POWER SUPPLY/DMX-512 LED DRIVER
Contents
1. 0 64 0 Blu No strobo 10 0 0 128 0 Blu No strobo 11 0 0 192 0 Blu No strobo 12 0 0 255 0 Blu No strobo 13 64 64 0 0 Yellow No strobo 14 128 128 0 0 Yellow No strobo 15 192 192 0 0 Yellow No strobo 16 255 255 0 0 Yellow No strobo 17 64 0 64 0 Magenta No strobo 18 128 0 128 0 Magenta No strobo 19 192 0 192 0 Magenta No strobo 20 255 0 255 0 Magenta No strobo 21 0 64 64 0 Cyan No strobo 22 0 128 128 0 Cyan No strobo 23 0 192 192 0 Cyan No strobo 24 0 255 255 0 Cyan No strobo 25 64 64 64 0 White No strobo 26 128 128 128 0 White No strobo 27 192 192 192 0 White No strobo 28 255 255 255 0 White No strobo 29 0 0 0 64 Amber No strobo 30 0 0 0 128 Amber No strobo 31 0 0 0 192 Amber No strobo 32 0 0 0 255 Amber No strobo 33 64 0 0 64 Red Amber No strobo 34 128 0 0 128 Red Amber No strobo 35 192 0 0 192 Red Amber No strobo 36 255 0 0 255 Red Amber No strobo 37 0 64 0 64 Green Amber No strobo 38 0 128 0 128 Green Amber No strobo 39 0 192 0 192 Green Amber No strobo 40 0 255 0 255 Green Amber No strobo POWER SUPPLY WIRING DIAGRAM RGB output 6 pin Female Rj12 en Teme MX E T ains 195 265 Vac CONTROLLER DMX IN OUT connectors 50 60 Hz 1 6ND 2 DATA 2 o DATA Dmx address setting 6 1 6 pin Female RJ12 Pin 1 RED Pin 2 RED Pin 3 GREEN Pin 4 GREEN Pin 5 BLUE Pin 6 BLUE RJ12 6P6C 6 pin Male RJ12 6P6C indicates 6 positions 6 cable2. battery press AUTOMATIC and MANUAL keys at the same time and hold until the red led on remote control Is blinking 3 seconds minimum required then 2 Push in this sequece the key P and P atthe end of the sequence the red led blinks 3 times 3 Now the remote control is ready for use Using the remote control Push ON OFF to turn ON and OFF all leds at the same time or to continue a previously automatic sequence if activated Manual Control allows the user to select the color RED GREEN or BLUE by pushing P or P buttons Everytime you push the buttons a flash will appear on the selected color either RED GREEN or BLUE Push P or P once more to increase or decrease the brightness of the selected color Automatic control will run a pre programmed sequence The sequence will go through all colors one by one To exit from automatic mode press MANUAL control INFRARED REMOTE CABLE This cable with infrared sensor must be connected on CN 2 infrared port ofthe power supply and can not be longer than actual lenght WARNING the power supply must be turned off before connecting the cable The receiver must be visible by remote control and protected from direct sun light Setting up the infrared receiver Plug the cable on CN3 of the power supply and set to ON position DIP n 10 Turn on the board all leds will be turned OFF Choose the desired functions using the remote control CN 2 Remote infrared conn
3. POWER SUPPLY DMX 512 LED DRIVER Code 03 LA 002 User s manual V 1 20 ENG 1GNnD 2 DATA 3 DATA The Lighting Company IMPORTANT SAFETY INFORMATION Fire prevention Never locate the fixture on any flammable surface Minimum distance from flammable materials 10 cm Replace any blown or damaged fuses only with those of identical value Connect the Power Supply to main power via a thermal magnetic circuit breaker Prevention from electric shock High voltage is present inside the unit Unplug the unit prior to performing any operation which involves touching the inside of the unit This equipment must be grounded do not connect to non grounded supplies Use only AC supplies 195 265V 50 60Hz The unit should never be located in position exposed to rain or in areas of extreme humidity A good air ventilation is essential for proper equipment work Safety The external surface of the unit may exeed 50 C never handle the unit until at least 5 minutes have elapsed since the unit was turned off Never install the unit in an enclosed area lacking sufficient air flow The ambient temperature should not exeed 40 C and should not be lower than 10 C DESCRIPTION The Power supply DMX 512 LED driver is a unit dedicated to the following LED products by D T S MR16 RGB LED lamp MR16 full color LED lamp D30 RGB LED projector D30 full color LED projector 3 channels output DMX 512 Power interface able to dri
4. ector Note Note The information contained in this publication has been carefully prepared and checked However no responsibility will be taken for any errors All rights are reserved and this document cannot be copied photocopied orreproduced in partor completely without prior written consent from DTS DTS reserves the right to make any aesthetic functional or design modifications to any of its products without prior notice DTS assumes no responsibility for the use or application of the products or circuits described herein MADE IN ITALY C The Lighting Company D T S Illuminazione s r l Via Fagnano Selve 10 12 14 47843 Misano Adriatico RN Italy Tel 39 0541 611131 Fax 39 0541 611111 _ info dts lighting it www dts lighting it
5. mode and the dip switches from number one up to nine are used for address selection INFRARED activates the remote control and can only execute incoming commands from the infrared control ALL COLORS ON all channels are activated at the maximum level all colors are on AUTO EFFECT Activates one of internal pre programmed sequence that changes colors and loops as long as the board is supplied DMX PROTOCOL DMX CHANNEL DESCRIPTION GREEN RED BLUE NOT USED STROBE SYNC STROBE STROBE DELAY NOT USED ONO akwnhd COLOR PALETTE In the table is shown the address of each color combination The color combination will run automatically every time the power supply is turned on The palette number is the address in binary code obtained by the sum of the first 6 DIP switches Dip switch ON OFF Value 1 1 C 2 C 4 C 8 C 16 6 CC 32 C Off CI On CI On 10 CH On Making a sum of DIP switches you can have the desired palette address Example To select Green color palette n 5 You have to switch on DIP n 1 and DIP n 3 Palette numb Red Green Blue Amber 0 0 0 0 0 Off 1 64 0 0 0 Red No strobo 2 128 0 0 0 Red No strobo 3 192 0 0 0 Red No strobo 4 255 0 0 0 Red No strobo 5 0 64 0 0 Green No strobo 6 0 128 0 0 Green No strobo 7 0 192 0 0 Green No strobo 8 0 255 0 0 Green No strobo 9 0
6. s Modular Plug 123456 LEDs cabling connection can be done with a standard UTP TIA EIA 568 A category 3 cable The maximum distance between power supply and the last LED lamp in the line should not exceed 100 meters For short distance connections less than 20 meters you can also use a standard 6 conductors telephone flat cable POWER SUPPLY WIRING CONNECTIONS Pin 1 m men D T S T BOX CODE 03 LA001 INPUT OUT 2 LINO cg InO LNdNI xog L AAA OUT 1 IMPORTANT The minimum number of MR16 RGB 3W LED lamps connectable to the D T S Power supply is 3 pcs The maximum number of MR16 RGB 3W LED lamps connectable to the D T S Power supply is 12 pcs Never plug the cable coming from the Power supply into OUT 1 or OUT 2 of the T BOX when other MR16 lamps are connected because a wrong connection can seriously damage the lamps 3 z Never plug in a new MR16 lamp when the power C supply is turned on m e N E 12 E I MR16 RGB Spot lenses Code 0505L004 MR16 RGB Medium flood lenses Code 0505L005 MR16 RGB Wide flood lenses Code 0505L006 REMOTE CONTROL Color select UP Decrease LED Brightness crease LED Brightness Manual Mode Color select Down Automatic Mode This remote control need to be set up at the first use for right infrared protocol please proceed as follows 1 Insert the
7. ve up to 12 x 1W RGB LED units 3 x 350mA electronically dimmable led control outputs Main Input voltage range is 195V 265V 50 60 HZ It is possible to use this item through every DMX 512 mixer or by using the DTS InfraRed control MAIN ELECTRICAL CHARACTERISTICS Input Voltage Range Vin 195 265 Vac Frequency 50 60 HZ Power Consumption Range 6 50 W Power Factor Pf 0 95 electronic PFC controller Efficiency 90 typical Output Power Output Range 4 8 12W per channel Output Current 350 mA 100 per channel Output Voltage Vout 48V Max Load output 12 x MR16 RGB LED lamp or 12 x D30 RGB LED projector or 4 x MR16 full color LED lamp or 4 x D30 full color LED projecto Min Load output 3 x MR16 RGB LED lamp Control Input Control Signal DMX 512 Dimming System Constant Current PWM Address Range DMX 512 channels addressable by 9 DIP switches APPLICATIONS Cinemas Restaurants and pubs Discoteques Architectural Interior and Exterior SPECIAL FUNCTIONS By the activation of DIP number 10 some special functions are activated Those are Infrared receiver Automatic effect generator Fixed colour palette preset In the table below is explained how the DIP Switches combination works Off Off Off 10 CH of On DMX Off Off On On ON OFF C C C C C H DMX Infrared All colors on CE C C CE Color sdection Auto Effect Palette color Activates the DMX
Download Pdf Manuals
Related Search