User manual Dishwasher ZKS5653
Contents
1. Use only special salt suitable for dishwashers Release the button The end of programme indicator light will flash The number of flashes corresponds to current level set The end of programme indicator light might flash 5 times for example The flashing is repeated every 5 seconds To change the level press the start cancel button Each time the button is pressed the level increases Level 1 follows level 10 The end of programme indicator light indicates the new setting To memorise the operation turn the programme se lector dial to position off e A Unscrew the cap Only before filling with Using the funnel provided salt for the first time fill pour in the salt until the the salt container with wa container is filled with salt ter IMPORTANT Immediately start a complete programme IMPORTANT Water will overflow from the containeras saltis added Sy di Remove any trace of salt Replace the cap tightly turning it clockwise until it stops with a click IMPORTANT Top up the special salt when the light on the control panel illuminates Filling with rinse aid i Open the lid Fill up with rinse aid The Clean up any rinse aid maximum level forfilling is which overflows Close indicated by max the lid and press until it locks SS 10 a ZANKER CAUTION Never fill the rinse aid dispenser with any oth2. basket first and then the aa 2 upper one this will avoid water dripping from When the washing programme has finished it the upper basketonto the dishes in the lower is recommended that the dishwasher is un one plugged and the water tap turned off 14 E ZANKER Care and cleaning Cleaning the filters IMPORTANT NEVER use the dishwasher without filters In correct repositioning and fitting of the filters will produce poor washing results Clean filters A B andC Turn the handle about 1 4 Remove filter A from the thoroughly under running turn anticlockwise and re base of the washing com water move filters B and C partment Putthe flat filter A backin Replace the filters and the base of the washing lock by turning the handle compartment and ensure clockwise to the stop that it fits perfectly under the two guidesD Cleaning the spray arms External cleaning NEVER try to remove the spray arms Clean the external surfaces of the machine and control panel with a damp soft cloth If If residues of soil have clogged the holes in the necessary use only neutral detergents Never Spray arms remove them with a cocktail stick 15 use abrasive products scouring pads or sol vent acetone trichloroethylene etc Internal cleaning Ensure that the seals around the door the de tergent and rinse aid dispensers are cleaned regularly with a damp cloth We recommend ever
3. rinse aid dosing The detergent may be the cause Contact the de tergent manufacturer s consumer care line Dimensions Electrical connection Voltage Overall power Fuse Water supply pressure Minimum Maximum MPa Capacity place settings Max weight kg Width x Height x Depth Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher s door 59 6 x 81 8 87 8 x 57 5 0 05 0 8 12 38 5 19 Noise level dB A 51 Consumption values The consumption values are intended as a iations of the power supply and the amount of guide and depends on the pressure and the dishes temperature of the water and also by the var Consumption values Programme Programme duration in Energy consumption in Water litres minutes A Intensive 70 85 95 1 8 2 0 22 25 B Normal 65 105 115 1 5 1 7 23 25 C Eat Load Run 65 30 0 9 9 D Eco 50 Test pro 140 1 05 16 gramme for Test Insti tutes E Rinse and Hold 12 0 1 5 Hints for test institutes Testing in accordance with EN 60704 mustbe aid dispenser have been filled with salt and carried out with appliance fully loaded and us rinse aid respectively and using the test pro ing the test programme see Consumption gramme see Consumption values values Testin accordance with EN 50242 must be carried out when the salt container and rinse Full load 12 standard place settings Amount of detergent require
4. ZANKER User manual Dishwasher ZKS5653 PB TIN Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances Please read this user manual carefully and Keep it throughout the product life cycle as a reference document The user manual should be passed on to any future owner of the appliance Contents oOo N N nD A Ww Filling with rinse aid 10 Adjusting the dosage of rinse aid ____ 11 Loading cutlery and dishes 11 Something not working Technical data 13 14 15 16 17 19 20 20 21 Safety information In the interest of your safety and to ensure the correct use before installing and first using the appliance read this user manual carefully in cluding its hints and warnings To avoid unnecessary mistakes and accidents it is im portant to ensure that all people using the appliance are thoroughly familiar with its opera tion and safety features Save these instruc tions and make sure that they remain with the appliance if itis moved orsold so thateveryone using itthrough its life will be properly informed on appliance use and safety Correct use This dishwasheris only intended for washing household utensils suitable for machine washing Do not put any solvents in the dishwasher This could cause an explosi
5. adjusted according to grees dH French degrees TH and mmol the hardness of the water in your area Y our millimol per litre international unit for the local Water Authority can advise you on the hardness of water hardness of the water in your area Water hardness Adjusting the water hardness Use of salt setting TH mmol l manually electronically 51 70 91 125 9 1 12 5 2 level 10 yes 43 50 76 90 7 6 8 9 2 level 9 yes 37 42 65 75 6 5 7 5 2 level 8 yes 29 36 51 64 5 1 6 4 2 level 7 yes 23 28 40 50 4 0 5 0 2 level 6 yes 19 22 33 39 3 3 3 9 2 level 5 yes 15 18 26 32 2 6 3 2 1 level 4 yes 11 14 19 25 1 9 2 5 1 level 3 yes 4 10 7 18 0 7 1 8 1 level 2 yes lt 4 lt lt 0 7 1 level 1 no The water softener must be set in both ways manually using the water hardness dial and electronically Setting the water softener manually see table The water softener is factory set at position 2 Set switch to position 1 or 2 ZANKER Setting the water softener electronically see table The water softener is factory set at position 5 The dishwasher must be switched off x O O m A on O A RESET os Press and hold the start cancel button and turn the programme selector dial clockwise till the first pro gramme Keep the button pressed until the programme selector indicator light and the start cancel indicator light start flashing Filling with dishwasher salt Z N CAUTION
6. amme selector indicator light ZANKER when in this position the machine is switched off corresponding light off when the marker on the dial corresponds with a programme the machine is switched on and a pro gramme is selected programme selector indicator light on Starting the washing programme 1 Select a washing programme 2 Press the Start Cancel button corresponding light on IMPORTANT Once the programme has started if you want to change the selection made you must cancel the wash ing programme in progress Cancel the washing programme in progress 1 Press and hold the Start Cancel button until the corresponding light turns off 2 Release the Start Cancel button 3 Turn the programme selector dial to the Off po sition or select a new washing programme check that there is detergent in the detergent dispenser Illuminates when the washing programme is selected Indicator lights Wash indicator light o HM Dry indicator light M End of programme indicator light gt Illuminates when the washing and rinsing phases are running Illuminates when the drying phase is running Illuminates when the washing programme has ended Switch off the dishwasher by returning the programme selector dial to the Off position The On Off indicator light turns off Italso has added functions of visual signalling as the setting of the water softener intervention of an alarm due to the malfunction
7. d 5g 25 g Type B Rinse aid setting position 4 Type Ill 20 aint A NN Anan Cutlery basket Lower basket cup racks position A Installation Z N WARNING Z N WARNING Any electrical and or plumbing work required to install this appliance should be carried out by a qualified electrician and or plumber or compe tent person Water connection ZAN WARNING The dishwasher mustnotbe connected to open water appliances or instantaneous water heat ers This dishwasher may be fed with either hot max 60 or cold water Nevertheless we ad vise you a cold water supply Only use for connection to the water mains new hose set old hose setmustnotbe reused Z N CAUTION If the machine is connected to new pipes or pipes which have notbeen used for a long time you should run the water for a few minutes be fore connecting the inlet hose Water inlet hose with safety valve Connect the inlet hose to a water tap with an external thread of 3 4 After connecting the double walled water inlet hose the safety valve is next to the tap 21 If the water inlet hose leaks the safety valve cuts off the water supply Z WARNING The electrical cable for the safety valve is in the double walled water inlet hose and is live Drain hose Therefore do not immerse the water inlet hose or the safety valve in water Take care when installing t
8. d endangering their lives The symbol on the product or on its pack aging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equip ment By ensuring this product is disposed of correctly you will help prevent potential nega tive consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal Something not working The dishwasher will not start or stops during operation Certain problems are due to the lack of simple maintenance or oversights which can be solved with the help of the indications described in the chart without calling out an engineer ZANKER service or the shop where you purchased the product Switch off the dishwasher open the door and carry outthe following suggested corrective ac tions Fault code and malfunction Possible cause and solution continuous flashing of the start cancel indicator light e 1 flash of the end of programme indicator light The dishwasher does not fill with water continuous flashing of the start cancel indicator light 2 flashes of the end of programme indicator light The dishwasher will not drain continuous flashing of the start cancel
9. dishwasher salt Fill the rinse aid dispenser When using tablets that integrate rinse aid and detergent there is no need to fill up with rinse aid set the water softener add special dishwasher salt When using tablets that integrate rinse aid detergent salt function and other additives there is no need to fill up with special salt or rinse aid Set the water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply which would have a det ZANKER Check whether these detergents are suitable for your water hardness Follow the manufac turers instructions Setthe water hardness to level 1 IMPORTANT If the drying results are not satisfactory we rec ommend that you 1 Fillup the rinse aid dispenser with rinse aid 2 Setthe rinse aid dosage to position 2 If you decide in future to use separated deter gents we advise that you Fill up the salt and rinse aid container Adjust the water hardness setting to the highest level and perform 1 normal washing programme without loading any dishes Adjustthe water hardness setting according to the hardness of the water in your area Adjust the rinse aid dosage rimental or adverse effect on the operation of the appliance The higher the content of these minerals and Salts the harder your water is Water hardness is measured in equivalent scales German de The softener should be
10. engineer in the event that a repair is required Levelling Good levelling is essential for correct closure and sealing of the door When the appliance is correctly levelled the door will not catch on either side of the cabinet If the door does not close correctly loosen or tighten the adjustable feet until the machine is perfectly level See enclosed template 23 nH ZANKER www electrolux com 156994870 00 20072007 Subject to change without notice CE
11. er substances e g dishwasher cleaning agent liquid detergent This would damage the appliance Top up the rinse aid indica tor B becomes clear Adjusting the dosage of rinse aid Increase the dose if there are drops of water or Reduce the dose if there are whitish streaks on lime spots on the dishes after washing the dishes ora bluish film on glassware or knife blades Open the lid Set the dosage level The Close the lid and press un dose is factory setin po til it locks sition 4 Loading cutlery and dishes Sponges household cloths and any objectthat When loading the dishes and cutlery please can absorb water may not be washed in the niote dishwasher Dishes and cutlery must not impede the rotation of the spray arms Load hollow items such as cups glasses pans etc with the opening downwards so Before loading the dishes you should Remove all left over food and debris Soften remnants of burnt food in pans 11 that water cannot collect in the container e Plastic items and pans with non stick coat or a deep base ings have a tendency to retain water drops Dishes and items of cutlery must not lie these items will not dry as well as porcelain inside one another or cover each other and steel items To avoid damage to glasses they must Light items plastic bowls etc must be loa not touch ded in the upper basket and arranged so Lay small objec
12. he water inlet hose Place the water inlet hose in such a way that itis always lower than the bottom edge of the Safety valve If the water inlet hose or the safety valve is damaged remove the mains plug immediately Z N CAUTION A water inlet hose with safety valve MUST only be replaced by your local Service Force Centre Connect drain hose to the Requiredheight 30to100 Ensure thatthe hoses are When connecting the cm above bottom of the dishwasher sink Secure it with the supplied hose clamp lf you use a drain hose extension the total length should not be longer than 4 metres Likewise the internal diameter of the couplings used for connections to the waste outlet must 22 not kinked crushed oren drain hose to an under tangled sink trap spigot the entire plastic membrane A must be removed F ail ure to remove allthe mem brane will result in food particles building up over time eventually blocking the dishwasherdrain hose Spigot be no smaller than the diameter of the hose provided Electrical connection Z N CAUTION Safety standards require the appliance to be earthed Prior to using the appliance for the first time ensure thatthe rated voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed The fuse rating is also to be found on the rating plate Always plug the mains plug into a correc
13. indicator light 3 flashes of the end of programme indicator light e The water tap is blocked or furred with limescale Clean the water tap The water tap is turned off Tum the water tap on e The filter where present in the threaded hose fitting at the water inlet valve is blocked Clean the filter in the threaded hose The water inlet hose has not been correctly laid or itis bent or squashed Check the water drain hose connection e The sink spigotis blocked Clean out the sink spigot The water drain hose has not been correctly laid or itis bent or squashed Check the water drain hose connection Anti flood device is activated Close the water tap and contact your local Service Force Center 17 Fault code and malfunction Possible cause and solution The programme does not start Once these checks have been carried out close the dishwasher s door and switch on the appliance Press the button of the programme that was running before the intervention of the alarm The programme will continue from the point at which it was interrupted If the malfunction or fault code reappears con tact the Service Force Centre For other fault codes notdescribed in the above chart please contact your Service Force Cen tre Contact your local Service Force Centre quot ing the model Mod product number PNC and serial number S N 18 The dishwasher s door has not been properly closed Close the door The
14. main plug is not plugged in Insert the main plug The fuse has blown out in the household fuse box Replace the fuse Delay start has been set If dishes are to be washed immediately cancel the delay start This information can be found on the rating plate located on the side of the dishwasher door So that you always have these numbers at hand we recommend you to make a note of them here ZANKER The wash results are not satisfactory The dishes are not clean The dishes are wet and dull There are streaks milky spots or a bluish coating on glasses and dishes Water drops have dries onto glasses and dishes If after all these checks the problem persists contact your local Service Force Centre Technical data The wrong washing programme has been selected The dishes are arranged in such a way as to stop water reaching all parts of the surface The baskets must not be overloaded The spray arms do notrotate freely due to incorrect arrangement of the load The filters in the base of the washing compartment are dirty or incorrectly positioned Too little or no detergent has been used Where there are limescales deposits on the dishes the salt container is empty or the incorrect level of the water softener has been set The drain hose connection is not correct The salt container cap is not properly closed Rinse aid was not used The rinse aid dispenser is empty Decrease rinse aid dosing Increase
15. of the machine Indicator lights Salt refilling indicator light S llluminates when special salt needs to be filled It can remain illuminated several hours after the salt has been filled Washing programmes Degree of soil Type of load Programme description foe 70 g B Normal 65 2 c Eat load run Rinse and Hold DF Heavy soil Crockery cutlery pots and pans Normal soil Crockery cutlery pots and pans Light soil Crockery and cutlery Normal soil Crockery and cutlery Any Partial load to be completed later in the day Prewash Main wash 2 intermediate rinses Final rinse Drying Prewash Main wash 2 intermediate rinses Final rinse Drying Main wash Final rinse Prewash Main wash 1 intermediate rinse Final rinse Drying 1 cold rinse to avoid food scraps from sticking together This programme does not require the use of deter gent 1 Ideal for washing a partially loaded dishwasher This is perfect daily programme made to meet the needs of a family of 4 persons who only wish to load breakfast and dinner crockery and cutlery 2 Test programme for test institutes ea First use Before using your dishwasher for the first time Ensure thatthe electrical and water connec tions comply with the installation instructions Remove all packaging from inside the appli ance Set the water softener Pour 1 litre of water inside the salt container and then fill with
16. on Knives and other items with sharp points must be loaded in the cutlery basket with their points down or placed in a horizontal position in the upper basket Only use products detergent salt and rinse aid suitable for dishwashers Avoid opening the door whilst the appliance is in operation hot steam may escape Do not take any dishes outof the dishwasher before the end of the dishwashing cycle After use isolate the appliance from the power supply and turn off the water supply This product should be serviced only by an authorised service engineer and only genu ine Spare parts should be used Under no circumstances should you attempt to repair the machine yourself Repairs car ZANKER ried out by inexperienced persons will cause injury or serious malfunctioning Contact your local Service Force Centre Always in sist on genuine spare parts General safety Dishwasher detergents can cause chemical burns to eyes mouth and throat Could en danger life Comply with the safety instruc tions of the dishwasher detergent manufacturer The water in your dishwasheris not for drink ing Detergent residues may still be present in your machine Ensure that the door of the dishwasher is always closed when itis not being loaded or unloaded In this way you will avoid anybody tripping over the open door and hurting themselves Do notsit or stand on the open door Child safety This appliance is designed to be operated b
17. the upper basket load items plastic bowls etc racks canbe folded up them starting from the rear positions tilting them must be loaded in the up wards Slightly forwards and avoiding the front positions near per basket and arranged the door so they do not move Adjusting the height of the upper basket If washing very large plates you can load them in the lower basket after moving the upper bas ket to the higher position Maximum height of the dishes in upper basket lower basket With upper basket raised 20 cm 31 cm With upper basket lowered 24cm 27 cm IMPORTANT When the basket is in the higher position you will not be able to use the cup racks Move the front runner Refit the basket in the stops A ofthe upper bas higher position and re ket outwards and slide the place the stops A in their basket out original position 13 Use of detergent IMPORTANT Observe the manufacturer s dosing and stor Only use detergents suitable for dishwashers age recommendations wash add an additional tablets place detergent detergent dose in com tablets in compartment A partmentB Unloading the dishwasher Hotdishes are sensitive to knocks e Water may appear on the sides and the door The dishes should therefore be allowed to of the dishwasher as the stainless steel will cool down before removing from the appli eventually become cooler than the dishes nh Z N CAUTION e Empty the lower
18. tly in stalled shockproof socket Multi way plugs connectors and extension cables must not be used This could constitute a fire hazard through over heating If necessary have the domestic wiring system socket replaced In case that the electrical ca ble has to be replaced contact your local S erv ice Force centre The plug mustbe accessible after the appliance has been installed Never unplug the appliance by pulling on the cable Always pull the plug The manufacturer accepts no liability for failure to observe the above safety precautions Fitting under a counter IMPORTANT Carefully follow the instructions on the enclosed template for building in the dishwasher and fit ting the furniture panel ZANKER ZAN WARNING The dishwasher mustbe secured againsttilting Therefore make sure that the counter it is fixed under is suitably secured to a fixed structure adjacent kitchen units cabinets wall This dishwasher is designed to be fitted under a kitchen counter or work surface No further openings for the venting of the dishwasher are required but only to let the wa ter fill and drain hose and power supply cable pass through The dishwasher incorporates adjustable feet to allow the adjustment of the height During all operations that involve accessibility to internal components the dishwasher has to be unplugged Be sure that once the appliance has been in Stalled itis easily accessible for the service
19. ts in the cutlery basket they do not move For washing in the dishwasher the following cutlery and dishes are not suitable are of limited suitability e Cutlery with wooden horn china or mother of e Only wash stoneware in the dishwasher if it is pearls handles Specially marked as being dishwasher safe by the e Plastic items that are not heat resistant manufacturer Older cutlery with glued parts thatare nottempera Glazed patterns may fade if machine washed ture resistant frequently Silver and aluminium parts have a tendency to dis Pewter or copper items colour during washing Residues e g egg white o E EE S egg yolk and mustard often cause discolouring and i staining on silver Therefore always clean left overs Steel items prone to rusting from silver immediately if itis not to be washed e Wooden platters straight after use Items made from synthetics fibres Bonded cutlery items or dishes Load cutlery For bestre Place knives and other Load the lower basket Ar sults we recommend you items of cutlery with sharp range serving dishes and to use the cutlery grid pro points or edges with their large lids around the edge vided ifthe size and di handles facing upwards of the basket mensions of the cutlery Risk of injury allow it 12 ZANKER Load upper basket Light For taller items the cup If plates are to be loaded in
20. y 3 months to run the wash programme for heavy soiled dishes using de tergent but without dishes Prolonged periods of non operation If you are not using the machine for any pro longed period of time you are advised to 1 Unplug the appliance and then turn off the water 2 Leave the door ajar to prevent the forma tion of any unpleasant smells 3 Leave the inside of the machine clean Environmental concerns Packaging material The packaging materials are environmentally friendly and can be recycled The plastic com ponents are identified by markings e g gt PE lt gt PS lt etc Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities Z N CAUTION When a unit is no longer being used Pull the plug out of the socket Cutoff the cable and plug and dispose of them 16 Frost precautions Avoid placing the machine in a location where the temperature is below 0 C If this is unavoidable empty the machine close the ap pliance door disconnect the water inlet pipe and empty it Moving the machine Ifyou have to move the machine moving house etc 1 Unplug it 2 Turn the water tap off 3 Remove the water inlet and discharge ho Ses 4 Pull the machine out together with the ho Ses Avoid over tilting the machine during transpor tation Dispose of the door catch This prevents children from trapping themselves inside an
21. y adults Don t allow children to use the dishwasher unsupervised Keep all packaging well away from children There is risk of suffocation Keep all detergents in a safe place out of children s reach Keep children well away from the dishwasher when the door is open Installation Check your dishwasher for any transport damage Never connecta damaged ma chine If your dishwasher is damaged con tact your supplier All packaging must be removed before use Any electrical and plumbing work required to install this appliance must be carried out by a qualified and competent person For safety reasons it is dangerous to alter the specifications or attempt to modify this product in any way Never use the dishwasher if the electrical supply cable and water hoses are damaged Control panel AlO cies E th BIQ 6s D S so Programme selector dial and On Off switch Start cancel button Indicator lights Programme selector indicator light or if the control panel work top or plinth area are damaged such thatthe inside of the ap pliance is freely accessible Contact your local Service Force centre in order to avoid hazard All sides of the dishwasher must never be drilled to prevent damage to hydraulic and electric components Z N WARNING For electrical and water connection carefully follow the instructions given in specific para graphs Programme selector dial and On Off switch Start cancel button Progr
Download Pdf Manuals
Related Search