Home

Eurosec

1. AF CPA USER B VENN UAL g Contents IN POGUCHION si 4222 sive deee eh Qs rennt epis Full Setting the System Part Setting the System using Part1 Part Setting the System using Part 2 or 3 Unsetting the System Display After Alarm Resetting After Alarm Programmable User Options Zone Remove Option System Test Turning Chime On Off Programming User Codes Introduction Welcome to the eurosec control panel Your installation company will have programmed your system to protect your premises to the highest possible standards Several user programmable options are available that will be covered later in this manual Throughout this manual refer ence will be made to the User Code the factory set default is 5678 This code is programmable along with eight other User Codes Full Setting the System Two methods are available for Full Set After checking the premises are secure 1 Press Quick followed by Full OR Enter a valid User Code followed by Full 2 The exit tone will now sound 3 Exit the premises via an authorised exit route Note Pressing the Quick key during exit will shorten the exit time to 3 seconds Note To abort the exit enter a valid User Code Part Setting the System using Part 1
2. 2 Press 5 the display will show 3 Violate each zone on the system as you do so the corresponding LED will extinguish to verify its integrity 4 To test the bells external sounders and strobe press 9 To stop the bell test press 9 again 5 To escape back to Unset press 0 three times Turning Chime On Off Your installation company may have programmed a group of zones or a single zone as Chime This Chime function may be turned on or off by the User 1 Enter a valid User Code followed by No the display will show Tamp Day O a3 Power 2 Press 7 the display may show or Power 3 If LEDs 1 to 7 are On then Chime is On If LEDs 1 to 7 are Off then Chime is Off Press No to change the Chime Status 4 To escape back to Unset press 0 three times Programming User Codes Up to nine user codes may be programmed on predetermined levels these are User Numbers 1 to 3 Master Level Allows Set Part Set Unset and User Programming Mode User Numbers 4 to 7 User Level Allows Set Part Set and Unset User Numbers 8 to 9 Set Only Level Allows Set Only User Number 1 is factory default 5678 This code may only be changed There is no facility for deleting this code All other codes may be changed or deleted as required To program User Codes 1 Enter a valid User Code followed by No the display will show OW ET Day Part Power 2 Press 9 the display will show 4
3. Up to three Part Sets may be available for your system Please refer to the customer details at the rear of this manual for information about Part Set zones Part Set zones will be omitted from the system when that particular Part Set is used To set the system using Part 1 1 Press Quick followed by Part OR Enter a valid User Code followed by Part 2 Retire to an unprotected area Part Setting the System using Part2 or 3 Two other Part Sets may be available for your system Part 2 is a sec ond set of zones that may be omitted and Part 3 will combine Part 1 and Part 2 To use Part 2 or 3 1 Press Quick followed by 2 or 3 OR Enter a valid User Code followed by 2 or 3 2 Retire to an unprotected area Note Pressing the Quick key during exit will shorten the exit time to 3 seconds Note To abort the exit enter a valid User Code Unsetting the System 1 Enter the premises via an authorised Entry Point 2 The Entry Tone will sound 3 Proceed to the keypad and enter a valid User Code Display After an Alarm After an alarm has occurred the system should be unset as above The display will show the zone that caused the alarm via a flashing LED Resetting After an Alarm After an alarm the system needs to be reset To reset the system If Any Code Reset has been programmed 1 Press Reset Or If Master Code Reset has been programmed 1 Enter a valid User Code 2 Press Reset Note The terms of your insurance may p
4. Enter the four digit code you require the display will show provided your code has been accepted Oy Oey Oru Power or If your code has not been accepted Tamp Day Power If your code has not been accepted it may already be in use please return to step 1 and use a different code 5 Provided the code has been accepted in 4 you may escape to Unset by pressing 0 twice Keypad Alert If programmed by your installation company keys 1 amp 3 when pressed together will act as alert keys The exact function will depend on what they have been programmed for but for example if they are pro grammed as panic pressing them will activate the alarm when the sys tem is set or unset Keypad activation is indicated by LEDs 1 4 3 Flashing Tamper Tampers and other system problems will be indicated via the Tamp LED Please contact your installation company System Details Installation Company Name Installation Company Address Fax ee moo Ct 3C OO Cao CC 5C r CZ TF Baa s Installation Date a sid pale Service Timer Serviced eurosec Installed By PR4966 Rev2 0
5. rohibit User reset Contact your installation company if none of the above procedures are effective Programmable User Options Throughout this section reference will be made to the LEDs on the dis play Three modes are possible for each LED ON OFF or FLASHING Programmable User Option may only be accessed via a Master Code Fig 1 LED Modes Key OFF O oN FLASHING Zone Remove Option This option allows individual zones to be removed omitted when the system is being set It is only applicable to the one Set state and will need to be repeated for subsequent Sets If you are removing particu lar zones on a regular basis ask your installation company to include them in a Part Set 1 Enter a valid User Code followed by No the display will show OW Enis Day Oa Power 2 Press 4 the display will show Power 3 Press the key s corresponding to the zone s you wish to remove omit from the next Set 4 Press 0 twice the display will show Tamp O u Power 5 Press Full for Full Set or Press Part for Part 1 Set or Press 2 for Part 2 Set or Press 3 for Part 3 Set 6 The system will now start the relevant Set with the zones you selected removed omitted Note This will be for the one Set state only System Test This option allows the User to test zones bells and strobes on the system 1 Enter a valid User Code followed by No the display will show OBET OJPEN ONT Power

Eurosec

Contents

Download Pdf Manuals

Related Search

Related Contents