USER MANUAL
Contents
1. Adjustment Item Problem Option Button to Press VGA Select the VGA input DVI Select the DVI input Input Select Auto Search for an available input source and select automatically Ney Input source is fixed not selected automatically when VGA and DVI which are selected You can skip the Menu items and display an adjustment scale directly by using the following button operations Input Select Press the Button when the Menu is not displayed Audio Adjust Direct Audio Adjust Adjustment Item Problem Option Button to Press Vol Too soft di A Too loud V On Return the sound volume to the previous level Off Turn off the sound temporarily To activate the option mark it in the setup menu To deactivate it remove the marking You can skip the Menu items and display an adjustment scale directly by using the following button operations Audio Adjust Press the Button when the Menu is not displayed Mute Pressing and holding of the Button for about 2 seconds when the Menu is not displayed Mute and Unmute are switched as follows by pressing the A Button successively 12 OPERATING THE MONITOR Color Adjust Color Adjust Adjustment Item Problem Option Button to Press Cool Bluish white Normal Reddish white Warm Greenish white Red User Color Green E piae d Blue Off Ret2. 79 976kHz 75 025Hz 135 000MHz 24 APPENDIX M063A22
3. For example to correct for vertical position select Menu item of Manual Image Adjust and then press the Button Then select H V Position by using the W Buttons Auto Image Adjust Picture Adjust x H N Position Clock Phase Sharpness Audio Adjust J Video Mode Adjust Color Adjust Information Input Select Manual Image Adjust Setup Menu Memory Recall An adjustment page appears after you press the Button Then select V Position by using the W Buttons Press the Button again Then use the A W Buttons to change the vertical position settings The vertical position of the overall display should be changing accordingly while you are doing this Manual Image Adjust H N Position H Position 50 ul Position 0 1 50 Press the Button lastly it ends all changes are saved in the memory m When button operations are aborted during adjustment On Screen Display disappears when the time set for the OSD Time Out has passed Also the button can be used to return previous menu and turn off the On Screen Display W Any changes are automatically saved in the memory when the On Screen Display disappears Turning off the power should be avoided while using the Menu Adjustments for H V Position Clock and Phase are saved for each signal timing Except for these adjustments all other adjustments have only one setting which applies to all signal timings 10 OPERATING THE MO
4. The relevant national installation and or equipment regulations shall be considered A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 designation HO5VV F 3G 0 75mm or HO5VVH2 F2 3G 0 75mm shall be used Alternative a flexible cord be of synthetic rubber according to IEC 60245 designation HOBRR F 3G 0 75mm shall be used We recommend recycling of used product Please contact your dealer or iiyama service center Recycle information is obtained via the Internet using the address http www iiyama com You can access the Web page of different countries from there W We reserve the right to change specifications without notice W All trademarks used in this user manual are the property of their respective owners W As an ENERGY STAR Partner iiyama has determined that this product meets the ENERGY STAR guidelines for energy efficiency ENGLISH ENGLISH TABLE OF CONTENTS 5 1 SAFETY PRECAUTIONS i e ete e nec ed eee t s 1 SPECIAL NOTES ON LCD MONITORS creision 3 CUSTOMER SERVIGE 2 timete te err te n ede t t e a 3 CLEANING cote Ett ev Lee ttes aD Leon e P tA 3 BEFORE YOU OPERATE THE MONITOR 4 FEATURES 4 CHECKING THE CONTENTS OF THE 4 WALE MOUNTING ceret echt
5. It is recommended to operate at resolution of 1280 x 1024 in normal use Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to the screen enlargement process W t is preferable to adjust the image position and frequency with the monitor controls rather than the computer software or utilities W Perform adjustments after a warm up period of at least thirty minutes B Additional adjustments may be required after the Auto Image Adjust depending on the resolution or signal timing W The Auto Image Adjust may not work correctly when displaying the picture other than the screen adjustment pattern In this case manual adjustments are required There are two ways to adjust the screen One way is automatic adjustment for Position Horizontal Size and Fine Tune The other way is performing each adjustment manually Perform the Auto Image Adjust first when the monitor is connected to a new computer or resolution is changed If the screen has a flicker or blur or the picture does not fit in the display area after performing the Auto Image Adjust manual adjustments are required Both adjustments should be made by using the screen adjustment pattern Test bmp obtained via the IIYAMA website http www iiyama com Adjust the image by following the procedure below to get the desired picture This manual explains adjustment under Windows OS CD Display the picture at the optimum resolution Ent
6. Recall Before reporting the screen defect please Important prepare the following information evidence Note model number If there is no fault found in the collected equipment after inspection the transferring party shall incur charges for transport and administration purchase receipt and serial number name and address for collection telephone fax number for availability during the day fenicallectonidate aatent If you have checked all of the above and there is convenient collection date date time still no picture call our information line for assistance short description of the defect in your country see the identification plate on the back of the case www iiyama com li DECLARATION OF CONFORMITY This LCD monitor complies with the requirements of the EC EU Directive 2004 108 EC Directive 2006 95 EC Low Voltage Directive 2009 125 EC ErP Directive and 2011 65 EU RoHS Directive The electro magnetic susceptibility has been chosen at a level that gives correct operation in residential areas business and light industrial premises and small scale enterprises inside as well as outside of the buildings All places of operation are characterised by their connection to the public low voltage power supply system IIYAMA CORPORATION Wijkermeerstraat 8 2131 HA Hoofddorp The Netherlands A certified power supply cord has to be used with this equipment
7. display area after the Horizontal Size adjustment repeat steps from S 18 OPERATING THE MONITOR Adjust the Fine Tune to correct horizontal wavy noise flicker or blur in the zebra pattern W case the strong flicker or blurs remain on a part of the screen repeat steps 6 and 7 because the Horizontal Size may not be adjusted correctly If the flicker or blurs still remain set the refresh rate of computer to low 60Hz and repeat steps from 3 again W Adjust the H Position after the Fine Tune adjustment if the horizontal position moves during the adjustment Adjust the Brightness and Color Adjust to get the desired picture after you complete the Horizontal Size and Fine Tune adjustments Put back your favorite wallpaper OPERATING THE MONITOR 19 ENGLISH ENGLISH POWER MANAGEMENT FEATURE The power management feature of this product complies with power saving requirement of ENERGY STAR and VESA DPMS When activated it automatically reduces unnecessary power consumption of the monitor when your computer is not in use To use the feature the monitor needs to be connected to a VESA DPMS compliant computer There is a power management step the monitor takes as described below The power management function including any timer settings is configured by the operating system Check your operating system manual for information on how this can be configure
8. ree etr ERE DR 5 FITTING AND REMOVAL OF BASE rugni baai 6 CONTROLS AND CONNECTORS 7 CONNECTING YOUR 8 COMPUTER SETTING 1n ceret eoo teret era teer Perret 9 ADJUSTING THE VIEWING ANGLE 2 0 9 OPERATING THE MONITOR 10 ADJUSTMENT MENU CONTENTS 11 SCREEN ADJUSTMEN S inerte eto tnter ter ettet feras ted eerie 17 POWER MANAGEMENT FEATURE 120 TROUBLESHOOTING tnter rtr eet rre mist reete ten 21 REGYGLEING INFORMATION bei x tne tert rette bcne teet deett 22 APPENDIX SPECIFICATIONS DIMENSIONS COMPLIANT TIMING FOR YOUR SAFETY SAFETY PRECAUTIONS WARNING STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE If you notice any abnormal phenomena such as smoke strange sounds or fumes unplug the monitor and contact your dealer or iiyama service center immediately Further use may be dangerous and can cause fire or electric shock NEVER REMOVE THE CABINET High voltage circuits are inside the monitor Removing the cabinet may expose you to the danger of fire or electric shock DO NOT PUT ANY OBJECT INTO THE MONITOR Do not put any solid objects or liquids such as water into the monitor In case of an accident unplug your monitor immediately and contact your dealer or iiyama service center Using the monitor with any object i
9. routed such that children may not pull the cables and possibly cause injury MAINTAIN GOOD VENTILATION Ventilation slots are provided to keep the monitor from overheating Covering the slots may cause fire To allow adequate air circulation place the monitor at least 10 cm or 4 inches from any walls Do not remove the tilt stand when operating the monitor Ventilation slots on the back of the cabinet will be blocked and the monitor may overheat if the stand is removed This may cause fire or damage Operating the monitor on its back side upside down or on a carpet or any other soft material may also cause damage DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR When you move the monitor turn off the power switch unplug the monitor and be sure the signal cable is disconnected If you do not disconnect them it may cause fire or electric shock UNPLUG THE MONITOR If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid accidents HOLD THE PLUG WHEN DISCONNECTING To disconnect the power cable or signal cable always pull it by the plug Never pull on the cable itself as this may cause fire or electric shock DO NOT TOUCH THE PLUG WITH WET HANDS Pulling or inserting the plug with wet hands may cause electric shock WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER Be sure the computer is strong enough to hold the weight of the monitor otherwise you may damage your computer CARE TO AH
10. when using the monitor at visual display workstations it is recommended that the adjusted tilt angle should not exceed 10 degrees Adjust the monitor s angle to your own preference W Do not press down heavily on the glass when you change the angle It may cause damage or break the LCD screen W Careful attention is required not to catch your fingers or hands when you change the angle BEFORE YOU OPERATE THE MONITOR 9 ENGLISH ENGLISH OPERATING THE MONITOR To create the best picture your LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 24 You are also able to adjust the picture by following the button operation shown below For more detailed adjustments see page 17 for SCREEN ADJUSTMENTS Press the Button to start the On Screen Display OSD feature There are additional Menu items which can be switched by using the V Buttons Auto Image Adjust Picture Adjust Input Select Audio Adjust Color Adjust Information Manual Image Adjust Setup Menu Memory Recall Select the Menu item which contains the adjustment icon relating to the adjustment you want to make Press the Button Then use the A W Buttons to highlight the desired adjustment icon Press the Button again Use the V Buttons to make the appropriate adjustment or setting Press the Button to leave the menu and the settings you just made would be automatically saved
11. AND AND FINGERS W Careful attention is required not to catch your fingers or hands when you change the height or the angle W Injury can occur if care is not taken to avoid finger contact with the displays base when adjusting the height Just for height adjustable model DO NOT USE THE MONITOR FOR 24 HOURS CONTINUOUSLY The monitor is not designed to work for 24 hours continuously do not use the monitor for 24 hours continuously OTHERS ERGONOMIC RECOMMENDATIONS To eliminate eye fatigue do not operate the monitor against a bright background or in a dark room For optimal viewing comfort the monitor should be just below eye level and 40 60 cm 16 24 inches away from your eyes When using the monitor over a prolonged time a ten minute break every hour is recommended as looking at the screen continuously can cause eye strain 2 FOR YOUR SAFETY SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitors and do not indicate a problem m When you first turn on the LCD monitor the picture may not fit in the display area because of the type of computer that is used In this case adjust the picture position to the correct position W Due to the nature of the backlight the screen may flicker during initial use Turn off the Power Switch and then turn it on again to make sure the flicker disappears W You may find slightly uneven brightness on the screen depending on the desktop pattern you use W Due to the natu
12. NITOR ADJUSTMENT MENU CONTENTS Adjustment Item Problem Option Button to Press Auto Image Adjust Direct Adjust H V Position Clock and Phase automatically For best results use the Auto Image Adjust in conjunction with the adjustment pattern See page 17 for SCREEN ADJUSTMENTS You can skip the Menu items and display an adjustment scale directly by using the following button operations Auto Image Adjust Pressing and holding of the W Button for about 2 seconds when the Menu is not displayed Adjustment Item Problem Option Button to Press Too dull Contrast Too intense t V Brightness 23 Too HB Too bright t V Off Typical Contrast Ratio Adv Contrast On Increased Contrast Ratio Off Normal ECO Mode 1 Brightness of back light is reduced 2 Brightness of back light is reduced more than 1 3 Brightness of back light is reduced more than 2 Adjust the Brightness when you are using the monitor a dark room and feel the screen is too bright Can not select when Adv Contrast is On Brightness and Adv Contrast can not enable the same time when ECO Mode is on Contrast Brightness Adv Contrast and ECO Mode adjustments are disabled when i Style Color is activated activate the option mark it in the setup menu To deactivate it remove the marking OPERATING THE MONITOR 11 ENGLISH l ENGLISH
13. d W Power Management Mode When the H sync signal V sync signal H and V sync signals from the computer are off the monitor enters into Power Management Mode which reduces the power consumption to less than 0 5W The screen becomes dark and the power indicator turns to orange From Power Management Mode the image reappears in several seconds when either the keyboard or the mouse are touched again Power Indicator NORMAL MODE gt Blue POWER MANAGEMENT MODE 4 POWER 0 0 5W 100 CONSUMPTION W Even when using the power management mode the monitor consumes electricity Turn off the Power Switch whenever the monitor is not in use during the night and weekends to avoid unnecessary power consumption E It is possible that the video signal from the computer may be on while the or V sync signal is missing In this instance the POWER MANAGEMENT feature may not work properly 20 OPERATING THE MONITOR TROUBLE SHOOTING If the monitor fails to operate correctly please follow the steps below for a possible solution 1 Perform the adjustments described in OPERATING THE MONITOR depending on the problem you have If the monitor does not get a picture skip to 2 2 Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists 3 If you are experiencing a problem which is not described below or you cannot correct the prob
14. degeneration or loss of paint on the cabinet CABINET Stains can be removed with a cloth lightly moistened with a mild detergent solvent Then wipe the cabinet with a soft dry cloth LCD Periodic cleaning with a soft dry cloth is recommended SCREEN Don t use tissue paper etc because these will damage the LCD screen FOR YOUR SAFETY 3 i ENGLISH ENGLISH BEFORE YOU OPERATE THE MONITOR FEATURES Supports Resolutions up to 1280 x 1024 High Contrast 1000 1 Typical Adv Contrast Function Available Brightness 240cd m Typical Quick Response Time 5ms Black White Black Digital Character Smoothing Automatic Set up Stereo Speakers 2 x 1W Stereo Speakers Plug amp Play VESA DDC2B Compliant Windows XP Vista 7 8 Compliant Power Management ENERGY STAR VESA DPMS Compliant VESA Mounting Standard 100mmx100mm Compliant Keyhole for Security Lock CHECKING THE CONTENTS OF THE PACKAGE The following accessories are included in your package Check to see if they are enclosed with the monitor If anything is missing or damaged please contact your local dealer or regional iiyama office Power Cable W VGA D sub Signal Cable DVI D Cable Audio Cable E Stand Base W Safety Guide Quick Start Guide The rating of the Power Cable enclosed 120V area is 10A 125V If you are using a power supply higher than this rating then a power cable with a rating
15. e audio features Connect the Power Cable to the monitor first and then to the power supply 5 Power of the monitor and the computer is turned on W The signal cables used for connecting the computer and monitor may vary with the type of computer used An incorrect connection may cause serious damage to both the monitor and the computer The cable supplied with the monitor is for a standard connector If a special cable is required please contact your local iiyama dealer or regional iiyama office W For connection to Macintosh computers contact your local dealer or regional iiyama office for a suitable adaptor W Make sure you tighten the finger screws at each end of the signal cable Example of Connection Back 5 Power Cable Accessory VGA D sub Signal Cable Accessory DVI D Cable Accessory UG gt Audio Cable Accessory Computer 8 BEFORE YOU OPERATE THE MONITOR COMPUTER SETTING m Signal Timing Change to the desired signal timing listed on page 24 COMPLIANT TIMING ADJUSTING THE VIEWING ANGLE W For optimal viewing it is recommended to look at the full face of the monitor m Hold the stand so that the monitor does not topple when you change the monitor s angle W You are able to adjust the monitor s angle up to 20 degrees upward order to ensure a healthy and relaxed body position
16. e table beforehand to prevent the monitor from being scratched Lay the monitor flat on a table with front face down Press and hold the hook outside and slide the stand base to the front of the monitor C and pull the stand base from the monitor D 6 BEFORE YOU OPERATE THE MONITOR CONTROLS AND CONNECTORS Front Back 9 7 9 2 i amp rum E di 12 Power Switch 05 Power Indicator Blue Normal operation Orange Power Management 2 Select Input select Button 2p 8 Scroll up Audio Adjust Button 4 Scroll Down i Style Color Button W Menu Button 1 6 Speakers 7 VGA D sub mini 15pin Connector VGA DVI D 24pin Connector DVI 9 Audio Connector AUDIO Keyhole for Security Lock You can fasten a security lock and cable to prevent the monitor from being removed without your permission AC Connector AC BEFORE YOU OPERATE THE MONITOR 7 ENGLISH i ENGLISH CONNECTING YOUR MONITOR CD Ensure that both the computer and the monitor are switched off 2 Connect the computer to the monitor with the signal cable Connect the monitor to the audio equipment with the Audio Cable for computer when using th
17. er the Test bmp screen adjustment pattern to wallpaper mConsult the appropriate documentation for doing this WTest bmp is made at resolution of 1280 1024 Set the display position to center in the wallpaper setting dialogue box Adjustment pattern OPERATING THE MONITOR 17 ENGLISH I ENGLISH Press the Button Auto Image Adjust 4 Adjust the image manually by following procedure below when the screen has a flicker blur or the picture does not fit in the display area after performing the Auto Image Adjust 5 Adjust the V Position so that the top and bottom of the picture frame will fit to the display area 1 Adjust the H Position so that the left side of the picture frame will move to the left edge of the display area 2 Stretch the right side of the picture frame to the right edge of the display area by adjusting the Horizontal Size W When the left side of the picture frame moves apart from the left edge of the display area during the Horizontal Size adjustment adjust steps 1 and 2 W Another way to make the Horizontal Size adjustment is to correct the vertical wavy lines in the zebra pattern W The picture may flicker during the Horizontal Size H Position and V Position adjustment W n case the picture frame is bigger or smaller than the data
18. he monitor O The power voltage is within the specification of the monitor O The signal timing of the computer is within the specification of the monitor TROUBLE SHOOTING 21 ENGLISH Problem Check 6 No sound O The audio equipment computer etc is ON L1 The Audio Cable is properly connected L1 The Volume is turned up O The Mute is OFF L1 The audio output level of the audio equipment is within the specification of the monitor 7 The sound is too O The audio output level of the audio equipment is within the specification of loud or too quiet the monitor A strange noise O The Audio Cable is properly connected is heard RECYCLING INFORMATION For better environment protection please don t dispose your monitor Please visit our website www iiyama com recycle for monitor recycling 22 TROUBLE SHOOTING RECYCLING INFORMATION APPENDIX Design and specifications are subject to change without prior notice SPECIFICATIONS 19 TN Diagonal 19 48cm 0 294mm H x 0 294mm V 240 Typical 1000 1 Typical Adv Contrast Function Available Right Left 85 degrees each Up Down 80 degrees each Typical 5ms Black White Black Approx 16 7M Horizontal 30 0 80 0kHz Vertical 55 75Hz 1280 x 1024 1 3 MegaPixels D Sub mini 15 pin DVI D 24 pin VESA DDC2B Separate sync TTL Positive or Negative Analog 0 7Vp p Standard 750 Positive Digital DVI Digital Visual Interface S
19. iiyama USER MANUAL Pro Lrte LCD Monitor Prolrte 19055 Thank you very much for choosing the iiyama LCD monitor We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor Please keep this manual in a safe place for your future reference e ENERGY STAR Servicecard 3 9 50 paN Dear user we congratulate you on the purchase of your iiyama LCD For details on warranty and locally used pixel policies that apply directly after installation of your product please check the website To report a fault please contact your local support centre found at www iiyama com service Things to check before you call the iiyama information line if the power cable is connected securely and turned on if the display has been turned on if the signal cable is connected securely and the correct input selected if the computer has been restarted with the display connected if the graphics card is correctly installed with the latest drivers possible if the correct native resolution has been selected via Display Properties If the R G B signal configuration is correct if the displays On Screen Menu is shown if the correct brightness and contrast settings have been set if given display tolerances and compatibility have been considered if via the On Screen Menu you have performed a Factory Reset
20. lem discontinue using the monitor and contact your dealer or iiyama service center for further assistance Problem D The picture does not appear Power indicator does not light up Power indicator is blue Power indicator is orange The screen is not synchronized The screen position is not in the center 4 The screen is too bright or too dark 5 The screen is shaking Check ENGLISH L1 The Power Cable is firmly seated in the socket L1 The Power Switch is turned ON O The AC socket is live Please check with another piece of equipment oO If the blank screen saver is in active mode touch the keyboard the mouse Increase the Contrast and or Brightness O The computer is ON O The Signal Cable is properly connected O The signal timing of the computer is within the specification of the monitor O If the monitor is in power management mode touch the keyboard or the mouse O The computer is ON O The Signal Cable is properly connected O The signal timing of the computer is within the specification of the monitor L1 The Signal Cable is properly connected O The signal timing of the computer is within the specification of the monitor O The video output level of the computer is within the specification of the monitor O The signal timing of the computer is within the specification of the monitor O The video output level of the computer is within the specification of t
21. nside may cause fire electric shock or damage INSTALL THE MONITOR ON A FLAT STABLE SURFACE The monitor may cause an injury if it falls or is dropped DO NOT USE THE MONITOR NEAR WATER Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric shock OPERATE UNDER THE SPECIFIED POWER SUPPLY Be sure to operate the monitor only with the specified power supply Use of an incorrect voltage will cause malfunction and may cause fire or electric shock PROTECT THE CABLES Do not pull or bend the power cable and signal cable Do not place the monitor or any other heavy objects on the cables If damaged the cables may cause fire or electric shock ADVERSE WEATHER CONDITIONS It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in power may cause malfunction It is also advised not to touch the plug in these circumstances as it may cause electric shock FOR YOUR SAFETY 1 I ENGLISH I ENGLISH CAUTION INSTALLATION LOCATION Do not install the monitor where sudden temperature changes may occur or in humid dusty or smoky areas as it may cause fire electric shock or damage You should also avoid areas where the sun shines directly on the monitor DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION The monitor may topple and cause injury if not suitably located Please also ensure that you do not place any heavy objects on the monitor and that all cables are
22. of 10A 250V must be used However all guarantees and warranties are void for any problems or damage caused by a power cable not supplied by iiyama 4 BEFORE YOU OPERATE THE MONITOR WALL MOUNTING WARNING W When you use with the wall mounting in consideration of thickness of the mounting stage tighten the M4 Screw with washer which L length is 7mm to fasten the monitor Using the screw longer than this may cause electric shock or damage because it may contact with the electrical parts inside the monitor W Please check if the wall or ceiling can support the weight of the monitor before mounting it Screw Mounting Stage L Chassis BEFORE YOU OPERATE THE MONITOR 5 ENGLISH FITTING AND REMOVAL OF BASE W Put the monitor on a stable surface The monitor may cause injury or damage if it falls or is dropped W Do not give a strong impact to the monitor It may cause damage W Unplug the monitor before removal or installation to avoid electric shock or damage Installation D Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched Lay the monitor flat on a table with front face down Install the stand base to the monitor A and slide the stand base to the back of the monitor B Jj ENGLISH Removal D Put a piece of soft cloth on th
23. quality from 0 to 3 soft to sharp Sharpness Press the A Button to change the picture quality in numerical order Press the W Button to change the picture quality in reverse numerical order Adjust the picture quality at resolutions of less 1280 x 1024 You can change the picture quality 4 steps Only Analog Input See page 16 for SCREEN ADJUSTMENTS 14 OPERATING THE MONITOR Adjustment Item Problem Option Button to Press English English Russian Frangais French HAG Japanese Language Select Deutsch German f tk amp Px Simplified Chinese Nederlands Dutch srt sc Traditional Chinese Polski Polish 4 OSD is too left H Position OSD is too right e V OSD Position V Positi OSD is too low a A osion OSD is too high v OSD Ti Out You can set the OSD display duration time amp 5 15 30 60 seconds Y On The background of OSD is mode transparent OSD Background Off Retune the background of OSD On Logo displayed when the monitor is turned on Opening Logo Off Logo does not display when the monitor is turned on LED On The Power Indicator is turned On Off The Power Indicator is turned Off Turn Off the Power Indicator when you are bothered by the light To activate the option mark it in the setup menu To deactivate it remove the marking Memory Recall 49 Memor
24. re of the LCD screen an afterimage of the previous screen may remain after switching the image when the same image is displayed for hours In this case the Screen is recovered slowly by changing the image or turning off the Power Switch for hours B Contact your dealer or iiyama service center for the backlight replacement when the screen is dark flickering or not lighting up Never attempt to replace it by yourself CUSTOMER SERVICE m The fluorescent light used in the LCD monitor may have to be periodically replaced For the warranty coverage on this component please check with local service center W f you have to return your unit for service and the original packaging has been discarded please contact your dealer or iiyama service center for advice or replacement packaging CLEANING B If you drop any materials or liquids such as water into the monitor when cleaning unplug the power cable immediately and contact your dealer or iiyama service center Aei m For safety reasons turn off the power switch and unplug the monitor before you clean it Alezi To protect the LCD panel do not scratch or rub the screen with a hard object W Never use any of the following strong solvents These will damage the cabinet and the LCD screen Thinner Spray type cleaner Benzine Wax Abrasive cleaner Acid or Alkaline solvent W Touching the cabinet with any product made from rubber or plastic for a long time may cause
25. tandard Rev 1 0 compliance 0 3 5mm mini jack Stereo 1 0Vrms maximum 1W x 2 Stereo speakers 376 320mm W x 301 056mm H 14 8 W x 11 9 H 100 240VAC 50 60Hz 0 6A 16W typical Power management mode 0 5W maximum 414 5x 420 5 x 200 5mm 16 3 x 16 6 x 7 9 WxHxD 4 6kg 10 14lbs Upward 20 degrees Operating Temperature 5 to 35 41 to 95 F Humidity 10 to 8096 No condensation Storage Temperature 20 to 60 4 to 140 F Humidity 5 to 8596 No condensation CE T V GS CU Energy Star Audio equipment is not connected APPENDIX 23 ENGLISH ENGLISH _ 200 5mm 7 89 414 5mm 16 3 378 0mm 14 9 70 5mm 2 78 e EE E CIEN 5 9 201 5mm 7 93 COMPLIANT TIMING Video Mode Horizontal Vertical Dot Clock Frequency Frequency 31 469kHz 59 940Hz 25 175MHz VGA 640x480 37 500kHz 75 000Hz 31 500MHz 37 861kHz 72 809Hz 31 500MHz 35 156kHz 56 250Hz 36 000MHz 37 879kHz 60 316Hz 40 000MHz SVGA 800x600 72 188Hz 50 000MHz VESA 46 875kHz 75 000Hz 49 500MHz 48 363kHz 60 004Hz 65 000MHz XGA 1024x768 56476kHz 70 069Hz 75 000MHz 60 023kHz 75 029Hz 78 750 2 63 981kH 60 020H SXGA 1280 1024
26. urn to a state set by color adjustment except i Style Color Standard For general windows environment and monitor default setting i Style Color Direct Game For PC game environment Cinema For movie and video environment Scenery For displaying outdoor scenery images Text For text editing and viewing in a word processing environment You can skip the Menu items and display an adjustment scale directly by using the following button operations i Style Color Press the W Button when the Menu is not displayed Information B Information lt Example gt Resolution H Frequency V Frequency Pixel Clock Model Number 1280x1024 64 00KHz 60 0Hz 108 0MHz GELI Displays information regarding the current input signal coming from the graphic card in your computer See your graphic card user guide for more information about changing the resolution and refresh OPERATING THE MONITOR 13 ENGLISH Jj ENGLISH Manual Image Adjust EJ Manual Image Adjust Adjustment Item Problem Option Button to Press H Position Ton len Too right e V H V Position V Position 108 low A Too high V Clock Too narrow Too wide V 1 pees A Phase To correct flickering text or lines amp 0123 yv You can change the picture
27. y Recall Adjustment Item Problem Option Button to Press Memory Recall Factory preset data is restored OPERATING THE MONITOR 15 ENGLISH ENGLISH e Lock Mode OSD Menu 1 The OSD lock will be activated by pressing the front buttons and for about 10 seconds If you try to access the OSD by pressing any of the buttons V and message OSD Locked will appear on the screen 2 The OSD lock will be deactivated by pressing the front buttons and again for 10 seconds Power Switch 1 The power switch lock will be activated by pressing the front buttons and W for 10 seconds Locking the power switch means that won t be able to turn off the Monitor while the power switch is locked If presses the power switch message Power Button Locked will appear on the screen 2 The power switch lock will be deactivated by pressing the front buttons and W again for about 10 seconds 16 OPERATING THE MONITOR SCREEN ADJUSTMENTS Adjust the image by following the procedure below to get the desired picture when selecting Analog input W The screen adjustments described in this manual are designed to set image position and minimize flicker or blur for the particular computer in use W The monitor is designed to provide the best performance at resolution of 1280 x 1024 but can not provide the best at resolutions of less than 1280 x 1024 because the picture is automatically stretched to fit the full screen
Download Pdf Manuals
Related Search