DIB-2A - Farnell
Contents
1. PULSE DIB 2A DUAL ACTIVE DIRECT BOX O O O No OO omas 40 300W 83M0 9V BATTERY O e LNdLNO INPUT 2 O g Od PULSE WNIDIS EN WN N 6 O L LNdLno INPUT 1 6 O DIB 2A Dual Active Direct Box a ER HON 40 TT O ONS aSvVHd LOH mM asaa3nat O QL O O O DIB 2A Thank you for having chosen an pulse DIB 2A before you initial start up please make sure that there art no transpor damages Shoud there be any do not take the device into operation and imnediately consult your dealer FEATURE 1 Converts 50K Ohms instrument input into balanced mixer outputs 2 Power supply via 9V battery 3 Ground lift switch 4 Switchable signal level 20 0 30dB 5 2low impedance XLR outputs 6 Mono model the signal is splitted from input 1 on both outputs 7 Phase switch 8 Hi Cut switch 8kHz 9 10 Ti Modem convex housing design Full rubber housing comers for safe operation Cables can be routed under the housing OPERATINGDETERMINATIONS 1 16 This device is a DI box transmitting audio signals This product is only allowed to be operated with 1 standard 9V battery and was designed for indooruseonly Batteries are hazardous waste which need to be disposed of appropriately If the device is to be disposed the battery has to be removed first Make sure thatthe poles are correct when inserti2. attery remove the old battery from the battery compartment 4 Leaky or damage batteries might cause cauterization when in contact with the skin therefore use suitable protective gloves 5 Insert the battery and make sure that the poles are correct 6 Replace the battery cover and close it 7 Ifthe device will not be used for a longer period of time remove the battery in order to avoid battery leakage 8 In order to have along battery life you should only use alkali batteries SPECIFICATIONS Power supply 1 standard 9V battery Current consumption approx 65mA Battery life 6 8 hours Frequency range 10Hz 30kHz Input impedance 470KOhms Output impedance 600 Ohms Maximum output level 6dBu Dynamic range gt 100dB Hi Cut 8kHz Input Connectors XLR mounting sockets Output Connectors XLR mounting plug THD 0 5 Dimensions 150x130x60mm Weight 0 5kg
3. ce is to be transported Please consider that unauthorized modifications on the device are forbidden due to safety reasons If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void CONNECTIONS f ae 4 9 6 With a Direct Injection Box You can directly take a sound signal from a highly resistant cable e g between guitar and amplifier and send it directly to to the mixer input In order to obtain highest sound quality only use high quality cables for connecting the devices Make sure that the cables are properly fixed Connect you signal source e g guitar bass guitar keyboard etc to the input socket Occupation mono 1 4 jack plug Tip sleeve In Phase Ground If there is noise Please use the Ground Lift switch You can also adapt the Input level 20dBfor extremely low signal levels Odb for e g guitars 30db for line instruments HI CUT With the Hi Cut switch you can activate the low pass filter 8kHz Phase Reverse In order to invert the cable occupation 7 Connect the microphone input of your stage mixer to the output socket OPERATION Balanced XLR socket 1 Ground 2 In Phase 3 Out of Phase i Inserting Replacing the battery 1 Please refer to the explanation under operating Determinations 2 Open the battery cover on the bottom and remove it 3 Ifreplacing the b
4. ng the battery be disposed the battery has to be removed first Never let batteries lying around openly as there in the danger that these can be swallowed by children or domestic animals Immediately consult a doctor when batteries are swallowed Leaking or damaged batteries can cause irritations when getting into contact with the skin In this case use appropriate protective gloves Make sure that the battery cannot be short circuited thrown into the fire and be charged There is a danger of explosion Never spill any liquids on the device Should any liquid enter the device nevertheless remove the battery immediately Please let the device be checked by a qualified service technician before your operate it again Any damages caused by liquids having entered the device art not subject to warranty Donot shake the device A void brute force when operating the device The ambient temperature mist always be between 5 C and 45 C Keep away from direct insulation particularly in cars and heaters The relative humidity must not exceed 50 with an ambient temperature of 45C This device must only be operated in an altitude between 20 and 2000m over NN Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Never use solvents or aggressive detergents in order to clean the device Rather use a soft and damp cloth Please use the original packaging if the devi
Download Pdf Manuals
Related Search