Fagor 1FET-211 W User Guide Pdf - WashingMachine
Contents
1. e CLEANING THE MACHINE Important To clean the casing the control panel and all the plastic parts in general use a sponge or a soft cloth dampened only with water and liquid soap In all cases do not use Abrasive powders Metal or plastic sponges Alcohol based products alcohol thinners etc e CARE OF THE INTERNAL COMPONENTS To ensure better hygiene we recommend that you Leave the lid open for a short time after washing Clean the plastic and rubber access components to the tank approximately once a month using a slightly chlorinated product Run a rinsing cycle to remove any residue of this product Run a washing cycle at 90 C at least once a month CLEANING THE PRODUCTS BOX Clean the products box regularly To do this Press the bosses on each side of the box simultaneously to extract it from its housing Diagram D24 Remove the siphons from the rear of the box and separate the box from its front cover Diagram D25 Rinse everything under the tap taking care to empty any excess water remaining inside the box Refit all the box components ensuring that the box section itself is properly clipped into the cover and then re insert the complete assembly into its location under the machine s lid PERIODIC CHECKS To avoid any water damage we recommend that you regularly check the condition of the water and drain hoses If you notice the slightest2. either your dealer or another qualified mechanic who is an authorized agent for the brand appliances When making an appointment state the complete reference of your equipment model type and serial number This information appears on the manufacturer s nameplate attached to the rear of the equipment Downloaded From WashingMachine Manual com Manuals e MESSAGES INDICATED BY THE VARIOUS LIGHTS FLASHING e Incidents indicated which you can rectify yourself In this section we explain how you can rectify these incidents very easily yourself Your machine automatically detects some operating incidents and indicates these by particular options lights flashing Lights flashing Causes Remedies The water tap is closed Check that the water tap Mae is open and then press the button again to restart the cycle This incident may also be caused by the drain hose being poorly connected see the section DRAINING AWAY THE WASTE WATER The pump filter is clogged Clean the pump filter for how to do this see the section CLEANING THE PUMP FILTER and then press the Start Pause button again to restart the cycle Also check the drain hose s position in the drain the connection must not be airtight see the section DRAINING AWAY THE WASTE WATER ZAS Drain hose not positioned properly Check the drain hose s position in the drai
3. cracking do not hesitate to replace the hoses with identical ones available from the manufacturer or his After Sales Service For how to replace the water supply hose please refer to the section CONNECTING TO THE COLD WATER SUPPLY e REPLACING THE POWER SUPPLY CABLE Warning For your safety the power cable and depending on the model the complete electric box and its associated cable must only be replaced by the manufacturer s After Sales Service or a qualified electrician 6 INCIDENTS AND MEANING OF PARTICULAR LIGHTS FLASHING e INCIDENTS THAT MAY OCCUR e The cycle does not start You have not pressed the Start Pause button There is no power to the machine Check that the plug is correctly in the socket Check the circuit breaker and the fuses The water tap is closed The machine s lid is not closed properly e A puddle of water forms around the machine Warning First of all remove the plug and the fuse and shut off the water supply tap While the machine is operating the permanent level control prevents the water from overflowing If despite this water comes out of your machine it may be that The drain hook is wrongly positioned in the drain pipe The water supply hose is not sealed tightly at the machine or tap end Check that the seals are in place and the connections are tight e Heavy vibration during spin All the transport materials have not been removed corr
4. rane a estetick parametry D le it P ed prvn m uveden m va eho p stroje do provozu si pe liv p e t te tento n vod k instalaci a k pou it pro rychlej sezn men se s jeho funkcemi W ramach statego poprawiania naszych produkt w zastrzegamy sobie prawo do wprowadzania zmian rozwojowych w ich charakterystyce technicznej funkcjonalnej lub estetyce Wa na uwaga Przed uruchomieniem urz dzenia nale y uwa nie przeczyta instrukcj instalacji i obstugi aby zapozna sie jak najszybciej z jego dzia aniem 35 Oldal 43 Term keink lland fejleszt se rdek ben fenntartjuk a jogot hogy fejl d shez kapcsol d technikai m k d si a vagy eszt tikai jellemz ket megv ltoztassuk Fontos Miel tt haszn ln a mos g pet figyelmesen olvassa el ezt az
5. base of the machine Diagram D12 D 3 PREPARING YOUR WASHING AND YOUR MACHINE CONNECTING TO THE ELECTRICITY SUPPLY Important For your safety you must comply with the instructions below Before connecting your machine you must ensure that your installation s electrical characteristics match those of your machine see the details provided on the information plate affixed to the back of the machine The electrical installation must comply with the prevailing standards and the Electricity Board s regulations in the country concerned particularly as regards Earthing and installation in shower rooms We cannot be held responsible for any incident caused by the machine being incorrectly earthed Advice Advice on the electrical installation of your machine Do not use an extension lead adapter or multiple socket Never cut out the Earth wire The socket must be readily accessible but out of the reach of children If in any doubt please contact your installer Important Your machine conforms to European Directives EEC 73 23 Low Voltage Directive and EEC 89 336 Electromagnetic Compatibility as modified by Directive EEC 93 68 e INSTALLING YOUR MACHINE Important If you are installing your machine next to another machine or a unit we recommend that you leave a gap between them to allow for air circulation Advice We also strongly recommend that you do NOT Install
6. is permanently lit you can programme a new cycle without having to reset the selector to the position For this all you have to do is turn one of the selectors or press one of the buttons The Wash 1 light starts to flash The machine is then ready to be reprogrammed e AUTOMATIC SAFETY SYSTEMS e Lid opening safety system As soon as washing commences the lid on your machine is locked When the cycle is finished or when the machine has stopped with the drum full of water the lid unlocks If you have programmed Delayed start the lid is not locked until the waiting period is over and the cycle starts If you wish to open the lid during the cycle press button 5 and wait 1 2 minutes for the safety system to unlock the lid Important Depending on when you wish to open the lid during the cycle this time delay may be a little longer because a cooling down period may also have to be included In fact to avoid your being severely burnt the lid safety system will not open during the cycle unless the temperature inside the machine is below a certain threshold briefly e Water safety system During operation constant control of the water prevents any overflows e Spin safety system Your washing machine is fitted with a safety system that restricts the spin when poor load distribution is detected In this case your washing may be insufficiently spun Redistribute your washing i
7. observe these recommendations since this could result in damage to equipment or physical injury The machine must only be used in accordance with its normal method of operation in order to avoid damaging your washing and your machine Only use washing and maintenance products certified for use in domestic washing machines If you pre treat your washing with stain removers solvents or in general any inflammable or potentially highly explosive product do not insert them into the machine immediately Furthermore you are also recommended not to use solvents or products in aerosol cans near to your washing machine or any electrical appliance in general in a poorly ventilated room risk of fire and explosion If any incidents occur and you cannot resolve them using the remedies we recommend see the section INCIDENTS THAT MAY ARISE call in a qualified professional If you have to open your machine during a cycle for example to add or remove washing depending on the stage the programme is at during washing essentially be careful of the temperature inside the machine which may be very high risk of severe burns When making a new installation the machine must be connected to the water supply with a new hose the old hose must not be re used Do not let children play with the machine and keep your pets away from it e DESCRIPTION OF YOUR MACHINE Do
8. FAGOR WASHING MACHINE INSTALLATION OPERATING AND MAINTENANCE INSTRUCTIONS INSTALLATIONS GEBRAUCHS UND PFLEGEANLEITUNG FUR EINE WASCHMASCHINE N VOD K INSTALACI POU IT A UDRZBE PRA KY INSTRUKCJA INSTALACJI OBS UGI I KONSERWACJI PRALKI MOSOGEP BESZERELESI HASZNALATI ES KARBANTARTASI UTMUTATOJA Downloaded From WashingMachine Manual com Manuals FAGOR 1 3 As part of our commitment to constantly improving our products we reserve the right to make changes to them based age on technical advances to their technical and functional features and appearance Warning Before installing and using your appliance please carefully read this Guide to Installation and Use which will allow you to quickly familiarise yourself with its operation Seite 11 Da wir unsere Produkte st ndig verbessern m chten behalten wir uns das Recht vor ihre technischen funktionellen und ene sthetischen Merkmale zu ver ndern damit sie mit der technischen Weiterentwicklung Schritt halten Wichtig Bitte lesen Sie vor der Inbetriebnahme des Ger tes diese Einbau und Gebrauchsanleitung aufmerksam durch damit Sie sich sehr rasch mit seinem Betrieb vertraut machen k nnen Ics St 5 19 Ve snaze neust le zlep ovat na e v robky prizpUsobovat v voji si vyhrazujeme pr vo zm nit jejich technick funk n
9. ILTER Important Your machine s performance can be affected if you do not clean the pump filter regularly e SOME EXAMPLES OF PROGRAMMES To select the most suitable programme for your type of washing follow the instructions on the labels that most textiles bear Type of textile COTTON WHITES Temperature Max load C 90 5 0 0 Cycle length h hour kg min minute creasing Extra rinse Full drum stop 2h03 2h20 COLOUREDS SYNTHETICS 60 25 1h19 1h40 DELICATES 30 1 0 30 min 40 min WOOLLENS 30 15 28 min 33 min Special programmes HAND WASH RAPID 30 RINSE only 25 l HH SPIN only These functions can be used alone or in combinations no illogical combinations can be made Important The cycle times are provided for an average value without options They may vary according to the wash load the temperature etc If you programme a Prewash you must add 18 to 25 minutes If you programme Extra rinse you must add 17 minutes e DETAILS OF THE PROGRAMMES The main programmes provided by the machine are as follows e Cotton Whites If your washing comprises hard wearing white or coloured COTTONS Important When washing coloureds do not exceed a maximum temperature of 60 C NB During the first few minutes of the programme your machine automati
10. Re insert the plastic component ensuring that it is positioned correctly in the openings at the bottom of the drum and pushing it to the left until it is fully engaged Diagram D19 CLEANING THE PUMP FILTER Option 2 if your machine dopes not have the component shown in Diagram D16 you must proceed as follows to clean your pump filter Turn the drum to position the closed doors facing downwards this will reveal a plastic component Diagram D20 If your machine is fitted with one remove the screw On certain types of machines the component has a clip In this case release the component by pressing on this clip while sliding the component gently to the right Then in all cases turn the drum again open the doors and remove the component by sliding it in the direction of the arrow Diagram D21 Turn the drum slightly towards the front of the machine with the doors open Diagram D22 You can access the pump filter through the openings freed by removing the plastic component Remove the filter from its housing Diagram D22 Remove the various objects it may have in it Rinse it under the tap Diagram D23 Re insert it pushing it firmly into its housing after checking that the housing is clean Re insert the plastic component and the screw by performing all the above operations in reverse order ownloaded From WashingMachine Manual com Manuals
11. anently lit Cancelling while programming washing or during a pause Set the selector 1 to the O position Selector 1 set to This can be done at any time during the cycle or during programming or even during a pause NB 9 y ais q SAP All the lights unlit In all cases after cancelling you must reprogramme everything from the start Ifyou have cancelled during the washing phase remember to empty the water if necessary e End of the cycle NB After spinning some models automatically position the drum opening at the top to provide easy access to the washing This operation lasts at most 3 minutes Then the STOP light comes on permanently indicating that the cycle is over The STOP light is permanently lit Set the selector 1 the O position You can now open the lid and remove your washing For more details on the various functions please refer to the sections DETAILS OF THE PROGRAMMES and DETAILS OF THE OPTIONS Information After a power failure when the power is restored the washing cycle automatically resumes at the point where it was interrupted Downloaded From WashingMachine Manual com Manuals 6 4 PROGRAMMING YOUR MACHINE Maintaining your machine s performance Maintaining the pump filter You must clean the drain pump filter regularly for how to do this see the section CLEANING THE PUMP F
12. best possible conditions in compliance with European Directive 2002 96 EC on Waste Electrical and Electronic Equipment Contact your town hall or your retailer for the used appliance collection points closest to your home We thank you doing your part to protect the environment Control panel Handle for opening the lid remains locked during the cycle O Lever for raising the machine on castors depending on the model Drain hose Cross clamp Q Water supply hose not connected Power supply cable D PAS e REMOVING THE TRANSPORT CLAMPS Important Before using the machine in any way you must first perform the following operations These comprise removing all the components designed to immobilise the drum in your machine during transport These so called releasing operations are necessary for your machine to operate correctly and to conform to the prevailing safety standards If they are not carried out completely this could cause severe damage to your machine while it is operating Remove the washing machine from its plinth check that the wedge supporting the motor is not still inserted in the machine Diagram D3 Remove the 4 screws with a screwdriver Diagram D4 Remove the cross clamp by removing the 2 screws Diagram D5 using a 10 or 13mm spanner depending the model Ensure that you remove the two plastic braces fixed on the cross clamp at the same time as th
13. cally evaluates the washing load you have introduced and adapts the water consumption and the length of the programme accordingly to provide a perfect wash Coloureds Synthetics If your washing comprises of DELICATE COLOURS HARD WEARING SYNTHETICS or MIXED FIBRES e Delicates x gt If your washing comprises NETTING DELICATE FABRICS or FRAGILE TEXTILES NB A programme with agitation and spin phases specially adapted to these types of fabrics e Woollens If your washing comprises WOOLLENS or MACHINE WASHABLE WOOLLENS NB programme with agitation and spin phases specially adapted these types of fabrics e Hand wash vy If your washing comprises SILK or PARTICULARLY DELICATE FABRICS A programme with a very gentle mechanical action and no intermediate spins between rinses The cycle ends with a very gentle progressive spin restricted to 600 rpm Downloaded From WashingMachine Manual com Manuals e Rapid 30 D gt sa This programme enables you to refresh a small load of 2 5 kg of lightly soiled washing composed of WHITES COTTONS COLOUREDS or HARD WEARING SYNTHETICS The cycle time is restricted to around 30 minutes In this programme the washing temperature is automatically programmed at 40 C Important For this programme the doses of detergent should be reduced by half e Rinse only YJ A separate rinse followed by a choice of Either spin and drain Or drain only Drip dry optio
14. d by the washing cycle is higher than your new selection heating the water stops immediately and the cycle continues You can alter the spin speed throughout the cycle You can select Drip Dry 100 and Full drum stop J throughout the washing phase You can activate the Extra rinse 7 option until rinsing starts until the Rinse Spin cycle progress light 7 illuminates You can deactivate all the options throughout the cycle provided that their action has not already finished Downloaded From WashingMachine Manual com Manuals e During delayed start Only for machines fitted with this function Any kind of programme modification is accepted during a delayed start s waiting period You can alter the length of a delayed start period before the cycle effectively starts NB During this period selecting a new time cancels out the previous selection The new period selected is accepted based on the last selection made If you want to cancel the delayed start completely during this period set the selector 3 to the 0 position and then briefly press the Start Pause gt 5 You only activate the Prewash 1 Anti creasing ZA options during a delayed start s waiting period throughout the waiting e When the cycle is over When the STOP light
15. e clamp itself Replace the screws in their initial positions Warning You must block off the two holes using the hole covers provided supplied in the accessories bag Diagram D6 Remove the drum tank assembly locking wedge Diagram D7 To do this Lift the lid on the machine Remove wedge Remove wedge by turning it a quarter turn Release the drum doors locked in the lower position by pressing down on both eaves simultaneously Warning Remove the pipe support collars You must block off the holes revealed with the hole covers supplied in the accessories bag Diagram D8 Advice We would recommend that you keep all the locking components since these must be refitted if you must subsequently transport your machine again Information Your machine has been scrupulously checked before it left the factory You may therefore notice a little water still remaining in the tank or the products box ownloaded From WashingMachine Manual com Manuals e MOVING YOUR MACHINE e Mounting it on castors If your machine is equipped with removable castors you will be able to move it quite easily To mount it on castors swivel the lever on the bottom of the machine from the right to the far left Diagram D9 Important The machine must not rest on the front castors while it is operating remember to return the lever to its initial posit
16. ectly from the machine Check that all the transport wedges have been removed see REMOVING THE TRANSPORT CLAMPS The floor is not level Your machine is resting on its two front castors depending on the model Reset your machine on its feet by pushing the castor engagement lever to the right The washing is not spun or not spun enough You have selected a programme with no spin for example Drip dry The spin safety system has detected poor distribution of the washing in the drum Untangle the washing and programme a new spin e The machine does not drain You have programmed Full drum stop The pump filter is blocked Clean it see CLEANING THE PUMP FILTER for the relevant procedure The drain hose is kinked or squashed e The lid does not open The programme has not yet finished The lid remains locked throughout the programme The drum doors open very slowly On machines fitted with gently opening doors Your machine has not operated for a long time It is located in too cold a position Detergent residue powder is blocking the hinges In all cases everything returns to normal after the doors have opened initially Important As a general rule whatever the anomaly detected you should stop the machine unplug the power cable and shut off the water tap e AFTER SALES SERVICE Possible maintenance on your washing machine should be undertaken by
17. he machine Check that the Programme selector is correctly positioned on O Depending on the model lift the opening handle or press the push button on the front of the machine The lid will open Open the drum by pressing the button on the front door e Insert your washing For optimum washing performance place your washing preferably sorted and folded in the drum distributing it evenly without heaping it up Mix large and small items to obtain an optimum well balanced spin Close the drum Ensure that the drum is correctly closed Important Check that the three hooks and the border of the button are fully visible LOADING THE WASHING PRODUCTS Important Diagram D14 The WASH container may contain powder or liquid but liquid detergent should not be used for programmes WITH Prewash and or WITH Delayed Start depending on the model Concentrated softener should be diluted with warm water Concentrated bleach must be diluted To fill the product containers correctly place the lid fully open Do not exceed the MAX level e Dispensing the detergent The amount of detergent to be used depends on the hardness of the water the extent to which your washing is soiled and the amount of washing to be washed Please refer to the dosing instructions on your pack of detergent Warning in most cases the detergent manufacturer s recommendations apply to the drum filled to the maxim
18. ion e CONNECTING TO THE COLD WATER SUPPLY Connect the supply hose Diagram 010 At one end to the connection on the back of the machine On the other end to a tap fitted with a threaded end 20mm dia x 27 3 4 BSP If you use a Self piercing tap the useful aperture must have a minimum diameter of 6mm Water supply Minimum water pressure 0 1 MPa or 1 bar Maximum water pressure 1 MPa or 10 bars e Replacing a water supply hose When replacing the hose ensure that the hose is tightly fastened and that there is a seal at both ends e DRAINING AWAY THE WASTE WATER Fit the hose bracket provided inside your machine to the end of the drain hose and then connect the hose Diagram D11 Either temporarily over a sink or a bathtub Or permanently to a ventilated U bend If your installation does not have a ventilated U bend check that the connection is not sealed In fact to avoid any waste water flowing back into the machine you are strongly recommended to leave an air gap between the machine s drain hose and the drainpipe In any case the drain hose bracket must be placed at a height of 65 to 90cm higher than the base of the machine Important Ensure that the drain hose is tied firmly in place with cord to avoid the bracket coming loose during draining and causing a flood The waste water can be drained away to the ground provided that the drain hose passes through a point 65 to 90cm higher than the
19. n stop with the drum full of water e Spin only This allows a separate spin and drain Important In the case of Rinse only followed by a spin or Spin only ensure that you select a suitable spin speed for the type of washing in the machine 4 PROGRAMMING YOUR MACHINE DETAILS OF THE OPTIONS Prewash UJ Specially designed for heavily soiled washing mud blood etc A specific initial agitation in cold water precedes a phase of heating to 30 C This agitation phase in cold water enables the particles soiling the washing to be removed before the water is heated Important Detergent must be placed in the container in the products box Anti creasing A This avoids the washing creasing and makes it easier to iron e Extra rinse 1 Especially for sensitive and allergic skin adds an extra rinse to the washing cycle e Delayed start depending on the model You can delay the start of your programme by 1 3 6 9 12 15 or 19 hours so that you can benefit from cheap rate electricity or to have the cycle finish at a desired time To do this use the selector 3 to choose the time you want the cycle to start and press Start Pause 5 NB Even if you forget to press the Start Pause gt button after selecting this option your choice will still be accepted after a few seconds The three cycle progress lights Wash UY Rinse Spin and STOP flash in succe
20. n the connection must not be airtight see the section DRAINING AWAY THE WASTE WATER Drum blocked Check that a small item of laundry e g a handkerchief or a sock etc has not slipped down between the tub and the drum and is stopping the drum from turning To access the bottom of the tub please refer to the section CLEANING THE PUMP FILTER TINS Lid not closed properly Check that the lid is closed and then press the Start Pause button again to restart the cycle e Incidents indicated that require a breakdown engineer You machine also detects some operating faults that systematically require the services of a breakdown engineer In this case these are the three cycle progress lights that flash simultaneously NB Before calling for your breakdown engineer we would recommend that you do the following Set the Programme selector to the O position and remove the electrical plug for at least 10 seconds Reconnect the plug and restart a washing cycle If the fault displayed persists call your breakdown engineer and remember to tell him which indicator lights were lit Important Do not restart a washing cycle if the drum remains locked or if you notice water around your machine of if you notice a burning smell Downloaded From WashingMachine Manual com Manuals Translation agency ALIZE Traduction G1722 01 10 05
21. n speed is automatically restricted in the Delicates Woollens and Hand wash programmes Or drip dry Position 100 The cycle will finish with a gentle spin at 100 rpm Or stop with tub full of water Position UJ Your machine will stop with the tub full of water before the final spin Use the buttons 4 to select any options you wish Light s for the option s selected Select immediate start by pressing Start Pause lt gt Wash UIJ light permanently lit The lights illuminate in succession to show which phase the cycle is at Or use the selector 3 depending on the model to select starting delayed by 1 19 The lights A flash in succession until the cycle hours and then press Start Pause lt gt 5 effectively starts e Adding or removing an item during the cycle impossible during spin Press the Start Pause Q button 5 to interrupt the cycle Add or remove the items of laundry Press the Start Pause Q button 5 to restart the cycle The lid may take 1 2 minutes to unlock NB If you have selected a delayed start you can access the drum instantly at any time in the period before the washing cycle starts without having to interrupt and restart the cycle Light flashing Light A perm
22. n the drum and programme a new spin e Anti foam system You machine can detect when too much foam is being produced during spinning At such times spinning stops and the machine drains The cycle then restarts adapting the spin rates and possibly adding an extra rinse 5 MAINTAINING YOUR MACHINE e CLEANING THE PUMP FILTER Option 1 The way to access your pump filter may differ according to the model of the machine see options 1 and 2 This filter collects the small objects you may have inadvertently left in your clothes and prevents them from disrupting the pump s operation To clean the filter proceed as follows Open the drum doors At the back of the drum you will see a plastic component Diagram D15 Release this Diagram D16 To do this Insert a rod a pencil or a screwdriver for example into the hole in the component Press down vertically with the rod while pushing the component over to the right until it is released from its housing Remove the component Turn the drum slightly towards the front of the machine with the doors open Diagram D17 You can access the pump filter through the openings freed by removing the plastic component Remove the filter from its housing Diagram D17 Remove the various objects it may have in it Rinse it under the tap Diagram D18 Re insert it pushing it firmly into its housing after checking that the housing is clean
23. ssion from left to right during the whole of the waiting period before the cycle effectively starts Full drum stop J This function enables you to remove the washing from your machine before the spin phase or to delay this phase with you washing remaining in water to prevent creasing NB When the machine is stopped with the tub full of water the Rinse Spin cycle progress light flashes Then If you want to drain after spinning use the selector 2 suitable spin speed for your type of washing The programme will end automatically If you just want to drain turn the selector 2 100 to choose a to Drip Dry position MODIFYING A WASHING PROGRAMME e During programming Anything can be changed before the Start Pause lt gt button 5 pressed e After the cycle has started You can change the type of textile for example switch from COTTON to SYNTHETICS etc In this case check that the options you previously selected are still there You must confirm your new selection by pressing the Start Pause button 5 The machine may then possibly drain off some of its water e Throughout the cycle Depending on your model the following changes are possible without pressing the Start Pause lt gt button You can change the temperature for the same type of textile NB If the temperature achieve
24. switches and do not remain depressed A 5 any case the Start Pause button cannot cancel a programme Nature of the washing and Cycle progress Start Pause the temperature l Important Before starting your machine check that the power cable is plugged in and the water tap is open Also ensure that the drum doors are closed correctly and the machine s lid is shut During the End of Cycle phase any action one of the controls the selectors or the buttons returns you to Programming mode As a safety measure when the cycle is over we 2 recommend that you unplug the power Spin speed setting J 1 cable and turn off the water tap Delayed start setting Options depending on the model e Programming a washing cycle Indicator lights and position of the selectors Turn the selector 1 choose the most suitable programme and washing temperature for Wash UI light flashing the type of fabric to be washed If you have selected rinse only or spin only NB Turning the selector to any position other than provides power to the machine itis the Rinse Spin light 07 that flashes Using the selector 2 choose Selector 2 on Either a suitable spin speed for your type of washing Position 600 for example The spi
25. um Adjust the dosage correctly to the weight of the washing you have placed in the machine These recommendations will help you to avoid using too much detergent which causes foam to be produced Too much foam can reduce your machine s performance and increase the length of the washing cycle and the consumption of water e Detergents for woollens and delicate fabrics You are recommended to use an appropriate detergent for washing these fabrics avoid placing such detergents directly on the drum because they have an aggressive action on the metal e Before your first wash Before making your first wash we recommend that you carry out a COTTON 90 wash without pre wash and with no washing the drum using a 1 2 measure of your usual detergent in order to eliminate any residues from manufacturing that may remain in your machine STANDARD COMPARISON TESTING PROGRAMME Cotton Q 60 C 5 kg no options max spin To comply with the statement on the label the tests are conducted in accordance with European Directive 92 75 EEC at nominal capacity ensuring complete use of the CEI detergent from the start of the washing phase Pre wash container powder Wash container powder or liquid amp Softener A Bleach POWDERED DETERGENT a LIQUID DETERGENT ownloaded From WashingMachine Manual com Manuals 4 PROGRAMMING YOUR MACHINE e PROGRAMMING Information All the buttons are on micro
26. wnloaded From WashingMachine Manual com Manuals You must immediately make any obsolete machine unusable Disconnect and cut off the power cable flush with the machine Close the water tap and remove the hose Disable the door lock If there is a risk of frost disconnect the water hose and drain off any water that may remain in the drain hose by placing this as low as possible in a bowl e SAVING ENERGY Only programme a prewash when it is absolutely necessary for example for very dirty sports or working clothes etc A low temperature programme is sufficient for impeccable washing results when your washing is only slightly or moderately dirty For washing that is only slightly dirty select a short washing cycle Express or Flash depending on the model Use the right amount of washing products for the hardness of the water the amount of washing and how dirty it is and follow the instructions on the detergent packs e ENVIRONMENTAL PROTECTION This appliance s packaging material is recyclable Help recycle it and protect the environment by dropping it off in the municipal receptacles provided for this purpose Your appliance also contains a great amount of recyclable material It is marked with this label to indicate the used appliances that should not be mixed with other waste This way the appliance recycling organised by your manufacturer will be done under the
27. your machine in a damp poorly ventilated room Install your machine in an area where it could be subject to water splashes Install your machine on a carpeted floor If you cannot avoid doing this please take every precaution to avoid blocking air circulation at the bottom of the machine in order to ensure that the internal components are well ventilated Levelling the machine Use a spirit level to check that the floor is horizontal maximum slope 2 i e discrepancy of approximately 1cm over the width and of 1 5cm over the depth of the machine e Adjustable feet Some machines are fitted with two adjustable feet at the front to enable you to compensate for any unevenness in the floor Proceed as follows to adjust the feet to level and stabilize your machine Set the machine on its castors or tilt it slightly backwards if it does not have retractable castors Screw in or unscrew the feet to adjust the height to suit the shape of the floor Diagram D13 Set the machine back on its feet and check that it is stable e TEXTILE MAINTENANCE CODES Washing 7 Never exceed the indicated temperatures Use of cold diluted bleach possible A Iron Low A Medium A High GA Dry clean mineral spirit perchlorethylene all solvents NB crossed out code indicates that it is forbidden X 5 e LOADING YOUR WASHING Perform these actions in the following order e Open t
28. zembehelyez si s haszn lati utas t st gy gyorsabban megismeri a g p m k d s t Downloaded From WashingMachine Manual com Manuals 2 1 INTRODUCTION TO YOUR MACHINE e CONTENTS Removing the transport packing Moving your machine 0 0000 ea e a E eee Connecting to the cold water supply Draining away the waste water Connecting to the electricity Installing your machine 0 00 0002 c cee Loading your washing Loading the washing products Page 6 Details of the programmes and options T Modifying a washing programme 8 Automatic safety systems 8 Cleaning the pump filter 9 Maintaining your machine 9 Incidents that arise 10 Messages indicated by the various lights flashing 10 SAFETY ADVICE Important This machine is only for domestic use and is designed to wash rinse and spin machine washable textiles You must observe the following instructions We refuse to accept any liability and the guarantee if you do not
Download Pdf Manuals
Related Search