User Manual - B&H Photo Video Digital Cameras, Photography
Contents
1. RAYA is a registered trademark of the Gradus Group 2014 Gradus Group LLC All Rights Reserved2. Sound control a Turns the confirmation sounds on and off Slave button a Activates slave mode Slave mode indicator lights a Indicates which slave mode is activated Power output buttons a Increases or decreases the power output of the monolight Modeling light button a Turns the modeling light on or off Modeling light indicator light when button is pushed a Bottom green light on modeling light button turns on default position b Indicates that modeling light intensity level is proportional to the flash tube 8 Modeling light independent indicator light when up or down arrow button is pushed a Top light on model light button goes on b Indicates that the modeling lights intensity level is independent of the flash tube s output 9 Modeling light intensity level up and down arrow adjustment buttons a Adjusts the intensity level of the modeling light b Turns on independent model light mode and overrides proportional mode as displayed in blinking numbers DIGITAL CONTROL PANEL GUIDE LED Screen Guide Steady Numbers Steady numbers indicate the monolights flashtube power output as controlled by the power level buttons HH Blinking Numbers Blinking numbers on the LED screen indicate the intensity levels of the modeling light during adjustment as controlled by the modeling light output buttons VW The numbers only blink when the
3. The Raya SDR 400 includes a user replaceable flash tube and modeling lamp Be careful not to touch the flash tube with your bare hands since this could cause damage to it Please use cotton gloves or a soft dry cloth when touching or handling the flash tube The Raya 150W modeling lamp is a halogen bulb within a glass sleeve You may touch this glass without cotton gloves However wiping it with a cotton cloth after handling it is recommended The monolight comes with a protective cap Always remove the protective cap before plugging in or powering on the unit To remove the cap hold down the mount release and turn the cap counterclockwise Pull the cap from the mount and place it to the side for later use GENERAL OPERATION INSTRUCTIONS To begin using the monolight do the following NOTE Ensure the power switch is set to OFF before connecting the monolight s power cord 1 Plug the cord into the AC wall outlet then plug the connector into the AC input on the flash unit Power on the monolight by flipping the power switch located on the back of the unit Turn on the modeling light using the modeling light button For more information about how to operate the modeling light refer to the Setting the Modeling Light Power Output section on page 24 Connect your camera to the monolight to begin triggering CONNECTING YOUR CAMERA TO THE MONOLIGHT The Raya SDR 400 Alpha Monolight has two
4. triggering options out of the box wireless and sync cord connections Please reference the following instructions to connect your camera to the monolight Wireless The Raya SDR 400 has an integrated four channel wireless receiver Using the included transmitter you can wirelessly trigger your flash unit from up to 65 feet away No line of sight is reguired for your monolight to communicate with the transmitter Use the following instructions to set up and wirelessly trigger your flash 1 Locate the DIP switches on the back of the monolight 2 Set the channel frequency of your choosing 3 On the transmitter set the DIP switches to the same channel as on the monolight 4 Press the test button on the transmitter to fire the monolight Please reference the following chart for channel settings Channel al For wireless triggering of the monolight s flash by pressing the camera s shutter button open the remotes tightening ring by turning it clockwise Slide the remote into your camera s hot shoe and turn the tightening ring counterclockwise to secure Sync Cord The back of your monolight has a 3 5 mm sync input which is used for a hardwire connection between your camera and the flash unit Use the following instructions to connect your two devices 1 Insert the included 11 sync cable s mini plug into the monolight s 3 5 mm sync cable port Connect the PC connector end into your cam
5. modeling light intensity level is being adjusted It will stop blinking after four blinks Confirmation When the monolight s sound is turned off and the modeling light is turned on the modeling light will turn off after a flashtube triggering and come back on once the unit has recycled providing a visual confirmation that the unit is ready to flash again at 100 INSTALLATION amp REPLACEMENT GUIDE The Modeling Light The Raya SDR 400 comes with a 150W 110V halogen model lamp bulb To remove an old bulb and install a replacement bulb do the following 1 Ensure the monolight is powered off and unplugged 2 Using a cotton glove or soft dry cloth carefully unscrew the modeling light bulb 3 With the cotton glove or soft dry cloth pick up the replacement tube 4 Insert the back end of the bulb into the modeling bulb socket and turn it clockwise until secure NOTE The SDR 400 has built in SSC Soft Start Circuitry to ensure longer modeling lamp life When the modeling lamp is turned on it will light up at a minimum brightness and slowly reach full power output This feature prolongs the life of the modeling lamp The Flash Tube The Raya SDR 400s flash tube is user replaceable To replace the flash tube do the following 1 Discharge the flash unit by pressing the test button 2 Power off the monolight and unplug the power cable from the flash unit and power source 3 After 15 minu
6. solely to repair or replacement at the provider s discretion of any product that fails during no rmal use of this product in its intended manner and in its intended environment Inoperability of the product or part s shall be determined by the warranty provider If the product has been disc ontinued the warranty provider reserves the right to replace it with a model of eguivalent guality and function This warranty does not cover damage or defect caused by misuse neglect accident alteration abuse improper installation or maintenance EXCEPT AS PROVIDED HEREIN THE WARRANTY PROVIDE ANY IMP TO ANY FITNESS rights tha To obtain Departme R MAKES NEITHERANY EXPRESS WARRANTIES NOR LIED WARRANTIES INCLUDING BUT NOT LIMITED IMPLIED WARRANTY OF MERCHANTABILITY OR FOR A PARTICULAR PURPOSE This warranty provides you with specific legal rights and you may also have additional vary from state to state warranty coverage contact the Raya Customer Service nt to obtain a return merchandise authorization RMA number and return the defective product to Raya along with the RMA number and proof of purchase Shipment of the defective product is at the purchaser s own risk and expense For more information or to arrange service visit rayalighting com or call Customer Service at 212 594 2353 RAYA A Gradus Group Brand Product warranty provided by the Gradus Group www gradusgroup com
7. deling light output setting The numbers will continue to blink while adjusting the setting Once the desired number is selected the numbers will blink four times then return to the solid monolight power output numbers NOTE Each button press changes the power output by one tenth unit To increase or decrease the numbers displayed on the screen faster hold down the adjustment button Auto Power Dump When lowering the power level the monolight will automatically discharge a flash when the new setting is confirmed Do not look into the flash tube area when performing this change SLAVE AND PRE FLASH SETTINGS The Raya SDR400 Alpha Monolight has five slave settings You can toggle between the modes by repeatedly pushing the slave button until the reguired number is indicated by the light on the right side of the panel Default Setting No LED light is activated Slave mode is OFF Setting 1 Slave mode ON A single flash from another source will trigger the monolight Setting 2 The monolight will trigger after a half second delay After the first flash from another source the monolight will go into a standby mode and the SDR 400 will trigger at the next flash Setting 3 Monolight will trigger after one preflash Setting 4 Monolight will trigger after two preflashes Setting 5 Monolight will trigger after three preflashes BUTTON GUIDE 1 Test button a Manually triggers the monolight at the current settings
8. ecessary for use outside the US as well as a 220 240V modeling lamp FEATURES Multi voltage 100 240VAC 50 60Hz Built in 4 channel radio receiver for wireless function Includes 4 channel radio transmitter for wireless triggering Lightweight compact and easily transported Durable high guality rubberized polymer housing Easy to view LED power display Intuitive operating Precision light output adjustments of 6 f stops from full to 1 32 in O 1 stop increments Proportional or Independent modeling lamp control 150W 110V quartz halogen modeling lamp Quick recycle time Fast flash duration Fan cooled Adaptive thermal control protects against overheating and overvoltage damage Auto power dump feature Built in optical slave Sync delay and red eye reduction functions Model lamp SSC Soft Start Circuitry Plug in user replaceable flashtube 7 umbrella grid reflector BOX CONTENTS SDR 400 Alpha Monolight Umbrella reflector with 7 grid inset 4 channel wireless transmitter Protective cap AC cord 16 4 9 m Sync cord 11 3 35 m OVERVIEW DoS WN S Mount reflector mount Mount release Modeling light Modeling light socket Flash tube 5 8 stand mount 10 11 12 Umbrella mount Umbrella tightening knob Mount tightening knob Tilt knob Fan Handle bk Pp hk m O NDUNDU Digital Control Pad Remote sensor AC input Fuse bay Power switch S
9. er Voltage Syne Cable Input Length of Included Syne Cord 400 w s 165 10 ISO 100 Full to 1 32 in 1 10 increments 0 2 2 2 Sec 0 2 1 7 Sec Visible or audible confirmation 6 stops E26 27 150W Max SSC Soft Start Circuitry Proportional Independent Off 4 channel built in wireless with included 4 channel wireless transmitter sync cable test button slave sensor 1 1000 400w s 433 MHz 65 20 m Type A23 5600 100k User replaceable plug in tube DC 5V 3 5 mm mini 11 3 35 m Slave Settings Sync delay red eye reduction synchronous Touch Pad Controls Yes Adaptive Thermal Control Yes Accessory Mount S Type Mount Compatibility Circuit Protection 5G10A fuse Weight 3 95 lbs 1 8 kg FCC DISCLAIMER This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CE FE Made in China ONE YEAR LIMITED WARRANTy This RAYA product is warranted to the original purchaser to be free from consumer purchase occurs lat defects in materials and workmanship under normal use for a period of one 1 year from the original date or thirty 30 days after replacement whichever er The warranty provider s responsibility with respect to this limited warranty shall be limited
10. era s PC socket If you camera does not have a PC port an adapter will be required MOUNTING ACCESSORIES Light Stand Mount The SDR 400 Alpha Monolight has a standard 5 8 stand mount with tilt and tightening knobs To mount the monolight on a light stand place the stand mount onto a compatible stand with a standard 5 8 top mount Tighten the tightening knob to secure Turn the tilt knob counter clockwise to adjust the tilt of the monolight Turn the knob clockwise to secure the monolight in place Accessory S Mount The Raya SDR 400 Alpha Monolight has an S Mount for light modifying accessories This can be used with such optional add ons as speed rings for softboxes The included umbrella reflector lines up with the unit s umbrella mount located on the monolight s stand mount To use accessories with the monolight s S Mount simply align the accessory with the mount and insert Once inserted rotate the accessory clockwise to secure To remove it from the mount hold down the mount release and reverse the above instruction Umbrella Mount To mount an umbrella to the monolight first attach the umbrella reflector dish using the above instructions Then run the umbrella rod through the dishs umbrella hole and into the monolights umbrella mount Secure the umbrella using the umbrella tightening knob FLASH SETTINGS Setting the Monolight s Power Output The Raya SDR400 Alpha Monolight s flashtube ha
11. o prevent damage to the internal electronics from over heating over volting and over charging To avoid damaging the unit please follow the information outlined in the Precautions section NOTE The fan turns on when the unit s internal heat reaches 122 F 50 C Error Codes The Raya SDR 400 s LED screen will indicate one of the following codes when it detects an issue E1 One or more of the capacitors is overvolting If this error occurs turn the unit off and let it rest for a few minutes If the error message comes up again contact the manufacturer E2 The monolight is overheating 176 F 80 C The error will disappear once the unit has cooled Press any button except the power button to remove the error message The fan will continue to cool the unit until the heat has dissipated after 5 10 minutes If the monolight is turned off the light will take longer to cool E3 The monolights input voltage is more than 265 volts If this error occurs turn the unit off and let it rest for a few minutes If the error message comes up again contact the manufacturer Power Output Guide Number Output Control Range Recycle Time 100 120V 60Hz Recycle Time 220 240V 50 Hz Flash Ready Indicator Power Range Modeling Lamp Modeling Lamp Control Triggering Method Flash Duration Frequency Effective Wireless Distance Range Battery Replacement for Transmitter Color Temperature Flash Tube Trigg
12. raya SDR 400 USER MANUAL Thank you for choosing the Raya SDR 400 Alpha Monolight This all in one fan cooled 400w s monolight uses intelligent technology creating a sleek compact and easy to use flash unit Constructed with a high quality rubberized polymer housing the SDR 400 is operated with a clearly marked digital control panel creating a simple and intuitive workflow for controlling everything from power levels in one tenth stop increments to the built in wireless receiver The durable SDR 400 has an integrated four channel wireless receiver that communicates with an included wireless transmitter You can easily change the wireless frequency of the monolight with DIP switches Additionally the monolight includes five individual slave settings ranging from a regular slave mode to modes that will trigger the unit with external flashes with up to three pre flashes The Raya SDR 400 Alpha Monolight is equipped with advanced protection circuit controls to prevent several types of common high voltage electronics issues including over heating over volting and over charging This Raya studio flash is ideal for photography enthusiasts looking for an economical high powered flash unit with the convenience of wireless triggering The unit s auto seeking multi voltage 100 240V 50 60 Hz circuitry and compact construction make this monolight ideal for local and international use an AC plug adapter will be n
13. s a 6 stop power range represented by a 10 60 numbered scale on the LED screen To increase the power output of the monolight press the HH button on the back of the flash unit To decrease the power output press the H button NOTE Each button press changes the power output by one tenth of a unit To increase or decrease whole numbers displayed on the screen at a faster pace hold down the adjustment button Setting the Modeling Light Power Output The Raya SDR400 Alpha Monolight has a 150 watt user replaceable modeling light The modeling lights power output is represented by a 10 60 numbered scale on the LED screen To increase the modeling lights power output press the button To decrease the output press the Y button The modeling light has two indicator lights Proportional When the model light is turned 170 on the default setting is proportional as Ess indicated by the bottom green light As you adjust the monolights power output using the HH or H buttons the modeling light will adjust up or down proportionally This gives you the general idea where highlights and shadows will fall in relation to the flash power Independent To change from the default wW setting press the up or down arrow once XX The top green light will glow green and the SO bottom green light will disappear Blinking numbers will appear on the LED screen displaying the current mo
14. tes remove the modeling lamp and any other accessory connected to the unit 4 Wearing a pair of cotton gloves or using a soft dry cloth and using a pair of needle nose pliers carefully unhook the retention spring loop of the flash tube Make sure it is disengaged from the flash tube 5 Once itis unhooked grip the base of the flash tube on each side and carefully pull it from the monolight 6 Pick up the new flashtube and push its pins into the sockets using firm even pressure at the base 7 With needle nose pliers hook the retention spring over and above the flash tube 8 Reinsert the modeling lamp then any other accessory to the monolight Replacing the Fuse The Raya SDR 400 comes with two fuses one installed and one spare Both are located within the fuse bay To remove the fuse housing from the fuse bay and replace the fuse do the following 1 Ensure the monolight is powered off and unplugged 2 Using a flat head screwdriver lift the fuse housing from the nook found on the flat side of the AC jack 3 The fuse located within the housing is the one the monolight is using when it is powered on To replace the fuse remove it from the box 4 Replace it with a spare 5 Reattach the fuse holder to the fuse bay to complete the process MAINTENANCE NOTES Adaptive Thermal Control The Raya SDR 400 Alpha Monolight is equipped with protection circuits t
15. ync cable port DIP switches Remote 20 Test button 21 DIP switches 22 Shoe foot 23 Tightening ring 24 3 5 mm port PRECAUTIONS A Please read and follow these instructions and keep this manual in a safe place Keep this product away from water and any flammable gases or liquids Make sure this product is turned off when plugging it into an electrical outlet Use only the correct recommended voltage Do not attempt to disassemble or repair this product There are components inside that can produce a hazardous electric shock Handle this product with care Do not stare at the lights when they are powered on Avoid rapid high power flashing Excessive heat shortens the life span of flash tubes modeling lamps and internal components If not used for two months turn the unit on for 30 minutes and fire the flash several times to charge the capacitors Always remove the protective cap before plugging in or powering on the unit Never operate the flash with the protective cap on Clean this product with only a soft dry cloth Always wear cotton gloves when handling the flashtube Never open or do repairs on the unit There are no user serviceable parts Keep this product away from children Make sure everything is secure before proceeding Make sure that this product is intact and that there are no missing parts before use All photos are for illustrative purposes only PREPARING FOR USE
Download Pdf Manuals
Related Search