USER`S MANUAL
Contents
1. D Verify that the UTP LK ACT LEDs light when cable connection is installed correctly Verify that Fiber LK ACT LED blinks to indicate network activity Fiber 1000Base SX 10 100 1000 SPD PWR Gigs O Oi m o eem qt LK ACT IP Giga Fibei Converter FoX coL Multi Mode 10 100 1000 SPD PWR Gia O O w aK qt LK ACT IP n Giga Fiber Converter Multi Mode FDX COL UTP UTP 1000Base T 1000Base T 1000Base T Port 1000Base T Port RJ 45 connector RJ 45 connector on switch workstation on switch workstation Installing Converters into Chassis Follow the steps below to install modular converters into the 10 space Converter Chassis pn FEP 593110 A Remove the blank bracket from the chassis by rotating screw counterclockwise Put the blank bracket aside B Open the rack mount bracket kit The kit contains two rack mount brackets and four screws C Use a screwdriver to attach the rack mount ears to both sides of the modular converter D Install the modular converter by inserting it into the chassis guides and sliding it in until it stops Press it firmly to seat the chassis power plug into the modular converter receptacle E Gently push the thumbscrews in and turn clockwise to tighten Do not over tighten2. RJ 45 port There are six diagnostic LEDs located on the front panel of the connections The cable between the converter and the link partner converter They provide real time information of system and optional switch hub workstation etc must be less than 100 meters 328 status The following table provides descriptions of the LED status ft long LED D t Mode fiber cable Maximum distance between two devices using arale ha the SM fiber link is 10 Kilometers in full duplex operation For half PWR On Green e The converter is supplied with Suitable power duplex operation the recommended maximum distance is 412 e The Multi Mode Fiber segment must use 50 or 62 5 125um Multi cee EEEE e Current UTP Speed is 1000 Mbps meters 1352 ft Mode fiber cable Maximum distance between two devices using LK ACT Unit is connected with a link the Fiber link is 220m with 62 5 125 fiber and 550m with 50 125 UTP ae Unit is transmitting receiving data Off No device attached Troubleshooting LK ACT On Unit is connected with a fiber link e Verify that you are using the correct power adapter DC 9V O 7A re pune ee Bene ane TEGENE galg Do not use a power adapter with DC output greater than 9V as off No device attached converter damage may occur FDX COL On The UTP port is in full duplex mode e Check the configuration DIP switch It must be configured in the UTP Blinking Packet Collisions occurring in the port Same operation mode as its link
3. DI MDIX which is basically an auto crossover feature This means you can connect to another Switch or workstation without changing to a crossover cable e Fiber Port This port is for the 1000Base SX LX connection and is available in either the Multi Mode SC or Single Mode SC format Optical Fiber Spec The following table shows the optical fiber specification es ee l Wavelength 1310 nm Fiber Size 8 125yu 9 125u Output Optical Min 9 5 Max 3 dBm Stressed Receiver Max 13 5 dBm Avg Max 14 4 dBm Avg Sensitivity Max Fiber 62 5 125u 220m Distance 50 125u 550m Product Specifications Standard Compliance IEEE 802 3ab 1000Base T IEEE 802 3z 1000Base SX LX standard IEEE802 3x Flow Control and Back pressure Connectors Fiber SC SC Multi mode and Single Mode RJ 45 Port Cat5e 6 1000Mbps Twisted Pair cable Auto MDI MDIX and Auto Negotiation Function Support Fiber Parameters Fiber Core and Distance MM 62 5 125um 220m 50 125um 550m SM 8 125um 9 125um 10Km Wavelength 850nm MM 1310nm SM Transparent Packet 064 to 1536 Bytes for Ethernet packets Link Loss Forwarding UTP Fiber If UTP link is down then converter will force fiber link down Fiber UTP If Fiber link is down then converter will force UTP link down DIP Switch DIP Switch 1 UTP Fiber LLF Enable Disable DIP Switch 2 Fiber UTP LLF Enable Disable Cabling LED Indicators e Use four pair UTP Category 5e or 6 cabling for
4. NEW Lifetime For full coverage of your warranty be sure to register your product using the enclosed registration card A Network Systems Solution i C A M i 908 Canada Court City of Industry CA 91748 U S A Phone 626 964 7873 or 800 346 6668 Fax 626 964 7880 www unicomlink com e mail info unicomlink com UNICOM 2005 UNICOM and A Network Systems Solution are trademarks of UNICOM Electric Inc All rights reserved Specifications subject to change without notice Rev 04 05 A Network Systems Solution UNICOM 1000Base T to 1000Base SX LX Gigabit Ethernet Converter GEP S5001TF C 1000Base T SX SC MM 220 500m GEP 5101TF C 1000Base T LX SC SM 10Km User s MANUAL Package Contents Package contents include the following 1000Base T to 1000Base SX LX Converter MM or SM DC Power Adapter Rack Mount Brackets User s Manual Warranty card not shown Gigabit Converter User s Manual Power Adapter Rack Mount Converter Brackets Multi Mode or Single Mode IMPORTANT If any piece is missing or damaged please contact your local dealer or reseller for service For Your Records Product Name Serial Number Date of Purchase Purchased from Notes FCC Statement This equipment has been tested and found to comply with the limits for a class B device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable pro
5. one Ethernet RJ 45 port Auto MDI MDIX for 1000Base T copper cable connections DIP switches on the converter configure the operation modes for UTP Fiber ports and the link loss forwarding function Key Features Complies with IEEE 802 3 802 3u and 802 3x IEEE 802 3ab 1000Base T IEEE 802 3z 1000Base SX LX standard Converts between UTP cabling and Fiber optic cabling One RJ 45 connector supports 1000Mbps for UTP port One fiber connector SC MM or SC SM for LOOOBase SX LX Fiber cabling connectivity up to 10Km DIP Switches set the operation mode and Link Lost Forwarding function m LEDs Per port 1000 Link Activity Full Collision Per Unit Power m External DC power adapter 9V 0 7A m FCC Class A CE UL and CUL Mark certification m Can be mounted in chassis or used as stand alone Hardware Description The Front Panel The Front Panel of the 1000T SX LX converters consists of one RJ 45 Port Auto MDI MDIX Six LED Indicators 1000 LK ACT FDX Fiber LK ACT and PWR and one fiber 1000Base SX LX Port 1000Base T 1000 PWR 1000Base SX O O TX RX O O olo ie LK ACT zal FDX COL Auto MDI MDIX Multi Mode Multi mode 1000Base T 1000 PWR 1000Base LX O O 7X RX O O de LK ACT Auto MDI MDIX i FDX COL z Single Mode Single Mode Ports e RJ 45 Port Auto MDI MDIX the Ethernet RJ 45 features a 1000Base T connection and Auto M
6. partner Off Half duplex mode no device attached e Verify that you are using the correct cable e Do not combine Multi Mode and Single Mode devices Status Description ON UTP LLF Enable OFF UTP LLF Disable ON Fiber LLF Enable OFF Fiber LLF Disable The DIP Switch is used to configure operation mode for LLF Link Lost Forwarding and operation mode for the UTP Fiber ports The default value of the dipswitch is OFF Link Lost Forwarding When LLF is enabled UTP link failures are reported to the fiber side and Fiber link failures are reported to the UTP side Therefore A link loss forward feature is provided for both UTP and Fiber operations Note Do not change the DIP switch settings when the UTP or fiber ports are transmitting or receiving data This may cause data errors Rear Panel The rear panel contains a power socket This power socket accepts DC 9V voltage and minimum 7OOmA supplied current Network Connection A Select the appropriate length Category 5e or 6 twisted pair cable Connect one end of the twisted pair cable to the RJ 45 connector on the converter and the other end of twisted pair cable to the RJ 45 connector on any 1000Base T device B Connect one end of a fiber jumper to the SC connector on this converter and the other end of the fiber jumper to the SC connector on the other 1000Base SX LX device C Attach the power adapter DC jack to the converter Verify that the Power LED is on
7. tection against harmful interference in a commercial installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with instructions may cause harmful interference with radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user s expense 10 LED Indicators Power EMI Enclosure Dimensions Warranty Power UTP 1000Mbps LK Act FDX COL Fiber LK Act FDX COL Stand alone external adapter 9V DC 0 7A FCC Class A CE UL CUL Metal 4 75 L x 3 4 W x 96 H 119mm x 85mm x 26mm Limited Lifetime Introduction Congratulations on purchasing a quality UNICOM product Unicom s VELOCITY Series represents the newest most advanced generation of signal conversion technology The Gigabit Fiber Converter Module is a cost effective solution for the conversion of 1000Base T to 1000Base SX LX cabling and can be used in Unicom s 10 bay media chassis or as stand alone component The Gigabit Fiber Converter Module extends the cabling distance of your 1000Base T network up to 550m with Multi mode or 10Km with Single Mode fiber optic cabling The Gigabit Fiber Converter provides the most popular fiber cabling connection the SC connector The Gigabit Fiber Converter features one fiber connector for fiber optic cable and
Download Pdf Manuals
Related Search