User Guide
Contents
1. Intel NUC Kit NUCSPGYH User Guide Intel NUC Kit NUC5PGYH User Guide Intel NUC Kit NUCSPGYH User Guide Before You Begin A CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated with personal computers and with the safety practices and regulatory compliance required for using and modifying electronic equipment Disconnect the computer from its power source and from any telecommunications link or network before performing any of the procedures described in this guide Failure to disconnect power telecommunications links or networks before you open the computer or perform any procedures can result in personal injury or equipment damage Some circuitry on the board can continue to operate even though the front panel power button is off Follow these guidelines before you begin e Always follow the steps in each procedure in the correct order e Setup a log to record information about your computer such as model serial numbers installed options and configuration information e Electrostatic discharge ESD can damage components Perform the procedures described in this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam pad If such a station is not available you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis Installation Precautions When you install and test the Inte2. clips are firmly in place C Intel NUC Kit NUCSPGYH User Guide Close the Chassis After all components have been installed close the Intel NUC chassis Intel recommends this be done by hand with a screwdriver to avoid over tightening and possibly damaging the screws Attach and Use the VESA Bracket Optional Follow these instructions to attach and use the VESA mount bracket 1 Using the four small black screws that were included in the box attach the VESA bracket to the back of the monitor or TV Intel NUC Kit NUCSPGYH User Guide 2 Attach the two slightly larger black screws to the bottom chassis cover of the Intel NUC 3 Slide the Intel NUC onto the VESA mount bracket Set Up Microsoft Windows 10 Microsoft Windows 10 is already installed on the Intel NUC Kit NUCSPGYH The first time you start the computer you are guided through the following Setup steps Select your region and language Accept the Microsoft Windows license terms Personalize Windows and assign a PC Name Get Online dialog to pick a wireless network this step is optional Choose Express Settings or Customize Assign a User Name and Password Finished oo eS a Intel NUC Kit NUCSPGYH User Guide Keep BIOS and Drivers Current To download the latest BIOS and drivers go to Download Center Refer to BIOS Update Instructions for information on updating the BIOS for your Intel NUC Drivers are available for the followin
3. g features e Audio e Bluetooth e Chipset e Consumer Infrared e Graphics e Intel TXE e Intel Ready Mode Technology e LAN wired and wireless e NFC e Serial I O e USB 3 0 Operating System Recovery There is a Windows recovery partition on the Intel NUC You can use this partition to Refresh Reset or Restore Windows Here is what each of these actions do Restore If your PC isn t performing as well as it once did and you don t know why you can refresh your PC This action does not delete any of your personal files or change your settings Refresh does the following Files and personalization settings won t change PC settings are changed back to their defaults Apps from the Windows Store are kept Apps installed from disks or websites are removed List of removed apps is saved on the desktop If you want to recycle your PC give it away or start over with it you can reset it completely This process removes everything Reset does the following e All personal files and apps are removed PC settings are changed back to their defaults e Windows is reinstalled If a recently installed app or driver is causing problems with your PC you can restore Windows back to an earlier point in time called a restore point System Restore doesn t change your personal files but it can remove recently installed apps and drivers Caution Before performing a reset or refresh e Make sure to back up all perso
4. l NUC observe all warnings and cautions in the installation instructions To avoid injury be careful of e Sharp pins on connectors e Sharp pins on circuit boards e Rough edges and sharp corners on the chassis e Hot components such as SSDs processors voltage regulators and heat sinks e Damage to wires that could cause a short circuit Observe all warnings and cautions that instruct you to refer computer servicing to qualified technical personnel Observe Safety and Regulatory Requirements If you do not follow these instructions you increase your safety risk and the possibility of noncompliance with regional laws and regulations Intel NUC Kit NUCSPGYH User Guide This guide tells you how to e Install a 2 5 drive optional e Upgrade memory optional e Install a VESA mount bracket optional e Setup Microsoft Windows 10 Keep BIOS and drivers current e Operating system recovery Install a 2 5 SSD or Hard Drive Optional For a list of tested 2 5 hard drives go to the Tested Peripherals page on the Support site Follow these instructions to install a 2 5 Solid State Drive SSD or Hard Disk Drive HDD 1 Observe the precautions in Before You Begin on page 2 2 Open the Intel NUC chassis by unscrewing the four corner screws on the bottom cover of the chassis and lift the cover Intel NUC Kit NUCSPGYH User Guide 3 Slide the 2 5 drive into the drive bay ensuring the SATA connectors a
5. nal data to external storage e Remove SD card from the card slot if one is inserted Intel NUC Kit NUCSPGYH User Guide To access the recovery media If Windows starts If Windows does not start From Windows Start type Recovery and select Recovery Options See Recovery options in Windows 10 for complete details on how to use the recovery options The recovery process should automatically start If Recovery does not automatically start you can try to initiate it as follows 1 Press F8 during boot when you see the prompt F8 to Activate Windows 8 1 10 Recovery Mode 2 Follow the recovery steps
6. re fully seated into the connectors of the SATA daughter card A 5 Set the drive bay bracket down inside the chassis C taking care not to pinch the SATA cables along the edge Intel NUC Kit NUCSPGYH User Guide Upgrade Memory Intel NUC Kit NUC5PGYH has a 2GB DDR3L memory module already installed You can upgrade to a larger capacity module if you wish Memory requirements e 1 35V low voltage memory e 1066 MHz or 1600 MHz SO DIMMs 1333 MHz modules will operate at 1066 MHz e Non ECC e Max memory 8GB For a list of tested memory go to the System Memory page on the Support site To upgrade memory 1 Remove the pre installed SO DIMM following these steps a Observe the precautions in Before You Begin on page 2 b Gently spread the retaining clips at each end of the SO DIMM socket The SO DIMM pops out of the socket c Hold the SO DIMM by the edges lift it away from the socket and store it in an anti static package d Reinstall and reconnect any parts you removed or disconnected to reach the SO DIMM sockets e Replace the computer s cover and reconnect the AC power cord 2 Install the new SO DIMM following these steps a Align the small notch at the bottom edge of the SO DIMM with the key in the socket A Insert the bottom edge of the SO DIMM into the socket c When the SO DIMM is inserted push down on the outer edge of the SO DIMM B until the retaining clips snap into place Make sure the
Download Pdf Manuals
Related Search