U5303A PCIe High-speed Digitizer - Startup Guide
Contents
1. Step 4 Install Modules Closely follow the startup process flow in this document Deviating from the sequence can cause unpredictable system behavior damage your system and may cause personal injury Keysight U5303A Startup Guide 9 Step 1 Unpack and Inspect the Module step 1 Unpack and Inspect the Module The module is shipped in materials which prevent damage from static The module should only be removed from the packaging in an anti static area ensuring that correct anti static precautions are taken Store all modules in anti static envelopes when not in use Electrostatic Discharge ESD Precautions Building Ground 1 Meg Ohm Resistor P m a a e ee ha Z m e o a e E E ee a E a eee O e e net see io Se Electrostatic discharge ESD can damage or destroy electronic components Use a Static safe work station to perform all work on electronic assemblies The figure left shows a Static safe work station using two types of ESD protection conductive table mat and wrist strap combination and conductive floor mat and heel strap combination Both types when used together provide a significant level of ESD protection Of the two only the table mat and wrist strap combination provides adequate ESD protection when used alone To ensure user Safety the static satfe accessories must provide at least 1 MQ of isolation from ground DO NOT use these techniques f2. U5303A PCle High Speed Digitizer Introduction U5303A PCle High Speed Digitizer Introduction The scope of this Startup Guide is to detail the processes of receiving and Installing the Keysight U5303A PCle High Speed Digitizer installing the required software and verifying basic module operation If you have any questions after reviewing this information please contact your local Keysight representative or contact us through our website at www keysight com Tind contactus Related Documentation This Startup Guide and the documentation listed below are contained on the CD supplied with your product and at www keysight co m find U 5303A overview amp Options amp Document Library Select Document Library gt Manuals a U5303A User Manual Refine the List 1 16 of 16 Help systems for the Keysight device oo drivers IVI C and VI COM and LabVIEW immer a G Product specifications Datasheet Keysight U5303A Startup Guide U53038A PCle High Speed Digitizer Introduction Follow the Startup Sequence This Start Up Guide Is intended to lead the user through the four steps of product installation as Summarized in the diagram below An optional fifth step shows how to perform an operational verification of the Us303A PCle High Speed Digitizer Step 1 Unpack and Inspect Step 2 Verify Shipment Step 3 Install Drivers and Software we J ee Ai i perem J Ww KEYSIGHT TECHNOLOGIES J NS ALOU S
3. EXPRESS OR IMPLIED WITH REGARD TO THIS MANUAL AND ANY INFORMATION CONTAINED HEREIN INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE KEYSIGHT SHALL NOT BE LIABLE FOR ERRORS OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE FURNISHING USE OR PERFORMANCE OF THIS DOCUMENT OR OF ANY INFORMATION CONTAINED HEREIN SHOULD KEYSIGHT AND THE USER HAVE A SEPARATE WRITTEN AGREEMENT WITH WARRANTY TERMS COVERING THE MATERIAL IN THIS DOCUMENT THAT CONFLICT WITH THESE TERMS THE WARRANTY TERMS IN THE SEPARATE AGREEMENT SHALL CONTROL KEYSIGHT TECHNOLOGIES DOES NOT WARRANT THIRD PARTY SYSTEM LEVEL COMBINATION OF CHASSIS CONTROLLERS MODULES ETC PERFORMANCE SAFETY OR REGULATORY COMPLIANCE UNLESS SPECIFICALLY STATED Technology Licenses The hardware and or software described in this document are furnished under a license and may be used or copied only in accordance with the terms of such license U S Government Rights The Software is commercial computer software as defined by Federal Acquisition Regulation FAR 2 101 Pursuant to FAR 12 212 and 27 405 3 and Department of Defense FAR Supplement DFARS 227 7202 the U S government acquires commercial computer software under the same terms by which the software Is customarily provided to the public Accordingly Keysight provides the Software to U S government customers under
4. 06 MD1 Soft Front Panel Help System Help File User Manual 1 Access to all Documentation Documentation Map KEYSIGHT TECHNOLOGIES M9703A AXle 12 bit High Speed Digitizer Widebar Digital Receiver Sold By Keysg Usually aa re in B weeks Startup Guide e Unpack product Keysight e Verify shipment e Install software e Install amp connect hardware e Verify operation e Troubleshooting Keysight High Speed Digitizer Wee Ween Visual Studio Be s we a Soa S ep O ba ee oe Peo ie O 2 P come tarau Fai suis Candi tiani o Modiga D onasan Paida eaei n Ban See toate Keysight U5303A Startup Guide User Manual High Speed Digitizer In depth information and reference material specific to your digitizer product Datasheet e Product description e Technical specifications Colpito Al F Code A AgM9392Measurements GetPowerSpectrum Method nace Sahoo ease mers Returns the spectrum os computed Dy an FFT of the rmessurement cots VI COM and IVI C driver programmer s reference n dete is megritude in d be ficats The FFT resus sre swaoped s9 OC a MIR E 1 The number of retum semsies is fiSee N e igi Aaya Iyer Assembly ADIOMLAZNG ISS moroa n Agilent AOMIT3 Letersg dl Syntax Visual Basic Palic Sub GecPowerSpeccram _ DyVel Fr Sire As Integer _ Oyfet NegsitudeArray As Sizgie
5. 2533 a Replace any covers and switch on the PC Check the module front panel indic ators a few seconds after the boot process both the Status and DPU LEDs should be green Keysight U5303A Startup Guide Step 4 Install the Module When disconnecting the auxiliary power cable it is important to push it away from the PCB side of the U5303A in order to disengage the friction lock Failure to do this could cause the module side of the connector to be withdrawn at the same time thus damaging it _ am Note that the U5303A is optionally supplied with a card retainer included if ordered as U5303A 001 or available separately by ordering stand alone extender please contact support for the reference which is able to pick up on slots at the end the full length PCle slot and provide additional support for the module Use of this card retainer is highly recommended in particular when the PC motherboard is oriented vertically However if your PC hardware does not provide end slots the card retainer may be removed from the module It is also possible to reverse the orientation of the fan assembly in the case that two modules must be placed in adjacent slots or other PC hardware obstructs the fitting These three procedures are detailed below Fitting the module with the optional card retainer into your ae 1 Loosen but do not remove the screw A holding the rear card retainer and Slide it towards the fans 2 I
6. Press any key to start the test The screen capture below shows the result of a successful verification Keysight U5303A Startup Guide pDriver identifier AgMD2 Driver revision 1 6 182 1 Fundamental 1 6 2329 1 sun 6078 M gt Driver vendor Keysight Technologies ii description IVI Driver for AgMD2 family of digitizers Compiled for 64 b it gt Verify resource PRI11 6 6 INSTR Selection Cor CENTER to exit gt Please connect a sinusoidal signal of 1 6 MHz and 366 mU rms 2 55 dBm to chann el 1 input Press any key to continue Checking instrument PXI11 6 6 INSTR Instrument model Instrument options Manufacturer Firmware revision Serial number Simulate Reference signal Waveform Frequency Amplitude US3 3A CH2 LK2 F16 AUG INT PKD TSR M46 SR3 eysight Technologies CTRL FPGA 1 6 285 52268 DPU FPGA 3 2 561 52244M FE CPLD 23 US66675651 False Sinusoidal 1 0 M a Hz 366 mU rms 2 55 dBm Acquisition parameters ecord size 16000 Sample rate 2 OE 00 Coupling parameters Level Channeli 1 00 U 4 06 U AgMD2Vert icalCouplingDC 6 66 U Slope AgMD2TriggerS lopePositive Delay 5 25 us ActiveSource Internali Acquiring data gt OK Signal amplitude 3 mU eference mU Error 6 41 z gt OK Signal RMS 300 59 mU Reference 366 66 mU Error 0 20 z gt OK Signal frequency 1 666 MHz Reference Error Instrument PRI11 6 6 INSTR c
7. ber can also be read from the Soft Front Panel interface but only after the hardware is installed Description of failure or service required 4 Pack the module in its original ESD bag and packing carton Ifthe original carton is not available use bubble wrap or packing peanuts and place the instrument ina sealed container and mark the container FRAGILE 5 On the shipping label write ATTENTION REPAIR DEPARTMENT and the RMA num ber lf any correspondence is required refer to the product by serial number and model number Keysight U5303A Startup Guide Step 2 Verify U53803A Shipment Contents step 2 Verify U5303A Shipment Contents The following items are also included with your Us303A PCle High Speed Digitizer order Part Number Quantity Description U5303A PCle High Speed Digitizer U1092 80001 1 Coaxial cable MMCX to BNC 1 m 8121 2531 Auxiliary power cable 4 Pin Male to Female 4 Conductor Floppy 8121 2533 Auxiliary power cable 15 Pin SATA Power Male to Power 4 Pin Floppy M9700 10001 Keysight MD2 High Speed Digitizer Software amp Product Information CD E2094 60003 Keysight IO Libraries Suite CD U5303 90001 Startup Guide in hard copy U5300 10001 High Speed Digitizers Applications Installation DVD for Windows 50962 04760 Certificate of Calibration 5964 8178 Form determining recalibration due date 9320 6741 1 ROHS China addendum All the files contained on the CDs are available for d
8. e Type MMCX SMA Micro USB MMCX MMCX MMCX MMCX Description External trigger input 50 Q DC terminated 5 V range Analog signal inputs DC coupled and 50 Q terminated The input full scale ranges are selectable Range Maximum Input 1V 3 Vrms 3 6 Vpk 2V 4 3 Vrms 6 3 Vpk Provides connection to the DPU for use with the U5340A FPGA Development Kit Trigger Out signal User selectable from several functions User configurable Input Output signal 3 3 V CMOS and TTL compatible External clock input AC coupled and 50 Q terminated signal level 5 to 15 dBm Please refer to datasheet for details External reference clock input AC coupled and 50 Q ter minated It can accept a 100 MHz signal from 3 to 3 dBm 20 Front Panel LEDs Indicator Purpose Color State DPU DPUstatus Off Z Green blinking Green Q White White blinking Z Green blinking Z Yelow blinking Red blinking Green STATUS Module Status Meaning DPU is not configured Module initialization in progress Module OK firmware not yet loaded DPU firmware loaded ready Firmware initialization in progress Module initialization in progress Warning Error OK ready lf warning or error status is observed please try the following steps Power cycle the PC If using a PCle expansion chassis observe the power sequence requirements Ifthe error persi
9. eeeteuseeebee ester cexbaloeeneced 14 Keysight IO Libraries Suite IOLS 02 2222 cece cece eee ccc cece cece cece eeeeeeees 14 Instrument software 6 cuicicwnicos noboeesiovoencedueudonsuwuwdeesodwanschgeutencsieccesdoemsess 14 High Speed Digitizers Applications DVD for Windows 2222 222 eee ee eee eee eee 14 step 4 Install the Module 0 00 2 o occ c cece cece cece cece eeeeee 16 Fitting the module with the optional card retainer into your PC 2 2 2222222222 eee t U5303A Front Panel Features 1 2 02 oe c cece eee ce cece cece ccc cececeecceecccceeeees 19 Front Panel Connectors 0222 cic e eee c cee cee cece eee cee cence ee eeeeeeceeseeeees 19 PODE an ES ope oot oe E E E E E EE 20 Step 5 Verify Operation of the U5303A Module 2 2 e eee eee ee cece eee ees 21 Perform a Verification of the U5303A optional 02 2c eee eee ecceeeecceceecceceeeeees 22 Requirements for Verification 2 el cece cece cece cece ec ceeccecccccccecceeseeeseees 22 Required Hardware 2 eee cece cece cece cece ccceccccceecceecceecceeccececeseceseerees 22 Operational Verification Procedure 2 i cece cee cee cee cee cee eee eee cece eeee 22 yi Documentation Map Startup Guide Keysight High Speed Digitizer Keysight UoxA KEYSIGHT TONOS Product CD DVD Product website M9703A AXle Digitizer User Guide Save chm file to your local drive for viewing 2014 10
10. fixed product label above indicates that you must not discard this electrical electronic product in domestic household waste Product Category With reference to the equipment types in the WEEE directive Annex 1 this product is classified as Monitoring and Control instrumentation product Do not dispose in domestic household waste To return unwanted products contact your local Keysight office or for more information see http about keysight com en companyinfo e nvironment takeback shtml A Ata This symbol indicates the instrument is sensitive to electrostatic discharge ESD ESD can damage the highly sensitive components in your instrument ESD damage is most likely to occur as the module is being installed or when cables are connected or disconnected Protect the circuits from ESD damage by wearing a grounding strap that provides a high resistance path to ground Alternatively ground yourself to discharge any built up static charge by touching the outer shell of any grounded instrument chassis before touching the port connectors A This symbol on an instrument means caution risk of danger You should refer to the operating instructions located in the user documentation in all cases where the symbol is marked on the instrument D This symbol indicates the time period during which no hazardous or toxic substance elements are expected to leak or deteriorate during normal use Forty years is the expected
11. for ensuring that the equipmentis operated within its spe cifications and operating limits and for ensuring operators are adequately trained Operators use the productfor its intended function They must be trained in electrical Safety procedures and proper use of the instrument They must be protected from electric shock and contact with hazardous live circuits Maintenance personnel perform routine procedures on the product to keep it oper ating properly for example setting the line voltage or replacing consumable mater ials Maintenance procedures are described in the user documentation The procedures explicitly state if the operator may perform them Otherwise they should be performed only by service personnel Service personnel are trained to work on live circuits perform safe installations and repair products Only properly trained ser vice personnel may perform installation and service procedures Operator is responsible to maintain safe operating conditions To ensure safe operating conditions modules should not be operated beyond the full temperature range specified in the Environmental and physical specification Exceeding safe operating conditions can result in shorter lifespans improper module performance and user safety issues When the modules are in use and operation within the specified full temperature range is not maintained module surface temperatures may exceed safe handling conditi
12. heck successful gt Verify resource PRI11 6 6 INSTR Selection Cor CENTER to exit gt AgMD2Verify checks the version of the Control FPGA firmware If the version is not up to date the tool will automatically propose to update the firmware using the Firmware Update Utility Once the Control FPGA firmware has been updated successfully please power off your computer and restart it again for the update to take effect You may then proceed with the AgMD2Verify utility as described in this section If a Problem is Found Verify that you have made all configuration settings as shown above 2 Verify that the RF generator is ON and producing the desired signals at the end of the cable This can be done with an oscilloscope 3 Verify that the problem is reproducible Contact Keysight technical support for assistance Contact details may be found at www keysight com find contactus Keysight U5303A Startup Guide 23 KEYSIGHT TECHNOLOGIES This information is subject to change without notice Keysight Technologies 2013 2015 Edition 4 July 2015 Printed In USA U5303 90001 www keysight com
13. its standard commercial license which is embodied in its End User License Agreement EULA a copy of which can be found at http www keysight com find sweula The license set forth in the EULA represents the exclusive authority by which the U S government may use modify distribute or disclose the Software The EULA and the license set forth therein does not require or permit among other things that Keysight 1 Furnish technical information related to commercial computer software or commercial computer software documentation that is not customarily provided to the public or 2 Relinquish to or otherwise provide the government rights in excess of these rights customarily provided to the public to use modify reproduce release perform display or disclose commercial computer software or commercial computer software documentation No additional government requirements beyond those set forth in the EULA shall apply except to the extent that those terms rights or licenses are explicitly required from all providers of commercial computer software pursuant to the FAR and the DFARS and are set forth specifically in writing elsewhere in the EULA Keysight shall be under no obligation to update revise or otherwise modify the Software With respect to any technical data as defined by FAR 2 101 pursuant to FAR 12 211 and 27 404 2 and DFARS 227 7102 the U S government acquires no greater than Limited Rights as defined i
14. n FAR 27 401 or DFAR 227 7103 5 c as applicable in any technical data safety Notices CAUTION A CAUTION notice denotes a hazard It calls attention to an operating procedure practice or the like that if not correctly performed or adhered to could result in damage to the product or loss of important data Do not proceed beyond a CAUTION notice until the indicated conditions are fully understood and met A WARNING notice denotes a hazard It calls attention to an operating procedure practice or the like that if not correctly performed or adhered to could result in personal injury or death Do not proceed beyond a WARNING notice until the indicated conditions are fully understood and met The following safety precautions should be observed before using this product and any associated instrumentation This product is intended for use by qualified personnel who recognize shock hazards and are familiar with the safety precautions required to avoid possible injury Read and follow all installation operation and maintenance Information carefully before using the product If this product is not used as specified the protection provided by the equipment could be impaired This product must be used in a normal condition in which all means for protection are intact only The types of product users are Responsible body is the individual or group responsible for the use and main tenance of equipment
15. nsert the module into the PCle slot of the PC ensuring that it is fully seated into the PCle bus connector 3 Fixthe module to the PC either by fitting a screw or by using a method integral to your PC model 4 Fully extend the card retainer and ensure that it is inside the PC chassis support Slot 5 Tighten the screw A 0 5 Nm torque Keysight U5303A Startup Guide 17 Step 4 Install the Module Diagram showing fan support assembly fixings U5303Ashown as example Removing the card retainer 1 Remove the screw A in the figure 2 Withdraw the card retainer Installing the card retainer if not previously fitted 1 Slide the card retainer onto the fan module and fit screw A to the top of the retainer Reversing the orientation of the fan assembly 1 Remove the 4 screws B nearest to the front of the fan unit 2 Slide the fan unit approximately 15 mm to the rear until it clears the circuit board disconnect the power cables and rotate the fan unit by 180 3 Reconnect the power cables 4 Slide the fan unit back towards the module until It is fully seated into the loc ating slots 5 Refit the 4 screws push the fan unit upwards away from the circuit board and tighten the four screws 0 5 Nm torque 18 Keysight U5303A Startup Guide U5303A Front Panel Features Front Panel Connectors Connector TRG IN IN 1 2 JTAG TRG OUT 1 0 1 2 3 CLK IN REF IN Keysight U5303A Startup Guid
16. on the left Ifthe module does not appear in the Keysight Connection Expert first try the rescan All button If that does not work restart your PC or embedded controller and restart Keysight Connection Expert again A verification utility may be launched by selecting Start Soft Front Panel which starts the AgMD2Verify utility Keysight U5303A Startup Guide 21 Perform a Verification of the U5303A optional Requirements for Verification The correct operation of the U5303A may be verified by the use of a simple application which carries out several performance checks ona signal acquired from an external Function Generator Required Hardware An external signal source is required Almost any sine wave or function generator capable of generating a signal with an amplitude of 8300 mV rms into 50 Qata frequency of 1 MHz may be used Hardware Description Analog Signal Generator e g Keysight N5181A E4428C SMA cable 50 Q Coaxial cable with SMA m Operational Verification Procedure Do not exceed the maximum voltage level at the INPUT connector 3 4 V DC 1 Configure the RF Generator to produce a Sine signal with a Frequency of 1 0 MHz an Amplitude of 300 mV rms 2 55 dBm 2 Connect the Signal Generator output to the IN 1 connector and turn on the out put 3 Launch the AgMD2Verify utility from Keysight Connection Expert as explained in step 5 of this Startup Guide A command shell window will open 4
17. ons which can cause discomfort or burns if touched In the event of a module exceeding the full temperature range always allow the module to cool before touching or removing modules from chassis Keysight products are designed for use with electrical signals that are rated Measurement Category and Measurement Category Il as described in the International Electrotechnical Commission IEC Standard IEC 60664 Most measurement control and data I O signals are Measurement Category and must not be directly connected to mains voltage or to voltage sources with high transient over voltages Measurement Category II connections require protection for high transient over voltages often associated with local AC mains connections Assume all measurement control and data I O connections are for connection to Category sources unless otherwise marked or described in the user documentation Exercise extreme caution when a shock hazard is present Lethal voltage may be present on cable connector jacks or test fixtures The American National Standards Institute ANSI states that a shock hazard exists when voltage levels greater than 30V RMS 42 4V peak or 6OVDC are present A good safety practice is to expect that hazardous voltage is present in any unknown circuit before measuring Operators of this product must be protected from electric shock at all times The responsible body must ensure that operators are prevented access and o
18. or a static safe work station when working on circuitry with a voltage potential greater than 500 volts Inspect for Damage After unpacking a module inspect it for any shipping damage Report any damage to the shipping agent immediately as such damage is not covered by the warranty see warranty information at beginning of this document i ua o To avoid damage when handling a module do not touch any exposed components or connector pins Keysight U5303A Startup Guide Step 1 Unpack and Inspect the Module See www keysight com for information on preventing damage to your Keysight equipment Return a Module for Service Should tt become necessary to return a module for repair or service follow the steps below 1 Review the warranty information shipped with your product 2 Contact Keysight to obtain a Return Material Authorization RMA and return address For assistance finding Keysight contact information go to www key sight com find assist worldwide contact information for repair and service or refer to the Support information on the product web page at www key Ssight com find U5303A 3 Write the following information on a tag and attach it to the malfunctioning equip ment Name and address of owner A P O box is not acceptable as a return address Product model number for example U53034 Product serial number The serial number label is located on the top cover of the module The serial num
19. ownload at www keysight com find U5303A 12 Keysight U5303A Startup Guide step 3 Install the Software system Requirements Item Operating system Windows 7 32 or 64 bit All versions Windows 8 1 32 or 64 bit All versions Note If using High Speed Digitizers Applications DVD Windows 7 64 bit is supported Processor speed 1 GHz 32 bit x86 1 GHz 64 bit x64 no support for Itaniumo4 Available memory 1 GB minimum Available disk space 2 5 GB available hard disk space includes 1 5 GB for Keysight IO Libraries Suite 1 GB for Keysight MD2 Note 400MB for High Speed Digitizers Applications Video Support for DirectX 9 graphics with 128 MB graphics memory recommended Super VGA graphics is supported Browser Microsoft Internet Explorer 7 0 or higher Step 3 Install the Software Linux Kernel 2 6 or higher 32 or 64 bit Debian 7 0 CentOS 6 As per the minimum requirements of the chosen distribution As per the minimum requirements of the chosen distribution 100 MB No graphics required for headless system or X Windows Distribution supplied browser Because of the installation procedure less disk space may be required for operation than is required for installation The amount of space listed above is required for installation Hardware Requirements A PC running one of the above operating systems Recommended models are HP 2420 HP Z440 or Dell T3610 Keysight U5303A S
20. pprovals may be used if the rating and type are the same Other components that are not safety related may be purchased from other suppliers as long as they are equivalent to the original component note that selected parts should be purchased only through Keysight to maintain accuracy and functionality of the product If you are unsure about the applicability ofa replacement component call an Keysight office for information No operator serviceable parts inside Refer servicing to qualified personnel To prevent electrical shock do not remove covers For continued protection against fire hazard replace fuse with same type and rating PRODUCT MARKINGS The CE mark is a registered trademark of the European Community O Australian Communication and Media Authority mark to indicate regulatory compliance as a registered supplier ISM GRP 1 CLASS A This symbol indicates product compliance with the Canadian Interference Causing Equipment Standard ICES 001 It also identifies the product is an Industrial Scientific and Medical Group 1 Class A product CISPR 11 Clause 4 South Korean Class A EMC Declaration This equipment is Class A suitable for professional use and is for use in electromagnetic environments outside ofthe home A 8a 712 8 F845 AJAA OWIAESFSSAS AN TASS DOA SLENSHE Ol SS OHA kek A 24E Qs ASQA ABS OE AS Sale SL CH X This product complies with the WEEE Directive marketing requirement The af
21. r insulated from every connection point In some cases connections must be exposed to potential human contact Product operators in these circumstances must be trained to protect themselves from the risk of electric shock If the circuit is capable of operating at or above 1000V no conductive part of the circuit may be exposed Do not connect switching cards directly to unlimited power circuits They are intended to be used with impedance limited sources NEVER connect switching cards directly to AC mains When connecting sources to switching cards install protective devices to limit fault current and voltage to the card Before operating an instrument ensure that the line cord is connected toa properly grounded power receptacle Inspect the connecting cables test leads and jumpers for possible wear cracks or breaks before each use When installing equipment where access to the main power cord is restricted such as rack mounting a separate main input power disconnect device must be provided in close proximity to the equipment and within easy reach of the operator For maximum safety do not touch the product test cables or any other instruments while power is applied to the circuit under test ALWAYS remove power from the entire test system and discharge any capacitors before connecting or disconnecting cables or jumpers Installing or removing switching cards or making Internal changes such as installing or remo
22. s Applications DVD for Windows High Speed Digitizers Applications install the software necessary for the options your have ordered This software Is included with your shipment DVD part number U5300 10001 14 Keysight U5303A Startup Guide Step 3 Install the Software 1 First install Keysight MD2 High Speed Digitizer Software 2 From the High Speed Digitizers Applications DVD launch the installer 3 Follow the installer prompts and select the applications your want to install Keysight U5303A Startup Guide I5 Step 4 Install the Module step 4 Install the Module 1 2 4 Ensure that the PC Is switched off and disconnect the power cord Open the PC case Follow ESD precautions when handling and installing the U5303A The U5303A features a x8 PCle bus Interface and should be Installed in either a x8 or x16 Slot When installing the U5303A ensure that it has optimum cooling do not install it in a position where the integrated cooling fans may be obstructed The module requires an additional auxiliary power connection to the white connector at top edge of the module If your PC has a free floppy drive power connector simply attach this If your PC does not have a free connector of this type you may use one of the two Supplied adapters fyour PC has spare 4 pin Molex power connectors use the supplied adapter 8121 2531 fyour PC only has the newer SATA power connectors use the supplied adapter 8121
23. startup Guide Keysight Us303A PCle High Speed Digitizer 2 channels 12 bit up to 3 2 GS s DC up to 2 GHz bandwidth with custom firmware support 3 AA KeysicHT High Speed Digitizer Notice This document contains references to Agilent Please note that Agilent s Test and Measurement business has become Keysight Technologies For more information go to www keysight com KEYSIGHT TECHNOLOGIES Notices Copyright Notice Keysight Technologies 2013 2015 No part of this manual may be reproduced in any form or by any means including electronic storage and retrieval or translation into a foreign language without prior agreement and written consent from Keysight Technologies Inc as governed by United States and international copyright laws Manual Part Number U5303 90001 Published By Keysight Technologies Chemin des Aulx 12 1228 Plan Les Ouates Switzerland Edition Edition 4 July 2015 Printed In USA Regulatory Compliance This product has been designed and tested in accordance with accepted industry standards and has been supplied in a safe condition To review the Declaration of Conformity go to http www keysight com go conformity Warranty THE MATERIAL CONTAINED IN THIS DOCUMENT IS PROVIDED AS IS AND IS SUBJECT TO BEING CHANGED WITHOUT NOTICE IN FUTURE EDITIONS FURTHER TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW KEYSIGHT DISCLAIMS ALL WARRANTIES EITHER
24. sts please contact Keysight technical support Keysight U5303A Startup Guide Step 5 Verify Operation of the U5303A Module step 5 Verify Operation of the U5303A Module The intention of this step is to verify correct operation of the newly installed module Run Keysight Connection Expert by clicking the task bar icon i0 Connection Expert and select It will display the modules that are installed Review the configuration data and then launch the AgMD2Verify SFP This will provide control of the module for self test and other operational verification procedures Keysight U5303A Instrument Properties g Keysight Connection Expert PXI AXIe Chassis Manual Configuration Settings Instruments Details for Agilent Technologies U5303A Manufacturer Agilent Technologies Model U5303A Start Soft Front Panel Connection Strings VISA Addresses Px14 0 0 INSTR Pxi0 4 0 0 INSTR VISA Aliases No VISA aliase Send Commands To Start IO Monitor Add or Change Aliases Modular Information Slot 1 Go to Chassis View Installed Drivers 32 bit IVI driver version 1 5 0 0 Update Drivers 64 bit IVI driver version 1 5 0 0 ssages 2 Clesr Remote IO Server Off 9 50 49 AM Instruments are already discovered and configured 9 50 48 AM User interface session started View Instrument Information Online x The instrument properties may be viewed by clicking on the desired instrument from the list
25. tartup Guide Step 3 Install the Software Install the Software Ifthe Agilent MD2 software is installed on your computer first uninstall the Agilent MD2 software from the Control Panel gt Programs and Features before installing the Keysight MD2 High Speed Digitizer Software Keysight IO Libraries Suite IOLS Keysight IO Libraries Suite OLS which includes the Keysight Connection Expert This software is included with your shipment CD part number E2094 60003 and is also available at www keysight com Tind Osuite This software must be installed first 1 From the Keysight IOLS CD E2094 60003 browser launch the installer 2 Follow the installer prompts to install the IO libraries Version 16 3 update 2 or higher of the Keysight IO Libraries Suite is required Instrument software Instrument software which includes device drivers IVI C IVI COM and documentation for your module This software is included with your shipment CD part number M9700 10001 1 From the Keysight MD2 High Speed Digitizer Software amp Product Information CD launch the installer 2 Follow the installer prompts Choose a Complete installation to install all soft ware and documentation ora Custom installation to select from a listing of components and other features 3 After installation is complete please shut down the PC Version 1 6 or higher of the Keysight MD2 High Speed Digitizer Software is required High Speed Digitizer
26. useful life of the product CLEANING PRECAUTIONS To prevent electrical shock disconnect the Keysight Technologies instrument from mains before cleaning Use a dry cloth or one slightly dampened with water to clean the external case parts Do not attempt to clean internally To clean the connectors use alcohol in a well ventilated area Allow all residual alcohol moisture to evaporate and the fumes to dissipate prior to energizing the instrument Contents Documentation Map 0 2 2 2 cece c eee eee cece cece eeeceeeeeeeeeee U5303A PCle High Speed Digitizer Introduction 2 22 c cece cece eee eeeee 8 Step 1 Unpack and Inspect the Module 2 2 00 2 c ccc eee cccccceeeeccceceeeees 10 Electrostatic Discharge ESD Precautions 000 000 e cece cece eee eeeeeees 10 Inspect for Damage 2 eee eee cece cece cece eee e cece ec eceecececceeeceueceeueeeeeeeeues 10 Return a Module for Service 2c c ucccasuscsceaccahenadienesdusivennaedd tues awetebadeaeekeueeuds 11 Step 2 Verify UB303A Shipment Contents aa 00000000000000000000000000000100000nn 12 Step 3 Install the Software 2 2 eee cece cece cece ee eecccccceeecccccceeeeeeecccceeeees to System Requirements eee eee eee cece cence cence enc cenccccecececccceccceneeees 13 Hardware Requirements 2 2 2 eee ec cece ccc ccc cee cece ccecccecceccceeccecececceesceeeeee 13 Installthe SOMWalS uc cicnnxac mnce cee S6Gmanauebeaendanackas dale
27. ving jumpers Do not touch any object that could provide a current path to the common side of the circuit under test or power line earth ground Always make measurements with dry hands while standing on adry insulated surface capable of withstanding the voltage being measured The instrument and accessories must be used in accordance with its specifications and operating instructions or the safety of the equipment may be impaired Do not exceed the maximum signal levels of the instruments and accessories as defined in the specifications and operating information and as shown on the instrument or test fixture panels or switching card When fuses are used in a product replace with the same type and rating for continued protection against fire hazard Chassis connections must only be used as shield connections for measuring circuits NOT as safety earth ground connections If you are using atest fixture keep the lid closed while power is applied to the device under test Safe operation requires the use of a lid interlock Instrumentation and accessories shall not be connected to humans Before performing any maintenance disconnect the line cord and all test cables To maintain protection from electric shock and fire replacement components in mains circuits including the power transformer test leads and input jacks must be purchased from Keysight Standard fuses with applicable national safety a
Download Pdf Manuals
Related Search