Industrial Lite-Managed PCI Ethernet Switch Card
Contents
1. and Keep current username amp password to prevent IP username and password been reset to default ORing Industrial Networking Corp 28 amp eM sss ICS4040 Users Manual BEEN 4 1 11 System Reboot System Reboot Please click Reboot button ta restart switch device System Reboot interface ORing Industrial Networking Corp 20 e orna ICS 4040 User s Manual Technical Specifications Technology Ethernet Standards IEEE802 3 10BASE T IEEE802 3u 100BASE TX IEEE802 3x Flow Control and Back pressure IEEE802 1D Spanning tree protocol IEEE802 1w Rapid Spanning tree protocol STP RSTP O Ring Ring redundancy ESSE ouple Ring Dual Homing Fast recovery mode Windows 95 NT 98 2000 ME XP 2003 Vista 32 bit Driver Support Novel NetWare 3 and above Linux 2 4 x 2 6 x WINCE 4 0 5 0 AA PCI 32 bit Bus Master architecture LED Indicators Per Unit Power Green Red RJ45 Ports Per Port Link Activity Green Blinking Green Ring Port Amber Power Requirements Power Input Voltage PCI Power 5V DC on PCI bus External Power 9 30VDC in Terminal block ORing Industrial Networking Corp 30 ICS 4040 User s Manual Reverse Polarity Protection Operating Humidity 5 to 95 non condensing Dimensions W x D x H 124mm W x 100mm D Regulatory Approvals FCC Part 15 CISPER EN55022 class A EMS EN61000 4 2 ESD EN61000 4 3 RS EN61000 4 4 EFT EN61000 4 5 S2. Port 02 Disable M Port03 Disable Ea Port 04 Disa ble PCI Disable M System Warning Event Selection interface ORing Industrial Networking Corp 26 ICS 4040 User s Manual The following table describes the labels in this screen System Event Event to send notifications System Cold Start Alert when system restart Ring Topology Alert when Ring topology changes Change Port Event Disable Link Up Link Down Link Up amp Link Down Click Apply to activate the configurations 4 1 8 Front Panel The link status of ICS 4040 is shown here Click Close to close front panel on web Front Panel interface ORing Industrial Networking Corp 21 e orna ICS 4040 User s Manual 4 1 9 Save Configuration If any configuration changed Save Configuration should be clicked to save current configuration data to the permanent flash memory Otherwise the current configuration will be lost when power off or system reset Save Configuration Save System Configuration interface The following table describes the labels in this screen Save Save all configurations 4 1 10 Factory Default Factory Default Keep current IP address setting Keep current username amp password Factory Default interface This page is to reset switch to default configuration Click Reset to reset all configurations to the default value You can select Keep current IP address setting
3. Agent Setting Function SNMP Agent Setting Privilege Read Only o w Read and Write m Read Only v Read Only wl The following table describes the labels in this screen SNMP Agent SNMP Community should be set for SNMP Four sets of Setting Community String Privilege are supported Each Community String is maximum 32 characters Keep empty to remove this Community string 4 1 5 2 SNMP Trap Setting A trap manager is a management station that receives traps the system alerts generated by the switch If no trap manager is defined no traps will issue Create a trap manager by entering the IP address of the station and a community string To define management stations as trap manager and enter SNMP community strings and selects the SNMP version ORing Industrial Networking Corp 21 ICS 4040 User s Manual SNMP Trap Setting Trap Server Setting Server IP Community Trap Version vi O vac Trap Server Profile Server IP Community Trap Version none SNMP Trap Setting interface The following table describes the labels in this screen The server IP address to receive Trap Community Community for authentication Trap Version Trap Version supports V1 and V2c Add Add trap server profile Remove Remove trap server profile Show help file 4 1 6 VLAN A Virtual LAN VLAN is a logical network grouping that limits th
4. E MAIL or fault relay 4 1 7 1 Fault Alarm When any selected fault event is happened the Fault LED in switch panel will light up and the electric relay will signal at the same time ORing Industrial Networking Corp 23 ICS 4040 User s Manual Fault Alarm Power Failure PWR 1 PwR 2 Port Link Down Broken Port 01 Port 02 Port 03 Port 04 PCI Apply Fault Alarm interface The following table describes the labels in this screen Power Failure Mark the blank of PWR 1 or PWR 2 to monitor Port Link Mark the blank of port 1 to port 4 to monitor Down Broken Apply Click Apply to activate the configurations 4 1 7 2 System Alarm System alarm support to send warning notifications 1 SYSLOG 2 E MAIL You can monitor switch through selected system events System Warning SYSLOG Setting The SYSLOG is a protocol to transmit event notification messages across networks Please refer to RFC 3164 The BSD SYSLOG Protocol System Warning SYSLOG Setting SYSLOG Mode Bon Y SYSLOG Server IP Address 0 0 0 0 7 System Warning SYSLOG Setting interface ORing Industrial Networking Corp 24 ICS 4040 User s Manual The following table describes the labels in this screen SYSLOG Mode Disable disable SYSLOG Client Only log to local system Server Only log to a remote SYSLOG server Both log to both of local and remote server SYSLOG Server IP The remote SYSL
5. setting Apply Click Apply to set the configurations NOTE Follow the rule to configure the MAX Age Hello Time and Forward Delay Time 2 x Forward Delay Time value 1 gt Max Age value 2 2 x Hello Time value 1 RSTP Information Result of RSTP algorithm is shown at this table RSTP Information Root Bridge Information Bridge ID 0080001234567890 Root Priority 32768 Root Port Root Root Path Cost 0 Max Age Time 20 Hello Time 2 Forward Delay Time 15 Port Information Port Path Cost Port Priority OperP2P OperEdge STP Neighbor State Role Port 01 200000 128 True True False Disabled Disabled Port 02 200000 128 True True False Forwarding Designated Port 03 200000 128 True True False Disabled Disabled Port 04 200000 128 True True False Disabled Disabled PCI 200000 128 True True False Disabled Disabled RSTP Information interface 4 1 5 SNMP Configuration Simple Network Management Protocol SNMP is the protocol developed to manage nodes servers workstations routers switches and hubs etc on an IP network SNMP enables network administrators to manage network performance find and solve network problems and plan for network growth Network management systems learn of problems by receiving traps or change notices from network devices implementing SNMP ORing Industrial Networking Corp 20 m ICS 4040 User s Manual 4 1 5 1 SNMP Agent Setting You can set SNMP agent related information by
6. uif etos coto creto no out oc ome ota sil a ido 15 4 1 3 1 AS A etre e E eue satu e E a sudare iuke 15 4 1 3 2 POTESTAD a 16 414 REUNEN A A A NA 16 4 1 4 1 Past Recovery uoc H H 16 4 1 4 2 O DER PE EIES EE EE A ER EE A E EEEE TA E des 17 4 1 4 3 O 18 4 SNMP Cont UA a 20 E A A MA 21 4 1 5 2 SOMETA in 21 ALO VEAN tallado ius 22 4 1 6 1 VEAN Contieuration Fort baso anaconda 23 IS A A Lada TUE 23 4 1 7 1 Fault AUTE a a 23 4 1 7 2 SNS A T DT 24 AUG O 24 AM Saved ODH ordo aa a RO II sage oko unieo eacus oko ts dose o 28 NNI EI uo y De a eer 28 ALl System ReDOOLU eb ce 20 Technical Specifications asirios asa 30 e ICS 4040 User s Manual Getting to Know Your Switch Card 1 1 About the ICS 4040 The ICS 4040 is a cost effect and powerful industrial Ethernet switch card This card has many functions and it can operate under high temperature and dusty environment The ICS 4040 can be managed by WEB interface and a useful Window utility Open Vision Open Vision is powerful and useful network management software With its friendly user interface you can easily configure multiple switches at the same time and monitor the status of the switch cards 1 2 Software Features PCI Local Bus specification Rev 2 2 World s fastest Redundant Ethernet Ring O Ring Recovery time 10ms over 250 units connection Multiple Redundant Ethernet technology RSTP STP O Ring fast recovery mode supp
7. BOR Kernel Version v1 11 al Device MAC 00 1E 94 22 33 44 ed aa E t i Switch setting interface The following table describes the labels in this screen System Name Assign the name of switch The maximum length is 64 bytes System Description Display the description of switch System Location Assign the switch physical location The maximum length is 64 bytes System Contact Enter the name of contact person or organization Display the switch s firmware version Display the kernel software version MAC Address Display the unique hardware MAC address assigned by manufacturer default ORing Industrial Networking Corp 8 e m ICS 4040 User s Manual 4 1 2 2 Admin Password Change web management login username and password for secured management Admin Password User Name admin New Password rr Confirm Password sense Admin Password interface The following table describes the labels in this screen Username Key in the new username The default is admin Key in the new password The default is admin Confirm password Re type the new password Apply Click Apply to set the configurations 4 1 2 3 IP configuration You can configure the IP Settings manually or bet the IP address automatically in DHCP client mode in IP Configuration page IP Configuration IP Address 192168101 Subnet Mask 2582582850 BNSi IP Configuration interf
8. Industrial Lite Managed PCI Ethernet Switch Card ICS 4040 User s Manual Version 1 3 Feb 2010 il Orna e ORing Industrial Networking Corp 4F NO 3 Lane235 Baociao Rd Sindian City Taipei County 23145 Taiwan R O C Tel 886 2 2918 3036 Fax 886 2 2918 3084 Website www oring networking com E mail support oring networking com Table of Content Getting to Know Your Switch Card ecce creer sere 1 1 1 ADOUUTAS ICS ADA A A teeeesine ts 1 1 2 DOMWale Feat usais odia 1 1 3 Hardware Reales nod P 1 Hardware OVErVIO Wisin ielaoiia 2 2 1 A A 2 2 2 gisnsiz iukicsce m m 3 2 3 RO dosi sdb O a a cu Las eee 3 Cables RR 4 3 1 da pz ACS Hp cT 4 3 1 1 1I00BASE TX 10BASE T Pin Assignments esses nnne enne 4 WEB Management scrissi E aa T Rii 6 4 1 Configuration by Web BrowS r occcoooooncccnooonnnccononananoconnnnnnncconannnnnconnnnnnnccnnanannnccnnns 6 4 1 1 About Web based Management occcccccnnccncncnonononnonnnnnnnnnnnnnnnnnnonnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnos 6 T1 BILS AS acia ist 8 4 1 2 1 A A MS 8 4 1 2 2 Admin PAS Wallis 9 4 1 2 3 IP COMMIS UT ALON A eae m etatis uad rue u decla ERU Dee 9 4 1 2 4 SINTP COLS alTOH uti an 10 4 1 2 5 O Nes cues dM EMAIL a toS aoe 13 4 1 2 6 backups Restore 14 4 1 2 7 Uperade BItIWIT6 ena 15 T 53 SOU CONIC UT AIO s
9. OG Server IP address Address Apply Click Apply to activate the configurations Show help file System Warning SMTP Setting The SMTP is stand for Simple Mail Transfer Protocol t is a protocol for e mail transmission through the Internet Please refer to RFC 821 Simple Mail Transfer Protocol System Warning SMTP Setting E mail Alert Enable System Warning SMTP Setting interface ORing Industrial Networking Corp 25 ICS 4040 User s Manual The following table describes the labels in this screen E mail Alarm Enable Disable transmission system warning events by e mail Sender E mail The SMTP server IP address Address Mail Subject The Subject of the mail Authentication Username the authentication username Password the authentication password Confirm Password re enter the password Recipient E mail The recipient s E mail address t supports 6 recipients for a Address mail Apply Click Apply to activate the configurations System Warning Event Selection SYSLOG and SMTP are the two warning methods that supported by the system Check the corresponding box to enable system event warning method you wish to choose Please note that the checkbox can not be checked when SYSLOG or SMTP is disabled System Warning Event Selection system Event Event SYSLOG System Cold Start O Ring Topology Change Li Port Event Port No SYSLOG SMTP Port 01 Disable M
10. PDU Bridge Protocol Data Unit packet to check RSTP current status Enter a value between 1 through 10 Forwarding Delay The number of seconds a port to wait before changing from its Time 4 30 learning listening state to forwarding state Enter a value between 4 through 30 Path Cost The cost of the path to the other bridge from this transmitting 1 200000000 bridge at the specified port Enter a number 1 through 200000000 Priority 0 240 Decide which port should be blocked by setting the priority in LAN Enter a number 0 through 240 The value of priority must be the multiple of 16 Admin P2P Some of the rapid state transactions that are possible within RSTP are dependent upon whether the port concerned can only be connected to exactly one other bridge i e It is served by a point to point LAN segment or it can be connected to two or more bridges i e It is served by a shared medium LAN segment This function allows the P2P status of the link to be manipulated administratively True means P2P enabled False means P2P disabled Admin Edge The port directly connected to end stations and it cannot create bridging loop in the network To configure the port as an edge port set the port to True Admin Non STP The port includes the STP mathematic calculation STP BEEN algorithm is included for True setting STP algorithm is not ORing Industrial Networking Corp 19 ICS 4040 User s Manual o Tieuded for False
11. Ring Master and others will be Backup Masters 1 Ring Port The primary port when this switch is configured in O Ring p Ring Port The backup port when this switch is configured in O Ring Coupling Ring To enable Coupling Ring Coupling Ring can be used to divide a big ring into two smaller Rings to avoid effecting all switches when network topology change Itis a good application for connecting two Rings Coupling Port Set a port as coupling port to link to the Coupling Port of the switch in another ring Coupling Ring need four switch to construct an active and a backup link The coupled four ports of ORing Industrial Networking Corp 17 ICS 4040 User s Manual MI four switches will be operated at active backup mode Control Port Set a port as Control Port to link to the Control Port of the switch in the same ring Control Port used to transmit control signals Dual Homing To enable Dual Homing By selecting Dual Homing mode Ring will be connected to normal switches through two RSTP links i e backbone Switch The two links act as active backup mode and connect each Ring to the normal switches in RSTP mode Apply Click Apply to activate the configurations Note It is not recommended to set one switch as a Ring Master and a Coupling Ring at the same time due to heavy load of system 4 1 4 3 RSTP The Rapid Spanning Tree Protocol RSTP is an evolution of the Spanning Tree Protocol STP It p
12. ace ORing Industrial Networking Corp 9 ICS 4040 User s Manual The following table describes the labels in this screen To enable or disable the DHCP client function When DHCP client function is enabled the IP address of the switch will be assigned from the DHCP server of the network After clicking DHCP Client Apply button a popup message will show up to inform you when the DHCP client is enabling The current IP address will be lost and you should get the new IP address from the DHCP server The default setting is disabled To assign the IP address of this device If DHCP client option is enabled this item is not configurable The network DHCP IP Address server will assign the IP address for the switch and it will be displayed in this column The default IP is 192 168 10 1 To assign the subnet mask of the IP address If DHCP client function is enabled this item is not configurable The default subnet mask is 255 255 255 0 To assign the network gateway for the switch The default IP Gateway address of the gateway is 192 168 10 254 DNS To assign the primary DNS IP address DN2 To assign the secondary DNS IP address Apply Click Apply to set the configurations 4 1 2 4 SNTP Configuration The SNTP Simple Network Time Protocol settings help you to synchronize the time from the Internet SNTP Configuration SNTP Client EMS gt Daylight Saving Time Disable UTC Timezone GM T Gre B mwic
13. e broadcast domain which allows you to isolate the network traffic Only the members of the VLAN will receive traffic from the same members of VLAN Basically creating a VLAN from a switch is equivalent of reconnecting a group of network devices to another Layer 2 switch However all the network devices are still plugged into the same switch physically The ICS 4040 switch card supports port based VLAN only ORing Industrial Networking Corp 22 e m ICS 4040 User s Manual 4 1 6 1 VLAN Configuration Port Based Traffic is forwarded to the member ports of the same vlan group vlan port based startup set in the same group of the port can be a normal transmission packet without restricting the types of packets Port Based VLAN Port 01 Port 02 Port 03Port 04 Port 05 Port 06 Group i d a wi Group 2 al dl _ dl dl Group 3 E E E Group 4 a a VLAN Configuration Port Based VLAN interface The following table describes the labels in this screen Mark the blank to assign the port into VLAN group Apply Click Apply to activate the configurations 4 1 7 Warning Sending warning message is a very important function for the application of Ethernet switch You will be informed by SYSLOG and E MAIL by using ICS 4040 It helps you to monitor the status of the switch card on remote site When events occurred the warning message will send the message to your appointed server
14. h M e an Time D ubl in E di n bu rgh Li 8 bon i Lon don SNTP Server IP 409 4 amp B ane il Address 192 168 10 66 f Current System Time kalt Saving Pes ey Jan mE on v 2 sv ws Daylight Saving Offset E ln ours SNTP Configuration interface ORing Industrial Networking Corp 10 ICS 4040 User s Manual The following table describes the labels in this screen SNTP Client Enable or disable SNTP function to get the time from the SNTP server Daylight Saving Time Enable or disable daylight saving time function When daylight saving time is enabling you need to configure the daylight saving time period UTC Time zone Set the switch location time zone The following table lists the different location time zone for your reference AST Atlantic Standard 4 hours 8 am EDT Eastern Daylight EST Eastern Standard 5 hours am CDT Central Daylight CST Central Standard 6 hours 6 am MDT Mountain Daylight MST Mountain Standard hours 5 am PDT Pacific Daylight PST Pacific Standard 8 hours 4 am ADT Alaskan Daylight HAW HAW Hawaiian Standard HAW Hawaiian Standard A hours hours Nome Alaska 11 hours ORing Industrial Networking Corp 11 ICS 4040 User s Manual CET Central European FWT French Winter MET Middle European 1 hour 1 pm MEWT Middle European Winter SWT Swedish Winter EET Eastern European 2 hours 2 pm USSR Zo
15. iation w v Disable v Port Control interface The following table describes the labels in this screen Port NO O Port number for setting State Enable Disable the port Speed Duplex You can set Auto negotiation 100 full 100 half 10 full 10 half t e Flow Control Support symmetric and asymmetric mode to avoid packet loss c RN Apply Click Apply to activate the configurations ORing Industrial Networking Corp 15 Orang ICS 4040 User s Manual 4 1 3 2 Port Status The following information provides the current port status Port Status Port No Type Link State Speed Duplex Flow Control Port 01 100TX Down Enable N A N A Port 02 100TX UP Enable 100 Full Disable Port 03 100TX Down Enable N A N A Port 04 100TX Down Enable N A N A PCI 100TX Down Enable N A N A Port Status interface 4 1 4 Redundancy 4 1 4 1 Fast Recovery Mode The Fast Recovery Mode can be set to connect multiple Ethernet ports of ICS 4040 to one or more switches Fast Recovery Mode supports 4 priorities for redundant links only the qe priority port will be the activated port the other ports configured with lower priority will be the backup path Fast Recovery Mode v Active Port 1 Not included w Port 02 Notincluded Port 03 Notincluded w Port 04 Notincluded Not included Saale 1st Priority Apply nd Priority ard Priority amp th Priority Fast Recovery Mode interface The f
16. in Assignments 08 Niue ORing Industrial Networking Corp 4 m ICS 4040 User s Manual The ICS 4040 also supports auto MDI MDI X operation You can use a straight through cable to connect PC to switch The following table below shows the 10BASE T 100BASE TX MDI and MDI X port pin outs MDI MDI X pins assignment Pme moion vorxpon Reci Transm RD receive TD transmit Note and signs represent the polarity of the wires that make up each wire pair ORing Industrial Networking Corp ICS 4040 User s Manual WEB Management While making any establishment and upgrading firmware please remove physical loop connection first DO NOT power off equipment during firmware is upgrading 4 1 Configuration by Web Browser This section introduces the configuration by Web browser 4 1 1 About Web based Management An embedded HTML web site resides in flash memory on the CPU board It contains advanced management features and allows you to manage the switch from anywhere on the network through a standard web browser such as Microsoft Internet Explorer The Web Based Management function supports Internet Explorer 5 0 or later It is based on Java Applets with an aim to reduce network bandwidth consumption enhance access speed and present an easy viewing screen Note By default IE5 0 or later version does not allow Java Applets to open sockets You need to explicitly modify the bro
17. ne 1 BT Baghdad USSR Zone 3 hours 3 pm 2 WAST West Australian 7 hours 7pm Standard CCT China Coast USSR 8 hours 8 pm Zone JST Japan Standard 9 hours 9pm USSR Zone 8 EAST East Australian Standard GST Guam Standard USSR eevee pm Zone 9 IDLE International Date Line NZST New Zealand 12 hours Midnight Standard NZT New Zealand The following table describes the labels in this screen SNTP Sever IP Set the IP address of SNTP server Address Daylight Saving Set up the Daylight Saving beginning time and Daylight Saving ORing Industrial Networking Corp 12 ICS 4040 User s Manual Daylight Saving Offset Set up the offset time of Daylight saving Switch Timer Display the current time of switch Apply Click Apply to activate the configurations 4 1 2 5 LLDP LLDP Link Layer Discovery Protocol function allows the switch to advertise its information to other nodes on the network and store the information it discovers LLDP Configuration LLDP Protocol Dsante LLDP Interval 330 sec The following table describes the labels in this screen LLDP Protocol Enable or Disable LLDP function LLDP Interval The interval of resend LLDP by default at 30 seconds Apply Click Apply to activate the configurations Show help file ORing Industrial Networking Corp 13 e orna ICS 4040 User s Manual 4 1 2 6 Backup amp Restore You can save cur
18. ollowing table describes the labels in this screen Activate the fast recovery mode Port can be configured as 4 priorities Only the port with highest priority will be the active port iin Priority is the highest Click Apply to activate the configurations Note If you configure redundancy mode by DIP switch it is not allowed to change the operation mode by WEB Ul ORing Industrial Networking Corp 16 m ICS 4040 User s Manual 4 1 4 2 O Ring O Ring is one of the most powerful redundant ring technologies in the industry field With its advanced technology the recovery time of O Ring is less than 10 ms over 250 units It can minimize the interruption cause by network topology change There are three ring topology supported O Ring Coupling Ring and Dual Homing O Ring 7 O Ring Coupling Ring C Dual Homing RETF o Ly Feng Pont Card H Care D iia ls va T La Por E y p a viral Car n Card B a f Aa um la 5 9 x 7 1 gy y 9 E wn Card A Card C T Ring Master Disable Coupling Port Part 3 Homing Port PCI w ist Ring Port Port01 Control Port Port 4 w 2nd RingPort Port02 O Ring interface The following table describes the labels in this screen To enable O Ring Ring Master There should be one and only one Ring Master in a ring However if there are two or more switches which set Ring Master to enable the switch with the lowest MAC address will be the actual
19. orted to protect your industrial network Relay output for power failure Optional Easy to configure Web Windows utility for network management 1 3 Hardware Features ORing Industrial Networking Corp Redundant external DC power inputs PCI power and external DC 9 30V power on terminal block Operating Temperature 10 to 60 C Storage Temperature 40 to 85 C Operating Humidity 596 to 9596 non condensing 4 10 100Base T X Ethernet ports ICS 4040 User s Manual Hardware Overview 2 1 Front Panel The following table describes the labels on the front panel of ICS 4040 Port Description 10 100 RJ 45 fast 4 10 100Base T X RJ 45 fast Ethernet ports support Ethernet ports auto negotiation Default Setting Speed auto Duplex auto Flow control disable Push reset button 3 seconds to reset the configuration of switch Push reset button 5 second to reset the switch into Factory Default ICS 4040 front panel 1 Reset button Push the button 3 seconds to restore the configuration 5 seconds for factory default 2 LED for Fault Relay When the fault occurs the amber LED will be light on LED for Power When the PCI power on the green led will be light on When PCI O power off and External Power on the red led will be light on External power input with DC 9 30V LED for Ethernet ports link act status LED for Ring ports indication 10 100Base T X Ethernet ports N o o0 ORing Indust
20. rent configuration from the switch to TFTP server or restore the configuration from TFTP server in this page Backup amp Restore Restore Configuration Backup Configuration TFTP Server IP Address 192 168 10 66 PEINE acta vir Backup amp Restore interface The following table describes the labels in this screen TFTP Server IP Fill in the TFTP server IP Address Restore File Name Fill in the file name Click restore to restore the configurations Click restore to restore the configurations Click backup to backup the configurations ORing Industrial Networking Corp 14 m ICS 4040 User s Manual 4 1 2 7 Upgrade Firmware Upgrade Firmware page allows you to update firmware of the switch Before updating make sure you have had your TFTP server ready and the firmware image i e image bin is on the TFTP server Upgrade Firmware TATP Server IP 192 168 10 66 Firmware File Name image bin Upgrade Hel Update Firmware interface 4 1 3 Port Configuration 4 1 3 1 Port Control By this function you can set the state speed duplex and flow control Port Control Port 01 Enable v AutoNegotiation w Disable v Port 02 Enable Enable AutoNegotiation w Disable wj v Port 03 Enable AutoNegotiation v Disable v v Port 04 Enable v Enable AutoNegotiation w w Disa Disable B wi PEI Enable w AutoNegot
21. rial Networking Corp 2 ICS 4040 User s Manual 2 2 BET Panel LEDs Green Power of PCI interface or Tr 3 Amber Fault indicator Power P me m failure or Port down fail M eo o mm Ring mode indicate Ring port Fast Recovery indicate Act port 2 3 DIP Switch The operating mode of ICS 4040 can be configured by DIP switch The setting of the DIP switch is shown as table below e DIP SW Number DIP CUE 1 DIP o 2 Redundant Mode E recovery mode RSTP E SN e Note When ICS 4040 operated in Redundancy mode by DIP SW The default setting is shown as below 1 The O Ring mode will set P1 to be the 1 Ring port and P2 to be the 2 ring port 2 The Redundant mode will set P1 P4 to the 1 4 priorities ORing Industrial Networking Corp 3 on ICS 4040 User s Manual Cables 3 1 Ethernet Cables The ICS 4040 has standard 100BASE TX 10BASE T Ethernet ports According to the link type the switch use CAT 3 4 5 5e UTP cables to connect to any other network device PCs servers switches routers or hubs Please refer to the following table for cable specifications Cable Types and Specifications 10BASE T Cat 3 4 5 100 ohm UTP 100 m 328 ft RJ 45 100BASE TX Cat 5 100 ohm UTP UTP 100 m 328 ft RJ 45 3 1 1 100BASE TXAOBASE T Pin Assignments With 100BASE TX 10BASE T cable pins 1 and 2 are used for transmitting data and pins 3 and 6 are used for receiving data RJ 45 P
22. rovides faster convergence of spanning tree after a topology change The system also supports STP and the system will detect the connected device that is running STP or RSTP protocol automatically RSTP setting You can enable disable RSTP function and set parameters for each port RSTP Setting RSTP Mode Enable Bridge Configuration Hello Time 1 10 2 Forward Delay Time 4 30 15 Port Configuration neno lo a ld aero Port y 200000000 0 240 4minP2P Admin Edge Admin Non STP 20 200000 128 auto e Tue wj Fase Ml PN 200000 28 ato Tue False m 28 Auto True v False RSTP Setting interface ORing Industrial Networking Corp 18 m ICS 4040 User s Manual The following table describes the labels in this screen RSTP mode You must enable or disable RSTP function before configuring the related parameters Priority 0 61440 A value used to identify the root bridge The bridge with the lowest value with the highest priority and is selected as the root If the value changes you must restart the switch The value must be multiple of 4096 according to the rule of the protocol Max Age 6 40 The number of seconds for a bridge to wait without receiving opanning tree Protocol configuration messages before reconfiguration Enter a value between 6 through 40 Hello Time 1 10 The time that controls switch sends out the B
23. urge EN61000 4 6 CS ORing Industrial Networking Corp 31
24. wser setting in order to enable Java Applets to use network ports Preparing for Web Management The default setting is as below IP Address 192 168 10 1 Subnet Mask 255 255 255 0 Default Gateway 192 168 10 254 User Name admin Password admin System Login 1 Launch the Internet Explorer 2 Type http and the IP address of the switch Press Enter ORing Industrial Networking Corp 6 ICS 4040 User s Manual File Edit View Favorites Tools Help a Back 7 gt x E A ya Search yr Favorites e A7 a n Address http 192 168 10 1 Eoo Links gt ne The login screen appears Key in the username and password The default username and password is admin 5 Click OK button then the main interface of the Web based management appears Connect En 192 158 10 1 index htm User name f mn v Password esas Bi Remember my password Login screen Main Interface Close a System Name ICS 4040 seria Industrial 4 port Lite managed PCI Ethernet Cines TUE Switch Card with 4x 10 100TX BH Syste OID 1 3 6 1 4 1 25972 100 0 1 14 E Kernel Version v1 11 Main interface ORing Industrial Networking Corp 7 ICS 4040 User s Manual 4 1 2 Basic Setting 4 1 2 1 Switch setting System Location i i E EH BB a System Contact ES System OID 1 3 6 1 4 1 25972 100 0 1 14 LEO L Po Firmware Version v1 00
Download Pdf Manuals
Related Search