6. install the hood 5. install the adapter/damper (cont`d) 7. connect
Contents
1. A HD0217 7 CONNECT WIRING A WARNING Risk of electrical shock Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards Before connecting wires switch power off at service panel and lock service disconnecting means to prevent power to be switched on accidentally Connect cable to range hood wiring using included wire connectors Connect BLACK to BLACK WHITE to WHITE and GREEN or BARE WIRE to GREEN ground screw 1 A WARNING Do not forget to connect the ground ai Broan at 1 rangehoods COM is a division of kitchen accessories U N E t M if 8 Call 1 800 667 8721 anywhere in the US and Canada www rangehoods com 8 REINSTALL BOTTOM PANEL AND FILTERS Reinstall the bottom panel using the retaining screw previously removed in step 4 plus 4 others from parts bag Refer to illustration beside Then reinstall filters HO0092 9 FLUORESCENT LAMPS Z WARNING This hood has fluorescent lamps containing mercury Dispose of appropriately according to local laws and requirements This range hood must use compact fluorescent lamps 120 V 13 W PLC13 2700 K with G24q 1 base included NOTE The range hood is shipped with both fluorescent lamps packed behind the light diffuser 1 To access fluorescent lamps remove the light diffuser by pushing on its both tabs and pulling it down 2 To install the fluorescent lamps2. 12 SERVICE PARTS MODEL QDE Call 1 800 667 8721 anywhere in the US and Canada www rangehoods com ZA HL0095 PART No No V13296 DESCRIPTION ADAPTER DAMPER a 4 V15434 V15433 ROCKER SWITCH WHITE PAIR OVERLAY WHITE ROCKER SWITCH BLACK PAIR OVERLAY BLACK V03623 V01752 FLUORESCENT LAMP LIGHT DIFFUSER V01765 V01988 MOTOR BLOWER WHEEL V16119 V16117 BOTTOM PAN WHITE BOTTOM PAN BLACK V01757 V14131 INLET RING MICROMESH FILTER THE PAIR V02104 V06756 SECONDARY CAPACITOR 7 5UF CAPACITOR 11 5uF Hla oO N loos w mM V03649 BALLAST HARNESS SOCKET LAMPS INCLUDED V06727 INSTALLATION amp USER MANUAL V04281 Item not shown HARDWARE BAG 1 WIRE CLAMP 2 WIRE CONNECTORS 6 No 6 x 1 2 SCREWS 5 NO 8 x 1 2 DOUBLE THREAD SCREWS a a oo oo ss os pe ila 12 Broan at rangehoods COM is a division of kitchen accessories U N E t M iF e E
3. of kitchen accessories u N E t M i T E 8 Call 1 800 667 8721 anywhere in the US and Canada www rangehoods com 11 OPERATION Always turn on the hood before begining cooking in order to establish an air flow in the kitchen Let the blower run for a few minutes to clear the air after turning off the range ROCKER SWITCH CONTROL A ON OFF BLower AND SPEED CONTROL SWITCH This 3 position rocker switch controls the blower speed Pressing on left side 1 will result in low speed operation while pressing on right side 2 will turn on the blower to high speed To stop the blower operation set the rocker switch to the central position 0 B ON OFF LIGHTING CONTROL SWITCH This 3 position rocker switch controls the lighting Press either on left side 1 or right side 1 to obtain full lighting To shut off the lights set the rocker switch to the central position 0 MECHANICAL PUSH BUTTON CONTROL A OFF Blower SWITCH Press on this switch to stop the blower operation B SPEED BLOWER SWITCHES Press on left switch 1 to turn on the blower on low speed on middle switch 2 to turn on the blower on medium speed and on right switch 3 to turn on the blower on high speed C ON OFF LIGHTING SWITCH Press on this switch to turn on the fluorescent lights and press again to turn them off 10 Broan at 1 rangehoods COM is a division of kitchen accessories U N E t M i T E 8
4. slide their 4 prongs into their corresponding holes in their socket until secured Reinstall the light diffuser HO0099 Z WARNING In order to prevent the risk of personal injury the fluorescent lamps must be cooled down before removing them To remove fluorescent lamps remove the light diffuser and pull fluorescent lamps out of their socket NOTE Some fluorescent lamps may produce a yellowish lighting on first usages This temporary effect will disappear out in time by itself 8 Broan at i rangehoods COM is a division of kitchen accessories U N E t M i T E 8 Call 1 800 667 8721 anywhere in the US and Canada www rangehoods com 10 CLEANING The grease filters bottom panel intake ring A and blower wheel B should be cleaned frequently Use a warm detergent solution The grease filters intake ring and blower wheel are dishwasher safe Clean all metal filters in the diswasher using a non phophate detergent Discoloration of the filter may occur if using phosphate detergents or as a result of local water conditions but this will not affect filter performance This discoloration is not covered by the warranty To remove the blower wheel first take off its intake ring Then remove the blower wheel by pulling it down smoothly NOTE Do not try to remove the black part C attached to the bottom panel When reinstalling the blower wheel make sure the small tab D will fit into one hole
5. Call 1 800 667 8721 anywhere in the US and Canada www rangehoods com 5 INSTALL THE ADAPTER DAMPER CONT D VERTICAL DISCHARGE For a vertical discharge installation only leave the foldable flange C of the adapter damper as is This flange must be located towards the front of the hood See beside ALL INSTALLATIONS Using two 1 2 screws secure the adapter damper to the top or back of the hood Tape the adapter damper to the hood using duct tape to seal it NOTES 1 For the best ventilation performance if a round duct must be used the duct diameter must be 6 or more Use a 3 x 10 to 6 round transition 2 The wall duct must be well prepared to receive the adapter Before performing the installation make sure the adapter fits easily in the duct 6 INSTALL THE HOOD Run power cable to installation location Place the hood at its location Using a pen mark the position of the screws smaller part of the embossed keyholes Remove the hood and install four 1 2 double thread screws at sides locations A leaving a 1 8 gap Place the wire clamp insert the cable in the hood and tighten the wire clamp to secure the cable Place the hood under the cabinet and slide it in position Make sure the adapter damper assembly enters the ducting and the damper opens freely Secure the hood by tightening the screws completely Install the last 1 2 double thread screw B in the remaining embossed hole
6. of the motor STAINLESS STEEL CLEANING HD0156 Do e Regularly wash surfaces with clean cloth or rag soaked with warm water and mild soap or liquid dish detergent e Always clean in the direction of original polish lines e Always rinse well with clear water 2 or 3 times after cleaning Wipe completely dry e You may also use a specialized household stainless steel cleaner e Do not let plaster dust or any other construction residues Don t e Do not use any steel or stainless steel wool or any other scrapers to remove stubborn dirt e Do not use any harsh or abrasive cleansers e Do not allow dirt to accumulate reach the hood During construction or renovation cover the hood to make sure no dust adheres to stainless steel surface Avoid when choosing a detergent Any cleaners that contain bleach will attack stainless steel Any products containing chloride fluoride iodide bromide will deteriorate surfaces rapidly Any combustible products used for cleaning such as acetone alcohol ether benzol etc are highly explosive and should never be used close to a range ENAMEL FINISH Clean with warm water and mild detergent only If discoloration occurs use a good enamel polish such as automotive polish DO NOT use rough abrasive cleaner or porcelain cleaner 9 Broan at rangehoods COM is a division
Download Pdf Manuals
Related Search