
30. dbus to SMS SMS alarm rules and Mbsms variable template DHCP Service DHCP Dynamic Host Configuration Protocol is a network protocol for LAN utilizing UDP and TCP DHCP automatically distributes IP addresses for either a local net work or network service provider and can aid network administrators in managing all the computers on a network A DHCP server refers to a computer managing DHCP standard in a network It distributes IP addresses once the work station logs on and ensures that no duplicate IP addresses are assigned DHCP Server dramatically sim plifies network management tasks and is a necessity in today s network To enable the DHCP server find the navigation panel select Services gt gt DHCP Service then enter DHCP Service page as shown below The DHCP server sup ports up to 20 addresses ADNANTECH Enabling an Intelligent Planet System Network Services Firewall Qos VPN Tools Status DHCP Service Enable DHCP d IP Pool Starting Address 19216822 IP Pool Ending Address 192 166 2 100 Lease 60 Minutes DNS Edit Windows Name Server WINS 0000 Static DHCP MAC Address IP Address Host 00 00 00 00 00 00 197 1682 2 Apply Cancel The page is described below Parameters Description Default Enable DHCP Check to enable DHCP Enable IP Pool Starting Address Set the starting IP address of DHCP pool 192 168 2 2 IP Pool Ending Address Set the ending IP address of DHCP pool 192 168 2 100 Set the valid time
31. ddress automatically Use the following DNS server addresses Preferred DNS server 8 8 98 Alternate DNS server E Validate settings upon exit 9 EKI 1331 User Manual 2 2 1 Click the button lt Start gt at the lower left corner Type cmd into the field and run cmd exe EN C Windows system32 cmd exe Microsoft Windows Version 6 1 7600 Copyright c gt 2869 Microsoft Corporation All rights reserved C lsersvdlz gt 2 Enter ping 192 168 2 1 and click the lt OK gt button 192 168 2 1 is the default IP address of the EKI 1331 If the connection is good you will see four returned packets If there is no response be sure to check your connection and your supervisory PC s network settings ga C Windows system3A cmd exe Microsoft Windows Version 6 1 7688 Copyright tc 2009 Microsoft Corporation All rights reserved Whsers dlzoping 192 168 2 1 inging 192 168 2 1 with 32 bytes of data Reply from 192 168 2 1 bytes 32 timetims TTL 64 Reply from 192 168 2 1 bytes 32 timetims TTL b4 Reply from 192 168 2 1 bytes 32 time lt ims TTL 64 Reply from 192 168 2 1 hytes 32 time lt ims IIL b4 Ping statistics for 192 168 2 1 Packets Sent 4 Received 4 Lost iHz loss Approximate round trip times in milli seconds Minimum ms Maximum Bns Average ns F gt Users dlz gt EKI 1331 User Manual 10 2 3 Dis
32. disconnected plc1 OUTPUT1 on OUTPUT2 off plc2 OUTPUT3 on OUTPUT4 on PIc1 register1 5 register2 6 plc2 register3 1 8 register4 2 2 Response Message Alarm total 55 53 date time context1 54 date time context2 55 date time context3 Alarm total 55 2 date time context1 3 date time context2 4 date time context3 36 Description Inquire about the name and status of all PLCs connected to the EKI 1331 Inquire about the PLC vari ables with names of plc1_name plc2_name The plcX names are parameter Users can query different PLC variables by modifying the plcX name Different PLCs are separated by a comma This command finds the value of a variables under a PLC named plcX_name The plcX_name and registerX are parameters Users can find the name of corresponding variables by trying different perameter commands By entering multiple registers multiple variables can be found at the same time Differ ent PLCs are separated by comma Description Find a count of historical alarm records and return the latest three historical alarms Inquire about historical records within the appointed number range It can request maximum of five historical records each time 3 4 6 2 3 4 6 3 Signal strength dBm xx Network status Registered to home network Received message 10 Sent mes MSGSTATUS sage 15 Failed sent message 0 Unauthorized message NETSATUS Learn the network status Inquire about
33. e such as Kiwi Syslog Daemon is a necessity on the host Kiwi Syslog Daemon is free log server software for Windows which can receive record and display logs from host such as gateway exchange board and Unix host After downloading and installing Kiwi Syslog Daemon it mus be configured through the menus File gt gt Setup gt gt Input gt gt UDP From the navigation panel select Sys tem gt gt System Log then enter System Log page as shown below AD ANTECH Enabling an Intelligent Planet System Network Services Firewall VPN Tools Status System Log Log to Remote System LOG O Console Apply Cancel Page description is shown below Parameters Description Default Log to Remote System Enable remote log server Disable IP address Port UDP Set the IP and Port of remote log server N A Port 514 Log to Console Print the log to console Disable 19 EKI 1331 User Manual 3 2 6 Config Management Users may import an old configuration or backup the current configuration From the navigation panel select System gt gt Config Management then enter the Config Management page as shown below AD ANTECH EN Enabling an Intelligent Planet System Network SETVICES Firewall Qos VEN 10015 salus Contig Management Gateway Configuration REG config dal Import Backup Restore default configuration Network Provider ISP BUER networks dr Import Backup Page description is shown below
34. ecurity is more important than ever which is why the EKI 1331 is well equipped to protecting the local network and provide a security barrier from external threats To configure the firewall go to the navigation panel select Firewall gt gt Basic then enter the Basic config page as shown below ADNANTECH Erabling an Intelligent Planet System Network Services Firewall dos VPN Tools Status Basic Default Filter Policy Accept T Block Anonymous VIAN Requests ping Filter Multicast Defend DoS Attack Apply Cancel The page description is shown below Parameters Description Default Default Filter Policy Choose to either Accept or Block filtering Accept Block Anonymous WAN Request ping Check to deny anonymous ICMP ping requests Disable Filter Multicast Check to filter multicast packets Enable Defend DoS Attack Select to enable DoS attack prevention Enable EKI 1331 User Manual 40 3 5 2 Filtering Access control has the following functions E Prevent unwanted users from accessing network resources m Permitting staff to access network resources m Preventing staff from accessing the wrong network resources To enable Access Control From the navigation panel select Firewall gt gt Filtering then enter Filtering page as shown below ADNANTECH Enabling an Intelligent Planer System Network Services Firewall dos VPN Tools Status Filtering Enable Proto Source Source Port De
35. ge as shown below ADNANTECH Enabling an Intelligent Planet System Network Services Firewall O05 VPN Tools Status Basic Setup Language English r Hostname EKI 1331 Apply Cancel Page description is shown below Parameters Description Default Language Select the language of configuration page English Hostname Set the name of EKI 1331 Gateway 15 EKI 1331 User Manual 3 2 2 Time In order to ensure the coordination of the gateway and other devices users need to set the system time and time zone correctly From the navigation panel select Sys tem gt gt Time then enter the Time webpage as shown below Click lt Sync Time gt to synchronize the time of the gateway with the system time of the host ADNANTECH Enabling an Intelligent Planer Sysiem Network Gateway Time PL Time Timezone Custom TZ String Auto Update Time Apply Cancel Services Firewall dos 2029 09 13 15 20 03 2015 02 16 17 03 38 Syne Time Custom CST 4 Disabled 7 The terms are explained below Parameters Gateway Time PC Time Timezone Custom TZ String Auto update Time EKI 1331 User Manual Description Display the system time of Gateway The current time of supervisory PC Set time zone Set the time zone of the Gateway Time Update Interval 16 VPN Tools Status Time Default 2000 01 01 08 16 47 N A Custom CST 8 Disabled 3 2 3 3 2 4 Serial Port On the serial port settings config pa
36. ge users need set the serial configuration of the gateway with the same parameters as the connected device If users are using soft ware similar to PuTTY users should set their serial configs the same as the settings below From the navigation panel select System gt gt Serial Port then enter Serial Port page as shown below ADNANTECH FE nabling an Intellizerf Planer Sysiem Network Services Firewall dos VPN Tools Status Serial Port Baudrate 115200 Data Blis B Parity None Stop Bit 1 e Software Flow Control Mode RS232 7 Apply Cancel Page description is shown below Parameters Description Default Baud Rate Serial baud rate 115200 Data Bit Serial data bits 8 Parity Set parity bit of serial data None Stop Bit Set stop bit of serial data 1 Software Flow Control Enable Software Flow Control Disable Mode Select serial type RS232 Admin Access HTTP HTTP Hypertext Transfer Protocol is used for transferring web pages on Internet After enabling HTTP service on device users can log on via HTTP and access the device using a web browser HTTPS HTTPS Secure Hypertext Transfer Protocol supports SSL Security Socket Layer and encrypts data transfers This prevents man in the middle attacks when data passes either through the local network or across the internet TELNET Telnet protocol provides telnet and virtual terminal functions through a network The device supports both a client mode and a server mode In c
37. he equipment has been dropped and damaged The equipment has obvious signs of breakage DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW 20 C 4 F OR ABOVE 60 C 140 F THIS COULD DAMAGE THE EQUIPMENT THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER S INSTRUCTIONS The sound pressure level at the operator s position according to IEC 704 1 1982 is no more than 70 dB A DISCLAIMER This set of instructions is given according to IEC 704 1 Advantech disclaims all responsibility for the accuracy of any statements contained herein EKI 1331 User Manual IV Safety Precaution Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage u To avoid electrical shock always disconnect the power from your PC chassis before you work on it Don t touch any components on the CPU card or other cards while the PC is on m Disconnect power before making any configuration changes The sudden rush of power as you connect a jumper or install a card may damage sensitive elec tronic components V EKI 1331 User Manual EKI 1331 User Manual VI Contents Chapter Chapter Chapter 1 EE GE E QN 2 2 1 2 2 2 3 3
38. kbit s Set the bandwidth limit or rate 100kbit s Priority Set the priority Medium Description Describe the configuration N A EKI 1331 User Manual 46 3 7 3 7 1 Tools The EKI 1331 comes with several tools to help admins diagnose network problems including E Ping m Trace route m Link Speed Test Ping Ping a tool many technicians are familiar with It simply sende ICMP packets across the network to a remote host and then retransmits an ICMP packet back to the origi nal sender To do a ping enter the navigation panel select Tools gt gt Ping then enter the Ping page as shown below ADNANTECH Enabling an Intelligent Planet System Network Services Firewall gos VPN Tools Status PING Hos Ping Ping Couni Packet Size 32 Bytes Expert Options Page description is shown below Parameters Description Default Host Destination IP for the ping N A Ping Count Number of pings sent 4 times Packet Size The size of the ping packet sent 32B is recommended 32 Bytes Expert Options Advanced parameters N A 47 EKI 1331 User Manual 3 7 2 Trace Route The trace route tool sende an ICMP or UDP packet to a remote host Each time the packet is routed onto a different network that router will return a response Trace route allows network engineers to diagnose routing problems To preform a trace route go to the navigation panel select Tools gt gt Traceroute then scroll down to the Traceroute page as sh
39. lease of IP address Lease obtained by DHCP 60 minutes DNS Set DNS Server 192 168 2 1 Windows Name Server WINS Set the WINS binding 0 0 0 0 Static DHCP Set the MAC address of a designated IP MAC Address 00 00 00 00 00 00 address IP address Set the static IP address of the host 192 168 2 2 Host Set the hostname N A EKI 1331 User Manual 30 3 4 2 DNS Relay DNS forwarding DNS forwarding is open by default You can set the specified Domain Name lt gt IP Address to let IP address match with the domain name thus allowing access to the appropriate IP through accessing to the domain name From navigation panel select Network gt gt DNS then enter DNS Relay page as shown below ADNANTECH Enabling an Intellizerr Planer System Network Services Firewall QoS VPN Toots Status DNS Relay Enable DNS Relay Static IP address lt gt Domain Name Pairing IP Address Host Description Add Apply Cancel The page description is shown below Parameters Description Default IP Address Map an IP to a hostname N A Host Set the name of DNS entries N A Description Describe DNS entry N A Caution When enabling DHCP the DHCP relay is also enabled automati cally Relay cannot be disabled without disabling DHCP A m While using dynamic DNS the DNS relay service should be turned on ZS A maximum of twenty IP to domain name pairs may be configured 31 EKI 1331 User Manual ing or routing discove
40. lient mode the telnet cli ent sends request to the telnet server creating a session While in server mode the device supports Telnet connections for incoming clients allowing for remote access 17 EKI 1331 User Manual Console The console port also called the access or serial port refers for initial configuration and subsequent management of a device It has the same terminal as the telnet cli ent From the navigation panel select System gt gt Admin Access then enter Admin Access page as shown below ADNANTECH Enabling an Intelligent Planet Fy slem Menwork Services Firewall dos WE Tools Admin Access Username Password Username adm Old Password Mew Password Sana New Password Management Enable Service Type Service Port zen a eig on NOM WAN Description g HTTP 30 o HTTPS TELNET 23 sg sg Console Non privileged users Username Password Page description is shown below Parameters Description Username Username for configuration web login To change the password users must Old Password input the old one New Password Input new password Confirm New Password Input the new password again Management HTTP HTTPS TELNET Console Enable Select to enable HTTP Service Port Select management port Enable allow management of the EKI 1331 over the local network or Local Access LAN Disable forbid management of the EKI 1331 over LAN Enable allow management of the EKI 1331 over the WAN
41. link Off Off Off Blink Blink On Blink 64 Modem works abnormally No signal detected Signal lt 9 Signals19 Definition Power on Initialization succeed Dialing Dialing succeed Upgrading Reset Succeed 65 EKI 1331 User Manual AD ANTECH Enabling an Intelligent Planet www advantech com cn Please verify specifications before quoting This guide is intended for reference purposes only All product specifications are subject to change without notice No part of this publication may be reproduced in any form or by any means electronic photocopying recording or otherwise without prior written permis sion of the publisher All brand and product names are trademarks or registered trademarks of their respective companies O Advantech Co Ltd 2015
42. lt Primary DNS Set Primary DNS N A Secondary DNS Set Secondary DNS N A 27 EKI 1331 User Manual 3 3 4 DDNS DDNS Dynamic Domain Name Server automatically adds DNS entries to a server in real time DDNS automatically logs IP addresses and host names to its database when hosts connect to the network When hostnames have been recorded they may be used in the place of IP addresses DDNS will be particularly useful in an IPV6 envi ronment To set up DDNS go into the navigation panel select Network gt gt DDNS then enter DDNS page as shown below ADNANTECH Enabling an Intelligert Planet System Network Services Firewall dos VEN DONS Dynamic DNS gt Dialup Current Address Service Type DynDNs Static T URL Lsername Password Hosiname Wildcard L Backup MA Force Update Last Update Last Response Apply http mw dyndns com Cancel Page description is shown below Parameters Current Address Service Type URL Username Password Hostname Wildcard MX Backup Mx Force Update EKI 1331 User Manual Description Show the current IP address Select DDNS Provider Automatically generate users do not need to set Registered username for DDNS Registered password for DDNS Registered hostname for DDNS Set whether the server supports wildcards Whether to update the mailbox record Whether to update the mailbox record Force update records after modifying the settings 28 Tools Status
43. ndwidth limits Bandwidth Control Bandwidth control set a limit on the upload and dowload speeds when accessing external networks To configure bandwidth control go into the navigation panel select QoS gt gt Band width Control then enter Bandwidth Control page as shown below ADNANTECH Enabling an Intelligent Planet System Network Services Firewall 008 VPN Bandwidth Control Enable Outbound Limit Max BW 100000 kbit s Inbound Limit Max BW 100000 kbit s Apply Cancel The page description is shown below Parameters Description Default Enable Check to enable Disable Outbound LimitMax Get the maximum upload rate 100000kbit s Bandwidth Inbound Limit Max Get the download bandwidth limit 100000kbit s Bandwidth 45 EKI 1331 User Manual 3 6 2 IP Bandwidth Limit Technicians may limit the bandwidth on individual hosts and devices by setting IP based bandwidth limits To configure the IP bandwidth limit go to the navigation panel select Firewall gt gt IP BW Limit and then enter the IP BW Limit page as shown below ADNANTECH Enabling an Intelligent Planet System Network Services Firewall QoS VPN IP BW Limit Enable IP Address Rate kbit s Priority Description h 11 00 Medium Apply Cancel The page description is shown below Parameters Description Default Enable Check to enable an IP bandwidth limiter Enable IP Address Set the IP address to be limited N A Rate
44. nt 3 EKI 1331 User Manual EKI 1331 User Manual Login Gateway Sections include Establish Network Connection Test the connection between supervisory PC and EKI 1331 m Cancel the Proxy Server 2 1 Establish Network Connection 2 1 1 Automatic Acquisition of IP address Please set the supervisory PC to automatic acquisition of IP address and automatic acquisition of DNS server address which is the default configuration of Windows This way the EKI 1331 automatically assign an IP address to the super visory PC using DHCP 1 Open Control Panel double click Network and Internet icon and enter Network and Sharing Centers ee n Control Panel All Control Panel Rem Network an Control Panel Home e i View your basic network information and set up connections Manage wireless networks A T t See full map unge aat SETTI NB000528 ADVANTECH CORP Internet Change advanced shanng This computer settings e 3 View your actrve networks Connect or disconnect ADVANTECH CORP Accesstype Internet Tree Domain network Connections Tsi Change your networking settings vg Set up new connection Gr network Set up wireless broadband dial up ad hoc or VPN connection or set up router or access pomt Connect to a network Connector reconnect to a wireless wired dial up or VPN network connection Choose hemegr vp and shanng epuone Access files and printers locate
45. olumn The options that can be selected are NONE gt gt lt lt and E Define a second value in the seventh column E Inthe eighth column the user must define a dead zone which acts as a buffer After the alarm is trigger it will not be sent until the variable exceeds the dead zone value It is only effective for numerical non bit wise values Set the value to zero to eliminate the dead zone E Inthe ninth column titled ACTION users may select YES to enable user defined alarm message user need define the alarm message on Context in the eleventh column Otherwise the default alarm message will be sent The maximum length for a short message is 140 bytes E The mobile phone number of a recipient is input in the tenth column E A user defined alarm message may be set in the eleventh column When trig gered this message will be sent in the form of an SMS The alarm SMS are divided into two types m If the selection for ACTION in the ninth column is NO the system will send the automatically generated defaulted alarm short message The message will be defined by the variable for example Alarm plc2 OUPUT on or Alarm plc AB VOLT 238V m If the selection of ACTION is YES the system will send a user defined alarm Below is an example of an alarm rule Alarm rule l st PLC name ee Fiori Valu Fron Rulez Valuuz Dead tone ACTH Recetrer Comical PLUS a1 PLEJ iR WOLT
46. on but can t configure through the web interface E Whether the IP Address of your computer is the same subnet with EKI 1331 and the gateway address is EKI 1331 LAN address m Check the firewall settings of the PC used to configure EKI 1331 whether this function is shielded by the firewall 12 The EKI 1331 dialup always fails can t find out why Please restore EKI 1331 to factory default settings and configure the parameters again 13 How to restore EKI 1331 to factory default settings m Press and hold the Restore button power on EKI 1331 E Release the button until after the STATUS LED flashes and the ERROR LED is on m After the button is released the ERROR LED will go off within 30s press and hold the Restore button again until the ERROR LED flashes m Release the button the system is now successfully restored to factory default settings 61 EKI 1331 User Manual EKI 1331 User Manual 62 Appendix B Description of LED B 1 Description of LED Name Power Status Warn Error Modem Signal weak Signal medium Signal strong Color Red Green Yellow Red Green Green Green Green Description On Power on Off Power off See the information below On Modem works normally Off On 92Signal gt 1 Off On 192Signal210 Off On 312Signal220 Off Some of the indicators are defined below STATUS On Blink Blink Blink Blink Blink EKI 1331 User Manual WARN ERROR On Off On Off B
47. ons Dialup Connection Type Dialup IP Address 0 0 0 0 Netmask 0 0 0 0 Gateway 0 0 0 0 ONS 0 0 0 0 MTU 1500 Status Disconnected Connection time Connect Disconnect LAN MAG Address 00 18 05 08 ED 0E IP Address 192 168 2 1 Netmask 299 209 ZOU MTU 1500 DNS EKI 1331 User Manual 50 3 8 4 Route Table From navigation panel select Status gt gt Route Table then enter Route Table page as shown below This page shows the route table of EKI 1331 ADNANTECH Enabling an Intelligent Planet System Network Services Firewall Dos VPN Tools Status Route Table Destination Netmask Gateway Metric Interface 19216820 255 255 255 0 0 0 0 0 land 127006 255 0 0 0 0 0 0 0 D lo 3 8 5 Device List From navigation panel select Status gt gt Device List then enter Device List page as shown below This page shows the device link of EKI 1331 ADNANTECH Enabling an Intelligent Planet System Network Services Firewall QoS VPN Tools Status Device List interface MAC Address IP Address Host land FO DE F1 54 13 8F 192 168 2 39 3 8 6 Modbus PLC From navigation panel select Status gt gt Modbus PLG then enter Modbus PLC page as shown below This page shows the parameters of Modbus PLC linked with System Hetwork Services Firewall CS 10085 Stalus Modbus PLC EN Regsiter name Register addressibase 1 Value Units Name PLC Address Connect state disconnect OUTPUT 19200 d AB VELT 11100 d
48. own below AD NANTECH Enabling an Intelligent Planet System Network Services Firewall 105 VEN Tools Status Traceroute Host Trace Maximum Hops 20 Timeout 3 Seconds Protocol UDP e Expert Options The page description is shown below Parameters Description Default Host The destination for trace route N A Max Hops Set the maximum number of hops 20 Time Out Set the timeout for dropped packets 3 sec Choose between ICMP and UDP protocol ICMP may UDP be blocked on some networks Expert Options Advanced parameters N A Protocol 3 7 3 Link Speed Test The EKI 1331 uses a simple upload and download to test the link speed To start the speed test enter the navigation panel select Tools gt gt Link Speed Test then enter Link Speed Test page as shown below ADNANTECH Enabling ar Intelligent Planet System Network Services Firewall JOS VPN Tools Status Link Speed Test MEER FERN upload download EKI 1331 User Manual 48 3 8 Status The status chapter covers the following System Modem Network Connections Routing Table Device List ModbusPLC Event Logs 3 8 1 System From navigation panel select Status gt gt System then enter the System page as shown below This page displays system statistics including Name Model Current Version Gateway Time PC Time UP Time CPU Load Memory Consumption etc Technicians may click the lt Sync Time gt button to synchronize the gateway with
49. parameters e g APN dialup number username and pass word are correctly configured m Whether the IP Address of your computer is the same subnet with EKI 1331 and the gateway address is EKI 1331 LAN address 2 EKI 1331 is powered on have a ping to detect EKI 1331 from your PC and find packet loss Please check if the network crossover cable is in good condition 3 Forget the setting after revising IP address and can t configure EKI 1331 r Method 1 connect EKI 1331 with serial cable configure it through console port Method 2 within 5 seconds after EKI 1331 is powered on press and hold the Restore button until the ERROR LED flashes then release the button and the ERROR LED should goes off press and hold the button again until the ERROR LED blinks 6 times the EKI 1331 is now restored to factory default settings You may con figure it now 4 After EKI 1331 is powered on it frequently auto restarts Why does this hap pen Please check m Whether the module works normally m Whether the EKI 1331 is inserted with a SIM card m Whether the SIM card is enabled with data service whether the service of the SIM card is suspended because of an overdue charge m Whether the dialup parameters e g APN dialup number username and pass word are correctly configured m Whether the signal is normal m Whether the power supply voltage is normal 5 Why does upgrading the firmware of my EKI 1331 always fail Please check m
50. redial 115 can not open det USB er Jan 08 00 14 redial 1 15 can not open devtiy GB Download Log File Download System Diagnosing Data EKI 1331 User Manual 52 Chapter 4 Installation Guide 4 1 Precautions Power Requirments 12 24 Vpc Please note that the power supply voltage level Environmental Requirement Working 0 70 C 50 70 C permission Storage 40 85 C Humidity 5 90 relative humidity non condensing Avoid direct sunlight away from heat sources or areas with strong electromag netic interference EKI 1331 need to be installed in an industrial DIN Rail Please check whether installed the needed cables and connectors 4 2 DIN Rail Mounting 4 2 1 DIN Rail Installation 1 2 Selected installation position and make sure there is enough space Fix the upper part of DIN rail seat on the DIN rail Rotate the device from the bottom as shown by arrow 2 please see the installation instruction bwlow then the DIN rail seat is installed on DIN rail DIN Rail Sest DIN Rail EKI 1331 User Manual 54 4 2 2 DIN Rail Disassembly 1 As shown the arrow 1 in the picture below Press downward the EKI 1331 to make sure the bottom have the enough space to break away from the DIN rail 2 Rotate EKI 1331 to the direction of arrow 2 and move outward the bottom of EKI 1331 Once the bottom break away from the rail seat EKI 1331 can be removed from the DIN rail DIN Rail
51. ry protocol on each host To enable VRRP go to the navigation panel select Services gt gt VRRP then enter VRRP page as shown below ADNANTECH Enabling an Intelligent Planet 3 4 3 VRRP Virtual Router Redundancy Protocol VRRP is a protocol for allowing automatic failover and redundancy in routers It cre ates a virtual router meaning multiple physical routers can be assigned to one gate way or one host The main gateway controls the IP of the virtual gateway and routes packets to virtual IP addresses If the main gateway drops a dynamic failover pro cess elects a new gateway The IP address of the virtual gateway can be set as the default gateway for hosts because it is the first hop The benefit of using VRRP is serviceability The network administrator can avoid the configuration of dynamic rout System Network Services Firewall dos VPN VRRP Enable YRRP I Li Group ID 1 T Priority 20 254 highest Advertisement Interval 60 Seconds Virtual IP Authentication Type None r Virtual MAC Monitor None Enable VRRP II sg Group ID 2 Priority 10 254 highest Advertisement Interval hy h DU Seconds Virtual IP Authentication Type More 7 virtual MAL Monitor None Apply Cancel The page description is shown below Parameters Description Enable Check to enable VRRP Group ID Select a group id of gateway range 1 255 Priority Select a priority for the gateway range 1 254
52. ssumes no liability under the terms of this warranty as a consequence of such events Because of Advantech s high quality control standards and rigorous testing most of our customers never need to use our repair service If an Advantech product is defec tive it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any onscreen messages you get when the problem occurs 2 Call your dealer and describe the problem Please have your manual product and any helpful information readily available 3 If your product is diagnosed as defective obtain an RMA return merchandize authorization number from your dealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for warranty service 5 Write the RMA number visibly on the outside of the package and ship it prepaid to yo
53. stination een Action Log Deseription gd ALL Sr 2 9 0 0 0 Accept T Apply Cancel Page description is shown below Parameters Description Default Enable Check to enable filtering Enable Protocol The available options are TCP UDP ICMP and all All Source IP address Set the source IP address 0 0 0 0 0 Source Port Set the source port N A Destination IP Set the destination IP address N A Destination Port Set the destination port N A Action Select either accept or block Accept Log log can print the access IP address Disable Description Describe your configuration N A 41 EKI 1331 User Manual 3 5 3 Port Mapping The EKI 1331 support Network Address and Port Translation It allows remote com puters for example computers on the Internet to connect to the local device that linked to LAN interface To configure port mapping go into the navigation panel select Firewall gt gt Port Mapping then enter Port Mapping page as shown below ADNANTECH Enabling an Intelligent Planer System Network Services Firewall dos VPN Tools Status Port Mapping KA Internal a Enable Proto Source Service Port Internal Address Port L Description TCP 0 00 00 2080 2030 Apply Gancel Page description is shown below Parameters Description Default Enable Check to enable port mapping Enable Protocol Select either TCP or UDP TCP Source Set an external source IP 0 0 0 0 0 Service Port Set the external port of service 8080 In
54. ter reference Disconnect this equipment from any AC outlet before cleaning Use a damp cloth Do not use liquid or spray detergents for cleaning For plug in equipment the power outlet socket must be located near the equip ment and must be easily accessible Keep this equipment away from humidity Put this equipment on a reliable surface during installation Dropping it or letting it fall may cause damage The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is correct before connecting the equipment to the power outlet Position the power cord so that people cannot step on it Do not place anything over the power cord All cautions and warnings on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient overvoltage Never pour any liquid into an opening This may cause fire or electrical shock Never open the equipment For safety reasons the equipment should be opened only by qualified service personnel If one of the following situations arises get the equipment checked by service personnel The power cord or plug is damaged Liquid has penetrated into the equipment The equipment has been exposed to moisture The equipment does not work well or you cannot get it to work according to the user s manual T
55. ternal Address Set the internal IP for mapping Blank Internal Port Set the mapping port 8080 Log Click to enable a log about port mapping Disable Description Write a description to avoid future confusion Blank EKI 1331 User Manual 42 3 5 4 Virtual IP Mapping After a PC in LAN has been assigned a virtual IP external hosts can access it via a virtual IP The functions usually work with VPN To enable virtual IP mapping go into the navigation panel select Firewall gt gt Virtual IP Mapping then enter the Virtual IP Mapping page as shown below ADNANTECH Enabling an Intelligent Planer System Network Services Firewall Dos VPN Tools Status Virtual IP Mapping Virtual IP for Gateway Source IP Range Enable Virtual IP Real IP Log Description af Apply Cancel Page description is shown below Parameters Description Default king IP for Gate Set a virtual IP for the EKI 1331 Blank Source IP Range Set range of the external source IP addresses Blank Virtual IP Set an external virtual IP Blank Real IP Set a real IP Blank Log Enable a log of virtual IP events Disable Description Describe this configuration Blank 43 EKI 1331 User Manual 3 9 9 3 5 6 DMZ All Port Mapping DMZ is like a virtual server the all port of router map to the DMZ host From the navigation panel select Firewall gt gt DMZ then enter DMZ page as shown below ADNANTECH Enabling an Intelligent Planet S
56. tions initial Commands Dal Timeout MTU MRU TX Queue Lengih Authentcalion Type Enable IP head compression Lise default asyncmap Use Peer DNS Link Detection interval Link Detection Max Reiries Debug Expert Options ICMP Detection Server KH Detection Internal Ceres Erewa Gas VPN Took Dialup af L t Second 1500 t500 AWwo T z Fi RE Sa Ono disable nomppe nomppco nodeflate nobsdcomp nov ol Comp noccp 10 gecip at Terminology is listed below Parameters Basic Config Enable Time Schedule SHARED ISP APN Access Number Username Password Network Select Type Static IP Connection Mode Redial Interval Advanced Options Initial Commands EKI 1331 User Manual Description Enable PPP dialup Select timetable for online and offline We need defined timetable through Schedule Manage ment in advance Enabled enable NAT or network address translation Local addresses can be translated to global WAN address on a one to many basis Disable disable NAT Select local ISP if not listed here please select Customer APN provided by your Local ISP Dialup phone number provided by your Local ISP Some APNs need a username and password to complete the PPP connection but not every APN needs a username Some APNs need a username and password to do the PPP connection but not every APN needs a password Choose mobile network type The a
57. tocol conversion and VPN technology to create a product designed for remote maintenance and management The EKI 1331 features remote communication between the controller and data center which provides an ingress or gateway for the remote diagnosis and maintenance of the machines The controller technicians can construct large scale networks for remote maintenance of equipment The EKI 1331 can also be employed as a communication gateway for equipment to coordinate with each other With the EKI 1331 technicians in the office can remotely program field PLCs monitor variables and receive alerts in real time The EKI 1331 supports both communication via the PLCs Ethernet port and via the serial port EKI 1331 also supports status queries PLC controls and alarm message via SMS The EKI 1331 series utilizes the ubiquitous cellular network to the fullest and opens new horizons in remote management and machine to machine communication Features E Designed for the Communication of Industrial Equipment SMS Function SMS Alarm users can receive timely alarm message when PLC exception occur in field SMS Check and Control users can remotely monitor and control PLC PLC Collaboration PLCs can communicate with each other via SMS ensur ing more PLCs work collaboratively E Remote Maintenance Users can achieve PLC s remote programming via secure channel serial Ether net pot E Remote Monitoring EKI 1331 can check real time operating status
58. ur dealer Part No Edition 1 Printed in Taiwan October 2015 EKI 1331 User Manual il Declaration of Conformity CE This product has passed the CE test for environmental specifications Test conditions for passing included the equipment being operated within an industrial enclosure In order to protect the product from being damaged by ESD Electrostatic Discharge and EMI leakage we strongly recommend the use of CE compliant industrial enclo sure products Technical Support and Assistance 1 Visit the Advantech web site at http support advantech com cn where you can find the latest information about the product 2 Contact your distributor sales representative or Advantech s customer service center for technical support if you need additional assistance Please have the following information ready before you call Product name and serial number Description of your peripheral attachments Description of your software operating system version application software etc A complete description of the problem The exact wording of any error messages Document Feedback To assist us in making improvements to this manual we would welcome comments and constructive criticism Please send all such in writing to support advan tech com lil EKI 1331 User Manual Safety Instructions 10 11 12 do 14 15 16 17 Read these safety instructions carefully Keep this User Manual for la
59. vailable options are auto 2G only and 3G only Enable a static IP if your SIM card can get a static IP address It may be set to either Always Online On Demand or Manual When a dialup fails EKI 1331 will redial after an interval 7 tt Connect Used for advanced parameters 24 ESER Default Enable ALL Enable Customer Unicom QOF or QQ 41 GPRS GPRS Auto 2G only 3G only Disable Always Online 30 seconds N A PIN code Dial Timeout MTU MRU TX Queue Length Authentication Type Enable IP header compression Use default asyncmap Use Peer DNS Link Detection Interval Link Detection Max Retries Debug Expert Option ICMP Detection Server ICMP Detection Interval ICMP Detection Timeout ICMP Detection Max Retries Set the use of the SIM card PIN code Set dialup timeout The EKI 1331 will reboot after timeout N A 120 seconds Set max transmit unit or max frame size Set this number to 1500 for normal frames and larger for 1500 little big frames Set max receive units 1500 Set length of transmit queue 64 Select either Auto PAP or CHAP This is nesse Auto cary for some ISP connections Enable IP header compression Enable Enable default asyncmap and PPP advanced Disabled option Use the assigned DNS server Enable Set the Link Detection Interval 55 seconds Set the max retries if a link detection f
60. ystem Network SENKES Firewall Dos VPN 1906 status e pent Cal DMZ EP Enable DMZ at ALS Host Source Address Range Optional Example 1 1 1 1 1 1 1 024 1 1 11 2222 Apply Cancel The page description is shown below Parameters Description Default Enable DMZ Check to enable the DMZ Disabled DMZ Host Set the host IP of a DMZ Blank EE Set a range of restricted source IP addresses Blank The EKI 1331 s management port should never be mapped to a DMZ MAG IP Bundling When a firewall denies all access to the external network only a PC with MAC IP bundling can access the internet From the navigation panel select Firewall gt gt MAC IP Bundling then enter the MAC IP Bundling page as shown below The device supports up to 20 MAC IP bunding entries ADNANTECH Enabling an Intelligent Planet System Network Services Firewall Qos VPN Tools Status MAC IP Bundling MAC Address IP Address Description 00 00 00 00 00 00 192 168 2 2 Apply Cancel The page description is shown below Parameters Description Default MAC Address Set the bundling PC s mac address 00 00 00 00 00 00 IP Address Set the bundling PC s IP address 192 168 2 2 Description Describe this configuration Blank EKI 1331 User Manual 44 3 6 3 6 1 QoS This chapter covers QoS or Quality of Service QoS is a set of services that ensures bandwidth availability for sensitive applications These services includes bandwidth control and IP ba

User Manual EKI-1331 - download.advantech.com

Contents

Download Pdf Manuals

Related Search

Related Contents