PROFESSIONAL EXTRACTOR HOOD
Contents
1. PROFESSIONAL EXTRACTOR HOOD For original parts amp reliable service USER MANUAL INSTALLATION INSTRUCTIONS CE Table of Contents From the Manufacturer Specifications SAFETY Read this first Vent System Requirement Description of Parts Ducted mode Installation Electrical Connection Operation Cleaning amp Maintenance Troubleshooting Schematic Diagram 8 9 10 11 13 14 15 Schematic Diagram Electronic Control PCB Troubleshooting From the Manufacturer e This appliance and it s packaging are produced by processes that minimize waste and respect the Symptoms Possible Cause Action environment Check that the plug e Please help us to continue the protection of the Does not function No electrical supply is connected environment by disposing of the packaging in a correct Check that the main manner switch is turned on e Safety Aluminum grease Clean the filters and e Please do not allow young children to play with the plastic Poor airflow filters clogged replace when dry bag packaging Gharcoal grease Replace charcoal e Before disposing of any old appliances be sure to cut off the power chord so that others will not be endangered by a filters clogged filters with new sets f defective electric appliance Motor running but Butterfly valve Contact technician no aio jammen Specifications High temperature The kitchen is not l E Input 220 240V 50Hz Motor cuts after a safety devic2. 3 speed control Use the low speed for simmering medium speed for light cooking Use the high speed for frying or heavy cooking It is also equipped with a light bulb to illuminate you cooking area when needed Q 12 P 2 r oan b D i aoe eters a En eae E or F ii iii Light On Off Button i On Off switch for the light Push the button in to turn the light ON push again to turn the light OFF Blower On and Speed Buttons ii iii amp iv Button ii operates the blower on LOW speed push again to turn off Push button iii for MEDIUM speed push again to turn off Push button iv for HIGH speed push again to turn off SAFETY Read this First Continued Service agent or similarly qualified persons in order to avoid a hazard e There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels not applicable to appliances that only discharge the air back into he room e There is a fire risk if cleaning is not carried out in according with the instructions e Do not flamb under the range hood e The appliance use 4 hob element at most Vent System Requirements Determine which venting method is best for your application Vented non re circulating system must be terminate to the outside Ductwork can extend either through the wall or the roof Do not terminate the vent system in an attic or other enclosed area The leng
3. e activated sufficiently ventilated 3 Absorption few minutes The hood is installed too The hood must be near the cooking stove least 65cm from stove e Motor version 1X 135W Charcoal filters not In re circulating mode e Lamps 2 X 20W Strong cooking installed charcoal filters must be Total Power 175W smell installed Aluminum grease filter Wash the aluminum External Dimensions Oil dripping onto saturated grease filters e 60cm version 598 500 140mm stove i Aluminum grease filter Wash the aluminum e 70cm version 698 500 140mm Raltaied grease fiers e 90cm version 898 500 140mm Whirring sound Foreign object in contact Contact technician with fan blade SAFETY Read this First Do not connect the appliance if there are obvious signs of transportation damage Read this user manual thoroughly before attempting to use this appliance Installation and repair should be attempted only by qualified technical personnel It is dangerous to modify any part of this appliance The manufacturer declines all responsibility in case of failure to adopt proper safety measures Ensure the location in which this appliance is installed has good permanent ventilation The distance between the bench top to the lower part of the hood must not be at less than 65 cm or higher than 75 cm Use an electrical connector with earth that is correct for your location Check that the voltage in your area is correct before plugging in The electrical connection o
4. f this appliance Blue NEUTRAL Brown LIVE Multiple plugs and extension cables must not be used Overload is dangerous and may cause a fire Ensure that the power supply chord is free from any heat source or sharp objects The appliance should be switched off and the electrical supply disconnected before any cleaning or maintenance work can be carried out This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance If the supply cord is damaged it must be replaced by the manufacturer its Cleaning amp Maintenance SURFACES Wash with warm soapy water and a soft sponge Never use abrasive detergent scouring pads steel wool or solvents on any part of this appliance as this will cause irreparable damage Aluminum Grease Filters Wash in the dishwashers or soak the panels in a degreasing agent for an hour then rinse off LIGHT BULB REPLACEMENT Before attempting to replace the light bulb make sure that the light switch is turned off Remove the grease filter to access the lamp area Remove the damaged light bulb and replace with an incandescent oval bulb maximum 20W 13 12 Operation The hood is equipped with
5. n 3mm Appliance without plug Fit an approved plug or an bi polar switch with a minimum contact opening of no less than 3mm The manufacturer are not liable for any problems caused by the user s failure to observe the above instructions Installation 2 STEP 1 Remove the aluminum filters and place them in a safe location to avoid damage STEP 2 Hang the hoods first and then Install the 2 screws in the wall through the inside of the hoods like below picture showed STEP 3 Turn the screws clockwise until locked Finished Ducted mode A DUCTED MODE VENTED MODE e Inthe ducted mode cooking fumes are vented outdoors through suitable connection of 125mm diameter In this mode only the aluminum filters are installed i alternative _ M outlet aluminium filters Installation 1 Installation 1 Continued STEP 1 Remove the aluminum filters and place them in a safe location to STEP 3 Hang the hood on the 2 screws avoid damage wall Li STEP 4 Tighten the 2 screws completely STEP 2 Install the 2 screws on the wall wall aaa Y amp 818 cm for 90 cm hood r 33 8 cm far 60 cm haad ES SISIL LLLI LILLI Finished
6. th of the ductwork and the number of elbows should be kept to a minimum to provide efficient performance The size of the ductwork should be uniform Do not install two elbows together Use duct tape to seal all joints in the ductwork system Use caulking to seal exterior wall or floor opening around the cap Flexible ductwork is not recommended Flexible ductwork creates back pressure and air turbulence that greatly reduces performance Make sure there is proper clearance within the wall or floor for exhaust duct before making cutouts Do not cut a joist or stud unless absolutely necessary If a joist or stud must be cut then a supporting frame must be constructed Description of Parts A DUCTED MODE _connector control switch Aluminium filters Electrical Connection Before completing any connection make sure the house voltage corresponds with the voltage indicated on the label affixed inside the hood It is advisable to call a qualified technician to make the electrical connection Appliance fitted with plug Connect it to a socket which conforms with current regulations If you intend to connect it directly to the electric mains remove the plug and fit an approved bipolar switch with a minimum contact opening of not less than 3mm If the plug is not accessible once it has been inserted in the socket it will however be necessary to fit an approved bipolar switch with a minimum contact opening of no less tha
Download Pdf Manuals
Related Search