Home

GsmAlarm-500 (V1.04)

1. Address 133 Parameter System parameter G Manufacturer programmed value 01 5 7 15 PARAMETER H DATA TRANSFER TO THE ALARM MONITORING STATION This parameter is used for setting mode of data transfer to the alarm monitoring station This parameter is described in Chapter 7 3 in more detail Address 233 Parameter System parameter H Manufacturer programmed value 00 5 7 16 PARAMETER J SYSTEM RESPONSE TO INTENTIONAL GSM JAMMING Parameter J defines the system response to intentional GSM jamming Explanation of operation 238 00 O GSM Jamming detection is off 233 oo An SMS message is sent to users after resuming of communication 01 238 02 Detection of GSM Jamming signal activates the siren 238 03 Operates as the functions 01 and 02 Manufacturer programmed value 01 GsmAlarm 500 Software ver 1 04 31 PROGRAMMING 5 7 17 PARAMETER L SMS STRUCTURE AND SMS PASSWORD FUNCTIONALITY This parameter is described in Chapter 5 3 2 5 in more detail Adresas Parametras System parameter L Manufacturer programmed value 32 5 7 18 PARAMETER P PARTITIONING Explanation 236 00 Partitions do not exist System is divided into two partitions Manufacturer programmed value 00 5 7 19 ACCESS CODE LENGTH 4 OR 6 DIGITS Explanation 2344 Four digit user access code 234 G Six digit user access code Manufacture
2. F System Response to Incoming Calls and Number of Calls in Alarm Stalen en ni a a a envied 31 5 7 14 Parameter G Delay Time of Report SMS about the Power Supply Failure 31 5 7 15 Parameter H Data Transfer to the Alarm Monitoring Station cccccceeceeseeeeeneees 31 5 7 16 Parameter J System Response to Intentional GSM Jamming 0 0 0 cc ceeeseeseeseeeeeeeees 31 5 7 17 Parameter L SMS structure and SMS Password Functionality cccecceeseereeseees 32 5 7 18 Parameter P Partitioning ccecececcesscessessecescesseeesecesecsseeeseceseceeeseeceescseeeeeeeeeeeeeseess 32 5 7 19 Access Code Length 4 or 6 Digits 0 0 cccccccscccscsseeesseeseesseesseceseenseesseseeceeeeeseeeseeeseens 32 5 7 20 Exit Delay Audible Indication cccccccceccsescesscesseeseceseceseeeseceseceseeeaeceeecneeeeeeseeeeseeeneens 32 5 7 21 Assigning Keypad Z Ones s sscveco sucessenssdhacsecesss cnedadi E E E os 32 5 7 22 Setting System CLOCK ici cesse sccbevccacedel echve tei onesies irei an i E EEEE E REER 33 5 7 23 Programming 24 Hour Timer 5 vccecasanascisonextiaendicepencipatcmeniaraaensses iearaeeanensieNaen vaniuatoaacens 33 5 7 24 Programming CONTACT ID User Account NUMDBGD co sescssssosssecsssasvousesessanoresisonsvaanionas 34 5 7 25 Temperature Ris CUI secesii nar aenea arr NEE EIEEE ESA N Eee TR ERES 34 5 8 Programming iButton Keys 0 0 c cc ccceccessecssceseseeeeeeceseeceeecsee
3. 8 1 3 MEM KEY ALARM MEMORY DISPLAY If an alarm has occurred on a zone the respective zone LED will flash the MEM key will light up and the zones will be stored in memory Memory indication mode is activated by pressing MEM key MEM starts to flash Alight keys indicate which zone had been triggered Memory is erased automatically when armed mode is activated or by pressing CLEAR key when memory indication mode is active If K32LCD KEYPAD is used after pressing MEM and further BYP it can be seen what were the last alarm events It is shown in the LCD display when and what zone was activated 128 last events are stored in the memory of system GsmAlarm 500 Software ver 1 04 40 SYSTEM CONTROL 8 1 4 BYP KEY BYPASS PROGRAMMING A bypassed zone will not cause an alarm If a zone is bypassed the panel may be armed Ready light will be on even if the zone is open Use zone bypassing when access is needed to part of the protected area Also damaged wiring or contacts on a zone may be temporarily bypassed until repairs can be made so that the panel can be armed To bypass zones press BYP key and enter 4 or 6 digit user access code BYP key starts to flash Zone can be bypassed by pressing key indicating certain zone number Constantly alight key indicates of certain zone as bypassed To activate zone press key indicating certain zone number one more time Press CLEAR key to turn off BYPASS programming mo
4. A load resistor of 4 7k also should be used A triggered fire sensor is switched off with an SMS message or a DTMF keypad command for C3 output see Ch 14 GsmAlarm 500 Software ver 1 04 10 INSTALLATION 4 3 CONNECTION OF TEMPERATURE SENSORS GsmAlarm 500 has temperature measurement possibility Up to 6 temperature sensors KTY81 110 PHILIPS can be connected to the GsmAlarm 500 2 pin terminal block GsmAlarm 220 Input Temperature sensor Fixing hole KTY81 110 PHILIPS In order to minimise influence of external interferences and measurement error it is recommended to use shielded twisted pair cable 0 5 mm Shield is connected to ground wire only in one end close to GsmAlarm 500 board Use 2 pins terminal block with a fixing hole for temperature sensor fastening Parameter A must be changed in order to activate temperature measurement mode see Ch 5 3 1 1 Input parameter T defines alarm temperature Alarm temperature can be programmed in 0 99 C rage T00 T99 In temperature measurement mode input operates the same as in protection mode i e all operating modes are valid with two exceptions a No entry delay in 440 A50 system generates alarm instantly after temperature reaches programmed value b No prohibition for arming i e user can activate armed mode although temperature measurement zone has been triggered Recommended values of parameter M M40 or MOO In first case if the s
5. 5 7 15 Possible values are presented in the table Information that is received by users Hxy_ Information that is received by alarm ALRNRI1 ALRNRS xI y monitoring station Users doesn t get information about 0 0 Data transfer to alarm monitoring station is protected object off Data about violation of protected zone power supply fault malfunction of the Users are informed about all events 1 1 backup battery malfunction of the fire with SMS messages zone is transferred Periodical test signal can be sent All above mentioned data is transferred 2 plus information about arming and disarming In order that GsmAlarm 500 would send test message to the alarm monitoring station once per day it is necessary to set system clock see Ch 5 3 4 and program 24 hour timer see Ch 5 3 5 If data transfer mode is on Y value is above zero all calls are addressed to alarm monitoring station only i e GsmAlarm 500 users ALRNR1 ALRNRS don t get calls without reference to programmed M parameter value see Ch 5 3 1 12 In this case short call function is on only GsmAlarm 500 responds to user call with short call and can inform user about arming and disarming with short call If H value is H01 or H02 object is protected by security service only i e users ALRNR1 ALRNR5 will not get information about trespass disconnection of the main power supply arming and disarming User can receive inform
6. BYP Key Bypass Programming ccccccecsseesscesseesseeseesseceseceeeceeeeeceecseeeeeeeneeeeeeneess 41 8 1 5 CLEAR KEY onenn inve e EE Giantess aca een EAE naa 41 81 6 ENTER KEY sirrererooneinisinyii aniria eie AE EErEE E ETEA REEE REEE 41 8 1 7 4 MGIC AGO ni E E E EE A E R 41 8 1 8 StayD Status Indicator ec cececscesccesecesecesceeseeeseceseceseceseceeceseceeceseceseenseseeeeseeeneees 41 8 1 9 OFF Indicator sesiis eiiie iieii EE EEEE EE nae Ee Te 41 8 1 10 ARM SLEEP and STAY Indicators isiscccs iiss seesinuasilicaha taciadsayninessiudutidatiusonslcaieiutbees 41 8 2 Regular Armin sesrsereserstrei triennis troonis unk vbacatedaieesncead ENAS EET eaten EE ETAN EPER tetera Se rRNA nen eira 42 8 3 Stay amp Sle p arming ieii atin E EE E ance 42 GsmAlarm 500 Software ver 1 04 TABLE OF CONTENS 8 4 Disarming amp Deactivating an Alarm 0 cc ecceccccesscesseeseeesecseeesceeeeeseecseesseeeseceseesseesueenseeseeesees 43 8 5 Panic PU AIS ossessi sis EREE EE AE atau pee EEE EEE E OE EEEE 43 8 6 Programmable output control oros E E eed 43 9 System Control Using iButton Access Keys ccccccccsesscesnecssneeeeeeeesaeeseneeseaeeceaeeseaeensaeeesaees 43 10 Remote Arming amp Disarming cccccccccecccsssecesseesseeeececsseecseeceseecsnecseaeesseeeeeeeenseeessaeenses 44 11 System Operation in Alarm State 0 0 cece ceccescceeeceseceeeeseceseceaecene
7. The set time should be multiplied by 100 to obtain the time in milliseconds The range of possible values 01 99 x100 ms 0 1 s 9 9 s GsmAlarm 500 Software ver 1 04 29 PROGRAMMING Parametras Parametras Response time of zone Z1 Response time of zone Z9 Response time of zone Z2 Response time of zone Z10 Response time of zone Z3 Response time of zone Z11 Response time of zone Z4 Response time of zone Z12 Response time of zone Z5 Response time of zone Z13 Response time of zone Z6 Response time of zone Z14 Response time of zone Z7 Response time of zone Z15 Response time of zone Z8 The factory default values for all zones 05 500ms 5 7 10 OPERATING TIME OF OUTPUTS C1 C4 K1 K2 Output operating time if output operates in impulse mode Possible values 00 99 Parameter Operation time of output C1 in seconds Operation time of output C2 in seconds Operation time of output C3 in seconds 144 Operation time of output C4 K1 K2 in minutes In siren mode operation time is in minutes in all other modes in seconds Manufacturer programmed time C1 00 sec C2 05 sec C3 00 sec C4 K1 K2 02 min 5 7 11 OPERATING MODE OF OUTPUTS C1 C4 and BELL Possible operating modes are described in detail in Chapter 5 3 2 1 Address Parameter 321 Operating mode of output Cl Operating mode of output C2 Operating mode of output C3 Operating mode of output C4 Manufacturer progra
8. mode operates analogue to M04 thus it is activated only if short call number coincides with programmed numbers M06 Siren mode M07 Siren mode with audible confirmation After arming one short audible beep is heard After disarming two short audible beeps are heard Output is activated in case of wiring trouble of fire sensor Output is activated in case of AC mains failure Output is activated in case of GSM signal loss Additional audible buzzer mode Output state depends on the state of zone Z9 M24 M25 Output state depends on the state of zone Z15 If zero operating time is programmed T00 output is activated when adequate zone is open and deactivated when adequate zone is closed If not zero delay time is programmed output is activated automatically when adequate zone is opened and deactivates automatically after expiration of the programmed time 7 Outputs are controllable when system is armed or disarmed GsmAlarm 500 Software ver 1 04 19 PROGRAMMING 5 3 2 2 PARAMETER E THE WAY USER IS INFORMED ABOUT ARMING DISARMING Addr 273 EXY Arm notification X Y Disarm notification All functions below are 0 0 All functions below are deactivated deactivated User is informed by SMS 1 1 User is informed by SMS User is informed with a short call 2 2 User is informed with a short call User is informed with a short call 3 3 User is informed with a short and
9. To set system clock and date e Press the ENTER key Enter your system installer code The lights ARM and STAY will flash e Enter the address 900 Light ARM is blinking and STAY turns off Time note is seen on keypad K32LCD display e Enter time in following format HHMM HH hours MM minutes For example if time 12 hours 45 minutes must be programmed enter 1245 After entering time four short beeps are heard and date programming mode is turned on automatically LED ARM is turned on constantly light STAY is off Date note is seen on keypad K32LCD display e Enter date in following format YYYYMMDD YYYY year MM month DD day For example if you have to program date year 2010 04 month 23 day enter 20100423 After entering date four short beeps are heard e Exit the programming mode by pressing key CLEAR 5 7 23 PROGRAMMING 24 HOUR TIMER User is able to program up to 10 independent timer events Each event is definable with event number instruction and event time Address given in the table bellow indicates event number Event instruction indicates function to be performed in programmed time e g SMS message to be sent related output activated deactivated etc Event commands are described in Chapter 5 3 4 1 To program the timer e Press the ENTER key e Enter your system installer code The lights ARM and STAY will flash Enter 3 digit address indicating event number The lights ARM a
10. Touch arming One touch arming allows you to arm the system without using an access codes Press and hold the ARM key for 3 seconds to arm the system 8 3 STAY amp SLEEP ARMING Stay arming method allows you to roam freely within the premises while the perimeter is fully armed Stay zones are zones that are bypassed when Stay arming For example if you plan on staying in for the night doors and windows can be armed without arming other zones like motion detectors Stay arming Close all zones in the desired partition except Stay zones Press the SLEEP key e Fnter a 4 digit or 6 digit user access code Similar to Stay arming Sleep arming allows users to remain in a protected area but provides a higher level of protection For example in a two story house the perimeter is protected with Stay arming With Sleep arming the perimeter as well as the main floor are protected motion detectors etc allowing you to roam the second floor and sleeping quarters Sleep zone are zones that are bypassed when Sleep arming For example when you go to sleep at night the entire premises except your bedroom is fully armed GsmAlarm 500 Software ver 1 04 42 SYSTEM CONTROL Sleep arming Close all zones in the desired partition except Sleep zones e Press the SLEEP key e _ Enter a 4 digit or 6 digit user access code Stay and Sleep arming can also be activated using 24 hour timer or One Touch arming Press an
11. activated automatically You may contact your GSM service provider to inquire about activation of the GPRS service The second condition The GSM module or the computer that is used for connection to the GSM module should have unique IP addresses A unique IP address also is called a real address or an external address An external IP address is accessible from any internet connected computer An IP address to the GSM module is automatically provided by the GSM network Inquire your GSM GsmAlarm 500 Software ver 1 04 34 PROGRAMMING service provider to find out if your SIM card has a unique IP address Inquire your ISP to find out if your computer has a unique IP address There are two ways to connect to a GsmAlarm module over the internet The first method the user connects to the GSM module the module operates as a server This method is possible only if the GSM network has assigned an unique IP address to the module The user sends an SMS message to the GSM module AAAAAAAA GETIPA or if SMS password is deactivated The GETIPA command activates the GPRS interface of the GSM module and the server mode The GSM module sends connection data to the user the IP address and the port number The user should mark the option Connect to GSM module in the window Connect over GPRS enter the IP address and the port number click the button Connect and wait for establishment of connection The second method th
12. for indication of Z11 Z15 zones if K636 K10V or K10H keypad is used In the main indication mode keypad keys 1 10 are alight if zone corresponding alight number is open For example if Z1 zone is open key 1 is alight If Z10 zone is open key 10 is alight If key O is alight constantly it shows that there are open zones in the group Z11 Z15 After pressing extended indication mode is turned on is flashing In this case Z11 zone is corresponded by key 1 Z12 key 2 Z15 key 5 Extended indication mode is switched off after pressing once again or after pressing CLEAR 8 1 2 TBL KEY TROUBLE DISPLAY If key TBL is alight it indicates system failure Press TBL to check the failure type TBL starts to flash and alight keys 0 9 indicate failure type Alight key Failure No backup battery connection or the battery voltage is getting low AC power failure The system could not communicate with the alarm monitoring station A wiring trouble on a fire zone System clock loss GSM connection failure To deactivate trouble display mode press TBL key one more time or press CLEAR key System s clock should be set only system timer function is used System clock deregulates in case main power supply and backup battery are disconnected System clock setting with SMS message directions described in Chapter 5 3 4 System clock setting with keypad described in Chapter 5 7 22
13. or over current condition Open circuit breaker must have a gap between connections of more than 3mm System GsmAlarm 500 is a device mounted in limited access areas Any system repairs must be done only by qualified safety aware personnel There are no parts you can change at place in the device The system must be used only with approved back up battery to avoid fire or explosion hazards Special care must be taken connecting positive and negative battery terminals The device is switched off by 2 pole circuit breaker and disconnecting back up battery connector Mains power and back up battery must be disconnected before any installation or tuning work starts The system installation or maintenance must not be done during stormy conditions GsmAlarm 500 Software ver 1 04 GENERAL INFORMATION Remote control and monitoring device GsmAlarm 500 has built in radio transmitter operating on GSM900 and GSM1800 networks Do not use the device where it can cause interferences and danger Do not arrange the device close to medical equipment and appliances Do not use the device in explosive environment Device is not resistant to moisture chemical materials or mechanical damage equipment should be disposed at the end of life separately from your household wastes There are separate collection systems for recycling in EU For more information please et This symbol on the product or on its packaging means that your electric
14. responsibility for GSM network services coverage and functioning GsmAlarm 500 system provided with 24 month warranty Warranty period starts with purchase date If there are no purchasing documents period counted starting from system manufacturing date dated on security system identification label Warranty is not valid if system is reconstructed wrongly assembled used not on purpose mechanical chemical electric damage and in other cases that are not related with GsmAlarm 500 manufacturing defects are seen If security system is not operating properly or breaks down for guarantee or post guarantee service please contact company that performed assembling and installation of the system Practice shows that main system operating failure reason is incorrectly performed system assembling Company Elektronin s technologijos declares that product GsmAlarm 500 satisfies all essential requirements of standard EN 60950 1 2003 following European Union directive 2006 95EC GsmAlarm 500 Software ver 1 04 49 TECHNICAL CHARACTERISTICS 16 TECHNICAL CHARACTERISTICS GSM MODULE Operating frequency GSM 850 MHz EGSM 900 MHz DCS 1800 MHz PCS 1900 MHz MAIN POWER SUPPLY connected to terminal AC Power supply voltage AC 16 24V Frequency AC 50 60Hz Maximum current 1 2A max BACKUP BATTERY Backup battery operating voltage Backup battery type PB acid Backup battery capacity 1 2 Ah max OUTP
15. 01 Responding to unrecognized caller ID and number of calls in the case of F S01 alarm Outputs operating mode inverted not inverted OoOo 321 324 Output operating mode M C01 C04 331 345 Pulse counting mode I Z01 Z15 401 420 Timer events STIMER 900 Time and date programming SCLOCK parameters if programming by SMS message 281 295 Zone operating mode dividing into the partitions and partial protection P Z01 Z15 modes STAY and SLEEP GsmAlarm 500 Software ver 1 04 25 PROGRAMMING 5 7 1 PROGRAMMING ACCESS CODES Access codes are personal identification numbers that allow you to enter certain programming modes arm or disarm your system as well as activate or deactivate programmable outputs The system supports installer code and 20 user access codes User access code can arm or disarm the system activate or deactivate programmable outputs The installer code is used for the system programming only Your system can be programmed to use either 4 or 6 digit access codes see Ch 5 7 19 where each digit can be any value from 0 to 9 Six digit codes are considered more difficult to crack and therefore more secure To program an Access Code e Press the ENTER key Enter your system installer code default code is 0000 or 000000 The lights ARM and STAY will flash Select a user by entering a 3 digit user number e g 001 for user 1 or 020 for user 20 The lights ARM and STAY wi
16. 1234567893 Specified numbers will be deleted and user receives the confirming SMS DELETED 3701234567891 DELETED 3701234567892 DELETED 3701234567893 Up to 8 user numbers might be deleted with one SMS message GsmAlarm 500 Software ver 1 04 PROGRAMMING In order to receive SMS message indicating all programmed numbers following message must be sent to GsmAlarm 500 AAAAAAAA NRLIST User receives one or more SMS messages with all programmed numbers listed Note Up to 8 user numbers can be sent in one SMS message If 250 numbers are programmed GsmAlarm 500 will send 32 SMS messages 5 3 PROGRAMMING SYSTEM PARAMETERS WITH SMS All GsmAlarm 500 input and output operating modes delay times and names can be programmed with the help of SMS First it is recommended to receive SMS with programmed parameters and then to send the same SMS with corrected parameters back to GsmAlarm 500 5 3 1 PROGRAMMING ZONES In order to receive SMS with zone Z1 Z15 parameters send GsmAlarm 500 the following SMS AAAAAAAA ZPARAM SMS can be sent from any GSM phone not necessarily the user s GsmAlarm 500 confirms receiving the message with frequent blinking of MODE indicator and sends four SMS messages including input parameters Z1 Z15 First message contains Z1 Z4 parameters second Z5 Z8 third Z9 Z12 and Z13 Z15 parameters in fourth SMS message Received message with input Z1 Z4 parameters will look
17. 3 2 5 PARAMETER L SMS STRUCTURE AND SMS MANAGEMENT PASSWORD Adr 237 SMS Structure LXY SMS Management Password All bellow described functions are 0 0 SMS password deactivated The deactivated system can be configured by anybody who knows the system telephone number SMS message contains a number of 1 1 SMS commands are executed if SMS triggering events after the zone name sender is one of the five users ALRNR1 ALRNR5 SMS message contains the name of the user 2 2 SMS commands are executed only if that armed or disarmed the system the password at the beginning of SMS matches the stored password Warning SMS messages failure and 4 restoration of power supply low battery detection of GSM jamming are sent to all ALRNR users not only to ALRNR1 Manufacturer programmed value L32 Important To activate several functions the total of numbers should be used Example To activate all three functions the digit X should be 7 1 2 4 7 5 3 3 PROGRAMMING PARTITION NAMES If it is necessary to secure two objects and system is divided into two partitions user can program names of the partitions It is possible to receive a message with names of the partitions after sending to GsmAlarm 500 following message AAAAAAAA RPARAM GsmAlarm 500 sends SMS message with available names of the partitions AAAAAAAA R1 PARTITION1 R2 PARTITION2 After correction of the names SMS message is
18. APROG The computer allows programming deletion and assigning of iButton keys to a specific user and setting up of key control functions The GSM alarm configuration tool is downloadable from the website of the manufacturer www eltech It Without a computer only programming of new keys is possible Deletion and setup of programmed keys is impossible The key programming mode is activated by the DIMF SMS command 71 see Ch 14 The key programming mode is indicated by a rapid blinking of the MODE indicator In the programming mode a key is attached to the reader for 2 3 seconds Completion of the key code capture is confirmed by a very rapid blinking of the MODE indicator After programming of all keys the key programming mode should be deactivated It may be done by the DIMF SMS command 70 or by switching off and on the system power supply 5 9 PROGRAMMING AND DIAGNOSTICS OVER THE INTERNET The system parameters may be changed and the system status may be observed by connecting over the internet The data are transmitted according to TCP IP protocol the GSM module connects to the internet via a GPRS cannel The connection is established by the GSM alarm configuration tool GAPROG The application is downloadable from the website of the manufacturer at www eltech It Two conditions are necessary for connection over the internet The first condition GPRS service should be activated for the SIM card of the GSM module Usually GPRS service is
19. Ch 7 3 7 1 PROGRAMMING TELEPHONE NUMBERS OF THE ALARM MONITORING STATION Alarm monitoring station telephone number numbers is are provided by security service that protects particular object Telephone numbers are programmed in the same way as user numbers see Ch 5 2 1 and 5 2 2 In most case one number CIDNR1 is sufficient It is recommended to program with international code 370 7 2 PROGRAMMING CONTACT ID USER ACCOUNT NUMBER Four digit user account number is provided by security service that protects object Programming can be performed with keypad see Ch 5 7 24 or with SMS message In order to program the account number following SMS is sent AAAAAAAA CIDACC 1234 AAAAAAAA SMS password CIDACC programming command 1234 four digit user account number Important a no characters or spaces can be used before the password b no spaces are allowed before and after the colon If number programming command was performed successfully the user receives SMS with programmed identification number In order to get programmed account number following SMS message is sent AAAAAAAA CIDACC GsmAlarm 500 Software ver 1 04 37 PROGRAMMING 7 3 MODES OF DATA TRANSFER TO THE ALARM MONITORING STATION Addr 233 Modes of data transfer to the alarm monitoring station are determined by general system parameter H H parameter can be programmed with SMS message see Ch 5 3 2 or with keypad see Ch
20. ERMINAL AUX The auxiliary power supply can be used to power motion detectors and other devices requiring 12 VDC AUX is short circuit protected Max load current is 1 A 2 4 PROGRAMMABLE OUTPUT TERMINALS C1 C2 and C3 The programmable output is a 150 mA maximum switch to ground A 33 ohm current limiting resistor is connected in series A small relay a buzzer or other DC operated device may be connected between the 12 VDC AUX positive terminal and the C switched negative terminal on the main board Relays with 12V operating voltage and current not exceeding 150 mA max are recommended for device control Output operating modes are described in Ch 5 3 2 1 Equivalent diagram of C output 2 5 BELL SIREN CONNECTION TERMINALS K1 and K2 These terminals are relay contacts of the programmable output C4 K1 and K2 are used to connect audio siren or extra commutated device Commutated current may reach 5 A max 2 6 AC POWER TERMINALS Use a 16 18 VAC transformer with a minimum 40 VA rating to supply AC power to the GsmAlarm 500 2 7 BATT CONNECTOR Use this connector to connect the backup battery Max capacity of the backup battery is 1 2 Ah Voltage 12 VDC 2 8 EXTERNAL MICROPHONE CONNECTOR This connector is used to connect an external microphone Connect white wire to contact M black to M In order to avoid interference install microphone as far
21. GsmAlarm 500 V1 04 C GSM Alarm and Remote Control System LAES E SES SSETTITETI TITTI En em gt m Wier FEATURES 6 inputs Up to 15 protection zones 3 programmable low current outputs 1 high current relay output 5 users are notified Possibility to connect up to 4 keypads 20 programmable keypad access codes or iButton keys Automated remote control using up to 250 number Caller ID recognition without call cost Remote control using mobile phone keypad through DTMF tones 24 hour timer Two partial protection modes STAY and SLEEP Possibility to divide the system into two independent partitions Possibility to send information to alarm monitoring station using the Contact ID protocol through GSM voice call Possibility to connect up to 6 temperature sensors for temperature measurement Info carrying SMS showing state of each sensor power supply voltage GSM signal strength GSM JAMMING detection Programming and firmware upgrade via USB connection Remote programming over GPRS Integrated quad band GSM module Wide operating temperature range 35 65 C GsmAlarm 500 Software ver 1 04 TABLE OF CONTENS Table of Contents 1 General Ufornm ationn ies isi s25 e255 sos0c22sssdesandenc ions banc idavetsa ane thee oe shen dorsadiceahi idee dige UG eaa aA E TSA 1 1 1 Safety Instr ctionS ones tes saranda sea aah cascada capac cule va awa umes EERE au ETE ESNS 1 1 2 Package Content asne
22. K words informing about state of the zone GsmAlarm 500 Software ver 1 04 23 PROGRAMMING 5 5 PROGRAMMING USER NAMES Each user of a keypad or a iButton key can be assigned a name that is indicated in the SMS message of arming or disarming of the system Up to 20 user names can be programmed The following message is sent to GsmAlarm 500 to receive an SMS message with the user names AAAAAAAA UPARAM GsmAlarm 500 sends 3 messages with user names to the user AAAAAAAA U01 User1 U02 User2 U03 User3 U04 User4 U05 User5 U06 User6 U07 User7 A corrected SMS message is sent to GsmAlarm 500 The user receives a confirmation SMS message with the user names The maximal length of a user name 16 characters 5 6 PROGRAMMING SMS PASSWORD In order to change manufacturer programmed SMS password send GsmAlarm 500 the following message AAAAAAAA PASSW ABCDefgh AAAAAAAA old SMS password PASSW password changing instruction ABCDefgh new SMS password Password must be 8 characters long Note No characters spaces can be used before password space must follow the password If programming instruction is executed successfully user gets a confirming SMS message with the new SMS password GsmAlarm 500 Software ver 1 04 24 PROGRAMMING 5 7 PROGRAMMING THE SYSTEM USING THE KEYPAD All system parameters except for user phone numbers and names of zones and outputs are programmable using keypa
23. LEEP mode 80 disarms the first partition 90 disarms the second partition When the code is entered call is automatically ended Depending on system settings user receives confirmation call or and SMS message For example SYSTEM ARMED STAY MODE USER1 If system is divided into two partitions names of protected objects partitions can be seen in the SMS message OBJECT 1 SYSTEM ARMED SLEEP MODE USER OBJECT 2 SYSTEM DISARMED USER2 System can be configured to arm and disarm by short free call see Chapter 5 3 2 3 In order to to arm the system user calls GsmAlarm 500 number and hearing the first signal cancels the call In this case there is no exit delay the alarm system is activated immediately After the armed mode is on user receives a short confirmation call or SMS Don t cancel the confirmation call because it is cancelled automatically You can disarm the system by calling GsmAlarm 500 number and waiting for the system cancels the call 3 4 call signals The alarm system also can be armed or disarmed by SMS message In the beginning of the message 8 digit password is entered and further command is written For example AAAAAAAA 01 GsmAlarm 500 Software ver 1 04 44 SYSTEM CONTROL 11 SYSTEM OPERATION IN ALARM STATE In the case of trespass of the protected area GsmAlarm 500 depending on the programmed system operation algorithm switches the siren on calls and sends SMS messages to f
24. NGS TO FACTORY DEFAULTS In order to reset all system parameters to factory default settings press and hold the RESET button for five seconds The MODE LED will start flashing Within 2 seconds of this flashing press the reset switch again The panel will reset to default and restart Only the parameters stored in the internal memory module system can be restored using this method User umbers stored in SIM card will not be erased 6 1 MANUFACTURER PROGRAMMED PARAMETERS Zone2 Addr 201 202 203 204 Pr A A30 A30 A30 A30 Input parameters Ardr Pr M 241 M70 242 243 244 M70 7 70 Adrr 281 282 283 284 PrP P10 P10 P10 Zone4 Zone5 n 205 206 207 208 209 210 fl 430 430 452 A00 A00 A00 245 246 247 248 249 70 70 7 7 70 70 285 286 287 288 289 Ls P10 334 106 104 T00 P10 335 106 105 TO 336 106 106 T00 P10 P10 337 106 107 T00 P10 P10 339 106 109 T00 290 291 292 293 294 295 Zonell ee ee irs AJ als SIS bee bed 211 212 213 214 215 A00 A00 A00 A00 A00 70 I fl ff m N N Nn Nn N eE S P10 341 106 111 700 P10 P10 P10 P10 I ma Ly JL N Nn U ff M l fl fl fl N S I I N
25. Nn Nn S Output parameters N a m e Addr Param M Addr Operating time T Addr OutC1 321 141 T00 sec 320 143 T05 sec 324 M06 Common system parameters SMS E F G H K L P T 273 274 033 233 2381 237 236 100 Password PGM Output Invert Addr parameter address when programming with the keypad GsmAlarm 500 Software ver 1 04 36 PROGRAMMING 7 DATA TRANSFER TO ALARM MONITORING STATION User can choose object protection way gt individual protection when SMS messages and calls are addressed to user only gt combined protection when information about state of the object is received both by security service and user gt protection by security service only Data is transferred to the alarm monitoring station by Standard CONTACT ID protocol through GSM voice call while Standard CONTACT ID protocol is understandable to all modern alarm monitoring stations GsmAlarm 500 transfers data about violation and restoring of alarm zone arming and disarming power supply fault malfunction of the backup battery malfunction of the fire zone Test messages can be sent on certain time In order to activate function of data transfer to the alarm monitoring service it is necessary to program one or two numbers of alarm monitoring station see Ch 7 1 to program four digit user account number see Ch 7 2 and choose appropriate protection mode see
26. SMS message call and SMS message Manufacturer programmed value E20 5 3 2 3 PARAMETER F SYSTEM RESPONSE TO INCOMING CALLS AND NUMBER OF CALLS IN ALARM STATE Addr 274 System response to incoming call FXy Number of the calls in alarm mode All functions below are deactivated Ifa call is received from unknown 1 caller user ALRNR1 will receive a SMS with caller s number 1 After alarm triggering users are called once If calling from user s number after 2 2 Users are called twice 3 4 calls the system will pick up armed mode will remain on Armed mode is activated after user s 4 3 Users are called 3 times short call Manufacturer programmed value F31 Note If several functions have to be operative sum of the numbers is used E g for all three X functions to be active X value must be 7 1 2 4 7 5 3 2 4 PARAMETER G SMS DELAY TIME IN CASE OF POWER SUPPLY FAILURE Addr 139 In the case of the mains 230V power supply failure message is sent to user and or alarm monitoring station only after programmed period If G 0 G00 reports about failure and re connection of the main power supply voltage wouldn t be generated Possible delayed time values G01 G99 in minutes After recovery of the main power supply report will be send after 1 minute period of time This time can not be programmed GsmAlarm 500 Software ver 1 04 20 PROGRAMMING 5
27. TER ZONE TRIGGERING Parameter M defines system response to the violation of alarm zone and which users are informed if certain zone sensors are triggered It is described in detail in Chapter 5 3 1 2 Address Parameter Address Parameter 241 Zone Z1 M parameter 249 Zone Z9 M parameter Zone Z2 M parameter 250 Zone Z10 M parameter Zone Z3 M parameter Zone Z11 M parameter Zone Z4 M parameter Zone Z12 M parameter Zone Z5 M parameter Zone Z13 M parameter Zone Z6 M parameter Zone Z14 M parameter Zone Z7 M parameter Zone Z15 M parameter Zone Z8 M parameter Manufacturer programmed values for all zones 70 GsmAlarm 500 Software ver 1 04 28 PROGRAMMING 5 7 7 PARAMETER P PARTITION ASSIGNMENT AND PARTIAL ARM METHODS This parameter is defining if zone is operating in full or partial protection mode Possible operating modes are described in detail in Chapter 5 3 1 3 Parameter Parameter Zone Z1 P parameter Zone Z9 P parameter Zone Z2 P parameter Zone Z10 P parameter Zone Z3 P parameter Zone Z11 P parameter Zone Z4 P parameter Zone Z12 P parameter Zone Z5 P parameter Zone Z13 P parameter Zone Z6 P parameter Zone Z14 P parameter Zone Z7 P parameter Zone Z15 P parameter Zone Z8 P parameter Def
28. UT AUX FOR EXTERNAL DEVICES Output voltage Maximum current 1A max Short circuit protection triggering current 2 A max PROGRAMMABLE OUTPUT C4 K1 K2 Output type Relay contacts Maximum current 5 A max Active state Closed contacts Non active state Open contacts PROGRAMMABLE OUTPUTS Cl C2 C3 Output type Open collector Maximum current 150 mA max Output active Connected to GND Output non active Open contact INPUTS Z1 2Z6 Load resistor in EOL or ATZ mode 2 2 kQ 10 4 7 KQ 10 Temperature measurement range in temperature measurement mode 40 C 110 C 1 C POWER CONSUMPTION without external sensors and keypad Non activated state Call sending SMS or speech mode 350 mA max OPERATING TEMPERATURE 35 C 65 C DIMENSIONS 99 x 83 x 25 mm ELEKTRONINES TECHNOLOGIJOS http www eltech It GsmAlarm 500 Software ver 1 04 50
29. al and electronic contact the local authority or the dealer where you purchased the product 1 2 PACKAGE CONTENT Main board GSMA 500 cecceseesseesceessceeeeeeeseceseceseseeeceeeeseesseeseeeseesseens Qnty 1 GSM antenna with magnetic fix and 2 m lead cable ceceeceeceeseeteees Qnty 1 MiGrophOme iss ccf 5sstvescessecess seteced baciavecdats r A E EE Qnty 1 Microphone connector ccccccsssesssssseeseceseesseeeseeeseessecsseeeseceseceseeeseesseenses Qnty 1 Load resistors 2K ES sinian A bites nea Qnty 6 Load resistors 4 7k 5 cccccccssscssssccscessscessssecsssecsscesssecesscecssceesseeesseecsues Qnty 7 Battery connection Wire ceccescesseeseeeseeseeesceeseeeseeeseeesecnseceseeeseeneeeeeeeseees Qnty 1 F sten Clips aeann tescoecaateests iio satereeenc ete ay es eet cee ttc ccesetanee Qnty 4 Users Mangal rentesi er e EEA ERA EE aa TEE ESEE Qnty 1 GsmAlarm 500 Software ver 1 04 GENERAL INFORMATION 1 3 INTRODUTION GsmAlarm 500 can be used for protection of houses apartments cottages and other buildings In the case of trespass of the protected zone GsmAlarm 500 depending on the programmed system operating algorithm can switch the siren on call and send SMS messages to five users and transfer information to the alarm monitoring station by Contact ID protocol through GSM voice call User answers the call can listen what is going on in the unit and control the system using his mobile phone keypad th
30. ally closed contacts NO normally open contacts A1Y A4Y zone operating modes parameter A see Chapter 5 3 1 1 GsmAlarm 500 has 6 inputs Z1 Z6 corresponding to the zone numbers Z01 Z06 If 6 zones are sufficient for protection of the object the inputs may operate in non EOL or EOL modes A load resistor 2 2k is used in EOL mode In this case the system activates both at short cutting the circuit and at breaking the circuit The resistor is mounted in the housing of an alarm sensor If 6 zones are insufficient an advanced technology zone ATZ mode may be used In this case one input can control two zones Two parallel connected resistors are used in ATZ mode Load resistors of 2 2k are associated with the zones Z01 Z06 Load resistors of 4 7k are associated with the zones Z07 Z15 The number of the main ATZ zones Z01 Z06 should correspond to the number of the extended ATZ zones Z07 Z15 The main and the extended zones are associated automatically in the order of increasing zone number Example If ATZ mode has the main zones Z01 Z02 Z04 and the extended zones Z08 Z09 Z10 the zone Z01 will be associated with zone Z08 zone Z02 with zone Z09 and zone Z04 with zone Z10 If a 2 wire fire sensor is connected to the programmable output C3 the zone Z07 should be set as an additional fire zone ASY mode see Ch 5 3 1 1 and the output C3 should work in the following mode M01T05 inverted see Ch 5 3 2 and Ch 5 7 11
31. arm 500 Software ver 1 04 47 SYSTEM CONTROL code 0 is entered In order to turn off zone Z12 code 2 is entered Command 00 turns off BYPASS mode for the all zones Further listed commands are used for system programming by SMS message SMS instruction Function ZPARAM Request to send SMS message with input Z1 Z5 parameters CPARAM Request to send SMS message with output C1 C2 and BELL parameters Request to send SMS message with names of the protected objects partition names Request to send SMS message with user numbers ALRNR1I ALRNRS ALRNRI ALRNR2 ALRNR3 User numbers programming instructions ALRNR4 ALRNRS NRLIST Request to send SMS message messages with all numbers stored in SIM card SCLOCK System clock control and time setting instruction STIMER Request to send SMS message with system timer parameters Default ALARM see Ch 5 4 Default OK see Ch 5 4 GSM module IP address and connection port number CONNECT Activation of GPRS connection client mode request to send SMS with computer IP address and connection port number SMS instructions for system programming and diagnostics GsmAlarm 500 Software ver 1 04 48 WARRANTY 15 WARRANTY MANUFACTURER AND DISTRIBUTOR is not responsible for possible theft from GsmAlarm 500 protected premises GSM service operators are not associated to company UAB Elektronin s technologijos therefore company takes no
32. as follows AAAAAAAA Z01 A30M70P10106T20 Zonet Z02 A30M70P10106T00 Zone2 Z03 A30M70P10106T00 Zone3 Z04 A30M70P10106T00 Zone4 AAAAAAAA password Z zone input number A30 parameter defines operating mode of the corresponding input see Ch 5 3 1 1 M70 parameter defines system response to the violation of protected zone and which users are informed if certain zone sensors are triggered see Ch 5 3 1 2 P10 partial protection mode see Ch 5 3 1 3 106 the pulse counting mode When the first number is larger than 1 the zone operates in the pulse counting mode After the zone triggers N number of times during the preset duration the system switches over to the alarm state N the first digit The second number establishes the duration of pulse counting Multiplication of this number by 10 produces the time in seconds Minimal time 10 seconds 1 maximal time 90 seconds 9 The factory preset time 60 seconds If N 0 or N 1 the pulse counting mode is switched off GsmAlarm 500 Software ver 1 04 15 PROGRAMMING T20 entry delay If the system is armed and relevant input is triggered the system switches siren on and sends SMS only after expiration of the given delay time Possible values 0 99 seconds If zone is in temperature measurement mode value of T parameter corresponds to triggering temperature see Ch 5 3 1 1 Possible values 0 99 C Zonel Zone2 Zone3 Zone4 zone names which a
33. as possible from GSM antenna 2 9 RESET BUTTON RESET button is used to restore factory default settings see Ch 6 GsmAlarm 500 Software ver 1 04 LED INDICATORS 3 LED INDICATORS 3 1 NETWORK GSM MODULE STATE AND SIGNAL STRENGTH INDICATOR Indicator state Explanation GSM module is not in use No power supply or system failure There is no GSM operator network registration Continuously On Possible causes SIM card PIN code request is not deactivated antenna not connected or poor network connection quality Blinking more frequently than once a GSM module is in use outgoing call or SMS is second being sent Weak connection 3 2 MODE ALARM SYSTEM STATUS INDICATOR No power supply or system failure System is operative disarmed no zone sensors have Continuously On been triggered On with short breaks System is operative disarmed but one or more zone sensors have been triggered Blinking with low frequency once in System is armed 2 3 sec Blinking more frequently than once a System is in alarm state second Blinking very rapidly for 2 3 sec SMS instruction or DTMF command receipt confirmation GsmAlarm 500 Software ver 1 04 INSTALLATION 4 INSTALLATION 4 1 GENERAL INSTALLATION INSTRUCTIONS According to manufacturer recommendations hire qualified security system specialist or company to perform system installation works Self dependent installation of the sy
34. ation about the object only after sending appropriate SMS message or after calling to GsmAlarm 500 number and entering appropriate DTMF code If H value is H11 or H12 GsmAlarm 500 is operating in combined protection mode and firstly calls and transfers information to the alarm monitoring station and afterwards is proceeding in standard algorithm and informs users about event with SMS message If after eight attempts system isn t able to transfer information to the alarm monitoring station following SMS message is sent to the user Unable to connect to the alarm monitoring station GsmAlarm 500 Software ver 1 04 38 PROGRAMMING 7 4 CONTACT ID PROTOCOL CODES GsmAlarm 500 for data transfer is using following standard CONTACT ID protocol event codes It is impossible to change codes or program new codes CID code Transferred information 100 Panic alarm silent alarm GsmAlarm 500 Software ver 1 04 39 SYSTEM CONTROL 8 SYSTEM CONTROL USING THE KEYPAD The keypad allows you to easily access your security system s functions and provide you with an easy to understand display of your security system s alarm and operational status Keypad includes coloured lights which convey the current status of your system The state of each light represents a specific condition in your system 8 1 KEYPAD KEYS AND LED FUNCTIONALITY 8 1 1 KEY EXTENDED INDICATION MODE Key can be used
35. ault values for all zones programmed by manufacturer 10 5 7 8 PARAMETER I PULSE COUNTING MODE If the first digit of this parameter is larger than 1 the zone operates in the pulse counting mode After triggering of a zone the number of times Ni during the preset time Ti the system switches over to the alarm state The first digit the number of triggering events Ni The second digit the pulse counting time Ti Multiplication of the second number by 10 produces the time in seconds Minimal time 10 seconds 1 maximal time 90 seconds 9 If Ni 0 or Ni 1 the pulse counting mode is switched off Adresas Parametras Adresas Parametras 331 I parameter of zone Z1 339 I parameter of zone Z9 332 I parameter of zone Z2 340 I parameter of zone Z10 I parameter of zone Z3 I parameter of zone Z11 I parameter of zone Z4 I parameter of zone Z12 I parameter of zone Z5 I parameter of zone Z13 336 I parameter of zone Z6 I parameter of zone Z14 337 I parameter of zone Z7 1 parameter of zone Z15 parameter of zone Z8 The factory default values for all zones 06 5 7 9 ZONE RESPONSE TIME This parameter indicates the duration of presence of a constant signal at the input that is required for the system to register an alteration of the zone status The system becomes increasingly resistant to interference with increase of this time
36. ber send the following SMS AAAAAAAA ALRNR2 N Number ALRNR2 is deleted user receives SMS with programmed numbers In order to replace one number with another no separate instruction for deletion needs to be sent In order to receive SMS with programmed numbers ALRNR1 ALRNRS send GsmAlarm 500 the following SMS AAAAAAAA NRINFO Extra user numbers only for gate control are programmed by sending the following SMS AAAAAAAA ADDNR 3701234567891 ADDNR 3701234567892 ADDNR 3701234567893 ADDNR new number programming instruction 3701234567891 new user number If the numbers programmed successfully the user who sent the message receives SMS with newly programmed number In this case the confirmation message will be USER1 3701234567891 USER2 3701234567892 USER3 3701234567893 USER name assigned to the new number If a short call controls several outputs an additional number may be assigned only to a single output In this case the programming message is the following AAAAAAAA ADDNR C1 3701234567891 ADDNR C2 3701234567892 ADDNR C3 3701234567893 ADDNR C4 3701234567893 The first number controls only the output C1 the second C2 the third C3 the fourth C4 K1 K2 Up to 8 user numbers might be programmed with one SMS message In order to delete the extra user number send to GsmAlarm 500 the following message AAAAAAAA DELNR 3701234567891 DELNR 3701234567892 DELNR 370
37. cator MODE SMS with current system parameters is being sent AAAAAAAA C1 M01T00 OutC1 C2 M05T05 OutC2 C3 M01T05 OutC3 C4 M06T02 Siren S01 E20F31G01H00J00K00L32P00T20 C1 number of programmable output C4 corresponds to siren connection terminals K1 K2 M01 output operating mode see Ch 5 3 2 1 T00 output operating time Outputs C1 C3 in seconds C4 K1 K2 in minutes OutC1 OutC2 OutC3 and Siren programmable output names User can change the name under his own discretion Maximum number of name characters 16 S01 command for common system parameters programming E20 the way to inform user about arming disarming User can be informed by short call or SMS message see Ch 5 3 2 2 F31 system response to incoming outgoing calls and number of calls in alarm state see Ch 5 3 2 3 G01 SMS delay time in case of the main power supply failure see Ch 5 3 2 4 H00 modes of data transfer to the alarm monitoring station see Ch 7 3 J01 the system response to intentional GSM jamming Possible values JOO JO1 J02 J03 J00 detection of jamming signal deactivated JO1 an SMS message is sent to users after resuming of communication The message indicates the GSM jamming onset time J02 detection of GSM jamming signal activates the siren J03 operates as the functions JO1 and J02 K00 the method of system control K00 the system is controlled by a PARADOX keypad K01 the system is co
38. ceaeceaeceaeeeaeceneseeeseneseeesaeees 45 12 Power Supply Monitoring 00 eee ceceecceeceseceeceseeeeaeeeseeeseceaeceaeceaeceeeceaeceaeeeaeseneseeeeeeeseneeaeee 45 13 GSM Jamming Detection 00 0 0 ee eccecccseeeeceeeeeesceseeceaeceaeeeseceaeceaeceneceeecaesaeseeeceaeseeeseeeseneeaeees 46 14 System Control Using DTMF and SMS Command 0 ccc eeceeseeseeeceeeeeeeeceneeeeeeeeeeeneeaeees 47 15 WALT ACY 3 sscsiss ecescecsit sdetitceine et ianeds Hai deemed lea S a a REO eee dee 49 16 Technical Characteristics 0 0 00 eccecceeceeseeesceeceseeceaeceseeeseceaeceaeceneceseceaeseaeseeeseeeseeeeeeeseeeeaeees 50 GsmAlarm 500 Software ver 1 04 GENERAL INFORMATION 1 GENERAL INFORMATION 1 1 SAFETY INSTRUCTIONS Please read and follow these safety guidelines in order to maintain safety of operators and people around Retain all safety and operating instructions for future reference during the whole operating lifetime of device The system must be powered by main 16 24V 50Hz 1 5A AC or 18 24V 1 5A DC power supply which must be approved by LST EN 60950 1 standard and be easily accessible Any additional devices linked to the system GsmAlarm 500 computer sensors relays etc must be approved by LST EN 60950 1 standard External power supply must be reachable and can be connected to AC mains only inside installation room with automatic 2 pole circuit breaker capable of disconnecting circuit in the event of short circuit
39. ceseecsseeceeecseeeseecsteeesteeenees 34 5 9 Programming and Diagnostics Over the Internet c cc ccccceccceseceeeeeeseeeeeeeenteeenseeenens 34 6 Resetting system settings to factory defaults ccccsscceseeceneeeeseeesneeeeseeeeeessneeeeseeenseeess 36 6 1 Manufacturer Programmed Parameters cccccccccsseessceseeessceseeeseesseceseceseceseeeseceseenseeeeeseeseneees 36 7 Data Transfer to Alarm Monitoring Station 000 0 ccc cccccccccceseceeneeeeneeeeeeeeeeeeseeeseeenseeenseeess 37 7 1 Programming Telephone Numbers of the Alarm Monitoring Station ccceeeeeseeseeeeeeees 37 7 2 Programming CONTACT ID User Account Number ciccistiscccnsscoisiaiavescarnsavieseeternouaneivarsaeetiets 37 7 3 Modes Of Data Transfer To The Alarm Monitoring Station sicccscccsictvssidstestscdesuaanesnaseasiinese 38 7 4 CONTACT ID Proto l C d S icssissosir siseasi einiaid eiai 39 8 System Control Using the Keypad 0 ccccccccccccsscesseeceseeeeseeesseecnseeceseeeseeseseeceeeenseeseneeenseeess 40 8 1 Keypad Keys and LED Indicator Functionality 0 0 cccccccccsssesseesseeseceeeeseeeseceseesseeseeeseeeaeees 40 8 1 1 Key Extended indication mode oo ccccccccccceessesssessscesseeseesseesseceaeeeeeeseesseeeneesseeeas 40 8 1 2 TBL Key Trouble Display sisinesnsrensni ninina aaret 40 8 1 3 MEM Key Alarm Memory Display ccccccsccsseessseseeeseeesceeseeeseeeseesseceseeeseeneeeneeeseess 40 8 1 4
40. commended to install remote control relays into sockets which can be easily fixed to metal housing Operating current of relay coil can not exceed 150mA max Relays are selected depending on desirable commutative voltage and current Connection according to the wiring diagram presented in Chapter 4 2 1 is recommended if the system is controlled by a keypad Up to 4 Paradox K636 K10V H MGIOLEDV H K32 MG32LED or K32LCD MG32LCD keypads can be connected to GsmAlarm 500 Each of the said keypads has a single keypad zone the blue wire Use of keypad zones is recommended for connection of magnetic door sensors Activation of a keypad zone is described in Chapter 5 7 21 Connection according to the wiring diagram presented in Chapter 4 2 2 is recommended if the system is controlled by iButton DALLAS keys DS1990A or a simple switch Short beeps are generated by an ancillary buzzer while exiting a room and a continuous sound after entering the room Any buzzer with power supply of 12 V DC and maximum operating current of 100 mA may be used e g BPT 23CXW 1 The system status LED indicator woks in sync with the MODE indicator see Ch 3 2 The state of this indicator allows identification of the alarm system status and verification of closure of all protected zones before arming the alarm system The status indicator should be mounted indoors in a well visible location The reader DS9092LED of iButton keys is equipped with an embedded LED ind
41. d User numbers are programmed only by sending SMS message or by method described in Ch 5 2 1 names SMS message only To program system parameters e Press the ENTER key e Enter your system installer code default code is 0000 or 000000 The lights ARM and STAY will flash programming mode is activated e Select the parameter by entering a 3 digit address The lights ARM and STAY will lit constantly Enter a new 2 digit parameter Press the CLEAR key to exit the programming mode All parameters and addresses of the parameters are provided in the table Please see Chapters 5 7 1 5 7 25 for more detailed information Address Parameter description SMS parameters 000 Installer access code 4 or 6 digits 001 020 User access codes 4 or 6 digits a CONTACT ID user identification number CIDACC 031 050 User code function S o o Exit delay 101 115 Zone operating mode entry delay or triggering temperature T Z01 Z15 133 Delay time of report SMS about the failure of main power supply G S01 151 165 Zone responsetime o o S oo 234 User code length 4 or 6 digits o Sooo 235 Exit delay audible indication 237 SMS structure and SMS password functionality 238 GSMJAMMING notification S S O 239 Backup battery monitoring S S O M Z01 Z15 241 255 Input operating mode alarm state after input triggering M Z01 Z15 Informing users about arming and disarming E S
42. d hold the STAY key or the SLEEP for 3 seconds to arm the system 8 4 DISARMING amp DEACTIVATING AN ALARM To disarm an armed system or an alarm press OFF and enter your access code When an entry point is opened the keypad will beep until you disarm the system Your alarm system will not generate the alarm until entry delay time elapses 8 5 PANIC ALARMS In case of an emergency the system can provide three panic alarms that can immediately generate an alarm after simultaneously pressing and holding two specific keys for three seconds Based on your needs these panic alarms can generate audible alarms sirens or bells or silent alarms and can communicate specific messages to your monitoring station Pressed keys Panic alarm type 1 3 Silent alarm Message to alarm monitoring station is sent 4 6 Panic alarm Siren is on message to alarm monitoring station is sent 7 9 Fire alarm Siren is operating with interruptions message to alarm monitoring station is sent Panic alarm messages are sent to alarm monitoring station only if data transfer to monitoring station option is activated System doesn t call and doesn t send SMS messages to users 8 6 PROGRAMMABLE OUTPUT CONTROL The programmable output PGM terminal on the GsmAlarm 500 can be made to activate by a command from the keypad This output can be used for operating other devices such as garage door opener special lighting or door str
43. de System memorizes bypassed zones Constantly alight key BYP indicates there are some bypassed zones in system memory BYPASS memory is erased automatically after disarming the system If bypassed zone is operating in 24 hour mode BYPASS mode is not turned off automatically In this case BYPASS mode can be switched off only by keypad or in a remote way while calling and entering corresponding code or by sending SMS message 8 1 5 CLEAR KEY Use the CLEAR key to clear mistakes when entering user code etc or to return to main keypad mode 8 1 6 ENTER KEY Use the ENTER key to activate system parameter programming mode 8 1 7 AC MAINS INDICATOR This indicator is not alight when there is no 230 VAC power supply voltage and system is powered by backup battery only 8 1 8 StayD STATUS INDICATOR Indicator is on when all zones are closed and system is ready to be armed 8 1 9 OFF INDICATOR Indicator is on if the system is disarmed 8 1 10 ARM SLEEP and STAY INDICATORS Indicator ARM is alight constantly if the system is in full arm mode indicators SLEEP or STAY are alight constantly if the system is in partial arm mode In case of alarm these indicators flash fast GsmAlarm 500 Software ver 1 04 41 SYSTEM CONTROL 8 2 REGULAR ARMING This method will arm all the zones in the selected partition Check to see if the TBL or BYP light is on before arming the syste
44. e GSM module connects to the computer of the user the module operates as a client This method is possible only if a real unique IP address has been assigned to the computer of the user The user sends an SMS message to the GSM module containing the command CONNECT and the IP address of the user computer AAAAAAAA CONNECT 213 130 32 55 or CONNECT 213 130 32 55 The CONNECT command activates the GPRS interface of the GSM module and the client mode The GSM module sends an SMS message to the user containing the computer IP address and the connection port number The user should mark the option Wait for connection by GSM module in the window Connect over GPRS enter the port number click the button Wait and wait for the GSM module to connect to the computer The GSM module retries connecting to the specified IP address every 30 seconds The computer IP address that was included in the SMS message from the user is automatically saved in the GsmAlarm 500 memory Later the command CONNECT is sufficient to make the GSM module to connect to the same IP address AAAAAAAA CONNECT or CONNECT Important GPRS parameters of the GSM module should be correctly set up for GPRS interface to operate The GPRS parameters are configured via USB interface using GAPROG software The setup procedure is described in the manual of GAPROG software GsmAlarm 500 Software ver 1 04 35 6 PROGRAMMING RESETTING SYSTEM SETTI
45. ecking whether SIM card PIN code request is switched off take the SIM card off from the mobile phone and insert it into GsmAlarm 500 SIM card slot 5 2 2 PROGRAMMING WITH SMS In order to program the main user numbers send the following SMS from any mobile phone into GsmAlarm 500 AAAAAAAA ALRNR1 3706123456789 ALRNR2 3706123456789 ALRNR3 3706123456789 ALRNR4 37061234546789 ALRNR5 3706123456789 CIDNR1 3706123456789 CIDNR2 3706123456789 AAAAAAAA eight digit alphanumeric SMS password which is obligatory in the beginning of each SMS Manufacturer programmed password is AAAAAAAA User can change the password on his own desire see Ch 5 5 ALRNR1 ALRNRS user numbers CIDNRI1 CIDNR2 alarm monitoring station numbers Important a Nocharacters spaces can be used before the password b No spaces are allowed before and after the colon c Spaces must follow the password and each phone number d Itis recommended to enter user numbers with international code e g 123 It is not necessarily to send all user numbers e g in order to programme only the first user number send the following SMS AAAAAAAA ALRNR1 3706123456789 Receipt and decrypting of the SMS by GsmAlarm 500 is confirmed by blink of indicator MODE The phone which has sent the programming SMS immediately receives a confirming SMS with programmed numbers GsmAlarm 500 Software ver 1 04 13 PROGRAMMING In order to delete unnecessary num
46. ephone If the system receives a call coming not from the user s phone the call is immediately interrupted and the user is sent an SMS message specifying the caller s phone number The user is also informed by an SMS message about loss and restoration of AC mains power supply The system answers only to the numbers programmed If the system receives a call coming not from the user s phone the call is immediately interrupted and the user is sent SMS specifying the caller s phone number SMS messages are also sent to users in case of power loss and restoration The system has temperature measurement possibility Up to 6 temperature sensors can be connected to GsmAlarm 500 device If temperature exceeds or subsides programmed range system sends SMS to user s relevant programmable output can be activated deactivated 24 hour timer enables activation deactivation of programmable output arming or disarming receiving SMS messages with protected object state information on a desired time The system has capability to detect intentional jamming of GSM The siren is activated upon detection of the jamming signal and the user is informed thereof by an SMS message about it after clearing of GSM jamming signal The message indicates the jamming onset time GsmAlarm 500 parameters may be set via a computer using the GSM alarm configuration tool GAPROG The module is accessible via an USB port or over the internet through GPRS channel If a computer i
47. hods STAY SLEEP 17 5 3 2 Programming of Output C1 C4 K1 K2 and Common System Parameters Eg Ee ae ge A ge og eg Ly cl er A ane 18 5 3 2 1 Output C1 C4 K1 K2 Operating Mode c cc ccecceeseesseceeeeneeeseesseeeseeeseeeseeeseeeseees 19 5 3 2 2 Parameter E the Way User Is Informed About Arming Disarming 00 20 5 3 2 3 Parameter F System Response to Incoming Calls and Number Of Calls im Alarmi State sic siccccccsecissciediisinideaseeciotielasscedicdeblaiedacdivesssesecdlieberteeecenteettasieats 20 5 3 2 4 Parameter G SMS Delay Time in Case of Power Supply Failure eee 20 5 3 2 5 Parameter L SMS Structure and SMS Password Functionality ceeeeeeeees 21 5 3 3 Programming Partition Names y 2icetsacaiecesaniadnnneancsioneanacawosnincieeinconaiahaaraneinantainuanmadinaiens 21 5 3 4 Setting System COCK ceccccscsssssseseseesseescesseecseeeseesseeeseesseesseceseceseceseseeeceeeneeeeeeeeeeeaeeas 21 5 3 5 Programming 24 Hour Timer cccccccccccsscesseeseeeseeesceeseceseessecesecsseceseeeseceeeceeeenesseeeneeeseees 22 5 3 5 1 Timer TMS CUO ssion i E E E nepataas 23 5 4 Programming Description of Input Zone State oo cc ecccceceesscesceeseeeseceseeeseesseceseenseeseeeeeeeseees 23 5 5 Programming User Natties oranie tI le Ec E 24 5 6 Programming SMS Password cccccsscssscssscssseessesseseeeeseeseesseeeseesseesseeeseceseseseeesecseesseeseeesseeeseees 24 GsmAlarm 500 Softwa
48. icator that can be used as system status indicator If the system is controlled by an ON OFF switch the system is armed by opening the switch contacts and disarmed by closing the contacts Input circuits are connected according to corresponding diagram provided in Chapter 4 2 It is recommended to turn off zones that aren t used to change value of A parameter to A00 see Ch 5 3 1 1 A SIM card needed for GsmAlarm 500 operating you may acquire it from any GSM service provider Before inserting SIM card into GsmAlarm 500 SIM card slot set PIN code request off It can be performed simply inserting SIM card into any standard mobile phone and following certain phone user manual instructions After finishing installation insert SIM card into GsmAlarm 500 SIM card slot turn system power on then wait until LED NETWORK will start to flash and LED MODE will be constantly alight In case NETWORK is constantly alight check if SIM card s PIN code request is off and GSM antenna is connected GSM signal quality can be evaluated according the blinking frequency of NETWORK indicator Connection is very good if it blinks 5 times with short break after NETWORK indicator blinking fewer times indicates weaker connection System works in steady state if indicator blinks 3 5 times Position of GSM antenna might be changed in order to improve signal quality Perform system programming when the system is disarmed Pr
49. ikes In order to activate programmable output press the ARM key and enter an output control code If you want to deactivate the output press the OFF key and enter an output control code Programming of output control codes is described in Chapter 5 7 2 9 SYSTEM CONTROL USING iBUTTON ACCESS KEYS Touch shortly an iButton key to the contacts of the reader to activate or deactivate the protection mode and or activate programmable output The key is read in 1 2 seconds Completion of the key code capture is confirmed by a rapid blinking of the light indicator A key can be programmed for GsmAlarm 500 Software ver 1 04 43 SYSTEM CONTROL control of a single partition if the system is divided into 2 partitions or for control of the entire system Maximal number of keys 20 10 REMOTE ARMING amp DISARMING The system can be armed or disarmed remotely through a call or SMS message In order to arm or disarm the system through a call Call GsmAlarm 500 number Wait until system answers Enter 2 digit code using your phone keypad Press the key to activate the code You can use the following codes to arm or disarm your system 01 arms the whole system 00 disarms the whole system 83 arms the first partition 93 arms the second partition 82 arms the first partition STAY mode 92 arms the second partition STAY mode 81 arms the first partition SLEEP mode 91 arms the second partition S
50. ive users ALRNRI1 ALRNRS If system programmed to call and to send SMS messages at the end of the call cycle no user picks up the prone SMS message with name of triggered zone will be sent to all users If whichever user picks up and enters 2 digit code using his phone keypad codes are described in Chapter 12 SMS messages will not be sent to other users Example of the message user receives given bellow Entry Door ALARM 1 Motion OK 5 SMS message shows that entry door sensor is in alarm state opened and was triggered 1 time number in the brackets Motion detector is not in alarm state but was triggered 5 times Trigger counters are setted to zero values each time when the system is armed or disarmed While answering user hears what is happening in the premises and also can control system by by entering 2 digit codes using his phone keypad For example after entering code 99 the system cancels the call and user receives message informing about state of the all zones SYSTEM ARMED STAY MODE Entry Door ALARM 1 Motion OK 5 Windows ALARM 1 Fire OK 0 In the case of temperature zone activation user receives SMS message informing about temperature Temperature T 19C 12 POWER SUPPLY MONITORING The system GsmAlarm 500 will report every time mains 230V power supply fails or recovers In case of main power supply failure after the programmed delay time user ALRNRI receives following SMS message AC Main
51. ll lit constantly Enter a new 4 or 6 digit access code To delete an Access Code e Press the ENTER key e _ Enter your system installer code default code is 0000 or 000000 Select a user by entering a 3 digit user number e g 001 for user 1 or 020 for user 20 e Press and hold the SLEEP key until you hear the confirmation beep Table below describes which user will be informed about arming disarming the system with a short call or SMS message Address User or installer access code user number disarming the system 000 Imstaller AccessCode o O ALRNR3 ALRNR4 ALRNRS 006 6 User Access Code ALRNRI 007 7 User Access Code ALRNR2 008 8 User Access Code ALRNR3 009 9 User Access Code ALRNR4 010 10 User Access Code ALRNRS5 oll 11 User Access Code ALRNRI 012 12 User Access Code 13 User Access Code 14 User Access Code 15 User Access Code 15 User Access Code ALRNRI 17 User Access Code 18 User Access Code ALRNR3 19 User Access Code ALRNR4 20 User Access Code ALRNR5 GsmAlarm 500 Software ver 1 04 26 PROGRAMMING 5 7 2 USER ACCESS CODE FUNCTIONALITY After entering corresponding code user can arm or disarm the whole system or separate partitions activate or deactivate programmed outputs 1 user access code functionality 2 user access code functionality Parameter 11 user access code functionality 12 user access code functionality 13 user access code functionali
52. m Regular arming is possible only if all alarm zones are closed not triggered Constantly alight keypad keys indicate open zones key 1 zone Z1 key 10 zone Z10 Regular arming Close all protected doors and windows and stop movement in areas covered by motion detectors Check to see that the StayD Ready light is on all zones are closed The system cannot be armed unless the StayD light is off e Press the ARM key e Fnter a 4 digit or 6 digit user access code As each digit is entered the keypad buzzer will beep If the security code was entered incorrectly the sounder will beep steadily for 2 seconds If the code was entered correctly but the Ready light was not on the keypad will beep steadily for 2 seconds When the correct code is entered the ARM light will flash and the keypad buzzer will beep quickly Exit the premises through the designated exit entry door Exit delay time is indicated by short keypad beeps repeating each second At the end of the allowed exit time the keypad buzzer will beep quickly and the ARM light stays on constantly User receives confirmation short call or SMS message depends on system configuration see Ch 5 3 2 2 If system is divided into two partitions only one partition or both partitions at once can be armed when using particular access code Functionality of the access codes is described in Chapter 5 7 2 Regular arming can also be activated using 24 hour timer or One
53. mmed output modes C1 01 C2 05 C3 05 C4 02 The outputs can operate in an inverted mode i e the output circuit is disconnected upon reception of activation command and connected upon reception of deactivation command Address Parameter value Explanation of operation 320 01 Output C1 inverted Output C3 inverted 320 08 Output C4 K1 K2 inverted Manufacturer programmed value 04 Important To invert several outputs the total of numbers should be used Example To invert all outputs the number to be entered is 15 1 2 4 8 GsmAlarm 500 Software ver 1 04 30 PROGRAMMING 5 7 12 PARAMETER E THE WAY USER IS INFORMED ABOUT ARMING AND DISARMING Parameter E is described in detail in Chapter 5 3 2 2 Address 273 Parameter System parameter E Manufacturer programmed value 20 5 7 13 PARAMETER F SYSTEM RESPONSE TO INCOMING CALLS AND NUMBER OF CALLS TO USER Parameter F defines system response to incoming calls and number of calls to user in alarm state It is described in detail in Chapter 5 3 2 3 Address 274 Parameter System parameter F Manufacturer programmed value 31 5 7 14 PARAMETER G DALAY TIME OF REPORT SMS IN CASE OF POWER SUPPLY FAILURE Parameter G defines delay time of report SMS in case of power supply failure in minutes Possible values 00 99 minutes This parameter is described in Chapter 5 3 2 4 in more detail
54. nd STAY will lit constantly Enter 6 digit event instruction and event time First two digits event instruction where following four timer activation time E g for output C2 to be activated at 12 15 begin entering address 407 event TMRO1 then enter 22 12 15 22 output C2 activation code 12 15 activation time Addr Event Addr Event Addr Event Addr Event No No No TMR06 416 TMRI6 TMR07 417 TMR17 TMR08 418 TMRI8 404 TMRO04 409 TMRO9 414 TMRI14 419 TMRI9 405 TMROS 410 TMRIO 415 TMRIS5 420 TMR20 GsmAlarm 500 Software ver 1 04 33 PROGRAMMING 5 7 24 PROGRAMMING CONTACT ID USER ACCOUNT NUMBER Four digit user account number is provided by security service that protects object This parameter is described in Chapter 7 in more detail 0000 9999 Manufacturer programmed Contact ID user account number 0000 5 7 25 TEMPERATURE CORRECTION The measured temperature may be corrected by changing the address 140 parameter The number 20 corresponds to the null correction The temperature value increases and decreases together with this number The step of correction 0 3 C The correction applies to all inputs collectively Measured temperatures of individual inputs may not be corrected 5 8 PROGRAMMING iBUTTON KEYS It is recommended to execute programming and setup of iButton keys via a computer using the GSM alarm configuration tool G
55. ntrolled by a iButton DALLAS keys K02 the system is controlled by an ON OFF switch L32 SMS structure and SMS password functionality P00 partitioning P00 partitions do not exist P01 system is divided into two partitions T20 entry delay time Possible values 00 99 seconds After correction of the parameters SMS message is sent back to GsmAlarm 500 GsmAlarm 500 Software ver 1 04 18 PROGRAMMING 5 3 2 1 OUTPUT C1 C4 K1 K2 OPERATING MODE Addr 32 1 325 Output Explanation of operating mode Output controlled by DTMF or SMS instructions If zero operating time is programmed T00 output is activated deactivated and remains in the same state after receiving DTMF or SMS instruction If not zero operating time is programmed after receiving DTMF or SMS instruction output is activated it deactivates automatically after expiration of the programmed time Output is activated when system is armed Open contact when system is disarmed Control by short call without number recognition function Output is activated with a call from any number If zero operating time is programmed 700 output state changes after a call and remains unchanged till the next short call If not zero operating time is programmed after receiving short call instruction output is activated it deactivates automatically after expiration of the programmed period Control by short call with number recognition function gate control mode This
56. otected zones must be closed indicator MODE constantly alight Detailed programming description can be read in Chapter 5 GsmAlarm 500 Software ver 1 04 INSTALLATION 4 2 WIRING DIAGRAMS 4 2 1 SYSTEM WITH KEYPAD ACCESS CONTROL DOO Oe Oe GND Z1 Z2 Z3 Z4 Z5 Z6 GND GR YL AUX C1 C2 C3 KI K2 AC a o GREEN BLACK Keypad zone 1 Additional relays for extra commutated devices Power supply transformer AC 16 24V 1 2 A AC 230V 2 wire smoke detector E318 2LED Power supply for motion or fire detectors 4 2 2 SYSTEM WITH iBUTTON ACCESS CONTROL DOOD OOO VO OOO OOF GND Z1 Z2 Z3 Z4 Z5 Z6 GND GR YL AUX C1 C2 C3 KI K2 e Power supply i transformer System status indicator l y AC 16 24V AC 230V DS9092LED i 2 wire smoke detector iButton key E318 2LED reader Power supply for motion or fire detectors Switch ON OFF Additional if iButton key is not used relay GsmAlarm 500 Software ver 1 04 INSTALLATION 4 2 3 WAYS TO CONNECT ALARM ZONES GND Z GND Z GND Z NO NC NC ALY A2Y A3Y no EOL with one EOL resistor A3Y GND Z Z07 Z15 Z01 Z06 with two EOL resistors ATZ mode A4Y NC norm
57. r ALRNR1 System is calling 2 2 Only user ALRNR2 Siren and calling 3 3 Only user ALRNR3 System is sending SMS message 4 4 Only user ALRNR4 Siren and SMS 5 5 Only user ALRNRS Calling and SMS 6 6 Users ALRNR1 and ALRNR2 Siren calling and SMS 7 7 Users ALRNR1 ALRNR2 and ALRNR3 8 Users ALRNR1 ALRNR2 ALRNR3 and ALRNR4 9 All ALRNR1 ALRNRS but not the alarm monitoring station Important alarm monitoring station is informed when data transfer to monitoring station is turned on see Ch 7 3 number X is higher than 0 and number Y isn t equal to 9 5 3 1 3 PARAMETER P PARTITION ASSIGNMENT AND PARTIAL ARM METHODS STAY SLEEP Addr 281 296 Partition assignment PXY Partial arming mode STAY and SLEEP In SLEEP and STAY modes zone not active Zone assigned to the first partition 1 1 Zone is active in STAY mode Zone assigned to the second partition 2 2 Zone is active in SLEEP mode Zone assigned to both partitions 3 3 Zone is active in SLEEP and STAY modes Manufacturer programmed value P10 GsmAlarm 500 Software ver 1 04 17 PROGRAMMING 5 3 2 PROGRAMMING OUTPUTS C1 C4 K1 K2 AND COMMON SYSTEM PARAMETERS R F G H T3 K D Pr ET In order to receive SMS with output and common system parameters send GsmAlarm 500 the following SMS AAAAAAAA CPARAM Receiving the message is confirmed by blinking of indi
58. r programmed value 04 5 7 20 EXIT DELAY AUDIBLE INDICATION When a close code is entered delay time count can be indicated by short keypad beeps repeating each second Address Parameter value Explanation 235 Audible indication OFF Audible indication ON Manufacturer programmed value 01 5 7 21 ASSIGNING KEYPAD ZONES Paradox keypads have zone inputs to which devices such as door contacts can be connected See Ch 4 2 1 for wiring information Once the keypad zones are installed assign the zone number to keypad zone e Press the ENTER key e _ Enter your system installer code e Press and hold the O key until 3 short beeps are heard lights ARM and STAY are on constantly GsmAlarm 500 Software ver 1 04 32 PROGRAMMING If K636 K10V or K10H keypad is used keypad zone is assigned after pressing corresponding key from to 10 Turned on key is showing the zone that is assigned Zone assigning is confirmed by pressing ENTER key Keypad zone can be deleted by pressing the CLEAR key If K32 or K32LCD keypad is used keypad zone is selected by pressing two digits For example if you want to assign zone 16 to the keypad zone press 1 and 6 If you want to assign zone 3 press 0 and 3 Keypad zone is deleted by pressing CLEAR and ENTER keys Important after assigning zone to the keypad the corresponding input zone won t be operating on the GsmAlarm 500 board 5 7 22 SETTING SYSTEM CLOCK
59. re seen in the SMS after alarm triggering User can change the name of zone under his own discretion Maximum number of name characters 16 5 3 1 1 PARAMETER A INPUT ZONE TRIGGERING CONDITIONS Addr 201 216 Input zone triggering conditions AXY Input zone operating mode Input disabled 0 0 Delay zone 2 Alarm is activated if contacts are 24H zone 3 closed NO see Ch 4 2 Alarm is activated if contacts are 2 2 Fire zone opened NC see Ch 4 2 EOL mode load resistor is required 3 3 ON OFF zone Y see Ch 4 2 ATZ advanced technology zone Follow zone P 2 2 kQ and 4 7 kQ load resistors are 4 4 required see Ch 4 2 2 wire smoke detector connected to Dual activation delay zone 7 the PGM output C3 D 5 5 Dual activation 24 hour zone 7 Force arm Delay zone Temperature measurement mode Force arm Follow zone Force Alarm is activated if measured 8 8 arming allows to arm the system temperature overcomes programmed without waiting for all zones to temperature T close Temperature measurement mode Alarm is activated if measured 9 temperature is lower than programmed temperature T 1 Only zone Z7 can operate in this mode PGM output C3 must operate in mode M01T05 inverted 2 Delay zone After relevant zone is being triggered the system will generate alarm only in armed mode after expiration of the programmed entry delay time 3 24 hour zone Af
60. re ver 1 04 TABLE OF CONTENS 5 7 Programming the System using the Keypad cccccccscccsseeceseeceseeeeeeeeeseeesseeesseeeeseeenees 25 5 7 1 Programming Access Codes ccccccccsscsssesseesseeseeeseceseeeecesecsseceseceseceseceseessecnssenseseeeeseeeneees 26 5 7 2 User Access Code Functionality c cccc h0c3cidesei distinc iet it ialiediia linden 27 De 13s Exit Delay TIME ccena a vesacdes ts dcastesaz deicaadedastscidvacematace ETA E aeoesvsieons 27 5 7 4 Parameter T Entry Delay Time or Triggering Temperature ccccccecceseeseesseeseeeeees 28 5 7 5 Parameter A Input Triggering Conditions sisiesji wncveinacesuievisstaincsdetentavanvieilaacreciembunduets 28 5 7 6 Parameter M System State after Input Triggering ccc ceccssceeteceecseeeseeeseeeseeeseees 28 5 7 7 Parameter P Partitions Assignment and Partial Arm Methods ceseseseeeeeeeees 29 5 7 8 Parameter T Pulse counting Mode ccccccsscessessseessceseceseeeseceseesseceseeeecseeeeseeesseeeseees 29 Be ae OMS Rens TIME siiis doroin kena ren E N IE aA EEEE AEE EEE EEEE ERN EEAS 29 5 7 10 Operating Time of Outputs C1 C4 and BELL oases cssivscdsosvessnenlassviacs redaseasnevaonteanassivesnens 30 5 7 11 Operating Mode of Outputs C1 C4 and BELL o ee e ee eccecceseeeeeeseeeeeeeeecneeenseseeeeseeeseees 30 5 7 12 Parameter E The Way User Is Informed About Arming Disarming eeeeeee 31 5 7 13 Parameter
61. rough DTMF tones GsmAlarm 500 has 3 4 if siren is not used programmable outputs intended for remote control of different devices User can turn on off heating ventilation or lighting systems etc by using his mobile phone just by typing a 2 digit code or sending SMS to the control device Device works perfect for remote control of automated gates fences and electromagnetic door locks In order to open the gate user calls GsmAlarm 500 number Then GsmAlarm 500 checks the caller s number in the list of programmed user numbers and in the case of positive find switches on the gate control device and cancels the call automatically 250 users are able to control the gate Up to 4 keypads can be connected to GsmAlarm 500 By using the keypad users can arm or disarm the system and configure system parameters Following keypad LED indicators you can determine protected unit state system mode etc The system is controlled by iButton also known as DALLAS keys Several control functions can be assigned to each key Example a user can activate a protection mode and a controllable output by touching the contact with the key A user name can be assigned to each key as well as to a keypad code that will be indicated in SMS messages Up to 20 iButton keys can be programmed If keypad or iButton keys are not used the system may be armed and disarmed by a simple switch or a short free call The installation is controlled exclusively from the user tel
62. s fault Battery voltage 12 5V Signal strength 100 In case of recovery of power supply after one minute user ALRNR receives following SMS message AC Mains OK Battery voltage 13 7V Signal strength 100 If data transfer to monitoring station option is on messages at first are sent to alarm monitoring station and then to user ALRNR1 The system also will report about the fault of backup battery or the backup battery is running out of power GsmAlarm 500 Software ver 1 04 SYSTEM CONTROL 13 GSM JAMMING DETECTION The system has capability to detect intentional jamming of GSM If the detection function is on see Ch 5 3 2 or 5 7 16 the siren is activated upon detection of the jamming signal and the user is informed thereof by an SMS message about it after clearing of GSM jamming signal Siren operates with interruptions The message indicates the jamming onset time GSM Jamming detected Time 08 55 GsmAlarm 500 Software ver 1 04 46 SYSTEM CONTROL 14 SYSTEM CONTROL BY DTMF AND SMS COMMANDS In the speech mode user can control the system after having entered relevant code from his phone keypad 2 digit command is entered by pressing the key If the instruction is completed user hears three tone confirmation signals Speech mode can be activated in two ways user answers when GsmAlarm 500 calls or user calls and waits for GsmAlarm 500 to answer 3 4 call signals The control commands also may be
63. s isinsi iie EE EEE ban tn gdp Dube sll dread E aed aR a Apa 2 1 3 EEA sn e N EEA EE AO EEE E E aeaa 3 2 Connector and LED Functionality 0 0 00 ccc eccecececeeseeeseeseeeseeeseceaeeeaeceaeceneceaeseaeeeneceeecneeeeeeas 4 2 1 Zone Inp t terminals ZL GO AG ossido iiri TEE Ea E AEE i 4 2 2 Keypad Connection Terminals GR and Vl xiwcstennsaincintexiansncammmotenconarountuciaamenccebetinaawnwent 4 2 3 Auxiliary Power Termmal AUX onanie ea A ee 5 2 4 Programmable Output Terminals C1 C2 and C3 occecccccccccsccesesssceseeeseeeseeeseceseesseeseeeseeenseeeeeas 5 2 5 BELL SIREN Connection Terminals K1 K2 wc ccccssssscccceeesssseseccecsssseesecseessnseseseeesaes 5 Dee AC P w r Terminals orsoni ernan tuscan siine Ae E Ea Ea EEE Ea RE TEE Soi E E EE NE 5 27 BAF COMME CON ls isic ece a a E E E E EE E RA ER E ee 5 2 8 External Microphone Connector silo scssdssioaseasaluseriuasenghinciouseonasepedelisesesaiciouidasnedeebeuseeploniempaadsines 5 2 9 RESET Butto ceccnsisicsnineeeii na E E EEA E ai 5 3 LED Wii ators necces asin tvesieasens balssntnasieetesezes tas naiedd aeadasiee dealaesinden devon adsiaeiceees 6 3 1 NETWORK GSM Module State and Signal Strength indicator ceeeeeseeseeseeeeeeeeeeeeees 6 3 2 MODE Alarm System Status Indicator jays cascrsiatininnebe otoactoamaialoasralnniercieapenen madison 6 4 Msta lation neniani a E EA E EE E E 7 4 1 General Installation Instructions ccccescsssessessseesceesceseeeeseeeseessecnsecesecssece
64. s unavailable the system is set up by a keypad or SMS messages GsmAlarm 500 Software ver 1 04 TERMINAL CONNECTIONS 2 CONNECTOR AND LED FUNCTIONALITY RESERVE GSM ANTENNA SYSTEM STATUS BATTERY CONNECTOR LED INDICATORS Jb CONNECTOR SMA NETW MODE O GSM MODULE M M MICROPHONE CONNECTOR C4 Teal O H mel GND Z1 Z2 Z3 Z4 Z5 Z6 GND GR YL AUXC1 C2 C3 KI K2 01010101010101 01010101 010101010010 Connection terminals and LED indicators 2 1 ZONE INPUT TERMINALS Zi to Z6 Inputs Z1 Z6 are used to connect alarm detectors or temperature sensors KTY81 110 PHILIPS Processor The zones are designed to work with End of Line EOL resistors of 2 2 KQ and 4 7 KQ in ATZ mode see Ch 4 2 3 The system becomes triggered both when the input circuit is broken as well as when it is short circuited The inputs can operate in a non EOL mode see Ch 4 2 3 In this case EOL resistor in not required The system is triggered after breaking or short circuiting of the input circuit depending on the programmed active level Equivalent diagram of zone input 2 2 KEYPAD CONNECTION TERMINALS GR and YL Use GR YL GND and AUX terminals to connect PARADOX K636 K10V H MG10LEDV H K32 MG32LED or K32LCD MG32LCD keypad These terminals can also be used for connection of the iButton key reader GsmAlarm 500 Software ver 1 04 TERMINAL CONNECTIONS 2 3 AUXILIARY POWER T
65. seceseseeeseeeseeeesseegeens 7 4 2 Wiring Diatas igesari Ee A ad sno spur E ns aaneenasnaalebuie 9 4 2 1 System with keypad access control cas cssseuiaiiorinaedaueiceuadancsidviniacenduastrsiastcos side usucadebeBainatetites 9 4 2 2 System with iButton access COMtIOL ec ccecceccesseesseeseceseeescessecesecsseeeeceecseesseeeeeeseesseesseeeas 9 4 2 3 Ways to Connect alarm ZONES coe ann E E A ce 10 4 3 Connection of Temperature Sensors ccccccsscssssessesseesseeeeecsceesceeseceseceseeeseceseceseessecnseeeseeeseesees 11 S Programming sieer niiin i R E EAE EEEN EEE 12 5 1 General Programming Instructions cccceccsssesseeseeeseeeceeseeeseeescesseceseceseceseeeseceseesseseseenseessees 12 5 2 User and Alarm Monitoring Station numbers ccccceesceesseessesseeeseceseceseeseeeeeecseeeeeseeeneeeseees 12 5 2 1 Programming with Standard Mobile Phone ccccccecscessescceseeeseeseeeeeeeeecsseeseeseeeeseeeseees 12 5 2 2 Programming with SMS e onasnecierin iiie R KATERE E E A n 13 5 3 Programming System Parameters with SMS ooo cccccecccsecsseeceseeeeseeeeseeesseeenseeesseeenees 15 5 3 1 TOPE AUNT 7 INC 8 inserarea r an aaan E ea Nia e a Ea aaa 15 5 3 1 1 Parameter A Input Triggering Conditions cccecceeseesseeseeeeeeeeeseeeseeeeeeeseeeseees 16 5 3 1 2 Parameter M System State after Input Triggering ceecceeseeseeeseeeseeeseeeseees 17 5 3 1 3 Parameter P Partition Assignment and Partial Arm Met
66. sent back to GsmAlarm 500 Maximum number of the name s characters is 16 5 3 4 SETTING SYSTEM CLOCK System s clock should be set only if timer function is used In order to set system clock time E g 12 45 following SMS must be sent to GsmAlarm 500 AAAAAAAA SCLOCK 12 45 10 01 15 AAAAAAAA password SCLOCK time set instruction 12 45 time 12 45 10 01 15 date year month day GsmA larm 500 Software ver 1 04 21 PROGRAMMING Check up of programmed system time can be preformed by sending following SMS to GsmAlarm 500 AAAAAAAA SCLOCK GsmAlarm 500 sends back SMS with programmed system time to the specific user 5 3 5 PROGRAMMING 24 HOUR TIMER Timer function can activate or deactivate the programmable output arm or disarm the system send SMS message etc on a desired time It is recommended to receive SMS message with programmed timer parameters To do that following SMS message must be sent to GsmAlarm 500 AAAAAAAA STIMER GsmAlarm 500 sends back 2 messages with current timer parameters to user AAAAAAAA TMRO1 00 00 00 TMRO2 00 00 00 TMRO3 00 00 00 TMR04 00 00 00 TMR05 00 00 00 TMR06 00 00 00 TMR07 00 00 00 TMR08 00 00 00 TMR09 00 00 00 TMR10 00 00 00 AAAAAAAAA password TMR0O1 TMR10 number of timer event 20 independent timer events can be programmed 00 timer instruction defining which function should be performed in programmed time Please read detailed description of timer in
67. stem can be performed only if person possess basic knowledge in electricity and electronics otherwise device might be irrecoverably damaged System should be assembled in metal housing 7TRP20 as recommended GSM antenna Antenna cable Metal housing 7 TRP20 GSM antenna gt 6cm connector NETW MODE E usB GSM MODULE M M MICROPHONE CONNECTOR Board GSMA 500 fixture holes Toad 4x3 5 mm f on Aj o GND ZI Z2 Z3 Z4 Z5 Z6 GND GR YL AUX Cl C2 C3 KI K2 AC OWDOODDODODODODOOGOOOO HOLE FOR CABLES AC 230V AC 18V POWER SUPPLY TRANSFORMER BACKUP Housing BATTERY TRP 20 01 fixture holes 4x5mm AC 12V 1 3Ah CT1 3 12 2 TO 16A LSTEN 60950 Recommended layout of system elements in 7 TRP20 type housing Use double isolated cable 3x0 75 mm for 230V power supply Circuit breaker or other surge protection device should be installed in the 230V power line GsmAlarm 500 Software ver 1 04 INSTALLATION Antenna is fixed on the top of outer side of metal housing It is recommended to use standard motion SRP 300 and fire EA318 4 sensors in alarm system Use standard 6 8 wired single core cable designed for installation of alarm systems Siren DC12V 500mA S 108 is recommended for sound alarm use double isolated cable 2x0 75 mm to connect it to the system Backup battery must be PB acid CT1 2 12 It is re
68. structions in Ch 5 3 5 1 00 00 timer activation time Renewed SMS message has to be sent to GsmAlarm 500 User receives SMS message with newly programmed parameters after Examples for programming For the system to activate PGM output C2 on 12 30 deactivate on 13 00 and to send SMS message informing about the state of outputs on 13 01 following SMS has to be sent to GsmAlarm 500 AAAAAAAA TMR01 22 12 30 TMRO2 20 13 00 TMR03 77 13 01 GsmAlarm 500 Software ver 1 04 22 PROGRAMMING 5 3 5 1 TIMER INSTRUCTIONS Addr 401 420 00 Timer eventis not active S O 10 Deactivates output C1 40 Deactivates output C4 K1 K2 80 Disarms the first partition S O Arms the first partition SLEEP mode Arms the first partition quality and power supply voltage OO P eea E Mining Salon vis C protocol see Ch 7 3 Disarms the second partition Arms the second partition STAY mode Arms the second partition SLEEP mode Arms the second partition 99 Requests to send SMS message with information about state of protected zones Note Command 89 is sending message to alarm monitoring station only 5 4 PROGRAMMING DESCRIPTION OF INPUT ZONE STATE In order to program description of input zone state e g ALARM when zone is open or OK when zone is closed following message is sent to GsmAlarm 500 AAAAAAAA ZOPTXT ALARM ZCLTXT OK ZOPTXT and ZCLTXT programming commands ALARM O
69. ter relevant zone is being triggered the system generates alarm in armed or disarmed mode siren operates constantly and delay time is ignored 4 Fire zone The system generates alarm in armed or disarmed mode Siren operates with interruptions 5 ON OFF zone Mode designated to arm or disarm the system if keypad is not used GsmAlarm 500 Software ver 1 04 16 PROGRAMMING 6 Follow zone After violation of this zone alarm goes on immediately if other zone with delay isn t violated If firstly zone with delay is violated for example doors are opened follow zone receives delay time of earlier violated zone It is recommended to apply this mode to motion sensor zone if sensor is installed before the entry doors to the room 7 System is responding both to zone activation and restoring in dual activation mode After activation of the zone system is responding in the same way as in mode 0 and 1 After zone recovery when zone comes back to the initial state system doesn t call and doesn t turn on the siren Users receive only SMS message if SMS message sending is activated see Chapter 5 3 1 2 5 3 1 2 PARAMETER M SYSTEM STATE AFTER INPUT TRIGGERING Addr 241 256 Type of alarm after input triggering MxY Users getting information about zone violation All functions described below are deactivated All ALRNR1 ALRNR5 Only siren is operating 1 1 Only use
70. this case Any name can be ascribed to user Output operating mode has to be M04 or M05 see Chapter 5 3 2 1 5 2 1 PROGRAMMING WITH STANDARD MOBILE PHONE Insert SIM card into a standard mobile phone Enter user name into SIM card number book using capital letters e g ALRNR and corresponding phone number We recommend enter the number with international code E g 370 GsmAlarm 500 Software ver 1 04 12 PROGRAMMING If GsmAlarm 500 is used for gate control number of extra user numbers can be as large as fits into the SIM card up to 250 Any name can be ascribed to user When programming alarm monitoring station number you must use capital letters and enter name CIDNR1 CIDNR2 and number numbers of alarm monitoring station Important It s important to note that while programming SIM card memory should be active not phone memory Otherwise the user number will be recorded in the mobile phone memory used for programming and the SIM card will remain empty After having programmed all user numbers it is recommended to check whether SMS service center number is programmed Simplest way to check send any SMS from the phone used for programming If it is sent successfully we can be sure that SMS centre number has been programmed correctly Otherwise programme SMS center number following the mobile phone s user manual SMS center number can be learnt from GSM service provider After completion of programming and ch
71. transferred by SMS Insert password in the beginning then type the command E g in order to switch on output C to switch off output C2 to switch on BELL and to receive a SMS with information on the status of the PGM outputs send the following SMS AAAAAAAA 11 20 77 or 11 20 77 if SMS password is deactivated DTMF or SMS Code Function code 44 Activates output C4 K1 K2 Deactivates output C4 K1 K2 Requests to send SMS about state of the system outputs Disarms the first partition 81 Arms the first partition STAY mode 82 Arms the first partition SLEEP mode 83 Arms the first partition 88 Requests to send SMS with information about GSM signal strength and power supply voltage Disarms the second partition 91 Arms the second partition STAY mode 92 Arms the second partition SLEEP mode 93 Arms the second partition Requests to send SMS with temperature values only Requests to send SMS about state of the system and protected zones 0 Ol 16 Temporary disconnects of the zone turning on BYPASS mode 0 Turns off BYPASS mode of the all zones Activates iButton key programming mode 70 Deactivates iButton key programming mode SMS and DTMF instructions It is possible temporarily to turn off chosen zone by commands 0 16 for example in the case of sensor fault if system is constantly sending wrong alarm messages In order to turn off zone Z1 GsmAl
72. ty 14 user access code functionality 04 04 04 035 5 user access code functionality 045 15 user access code functionality 04 04 04 16 user access code functionality 17 user access code functionality 18 user access code functionality i 19 user access code functionality 20 user access code functionality 9 user access code functionality 10 user access code functionality Parameter value Access Code Functionality 00 Arms or disarms the whole system 01 Arms or disarms the first partition Arms or disarms the second partition Activates or deactivates the output C1 Activates or deactivates the output C2 30 Activates or deactivates the output C3 40 Activates or deactivates the output C4 K1 K2 Manufacturer programmed value 00 Output is switched on after pressing ARM key and entering corresponding code Output is switched off after pressing OFF key and entering corresponding code 5 7 3 EXIT DELAY TIME The closing code transmission takes place after the exit delay time Therefore if the system is armed and disarmed before the expiry of the exit time no transmission will take place Possible values 00 99 seconds Address Parameter 100 Exit delay time Manufacturer programmed exit delay time 20 seconds GsmAlarm 500 Software ver 1 04 27 PROGRAMMING 5 7 4 PARAMETER T ENTRY DELAY TIME OR TRIGGERING TEMPERATURE After the e
73. umbers of users to GsmAlarm 500 see Ch 5 2 2 Second group parameters defining system operating algorithms names of protected zones and programmable outputs These parameters are stored in the memory block of GsmAlarm 500 device The parameters of the system can be programmed by sending SMS message see Ch 5 3 or by using Paradox keypad see Ch 5 7 It is recommended to change the SMS password at the end of programming see Ch 5 6 5 2 USER AND ALARM MONITORING STATION NUMBERS If GsmAlarm 500 is used for protection five user numbers can be programmed ALRNR1 ALRNR2 ALRNR3 ALRNR4 and ALRNR5 and two alarm monitoring station numbers can also be programmed CIDNR1 CIDNR2 Users can arm disarm the system calls will be directed and SMS messages will be sent to these users If only one user exists he must be programmed under ALRNR1 GsmAlarm 500 will send SMS messages to this specific user in case of main power supply loss or if an unknown number calls the system If armed mode is turned on or off with the single touch of the keypad or by turning the switch ON OFF if the keypad is not used control dials and SMS messages are also directed to the first user Other four user numbers are not obligatory In case GsmAlarm 500 is used only for gate control it is not necessary to programme ALRNRI ALRNRS Up to 250 user numbers with the possibility to control the outputs C C2 C3 C4 and BELL with a short call can be programmed in
74. xit delay has expired an open on the zone will cause the entry delay time to start During the entry time the keypad buzzer will sound steady If the panel is disarmed before the entry time expires no alarm will be generated Possible entry delay time values 0 99 seconds If zone operates in temperature measurement mode value of T parameter corresponds to triggering alarm activation temperature Possible temperature values 0 99 C Parameter Zone Z1 T parameter Zone Z9 T parameter 102 Zone Z2 T parameter 110 Zone Z10 T parameter Zone Z11 T parameter Zone Z12 T parameter Zone Z13 T parameter Zone Z14 T parameter Zone Z15 T parameter Zone Z8 T parameter Manufacturer programmed time for zone Z1 20 seconds zones Z2 Z15 00 seconds 5 7 5 PARAMETER A INPUT TRIGGERING CONDITIONS Parameter A defines system s input operating modes and is described in detail in Chapter 5 3 1 1 Parameter Zone Z1 A parameter Zone Z9 A parameter Zone Z2 A parameter Zone Z10 A parameter Zone Z3 A parameter Zone Z11 A parameter Zone Z4 A parameter Zone Z12 A parameter Zone Z5 A parameter Zone Z13 A parameter Zone Z14 A parameter Zone Z15 A parameter Zone Z8 A parameter Manufacturer programmed values for zones Z1 Z6 30 zone Z7 52 and zones Z8 Z15 00 5 7 6 PARAMETER M SYSTEM STATE AF
75. ystem is in armed mode and temperature reaches programmed value user receives SMS message siren will not turn on and system will not dial If two triggering temperatures are required an extended zone Z7 Z15 may be assigned to the main temperature zone Z1 Z6 The A8Y mode or A9Y mode should be activated for the ancillary temperature zone see Ch 5 3 1 1 The extended temperature zone operates according to the temperature measured by the main temperature zone The number of the main temperature zones should correspond to the number of the extended temperature zones GsmAlarm 500 Software ver 1 04 11 PROGRAMMING 5 PROGRAMMING 5 1 GENERAL PROGRAMMING INSTRUCTIONS It is recommended to perform the system setup and tuning by a computer via USB port using the GSM alarm configuration tool GAPROG The GsmAlarm 500 main board is connected to the computer with a standard USB A B cable The configuration tool is downloadable from the website of the manufacturer www eltech It The GSM alarm configuration tool GAPROG allows setting up of the system over the internet see Ch 5 9 If a computer is unavailable the system is set up by a keypad or SMS messages GsmAlarm 500 parameters can be divided into two groups First group user phone numbers which are stored in SIM card memory User phone numbers can be programmed by using standard mobile phone of any type see Ch 5 2 1 or remotely sending SMS message with the phone n

GsmAlarm-500 (V1.04)

Contents

Download Pdf Manuals

Related Search

Related Contents