MF910L Quick Start Guide
Contents
1. Internet Wi Fi Mode Your device can be connected to a WLAN device such as a hotspot device or wireless router through Wi Fi to access the Internet The WLAN device must be already connected to the Internet NOTE Your device and the WLAN device must be in different subnets Installing Your Device 1 Open the U SIM card cover NOTE Do not remove the cover rudely because it is connected with the device 2 Install a U SIM card to the U SIM card slot Q WARNING Your device does not support the micro SIM card and nano SIM card or any other non standard SIM cards To avoid damage to the device do not use those cards or any card holders 3 Close the U SIM card cover Connecting to Your Device Using Wi Fi 1 Power on your device 2 Make sure your computer or other client devices have enabled Wi Fi and search for available wireless networks NOTE Refer to your Wi Fi enabled client device manual for further details on how to search for wireless networks If you use a computer you need to set your computer to obtain an IP address automatically 3 Select the Wi Fi name SSID of your device and click Connect 4 Enter the Wi Fi password if necessary and click OK NOTE Refer to the chapter Getting to Know the Wi Fi SSID and Password to get the default Wi Fi SSID and password 5 Wait until the client device is connected to your device successfully Using a USB Cable 1 Connect a computer to2. phrase in the Pass Phrase text box and click Apply gt Click Add enter the Wi Fi hotspot information in the Add Wi Fi Hotspot area and click Apply Add Wi Fi H Network Name SSID Security Mode WPAZ PSK I WPA Algorithms TKIP AES AUTO Pass Phrase Display Passwon After the client device is connected to the Wi Fi hotspot successfully you can access the Internet Configuring Your PC The following procedure describes how to configure the Internet Protocol in the Windows 7 operating system for your Wi Fi connection 1 Right click Network and select Properties 2 Select Change adapter settings 3 Right click Wireless Network Connection and select Properties 4 Select Internet Protocol Version 4 TCP IPv4 and click Properties 5 Select Obtain an IP address automatically and Obtain DNS server address automatically and click OK Warning and Notice To the Owner If inadequately shielded some electronic devices for example the electronic system of vehicles may be affected by the electromagnetic interference caused by the device Consult the manufacturers of such devices before using the device if necessary Operating the device may interfere with medical instruments such as hearing aids and pacemakers Always keep the device more than 20 centimeters away from such medical instruments when your device is powered on Power off the device if necessary Consult a physician or the manufact
3. ZTE MF910L Quick Start Guide ZTE CORPORATION NO 55 Hi tech Road South ShenZhen P R China Postcode 518057 Getting to Know Your Device Getting to Know Your Device Getting to Know Your Device Getting to Know Your Device Installing Your Device Connecting to Your Device Appearance The following figure is for your reference only Power Key 2 WPS Key e Press and hold for 3 seconds to activate the WPS function e Press to view the Wi Fi SSID and password on the LCD screen 3 U SIM Card Cover and Reset Hole 4 LCD Screen 5 Charging micro USB Jack Indicators When the device is powered on the following icons may be displayed on the LCD screen For a description of the icons refer to the following table Icon Description il Network signal strength Network system type The 4G 3G or 2G icon is displayed on the LCD 2G 3G 4G ers screen depending on the connected network slp The user is in roaming status Connected to the Internet received IM One or more new messages are I lt Wi Fi status and the number of ma connected users Battery level Connection Scenarios The device can access the Internet in two ways and it allows multiple clients to surf on the Internet at the same time The following figures are for your reference only 4G Mode A U SIM card can be used to access the Internet
4. aves because signal reception may be affected The device is not waterproof Keep the device dry and store it in a shady and cool place Do not use the device immediately after a sudden temperature change because dew may be generated inside and outside the device Do not use it until it becomes dry Handle the device carefully Do not drop bend or strike it Otherwise the device may be damaged Only qualified personnel can dismantle and repair the device An operating temperature between 10 C and 45 C and humidity between 5 and 95 are recommended Using Battery Do not change the built in rechargeable battery in your device by yourself The battery can only be changed by ZTE or ZTE authorized service provider Limited Warranty This warranty does not apply to defects or errors in the product caused by i Reasonable abrasion i End users failure to follow ZTE s installation operation or maintenance instructions or procedures iii End users mishandling misuse negligence or improper installation disassembly storage servicing or operation of the product iv Modifications or repairs not provided by ZTE or a ZTE certified individual v Power failures surges fire flood accidents and actions of third parties or other events outside ZTE s reasonable control vi Usage of third party products or usage in conjunction with third party products if such defects are due to the combined usage
5. pdate specifications without prior notice Version No R1 0 Edition Time March 3 2015 Manual No 079584507137 Troubleshooting Troubleshooting Problem Recommended Action Problem Recommended Action i Install the software and run the Ensure that your U SIM card is The connection i i installation program in the My available between your The client Computer Smartbro Pocket Wifi path device and a PC through a USB Ifthe driver of your device is cable cannot be abnormal reinstall the software You established need to uninstall the software first Ensure that the Wi Fi function is The connection enabled between your device and a Refresh the network list and select the correct SSID client through se e Check the IP address and ensure Wi Fi cannot be 2 that your client can automatically established obtain an IP address connected to the device cannot access the Internet Change the location and find a place with good signal Check the settings of the WAN connection mode Contact your service provider and confirm your APN settings The client cannot access the Internet in Internet Ensure that the WLAN device has already been connected to the Internet Ensure that your device and the WLAN page cannot be visited Wi Fi mode device are in different subnets Enter the correct address The default The 4G Mobile address is ht
6. tp 192 168 1 1 or Hotspot K http www smartbrosettings net configuration Use only one network adapter in your PC Do not use any proxy server C 1588
7. uest SSID area 4 Click Apply Accessing the Internet 4G Mode After a client device is successfully connected to your device you can access the Internet in Automatic or Manual mode The default mode is Automatic Mode Operation Your device is automatically connected Automatic to the Internet and you can surf on the Internet through the client Accessing the Internet Accessing the Internet Configuring Your PC Warning and Notice Warning and Notice Warning and Notice Warning and Notice 1 Log in to the 4G Mobile Hotspot configuration page 2 Select Settings gt Network Settings gt Dial up Settings gt WAN Connection Mode gt Manual and then click Apply 3 Select Home and click Connect or Disconnect Manual NOTE To modify the parameters of your device log in to the 4G Mobile Hotspot configuration page Internet Wi Fi Mode 1 Log in to the 4G Mobile Hotspot configuration page 2 Select Settings gt Internet Wi Fi 3 Set the Internet Wi Fi Switch and Preferred Network and click Apply 4 You need to set Internet Wi Fi Switch to Enable and Preferred Network to Wi Fi Internet Wi F Internet W Fi Switch Enable Disable Preferred Network WLFi O WWAN Current Status WAN connected 5 Connect to the Wi Fi hotspot The following two methods are for your reference gt Select a Wi Fi hotspot listed in the Wi Fi Hotspot area enter a pass
8. urers of medical instruments before using the device if necessary Be aware of the usage limitation when using the device at places such as oil warehouses or chemical factories where there are explosive gases or explosive products being processed Power off the device if necessary Do not use electronic transmission devices in aircrafts at petrol stations or in hospitals Observe and obey all warning signs and power off the device in these conditions Do not touch the inner antenna area unless necessary Otherwise the performance of the device may be affected Do not use the device in an enclosed environment or where heat dissipation is poor Prolonged work in such space may cause excessive heat and raise ambient temperature which may lead to automatic shutdown of the device for your safety In the case of such event cool the device in a well ventilated place before turning on for normal use Keep the device out of the reach of small children The device may cause an injury if used as a toy When the device is operating do not touch the metallic parts Failing to do so may cause burns To the Users Use original accessories or accessories that are authorized Using any unauthorized accessories may affect the performance of the device and violate the related national regulations about telecom terminals Avoid using the device near or inside metallic constructions or establishments that can emit electromagnetic w
9. vii Any other cause beyond the range of normal usage intended for the product End users have no right to reject or return the product or receive a refund for the product from ZTE under the above mentioned situations This warranty is end users sole remedy and ZTE s sole liability for defective or nonconforming items and is in lieu of all other warranties expressed implied or statutory including but not limited to the implied warranties of merchantability and fitness for a particular purpose unless otherwise required under the mandatory provisions of the law Limitation of Liability ZTE shall not be liable for any loss of profits or indirect special incidental or consequential damages resulting from or arising out of or in connection with using of this product no matter whether or not ZTE had been advised knew or should have known of the possibility of such damages including but not limited to lost profits interruption of business cost of capital cost of substitute facilities or product or any downtime cost LEGAL INFORMATION Copyright 2015 ZTE CORPORATION All rights reserved No part of this publication may be excerpted reproduced translated or utilized in any form or by any means electronic or mechanical including photocopying and microfilm without the prior written permission of ZTE Corporation The manual is published by ZTE Corporation We reserve the right to make modifications on print errors or u
10. your device with a USB cable 2 Power on your device The operating system detects and identifies new hardware and automatically installs the hardware NOTE If the system does not automatically launch installation you can run the installation program in the My Computer Smartbro PocketWifi path 3 Wait until the computer is connected to your device successfully Getting to Know the Wi Fi SSID and Password You can use the following methods to get the default Wi Fi SSID and password e View the label on the device e Press the WPS Key The Wi Fi SSID is displayed on the screen NOTE Your device don t have Wi Fi connection password it will keep turning on Logging in to the 4G Mobile Hotspot Configuration Page 1 Make sure the connection between your device and the client device is correct 2 Launch the Internet browser and enter http 192 168 1 1 or http www smartbrosettings net in the address bar NOTE It is recommended that you use IE 7 0 or later Firefox 15 0 or later Opera 10 0 or later Safari 4 0 or later or Google Chrome 10 0 or later 3 Enter the password to log in to the 4G Mobile Hotspot configuration page NOTE The default password is smartbro Changing the Wi Fi SSID or Pass word 1 Log in to the 4G Mobile Hotspot configuration page 2 Select Settings gt Wi Fi Settings gt Basic Settings 3 Change the Network Name SSID or the Pass Phrase Password in the Main SSID G
Download Pdf Manuals
Related Search