Home
Manual - Marshall Electronics
Contents
1. 7 2 2 Use RS 422 Connection 1 Hold the two sides of RS 422 connector and pull out in the direction shown by the arrow in the figure below 2 Peel off a section of copper wire AWG Nos 28 to18 and insert it into Miarshall Electronics 33 3 Insert the wired RS 422 connector back to the camera Now the connection is completed When RS 422 connection is being used do not use RS 232C connection Miarshall Electronics 34 Troubleshooting This chapter describes problems you may encounter while using CV620 If you have questions please refer to related chapters and follow all the suggested solutions If the problem still occurred please contact your distributor or the service center No Problems Boot without 1 SE sure you have plugged in the power cord power signal 2 Make sure the Service DIP switch is Off 1 Check the power No image output 2 Check if DIP switch is properly set Refer to from the CV620 Chapter 7 DIP Switch Setting for related settings 3 Make sure the display supports the output resolution in general the resolution is 1080p60 1080i60 720p60 4 Replace the cables and make sure they are not faulty CV620 image is Please use 1080i 1080p or 720p at severely delayed 60 59 94 50fps rather than 30 29 97 25fps Not working after After completing DIP Switch setting unplug and reconnect the power cord and turn on the machine to changes to DIP change the setting
2. Switch setting 1 Please confirm if the Camera Select on the remote CV620 cannot be control can be used together with the IR Select on CV620 Please prevent CV620 from direct sunshine Make sure the energy saving bulb and the IR touch screen are as far as possible in order to avoid interference When several CV620s are connected in the same area the operation of two remote controls at the same time may result in signal interference It is recommended to use one remote control only Please consult the distributor to make sure the The device cannot firmware version is the latest one The steps to be controlled with check version is as follows 1 1 Press MENU on the remote control 1 2 Select Status 1 3 Go to Page 5 of System 1 4 Make sure the firmware version is correct operated by remote control Miarshall Electronics 35 Make sure the connection is correct RS 232 422 Input Make sure System Switch DIP1 and DIPS are correct The device cannot 1 Make sure the connection is correct RS 232 422 be controlled with Input RS 232 RS422 Make sure System Switch DIP1 and DIP3 are correct Miarshall Electronics 1910 E Maple Avenue El Segundo CA 90245 Phone 310 333 0606 800 800 6608 Fax 310 333 0688 http www lcdracks com Miarshall Electronics 36
3. 6 7 2 Manual focus 1 Press MF on the remote control to turn on the manual focus function 2 Press Focus or Focus to adjust 6 8 would like to adjust the focus speed 6 8 1 Adjust the AF sensitivity AF triggering speed The higher the speed is the faster AF is triggered To shoot fast moving objects AF can be set to High or Middle which is applicable to quick focus When the environment is too dark to enable auto focus or fixed objects have to be shot in different brightness AF can be set to Low h Press MENU to activate the setting menu 2 Press gt or lt 4 to select Auto Focus 3 Press ENTER to activate 4 Press A or v to select AF Sensitivity 5 Press ENTER to activate 6 Press gt or lt 4 to select High Meddle Low 7 Press MENU to exit 6 8 2 Adjust the focus speed The focus speed upon triggering AF Normal default Image flickering may not occur Fast The focus speed is fast but image flickering is more likely to occur Miarshall Electronics 29 1 Press MENU to activate the setting menu Press gt or 4 to select Auto Focus Press ENTER to activate Press A or v to select AF Speed Press ENTER to activate Press or lt 4 to select Normal Fast Press MENU to exit NO O KR O PD 6 9 would like to set the image mode 1 Press Picture on the remote control to switch Off Neg B amp W 6 10 I wou
4. 4 1 Preparation before installation Installation and connection of CV620 Camera requires special skills To install by yourself please follow necessary steps ensure steady and tight installation of the device and pay attention to your safety to avoid any accident 4 1 1 Ensure the safety of the installation environment Please do not install the device on unstable ceiling or in a place where the device is in danger of falling to avoid any accident 4 1 2 Please check whether accessories in the box are complete or not Please contact the supplier for any shortage and make sure to keep the accessories in the box intact 4 1 3 Please choose a proper place for installation of CV620 in advance Please determine an installation place according to the following requirements 4 1 3 1 Confirm the position for the object to be captured 4 1 3 2 Confirm whether the CV620 is set at a proper distance from other light sources 4 2 Instruction for installation 4 2 1 would like to install CV620 on the desk 4 2 1 1 Precautions for installation Please install the machine on a flat desk Do not grab the camera head by hand when handling the device Do not rotate the camera head by hand Improper rotation may result in breakdown of the camera re ae xi ar rr iJ i i j fl NA r TF o E i ite k i Fal j i i ol i h ii T ha JAN A AN r XK p gt qe y a f P Q Aae YA
5. 25 Manual Speed oo ee Manually set the shutter mode mode a cn nee o 11600 ife 17800 iat SO nen Marshall Electronics 22 1 4 1 3 1 2 1 2 1 1 YA Marshall Electronics i Ne Manually set the IRIS 23 ls White Balance One Push Trigger IMarshall Electronics a NG ENTER The maximum electric gain limit Set WDR Auto Indoor Outdoor One Push WB ATW Manual Outdoor Auto Sodium Lamp Auto Sodium Lamp Select the color temperature mode Sodium Lamp Outdoor Auto One push trigger Adjustable when the white balance mode is set to Manual 24 Adjustable when the white 0 C 255 balance mode is set to Manual Picture effect Set the picture effect oe the image O Set 2D noise reduction NO OF AIO N Set 3D dynamic noise reduction i 2 3 4 5 6 7 8 1 2 3 4 o 6 A Adjustable when Image O A 14 Mode is set to Custom Adjustable when Image O A 14 Mode is set to Custom 1 ff A O Adjustable when Image 2 Standard Mode is set to Custom Mode is set to Custom Adjust the contrast of the Contrast Fn Adjustable when Image Mode is set to Custom Adjust the shadow detail and transparency of the Black Level screen Adjustable when Image Mode is set to Custom Miarshall Electronics 25 N N N Pan Left Limit 170 0 Limit the left angle Tilt UP Limit Limit the upward angle mm GWR Limit the downward angle L
6. Precautions for installation 1 Before installation please confirm the orientation of the machine relative to the object to be captured It is recommended that the machine should be set at a distance of more than 1 meter away from the object to be captured Please adjust for a best distance according to the magnification of the lens The machine including metal plates is weighed at about 2 5 kg If it is to be installed on the ceiling please use the hanger that has obtained UL security approval to prevent the machine from falling down Please check whether the camera is installed securely on a regular basis 4 2 2 6 Installation steps 1 Please adjust resolution on DIP switch at first Please refer to Chapter 7 DIP Switch Setting for the relevant descriptions on DIP switch 2 Fix the metal plate A on the machine base with 4 M3 screws IMarshall Electronics 13 3 Lock the metal plate B on ceiling mounted hanger Caution 1 Please use the hanger that has obtained UL security approval 2 Please reserve the hole for the connecting wires of the camera 4 Combine the metal plate A and the metal plate B 1 Push the metal plate A up to the ceiling and then to the right to latch the metal plate B 2 Fix with 3 M3 screws Miarshall Electronics 14 4 2 2 7 How to remove 1 Remove the connecting wires from the camera 2 Uninstall the camera together with the ceiling loosen the three screws that fi
7. battery type in the remote control may result in breakdown Follow local instructions on how to dispose of used batteries Miarshall Electronics 3 E Precautions Warning To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture If Camera will not be used for an extended time unplug it from the power socket Risk of Electric Shock DO NOT OPEN Caution To reduce the risk of electric shock do not remove cover or back No user serviceable parts inside Refer servicing to licensed service personnel This symbol indicates that This symbol indicates that this eguipment may contain there are important operating dangerous voltage which and maintenance could cause electric shock instructions in this User Manual with this unit m FCC Warning This Camera has been tested and found to comply with the limits for a Class A digital device pursuant to Article 15 J of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a commercial installation This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference causing equipment standard entitled Digital Apparatus ICES 003 of Industry Canada Cet appareil numerique respecte les limites de bruits radioelectrigues applicables aux appareils numeriques de Classe A prescrites dans la norme sur le material brouilleur Appareils Nume
8. i j e J y A i Miarshall Electronics 7 4 2 1 2 Installation steps 1 Please adjust DIP switch at first prior to installation Please refer to Chapter 7 DIP Switch Setting for the relevant descriptions on DIP switch 2 Place the camera on a flat desk directly to ensure the normal vertical and horizontal operation of the machine 4 2 2 would like to install CV620 on the ceiling 4 2 2 1 Prepare for the parts and equipment required during the installation 1 Accessories of CV620 in the box metal plates A B and M3 screw x 7 2 Screw for locking on ceiling mounted hanger x 4 3 Drilling machine screw driver ladder 4 2 2 2 Dimension Length x Width x Height 174x186 13x185 88 Weight 2 0Kg 185 88mm 186 13mm IMarshall Electronics 4 2 2 3 Max rotation dimension of camera 200 4mm Miarshall Electronics 4 2 2 4 Size Diagram 1 Metal plate B ceiling side M4 Metal plate B locking screw Metal plate B locking bolt 8 z gt F wre GC 40 00 M3 threaded M3 threaded hole hole Er oD ope a a Metal plate B ceiling side Marshall Electronics 10 117 00 2 Metal plate A machine side Metal plate A locking screw i i MA 00 Metal plate A machine side m Marshall Electronics 11 112 0 mm 3 Bottom of machine 110 0 mm 55 0 mm M MN ME SS eo o Miarshall Electronics 12 4 2 2 5
9. 1 3 is selected with IR SELECT 6 2 would like to save the current lens position data 1 Hold Preset ID on the remote control to save the current position data ID shall be a digit 0 9 Use VISCA Command to save the position data to 0 127 6 3 would like to clear the saved position data 1 Hold Reset ID on the remote control to clear the given position data ID shall be a digit 0 9 Use VISCA Command to clear the position data of 0 127 6 4 would like to turn on the back light compensation function 1 Press Back Light on the remote control to turn on or turn off the back light compensation 6 5 would like to adjust the shooting angle of the lens 1 Press Tilt 4 or Tilt v on the remote control to adjust the angle upward or downward 2 Press Pan or Pan on the remote control to adjust the angle to right or left 3 Press Pan Tilt Reset on the remote control to reset the angle to the center point 6 6 would like to zoom in out images 6 6 1 Adjust image size 1 Press Fast on the remote control to zoom in images 2 Press Fast on the remote control to zoom out images Miarshall Electronics 28 6 6 2 Fine tune image size 1 Press Slow on the remote control to zoom in images 2 Press Slow on the remote control to zoom out images 6 7 would like to adjust the focal length 6 7 1 Auto tune 1 Press AF on the remote control to adjust automatically
10. Marshall Electronics CV620 WH amp CV620 BK Full HD Broadcast PTZ Camera Installation Guide Marsha T To download the latest version of Quick Start Guide software or driver etc please visit www lcdracks com Table of Contents Safety InSUucuohSs ui lee ioc ah alae TR NGLANNAU GG Na OR sacs 3 PRC CAUTIONS ii AE YH HR RR HAFAN 4 GG WAM mn NR RR CN EN a 4 EN55022 CE Radiation Warning Au cs oa Dw O OG daw 4 Package ConteniS IAA 5 Product OVervie W uid al yeu Wa nol WOW YN a EE 6 Gel OVerMIGW uc aces df Y Y Ff NN 6 3 2 DescHDoTlion OF LED ITdICatOl AA 6 Instruction TOF INSTAIAUION iei iei Oia O GO O FI O GO DE O a 7 4 1 Preparation before installation cccccccssssseeeceesseceeeeeeeseeeeseeeseeeess 7 4 2 lnstruction Tor InstallBtiOn zs ue GR UU Uw Ge CUD Dw LO DR 7 4 3 Connecting the aaa akaka kabaka akawa 16 Remote Control and Setting Menu ccccssssseeeeeeeseeceensnneeeeeeeeeenneeeeees 19 5 1 Functions of remote COntrOl cccccceccceeeeeceeceeeeeeeseeeesaeeesseeeeseaees 19 G2 GENI MEN a ko cee eee Ai i ee ee 20 Descriptions of Major FUNCTIONS ccseceeesessseeeseeessseeseensseeeseoeenseeseees 28 61 FWomldIKe to SWIICD lO Ha Sa eC Fin 29 6 2 would like to save the current lens position data 28 6 3 would like to clear the saved position data 28 6 4 would like to turn on the
11. back light compensation function 28 6 5 would like to adjust the shooting angle of the lens 28 6 6 would like to zoom in out IMAGES ceeeeeeeeeeeeeeeeeeeeeeeaeeeeeeeeaeees 29 6 7 would like to adjust the focal length www mmmmmmmaaw 29 6 8 would like to adjust the focus speed www wwmmmmmmwamwmwnmaminza 29 Miarshall Electronics 1 6 9 would like to set the image mode wwwmmamwnanwwnanamanamwnza 30 6 10 would like to freeze IMAGES ccseccccseeeeeeseeseeeeeeeeeeeaeeeeeeseeeeeesaaes 30 6 11 would like to rotate the IMAGE cccceeeececseeeeeeeeeeeeeeaeeeeeeaeeeeeneaes 30 6 12 would like to change the camera direction 30 6 13 would like to display the current Status w wwmmmnamwmnwa 30 DIP SWitch Setting wi kakuwa kauka ushawishi kuhusika 31 TAY DIP SVT CIM SU E 31 Tee R9422 CONNEC wie O 33 TROUDICSIMOOUING i iedydd Creu Onid EOS 35 IMarshall Electronics 2 Safety Instructions Always follow these safety instructions when setting up and using the Camera 1 Use attachments only as recommended 2 Use the type of power source indicated on the Camera If you are not sure of the type of power available consult your distributor or local electricity company for advice 3 Always take the following precautions when hand
12. ear the Pan Tilt setting Reset Uo ln yn Auto Far Near Manual D E Picture Switch image effect Off Neg o o see Power Power switch Direction Set Preset Appoint an ID 0 9 to save the current position data Reset Appoint an ID 0 9 to delete the Marshali current position data Zoom Fast Adjust image size Zoom Slow Fine tune image size Miarshall Electronics 19 5 2 Setting menu Press Menu on the remote control to enter the setting menu the bold underlined values in the following table are defaults 2 Level 3 Level Function Minor Items Adjustment Descriptions Values Full Auto Bright Shutter Pri Exposure mode setting Iris Pri Manual Comp Exposure The value can be adjusted Comp bevel 7 0 7 only after Exposure_ Comp is activated Spottt Jonot The value can be adjusted Spot Light On Off when the mode is set to Full Auto or Shutter Pri Spot Light The value can be adjusted 3 ig X 0 15 Y 0 15 only after Spot Light is osition activated 60 30 50 25 SAUNE Feika Shutter priority setting Priority mode mode 1 10000 1 10000 1 6000 1 5000 1 4000 1 3500 1 3000 1 2500 1 2000 1 1750 1 1500 1 1250 1 1000 1 1000 1 725 1 600 1 500 1 425 1 350 1 300 Miarshall Electronics 20 1 125 1 120 1 100 1 100 1 25 112 1 6 Iris Priority IRIS priority setting IMarshall Electronics 21 cs OP OV eG Manually set the gain 60 30 50
13. imit 150 deg sec Set the rotation speed of Preset Speed 2 250 deg sec the cradle head when 350 deg sec Preset is executed Off Mirror Set the mode at which the Flip image is turned Mirror Flip Pan Tilt Limit ON Off Turn on off the angle limit setting Pan Right 7 o 0 170 Limit the right angle Pan Tilt Zoom Select the AF triggering ch l speed The higher the AF Sensitivity speed is the faster AF is triggered Focus speed upon AF speed triggering AF 6 NTSC LB NTSC CP NTSC SQ C Video PAL LB Image mode PAL SQ Video Type Select output video type Turn on off the prompt Prompt Non information on the display i Turn on off the infrared aeoe owon English Chinese Marshall Electronics 26 Device Controller Protocol PD Protocol PD PELCO D The Protocol set to PD PD Address 1 255 allows the camera ID E address to be assigned OoOnNDOORWND 1920x1080 60p 1920x1080 50p 1920x1080 30p 1920x1080 25p 1920x1080 60i 1920x1080 50i 1280x720 60p Output Mode 1280x720 50p 1280x720 30p 1280x720 25p 1080 59 94p 1080 59 94i 1080 29 97p 14 720 59 94p 15 720 29 97p Reset all configurations to Factory Reset ON Off factory default settings Display the current setting status Miarshall Electronics 27 Descriptions of Major Functions 6 1 would like to switch to CV620 1 Press Camera 1 3 on the remote control to select CV620 eo Camera
14. ld like to freeze images 1 Press Freeze on the remote control to freeze the current image on the display 6 11 I would like to rotate the image 1 Press Mirror on the remote control to switch Off Mirror Flip Mirror Flip 6 12 would like to change the camera direction 1 Press L R Direction Set on the remote control to switch L R Direction Off Normal 6 13 would like to display the current status 1 Press Info on the remote control to display the current status information Miarshall Electronics 30 DIP Switch Setting lt Note gt Please turn off the machine before changing DIP switch setting 7 1 DIP SWITCH 7 1 1 OUTPUT Switch Output Mode Settin Output Mode 1920x1080 60p we 1920x1080 50p E 0 0 Ll 1920x1080 30p 1920x1080 25p E E z 1920x1080 60i 1920x1080 50i aat BAA Ea IMarshall Electronics 31 7 1 2 IR SELECT Descriptions 7 1 4 System Switch Setting Function Descriptions DIP 4 RS 232C RS 422 selector OFF RS 232C ON RS 422 OFF Off ON On OFF 9600 ON 38400 DIP 4 Reserved Miarshall Electronics 32 7 2 RS 422 Connection 7 2 1 RS 422 Pin Description RS 422 LITTTTTTT 123456789 I PinNO Function AA AU AA BXDOUT AA ao AA aw AA GN GND PRXDIN S O NA NA NA lt Note gt For SONY products please connect IN to OUT For non SONY products it may be necessary to connect IN to OUT
15. ling the plug Failure to do SO may result in sparks or fire m Ensure the plug is free of dust before inserting it into a socket m Ensure that the plug is inserted into the socket securely 4 Do not overload wall sockets extensions leads or multi way plug boards as this may cause fire or electric shock 5 Do not place the Camera where the cord can be stepped on as this may result in fraying or damage to the lead or the plug 6 Do not block the slots and openings in the case of Camera They provide ventilation and prevent the Camera from overheating Do not place the Camera on the soft surface of sofas carpets or others 7 Never push objects of any kind through cabinet slots Never allow liquid of any kind to spill into the Camera 8 Except as specifically instructed in this User Manual do not attempt to operate this product by yourself Opening or removing covers may expose you to dangerous voltages and other hazards Refer all servicing to licensed service personnel 9 Unplug the Camera during thunderstorms or if it is not going to be used for an extended period Do not place the Camera or remote control on top of vibrating equipment or heated objects such as a car etc 10 Unplug the Camera from the wall outlet and refer servicing to licensed service personnel when the following situations happen m If the power cable or plug becomes damaged or frayed m lf the camera is wet with liquid rain or water Note Using an incorrect
16. riques NMB 003 edictee par l Industrie m EN55022 CE Radiation Warning This product is intended for use in a commercial industrial or educational environment It is not intended for residential use This is a Class A product In a residential environment it may cause radio interference in which case the user may be required to take adequate measures The typical use is in a conference room reception room or hall IMarshall Electronics 4 Package Contents CV620 Power Cord Appearance may vary depending on country region Metal Plate A Instruction for installation Remote Control Power Adapter RS 422 Connector Metal Plate B M3 Screws i fg ji Ke i f YE ji AW e i j y A j j ii e _ J j j Marshall Electronics Product Overview 3 1 Overview 0000 2 o 3 Standby LED indicator 4 DVI output 5 Component output 6 Power input 7 IR SELECT 8 OUTPUT Switch 9 Camera Address Selectors 10 RS 232 output 11 RS 232 input 12 RS 422 connection 13 VIDEO output 14 3G SDI output 3 2 Description of LED indicator 3 2 1 Power 3 2 1 1 No light Power off 3 2 1 2 Green light In use 3 2 1 3 Flickering green Signal from the remote control is received the indicator flickers every 0 5 second 3 2 2 Standby 3 2 2 1 Orange In standby mode 3 2 2 2 No light Power on Miarshall Electronics 6 Instruction for installation
17. x the metal plates A and B and push to the left to remove the machine 3 Then remove the screws on the hanger and the machine Miarshall Electronics 15 4 3 Connecting the device 4 3 1 Image output 4 3 1 1 Connecting to a HDTV computer monitor DVI Monitor Or HDTV Miarshall Electronics 16 4 3 1 3 Connecting to a HDTV 3G SDI SDI Cable oo oc O O ouput ESA e222 Rs 232 OUT maai Miarshall Electronics 17 4 3 2 Controlling VCs with the computer 4 3 2 1 Connecting to one computer for connection between CVs RS 232 in out With RS 232 in out at most 7 CVs can be connected 4 3 2 2 Connecting several CV620s to one computer via RS 422 232 Please refer to 7 2 RS 422 connection for the RS 422 connection instructions With RS 422 at most 7 CVs can be connected Miarshall Electronics 18 Remote Control and Setting Menu 5 1 Functions of remote control The below functions are listed alphabetically item Description lt gt A V Move the lens Back Light Turn on off back light compensation Camera Select 1 3 CV620 select Focus Turn on manual focus to adjust the Manual focal length Far Near Freeze Freeze the screen Home Enter Go back to the main page Execute Info Status information Pan yan rit L R L R Direction Off Normal Direction Set Menu Display OSD menu Mirror Rotate the image Off Mirror Flip Mirror Flip Pan Tilt Cl
Download Pdf Manuals
Related Search
Related Contents
アルバムを保存する ソフトをインストールする 付属のCD-ROM ROBOT魂 SIDE MS バイアラン・カスタム 取扱説明書 268.8 KB V7 ULTRA-THIN HDMI® CABLE WITH ETHERNET 2m Samsung HM7000 User Manual ficha-tecnica-ambulancias-tab Manual del usuario (Versión: 5.0.0) - Artisan Technology Group is your source for quality new and Manual máquina de costura MC695 Vzug Combair SEP Copyright © All rights reserved.
Failed to retrieve file