TS-5 User Manual - 3ality Technica
Contents
1. Camera roll axis turn round centerline 2 Absolute rail deviation end to end 0 05 mm Drive Accuracy m Encoder Accuracy 1 m Linear encoder on final stage post gearing etc Interaxial 50 8 mm s 2 s Multiple UNC3 8 16 female threads ALITY 5 2 Connectors and Interfaces 5 2 1 Lens Motors Lemo 7pin Pin Function Direction female receptacle 1 Motor M Output assignment 2 Motor M Output 3 Encoder A Input 4 5VDC Output 5 GND 6 Encoder B Input 7 Rear view on TS 2 s Female Lemo7 receptacle Connector on TS 4 S LEMO 7pin female receptacle Size 1B ATTENTION Use shielded cables only 5 2 2 SPC SIP I O Lemo 10pin Pin Function Direction female receptacle gt ds Output __ assignment 3 TA Output OA 4 TB Output 5 RA Input 3 40 6 6 RB Input 4 S nc l Rear view on TS 2 s Female Lemo10 receptacle 9 12VDC Output 10 GND Connector on TS 4 S LEMO 10pin female receptacle Size 1B ATTENTION Use shielded cables only TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY 5 2 3 Power Input 25 Voltage 12VDC 10 10 8 15VDC XLR pin assignment 1 OV GND for electronics internal motors and power output X6 at right camera 2 OV GND for power outputs X27 at left camera 3 12V for power outputs X27 at left Rear view on TS 4 S camera 4 12V for electronics internal motors and power output X6 at right camera Current 2 6Amax2. 2010 3ality Technica Systems LLC All rights reserved Reproduction adaptation or translation of this document without prior permission is prohibited except as allowed under copyright laws Note The information in this document is subject to change without notice or obligation Technical Support Telephone 1 818 333 3010 Fax 1 818 333 3001 Email support 3alitytechnica com Web www 3alitytechnica com support Address Customer Service 3ality Technica Systems LLC 55 E Orange Grove Ave Burbank CA 91502 United States of America Hours 9 00am to 6 00pm Pacific Time Monday through Friday TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY United States of America USA Federal Communications Commission FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Class rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference which the user will be required to correct at his expense To assure continued compliance follow the attac
3. 4 PREPARING THE STEREO CAMERA PLATFORM 15 4 1 CAMERA LENS SLED ASSEMBLY 15 4 1 1 CAMERA MOUNTS 16 4 1 2 MOUNTING BRACKETS MOTORS AND CAMERA 17 4 2 INSTALLING THE BEAMSPLITTER 19 4 2 1 REMOVING AND CLEANING THE BEAMSPLITTER 20 5 SPECIFICATIONS 21 5 1 PHYSICAL 21 5 2 CONNECTORS AND INTERFACES 22 5 2 1 LENS MOTORS 22 5 2 2 SPC SIP1 O 22 5 2 3 POWER INPUT 23 5 2 4 POWER OUTPUTS 23 5 3 MECHANICAL 24 6 APPENDIX 25 6 1 DECLARATIONS OF CONFORMITY 25 6 1 1 CE 25 TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY 1 Official Notices 1 1 Limitation of Liability 3ality Technica LLC shall not be liable for indirect special incidental or consequential damages for damages that directly or indirectly arise from the use of or inability to use the system for commercial loss of any kind for the procurement of substitute goods whether arising in tort contract or any other legal theory even if 3ality Technica LLC has been advised of the possibility of such damages In any event 3ality Technica LLC s liability shall be limited to the amount actually paid for the system giving rise to any such damage This limitation is intended to limit 3ality Technica LLC s liability and shall notwithstanding any failure of essential purpose of any limited remedy 1 2 Software License Agreement IMPORTANT READ CAREFULLY This Software License Agreement is a legal agreement between 3ality Technica s Customer and 3ality
4. any acts or omissions of any government or governmental authority natural disaster act of a public enemy riot sabotage dispute or differences with workmen power failure delays in transportation or deliveries of supplies or materials acts of God terrorism or any events reasonably beyond the control of Customer Indemnification Customer shall release defend indemnify and hold harmless 3ality Technica from and against any claims damages and liability arising from use of the Software or Documentation by Customer 1 5 Obtaining Warranty Service and Customer Support The following information describes our current warranty support procedures These procedures are subject to change without notice and are expressly excluded from the Limited Warranty Our Customer Support Representatives are available to provide telephone support during business hours M F 9am 6pm Pacific Time and after these hours for urgent emergency technical support e Customer Support will be provided only for products under warranty or those covered under a valid Support Agreement e Before returning the Product for repair it is necessary to obtain a Return Merchandise Authorization RMA number by calling 818 333 3000 You will be asked to provide the system s serial number e The non functioning part should be properly packed and shipped pre paid to 3ality Technica with the RMA number clearly displayed on the outside of the package and on the accompanying RMA
5. conducted by an authorized Company service representative at an authorized repair facility The customer is responsible for costs associated with shipping the equipment to and from an authorized repair facility d This warranty is for the hardware and hardware sub systems of the equipment and specifically excluded from the warranty is all software which is covered under the software warranty problems due to accidents misuse misapplication storage damage negligence or modification to the Equipment or its components e Company does not authorize any person or party to assume or create for it any other obligation or liability in connection with the Equipment except as set forth herein f The warranty in section a above is exclusive and in lieu of all other indemnities or warranties whether express or implied including the implied warranties of merchantability and fitness for a particular purpose TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY Limitation of Liability In no event shall company be liable for any indirect incidental punitive special or consequential damages or damages for loss of profits revenue or use incurred by customer or any third party whether in an action in contract or tort or otherwise even if advised of the possibility of such damages Company s liability for damages arising out of or in connection with this agreement shall in no event exceed the purchase price of the
6. Declarations of Conformity 6 1 1 CE DECLARATION OF CONFORMITY x E24 This declaration is valid for following product Equipment Stereo Camera Platform Type 3FLEX TS 2 Studio Hereby the equipment is confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility 2004 108 EEC The following company is responsible for this declaration 3ality Digital Systems LLC 55 E Orange Grove Ave Burbank CA 91502 United States of America Authorized Representative in the EC 3ality Digital Systems GmbH Gut Mergenthau D 86438 Kissing Bavaria Germany Europe The measurements were carried out in accredited laboratories For the evaluation of above mentioned Council Directives for Electromagnetic Compatibility and for Low Voltage following standards were consulted e EN 61000 6 2 2005 General Standards Immunity for Industrial Environments e EN 61000 6 3 2007 General Standards Emission standards for residential commercial and light industrial environments P 97 Signature of respo nsible Person Kissing March 15 2010 Place Date Figure 13 Declaration of Conformity TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011
7. ITY 8 Replace the top bar taking care with the clamp To do this first contact the mirror s surface with the rubber tips and then snap into place securing the bar with the locking screws 4 2 1 Removing and Cleaning the Beamsplitter Note Beamsplitter mirror removal and installation is not for the faint of heart and requires great care and confidence Do not hurry this process A clean beamsplitter is a prerequisite for premium quality images While there are many ways to clean a mirror these are our recommendations At 3ality we prefer lens cleaners that contain Isopropyl Alcohol and not much else Pancro lens cleaning fluid is our favorite http www filmtools com panlencleanf html Also we prefer the Kimtech Kimwipes part number 34256 www kimtech com While non abrasive normal lens tissues are far too small and not absorbent enough for such a large task We also recommend the use of disposable white cotton inspection gloves for the handling of the glass Dispose of the gloves after a single use as they collect dirt and oil you do not want on your glass Start by using clean and dry pressurized air of some type to clear any hard deposits that might scratch the surface of the glass while wiping When you are satisfied that any hard debris has been cleared proceed to spray the glass cleaner on the mirror The Pancro fluid is a fine mist spray We recommend the spraying of the entire surface of the glass Usually 3 to 4 pumps of s
8. PC motor control interface box SPC motor control interface box cable 12 volt Y power cable 4pin Female XLR to 2 4pin Male XLR Ui W N N N N TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY 4 Preparing the Stereo Camera Platform 4 1 Camera Lens sled assembly 1 Disconnect platform power 2 Remove camera sled from camera platform by loosening the knob above the height pitch bracket 3 Carefully pulling the spring loaded safety lock knob remove the sled from the platform The knob is designed to catch in each of the camera platform s grooves Take care not to force anything gt Mounting Knob Ga 4 a a Cir 10 Ber 22 ee Spring loaded iem safety lock knob Figure 5 Right eye camera assembly TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 SALIT T E C H N C AR 4 1 1 Camera Mounts 4 You will have camera mounts for the camera you specified to 3ality Technica at the time of purchase If you have multiple cameras ensure you are using the set designated for your camera 1 Attach mounting brackets to top and bottom of camera body 1 2 2 Attach mounted camera body to top and bottom of dovetail plate camera body remains detached in the center 3 4 Figure 6 Mounting brackets and dovetai
9. SALIT Y 3FLEX TS 5 Compact Compact Beam Splitter Stereo Camera Platform Version 1 0 User Manual 44 1 f 459 S PST f S e TV Ad WM di Aw 4 NS c n IE SSS Qj SN SS x SN 3 SSN III SSSR COPYRIGHT 2010 3ALITY TECHNICA LLC ALL RIGHTS RESERVED TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY Authors AnEs Andreas Eser GaUs Gary Ushino MaBe Martin Beck JiSm Jill Smollin Revision History Revision Date Authors Changes U S Q GL 3 October 2010 Initial Draft to 3ality 14 September 2011 Intended Readers Users Operators Subject How to setup the TS 5 Compact Document Version Date V 1 0 September 2011 Applicable for Device Version TS 5 Compact Filename TS 5 Compact UserManual 1 0 doc TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY Preface This document contains instruction and reference information for the operation and use of the 3FLEX TS 5 Compact_BeamSplitter Stereo Camera Platform Trademarks 3FLEX 3PLAY and 3ACTION are trademarks of 3ality Technica LLC All other brand and product names mentioned herein are used for information purposes only and may be trademarks or registered trademarks of their respective companies 3FLEX TS 5 Compact_BeamSplitter Stereo Camera Platform User Manual Copyright
10. Technica LLC This system contains certain 3ality Technica software hardware associated media printed materials and electronic documentation By using the system described in this manual the customer agrees to be bound by the terms of this Software License Agreement If the customer does not agree to the terms of this Software License Agreement 3ality Technica LLC is unwilling to license the software to the customer In such case the customer may not use or copy the software License 3ality Technica LLC grants an exclusive nontransferable limited license to use the installed software exclusively on hardware on which 3ality Technica has installed the software or on hardware on which 3ality Technica has authorized it to be installed for the period of time that the software is licensed Such software may only be enabled activated modified or updated by 3ality Technica or its authorized agent 3ality Technica and its licensors retain the right title and interest in and to all software Title to the media on which the software is delivered is transferred to the Customer Restrictions The software is copyrighted and may contain material that is protected by patent trade secret or other laws pertaining to proprietary rights No copies of the software may be made except for a single copy for archival purposes You may not modify the Software or permit or assist any third party in doing so You may not decompile reverse engineer disassemble or oth
11. defective equipment The provisions of this agreement allocate risks between company and customer Company s pricing reflects this allocation of risk and but for this allocation and limitation of liability company would not have entered into this agreement 1 4 3ality Technica Software Warranty 3ality Technica represents and warrants that the Software shall perform substantially as represented in the Documentation WARRANTY LIMITATION THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND WARRANTIES OF MERCHANTABILITY EXCEPT FOR THE WARRANTY EXPRESSLY ACKNOWLEDGED HEREUNDER 3ality Technica HEREBY DISCLAIMS AND CUSTOMER HEREBY WAIVES ALL WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ALL IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND IMPLIED WARRANTIES OF MERCHANTABILITY Limitation of Damages 3ality Technica shall not be liable to Customer under the Warranty for any consequential exemplary incidental or punitive damages regardless of whether 3ality Technica has been advised of the possibility of such damages in advance or whether such damages are reasonably foreseeable Force Majeure 3ality Technica shall not be liable to Customer for failing to perform its obligations under the Agreement because of circumstances beyond the control of Customer Such circumstances shall include but not be limited to
12. erwise reduce the Software to source code or other human readable form or attempt or permit any third party to do so Any violation of this Software license shall be a material breach and shall entitle 3ality Technica LLC to exercise immediately any remedy that may exist at law or in equity Copyright All title and copyrights in the Software and any copies thereof and the accompanying printed materials are owned by 3ality Technica LLC All rights not specifically granted under this Software License Agreement are reserved by 3ality Technica LLC 1 3 3ality Technica Hardware Warranty a Company warrants to the original purchaser of Equipment that for the Warranty Period as defined below the Equipment will be free from material defects in materials and workmanship The foregoing warranty is subject to the proper installation operation and maintenance of the Equipment in accordance with installation instructions and the operating manual supplied to Customer Warranty claims must be made by Customer in writing within sixty 60 days of the manifestation of a problem Company s sole obligation under the foregoing warranty is at Company s option to repair replace or correct any such defect that was present at the time of delivery or to remove the Equipment and to refund the purchase price to Customer b The Warranty Period begins on the date the Equipment is delivered and continues for 12 months c Any repairs under this warranty must be
13. externally limited Connector TS 4 S NEUTRIK XLR 4pin male ATTENTION Use only power supply or battery pack which is compliant with the regulations in your country and make sure that the current of your power supply is internally limited to 6Amax by means of fuses or circuit breakers The usage of the following Y cable is recommended XLR 4pin male CND Ma L er XLR 4pin female From Power Supply 3 12VDC To TS 2 Studio For Motors and Right Camera X6 12VDC 4 12VDC Stereo Camera Platform XLR 4pin male SND From Power Supply For Left Camera X27 i ypc Please use cable with at least 0 75mm or AWG 18 Please keep the cables as short as possible Do not exceed a length of 5 meters 16 ft Figure 12 Recommended Y Power Cable 5 2 4 Power Outputs 25 Voltage 12VDC os 10 8 15VDC XLR pin assignment OV GND n C 12V View on TS 4 S Current Total current for all Power outputs OUT1 OUT2 OUT3 together 6Amax Connector TS 2 s NEUTRIK XLR 4pin female oe it TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY 5 3 Mechanical Attention e All dimensions in mm e Dimensions are rounded e Not to Scale e TS 5 Compact Camera Platform is shown with an arbitrary camera and an arbitrary lens e Design details might change without prior notice TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY 6 Appendix 6 1
14. form We will refuse to accept any package without a valid RMA number e Repairs outside the scope of the Limited Warranty require a valid and valid Support Agreement prior to any repairs 3ality Technica does not offer time and materials based repair services TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY 2 Introduction 3ality Technica s 3FLEX TS 5 Compact BeamSplitter camera platform restores creativity and mobility to the filmmaker Designed by cinematographers and engineers this fully motorized stereoscopic platform accommodates a variety of cameras and lenses Whether you are shooting a feature film or a high profile sporting event the TS 5 is your answer to quick and accurate setups freeing you to shoot 3D on a 2D schedule 3ality Technica s calibration software is sophisticated powerful and easy to navigate providing you with matching zooms and smooth tracking for every shot In addition 3ality Technica s proprietary software captures positional metadata every six milliseconds You can use the metadata to integrate actual camera data into your computer generated environments seamlessly Whatever you can imagine 3ality Technica makes it possible 2 1 Compact BeamSplitter The 3FLEX TS 5 Compact BeamSplitter Camera Platform is the portable alternative to classic BeamSplitter stereo camera rigs With an Interaxial range of 0 4 inches this stereo platform allows the 3D creator to capture dep
15. hed installation instructions and do not make any unauthorized modifications European Commission EC Waste Electrical and Electronics Equipment WEEE Directive Do not dispose of this device At the end of its life cycle this device must be properly recycled by a specialized recycling firm or returned to the manufacturer or vendor for proper disposal Finland Laite on liitett v suojamaadoituskoskettimilla varustettuun pistorasiaan Norway Apparatet m tilkoples jordet stikkontakt Sweden Apparaten skall anslutas till jordat uttag WARNING TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE CAUTION TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE USE THE RECOMMENDED ACCESSORIES ONLY TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY Table of Contents 1 OFFICIAL NOTICES 6 1 1 LIMITATION OF LIABILITY 6 1 2 SOFTWARE LICENSE AGREEMENT 6 1 3 3ALITY TECHNICA HARDWARE WARRANTY 6 1 4 3ALITY TECHNICA SOFTWARE WARRANTY 7 1 5 OBTAINING WARRANTY SERVICE AND CUSTOMER SUPPORT 7 2 INTRODUCTION 8 2 1 COMPACT BEAMSPLITTER 8 2 2 HEIGHT PITCH UNIT 8 2 3 TYPICAL IN SYSTEM CONFIGURATION 8 2 4 RIG OVERVIEW 9 2 5 10 2 5 LENS CONTROL CONNECTORS 10 2 6 TS 5 COMPACT INTERNAL CABLING 11 3 BEFORE YOU START 12 3 1 SAFETY 12 3 1 1 GENERAL SAFETY INSTRUCTIONS 12 3 1 2 SPECIFIC SAFETY INSTRUCTIONS 13 3 2 PARTS NEEDED 14
16. l TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY 1 Slide motor brackets onto plate 1 Figure 7 Motor Brackets 2 Slide motors onto brackets 2 LARGE 3 Tighten into pla SPACE Note This knob tighte both the bracket to th base and the motor i place 3 4 Attach mounted camera body to came Sled 2 LEFT EYE RIGHT EYE Note the large Note the small flange along space along the top the top of the Somewhat in bracket This the shape of T distinguishes an L This 2 2 the right from distinguishes o the left the left from the right Figure 8 4 1 2 Mounting Brackets Motors and Camera TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 Figure 9 1 Mount camera on sled safety screw will help you place the camera lens onto the rig 1 2 Lock with locking clamp Figure 10 ALITY Rig body sled and motors Camera mounted on sled 0055 Cx i imi c Splitter User Manual September 2011 ALITY 4 2 Installing the Beamsplitter Note Beamsplitter Mirror removal and installation is not for the faint of heart It requires great care and confidence Do not hurry this process Tools Soft cotton disposable gloves clean compressed air or photo grade canned air sticky tape style lint roller brush Pancro or Alcohol only glass cleaner Tip To determine
17. pray should cover the glass Using the Kimwipes We recommend that you crumple the large tissue into a loose ball Wet the Kimwipe with a little pancro Dry Kimwipes may still be abrasive to the coating Wipe the surface gently with the crumpled Kimwipe until dry Discard the used Kimwipe Inspect the mirror for further cleaning Start over again if needed Depending on the amount of accumulated oil and dirt you may need several applications of cleaner and wipes before you are satisfied The same applies to the anti reflective side of the glass At 3ality we clean the reflective side of the TS 5 before installation However over time or exposure to smoke and dirty environments you will need to remove and clean the anti reflective side again Tip For determining the reflective side of the glass use a non abrasive object rubber eraser cotton gloved finger etc and touch the surface of the mirror If you can touch your own reflection it is the reflective side of the mirror If there appears to be a gap between your object and the reflection it is the anti reflective side of the mirror Always discard the wipe after first use NEVER reuse the Kimwipe You will reapply the dirt to the glass TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY 5 Specifications 9 1 Dimensions without cameras and lenses Weight without cameras and lenses Operating Height Operating Conditions Storage Condi
18. ructions Do not use this apparatus near water Clean only with dry cloth Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Unplug this apparatus during lightning storms or when unused for long periods of time 13 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply its cord or its plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped eS o sm SS I TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY 3 1 2 Specific Safety Instructions 1 In case of outdoor usage make sure that it the TS 5 Compact BeamSplitter is not exposed to moisture or rain Use appropriate covers in case of moist or wet weather conditions 2 In order to prevent overheating make sure that the device is properly vented especially when used under protective covers 3 Use only certified power supplies with an internal current limiter fuse or trip switch Set this limiter to 6 Ampere max Make
19. s and controls Custom camera mounts attach here Left Eye XLR 4 pin female ALITY 2 5 Lens Control Connectors ER CER s SSS RR E Figure 3 Lens Motor Supplies shown for both cameras Description Comment Right Iris motor Lemo port Right Zoom motor Lemo port Right Focus motor Lemo port Left Focus motor Lemo port Left Zoom motor Lemo port Left Iris motor Lemo port gt Z Note All connectors 7 Lemo TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY 26 TS 5 Compact Internal cabling TS 5 SHOULDER LEFT EYE UNDERSLUNG SPC LOCAL Lemo 10 Female MRCU board SPC REMOTE Lemo 10 Female 1 XLR4 FEMALE POWER OUT V Y Ui o l Power Switch v MRCU Board N 9 pt XLR4 FEMALE POWER OUT pre 1 A T i A 1 E _ 1 SPC LOCAL A XLRA MALE Lemo 10 Female POWER IN 1 N 1 E 1 3 N N TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 ALITY 3 Before you start 3 1 Safety 3 1 1 General Safety Instructions Restrict camera platform operation to qualified personnel only Read these instructions Read these instructions again Keep these instructions Heed all warnings Follow all inst
20. sure that the voltage of your power supply has a nominal voltage of 12VDC with a tolerance of not more than 10 25 10 8 15VDC 4 Ensure that the TS 5 Compact BeamSplitter is always secure on a table or mounted safely on a tripod fluid head remote head Steadi Cam etc with sufficient load capacity 5 Ensure that your connector of the power supplyis always easily accessible 6 Disconnect this power in connector before any assembly or service work Pinch Point Keep hands REFLECTED EYE Figure 4 Camera platforms angle toward and away from each other when converging TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 Be highly attentive when reaching into the camera platform while in use to prevent injuries from unpredictable movement Do not grab under the Height Pitch Unit at any time See picture below for motorized movement areas Moving Parts Height Pitch unit moves vertically On right camera platform only Camera platforms and angle toward and away from each other when converging ALITY 3 2 Parts needed Pos Quantity Description 1 1 3flex TS 5 Compact BeamSplitter 3D Camera Platform 2 2 3flex TS 5 Compact BeamSplitter 3D Camera Platform Camera Lens Sleds One Camera Lens Sled consists of e Heden lens motors Cameras Camera mount adaptors appropriate to camera type matching zoom lenses Heden lens motor interface cables 7pin Male Lemo S
21. th from very close to about 20 feet away 2 2 Height Pitch Unit The Height Pitch unit is unique to all 3ality Technica 3FLEX stereoscopic camera systems Mounted on the TS 5 alongside the right eye camera or through eye this enables the software system to compensate for vertical misalignments which are primarily caused by irregularities in the internal mechanisms of zoom lenses 2 3 Typical In System Configuration HD SDI Video 3FLEX SIP Stereo Image Processor _ m Stereo Platform Stereo Platform Controller 9 Controller L me f m F Z la Power Supply IZ J Motion Control video gt 3ality Technica Third Party Products D c S Figure 1 Typical In System Configuration TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 2 4 Rig Overview O T 2 2 AW ALITY Figure 2 View from Above Right without cameras and lenses Description Base Plate Locking Safety Pin Height Pitch Unit Lens Motors Power In Power Out 10 Pin Lemo to SPC MRCU board with power switch Camera support plate with roll axis adjustment Lens Motors cables Left Camera Power Out TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 Comment Right Eye XLR 4 pin male Input from power supply 3ality proprietary Y power cable XLR 4 pin female Contains motor driver
22. the reflective side of the glass use a non abrasive object rubber eraser cotton gloved finger etc and touch the surface of the mirror If you can touch your own reflection it is the reflective side of the mirror If there appears to be a gap between your object and the reflection it is the anti reflective side of the mirror rang n EI is KAREL Bir ur a 3 4 amp Inner Details of the Mirrorbox 1 Disengage the upper clamps 1 and remove the security strip from the top of the mirror box Place it to the side 2 Disengage the lower inner clamp 2 3 Eliminate any lint and dust particles that have accumulated on the black velvet mirror box interior Use the compressed air and lint roller tools to accomplish this Clean the inside reflective side of the mirror 5 Using the soft cotton gloves hold the mirror with 2 hands anti reflective side up from the bottom or the edge of the mirror The bottom edge is the narrowest part of the trapezoid shape 6 Carefully insert the glass into the mirror box guides and behind the lower clamp The mirror will be secure when it finds the upper groove of the mirror box guide Be careful to place the mirror into its frame rather than dropping it into place 7 Once the mirror is in place close the side mirror clamp 2 The mirror is now secured TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 AL
23. tions Power supply Tolerance of Power Supply Ingress protection RoHS compliance Interaxial Range Convergence Range Currently supported Camera Types Height of optical center camera mount Lens Type Focal Lengths Height Pitch Adjustment Rotation Plane Flatness Positional Accuracy Feedback Method Drive Speed Tripod Head Mount TS 5 Compact BeamSplitter User Manual Version 1 0 September 2011 Physical L 540 mm or 21 W 760 mm or 30 H 330 mm or 13 32 7 kg 72 165 lt 3000 m above sea level Temperature 0 C to 45 C or 32 to 113 F Rel Humidity 20 80 non condensing Temperature 10 C to 55 C or 15 to 131 F Rel Humidity 0 80 non condensing 12V DC 2 x 6Amax Used power supplies must be compliant with the regulations in the countries used and must be current limited to 6Amax by means of fuses circuit breakers or trip switches 25 710 10 8 to 15V IP20 Designed for indoor usage only If used outdoors use appropriate protection measures to prevent exposure of the device to moisture and rain YES Right eye camera movement 4 to 20 inches or 500 mm Convergence each camera 1 to 3 All full body HD cameras Box cameras with optional dove tail mount 96 mm Max Front Lens Diameter 100 mm up to 135mm with optional large lens bracket 2 3 Imager 6 5 mm to 125 mm Super 35 Imager 18 mm to 250 mm Height Range 12 6 mm Pitch Range x 3 7
Download Pdf Manuals
Related Search