Terminal User Manual
Contents
1. 3 10 3 2 Ethernet LAN Test The Ethernet LAN exists of three tasks gt Checking the Ethernet physical layer gt Obtaining the IP address off the computer connected to the IP modem gt Checking the IP address of the computer provided via DHCP by the IPmodem 3 10 3 3 Satellite Connection Test The Satellite connection test is composed of three tests e The Physical layer test checks if the physical layer of the IPmodem satellite connection is able to receive data e The Data link layer test checks if the system is able to send data to the satellite e The Network layer test checks the IP connection 3 10 3 4 Traffic Test The Traffic test is composed of three tests e A ping traffic test tests if ping packets can be transported over the network from the IP modem over the satellite to the hub site The following fields can be filled in Ping packet size bytes minimum 1 and maximum 65 507 bytes Number of pings minimum 1 and maximum 100 e The DNS traffic test resolves a URL via a name server at the hub site The Http GET traffic test verifies the TCP acceleration and pre fetching version 1 0 4 APPENDIX A TROUBLESHOOTING GUIDE complete this section The position of the LEDs described in the Problem indication column is described in section 3 5 Error pe Problem indication Possible solution No connectivity with IP modem web The IPmodem has no connectivity with interface the sate2. Software Check on or alter the software version Hardware Check the Hardware version e Antenna Pointing Repoint your antenna e Test Run tests on the device Status Configuration Ethernet Interface Satellite Interface Multicast Device Software Hardware Antenna Pointing Test Figure 7 Menu Structure for the User version 1 0 10 intersAi 3 4 Reboot the IPmodem See section 2 1 1 for similarities with the hardware button reboot Ethernet Q Satellite Q Software Reboot Figure 8 Location of the Reboot Link gt Click the Reboot link at the right of the status bar to reboot the terminal The terminal will reboot and return to the Status page This may take up to one minute including satellite link initialisation been performed Changes may not take effect until after the next The reboot of the terminal is needed when a re configuration has O reboot 3 5 LEDs in the Status Bar 3 5 1 Ethernet LED The Ethernet LED gives the general status of the Ethernet connection to the IPmodem Connection is not OK Yellow Connection is OK but no DHCP address is given Green A DHCP address is given and the connection is OK Table 4 Status LEDs gt Ethernet version 1 0 m P PR 2 11 interSA 3 5 2 Satellite LED The Satellite LED gives the general status of the Satellite connection to the IPmodem Red No connectivity no valid signal received Yellow A val
3. For more details about the functioning of these buttons and navigation between screens refer to the Point amp Play Setup Manual Pointing Click the Start Pointing button to Start Pointing Click the Skip Pointing button to skip Skip Pointing start the pointing procedure the pointing procedure Do not start pointing without pointing documentation Figure 10 Web Interface gt Status when not Pointed One pointing Carrier version 1 0 l EET F i f z 15 interSA Pointing Click the Start Pointing button to Click the Skip Pointing button to Skip Pointing start the pointing procedure skip the pointing procedure Do not start pointing without pointing documentation When asked by your service provider change the pointing carrier below Pointing Carrier 1 10 8912500 Ghz 22 0000 MBaud ing Carrier 2 11 0000000 GHz 22 0000 MBaud Figure 11 Web Interface gt Status when not Pointed Two pointing Carriers Pointing Click the Pointing Completed button when your antenna is Pointing Completed properly pointed Figure 12 Web Interface gt Pointing Pointing Your antenna is pointed Click the Restart Pointing button to restart the pointing procedure Do not start pointing without pointing documentation Restart Pointing Figure 13 Web Interface gt Antenna Pointing gt Status when Pointed or Pointing is Skipped During normal operation the button is shown via the Antenn
4. 3 7 2 1 Introduction This section describes the interface settings between the terminal and the satellite Every satellite interface setting consists of Initial Receive Carrier This is the initial receive carrier via which the IPmodem will try to gain access to the network version 1 0 19 intersAi Pointing Carrier This carrier is needed to enable antenna pointing via the Point amp Play mechanism When two different pointing carriers are assigned to the terminal the installer can perform his pointing on two different pointing carriers At least one pointing carrier must be enabled 3 7 2 2 View the Satellite Interface Configuration Maximum two initial receive carrier settings and pointing carrier settings can be assigned and displayed Only the settings that are enabled are displayed How to change the satellite interface configuration is described in section 3 7 2 3 If two settings for a carrier are enabled and displayed the preferred initial receive carrier is marked by v If two settings for a carrier are enabled and displayed the default pointing carrier is marked by v The final selection of the pointing carrier that is used for pointing is done in the Status Page as shown in Figure 17 where the non default pointing carrier can be selected In the example of Figure 16 two initial receive carriers and two pointing carriers are enabled Initial Receive Carrier 1 is marked as preferred and Pointing Carrier 2 is
5. For more information about GPL check out our website at http www newtec eu index php id gpl version 1 0 Eee ps 7 interSA
6. Outdoor connection for the transmit coax cable 3 Outdoor connection for the receive coax cable Table 3 Description Elements of the iLNB version 1 0 intersAi 3 TERMINAL WEB INTERFACE 3 1 Prepare the Settings of Your Computer Check if your computer is set to DHCP This way the computer can receive an IP address from the IPmodem Follow the procedure in Appendix D Settingg and Changing your IP Settings in the Point amp Play Setup Manual to check and or change your IP settings 3 2 How to Access the Terminal Web Interface 3 2 1 version 1 0 With Satellite Connection In the normal operational mode a connected computer should be configured in DHCP mode to retrieve an IP address automatically and to retrieve the DNS server The terminal acts as a DHCP server for the computer Browse to the web interface gt Type the IPmodem s address in the address bar of the browser 192 168 1 1 You will be re directed to the Status page of the terminal Figure 5 The I Pmodem s Address in the Address bar of the Browser interface See Appendix C Local Network Configuration in the Alternatively use the Default Gateway address to reach the web Point amp Play Setup Manual It is possible that during first logon the terminal will perform an upgrade with the latest software since you cannot login using the old SW This process can take up to ten minutes You may NOT interrupt the terminal yourself dur
7. 10 2 Filed Test Results Click on the button to export the file As a result a web page with the test results in text format will be provided The test results can now be saved in a text file from the browser as shown in Figure 31 i http 192 168 1 1 cei binfexport test report Windows Internet Explorer lt J j F http f 192 168 1 L cgi binfexport test report sd Edit View Favorites Tools Help New Tab Ctrl T New Window Ctrl N Open Chrl O Clase Tah Ctr 00 06 39 00 B A0 NTC 2218 US Page Setup 07041303510 Print Ctrl P 22 09 37 up 4 days 22 09 load average 0 33 0 16 0 17 Print Preview Send Import and Export Properties GREEN work Offline RED GREEN satellite network lookup Error State No demodulator lock Software Version z 1 5 1 3 1 Ethernet Eth MAC Address 00 06 39 00 B6 A1 Management IP Address 192 168 1 1 Netmask E fees ede UD 2 Satellite interface Initial Receive transponder Transport Mode DVB 52 CCM Frequency 10 8912500 GHz Symbol Rate 22 0000 MBaud DVB 5 FEC Code Rate auto DVB 52 Roll off Factor 25 Population ID 5 Multicast mode 5 5 lg Figure 31 Web Interface gt Test gt Export to Text File 3 10 3 Test Descriptions This section provides an overview of the tests that can be run on the IPmodem 3 10 3 1 Software Test The Software test verifies the validity of the software version 1 0 34 interSA _
8. Satellite Interface TX 8816 69 1 1 Figure 9 Status Page when the Terminal is Pointed When the terminal is not yet pointed a third part is shown e Pointing This part gives an overview of the pointing status and pointing carrier selection version 1 0 13 inter SA 3 6 2 3 6 2 1 3 6 2 2 version 1 0 Overview Modem State The IPmodem state is indicated by a coloured LED and a state description For the LED colour code refer to Table 7 The possible modem state descriptions are given below Modem state Awaiting installer action satellite network lookup Synchronising Synchronised Network login Operational The terminal is waiting for an action of the installer The terminal is looking for the satellite network The terminal found the satellite network and time synchronisation The terminal is synchronised and can directly log in on the satellite network when IP traffic is received via the Ethernet interface The terminal is trying to log in on the satellite network The terminal is logged in Table 7 Status Page gt Modem State Demodulator The Demodulator state is indi LED colour code cated by a coloured LED and a state description The demodulator is locked The demodulator is not locked Table 8 Status Page gt Demodulator LED The demodulator state is built as follows see Table 9 for more details e 95 0 dBM Es No 23 2 dB lt Satellite n
9. Static Multicast Mode Table 13 Configuration Page gt Multicast parameters version 1 0 24 intersAi Reboot 3 7 3 3 Edit the Multicast Configuration Newtec 5 00 06 39 00 A3 57 a El SHAPING THE FUTURE OF SATELLITE COMMUNICATIONS ar _ 4 Expert Log out out Ethernet amp Satellite amp Software Reboot Menu o Configuration for Multicast Status Configuration Ethernet Interface o Receive Multicast Satellite Interface 6 Multicast gt Multicast Mode Disabled Static IGMP Dynamic Skei Static Multicast IP Address Software Hardware Static Multicast IP Address Antenna Fointing ssaa Static Multicast IP Address Static Multicast IP Address Static Multicast IP Address Static Multicast IP Address Static Multicast IP Address Static Multicast IP Address Static Multicast IP Address Static Multicast IP Address Back Save Figure 21 Web Interface gt Edit Multicast Configuration gt Click on in the Web Interface gt View Multicast configuration Figure 20 to Change the Ethernet Settings gt Edit the parameters to be changed gt Click on SAVe in the Web Interface gt Edit Multicast configuration Figure 21 to save the new settings The Multicast configuration is now saved The response screen for a Disabled Multicast configuration version 1 0 25 intersAi Air MAC adi S 00 06 39 00 A3 57 Newtec I SHAPING THE FU
10. line s Notices gt This product was qualified under test conditions that included the use of the supplied cable between the components To be in compliance with regulations the user must use this cable or equivalent and install it properly gt Different types of cord sets may be used for connections to the main supply circuit Use only a main line cord that complies with all product safety requirements of the country of use gt Installation of this product must be in accordance with national wiring codes In some countries authorisation is needed for satellite reflector installation Call your local authorities in case of doubt version 1 0 a ma afs 6 interSA TABLE OF CONTENTS PTO AE NS MU ii UME ii Version history and applicability ccccccsssseceeeeeeeeeeeeeseeeeeeeesseeeeeeseeeeeeeeeeesaaseeees ii Related documentation ccccccccccseeeeceeecaeeeceeeceeeseeeeesseaeceesseaaeeeessueaeeeeessaaneeeeeeeas 1 F 910 Del 0 ES lil Software versions cccccccccccccaeeeeecceeeeecaeeeseeceeeeeeeeeeseeeceeeeeseueeaeeeeeseesseaeeeeseeeeesaaas iii FDL lil Important Safety Pr caullonsuauvasssmsuamninnmnsseiinnene iv WY ATIC SEE tenieetdienreans IV ME V NU Sarsa r E E EE E E R vi Tabe Ol COMENTS goca N vii 1 BPA UE OCC IO i aa 1 EE E S 1 OE EE EE EE NE NE AAE 1 En 1 1 3 About the Sat3Play Terminal rrrrrrnnnnnnnnrrnnnnnrvnnnnnnnnrvnnrnnnnnrnnrnnnnnnsennnnnnsnsnnn 2 1 4 Install
11. set as default Configuration for Satellite Interface Initial Receive Carrier Initial Receive Carrier 1 Initial Receive Carrier 2 Preferred v Transport Mode DVB 52 CCM DVB 52 CCM Frequency 10 8912500 GHz 11 9535000 GHz Symbol Rate 22 0000 MBaud 27 5000 MBaud DVB S2 Roll off Factor 25 25 Pointing Carrier Pointing Carrier 1 Pointing Carrier 2 Default wi Transport Mode DVB S2 CCM DVB S2 CCM Frequency 10 8912500 GHz 11 9535000 GHz Symbol Rate 22 0000 MBaud 27 5000 MBaud DVB 52 Roll off Factor 25 25 Orbital Position 23 5 East 23 5 East Figure 16 Web Interface gt View Configuration Satellite Interface l EET F a i i J in j JA nl i e nt MN i 3 7 2 3 The Parameters of the Satellite Interface version 1 0 21 The displayed parameters and their descriptions are shown in the table below Initial Receive Carrier Preferred Mark for the preferred Initial Receive Carrier Transport Mode DVB S DVB S2 Constant Coding Modulation CCM Frequency Initial receive frequency GHz Symbol Rate Initial receive symbol rate Mbaud DVB S2 Roll off Factor Only configurable in DVB S2 mode Excess bandwidth of the Rx signal spectrum 35 25 Ao 20 Pointing Carrier Default Mark for the default pointing carrier Transport Mode DVB S DVB S2 Constant Coding Modulation CCM Frequency Initial receive frequency GHz Symbol Rate Initial receive symbo
12. than four hours Error information in the web interface The activation of the installation carrier Installation carrier setup failed test mode failed because the terminal was LED error indication not in the correct state Warning LED is on RX LED is on Table 17 Troubleshooting Table version 1 0 38 interSA 5 APPENDIX B ACRONYMS Acronym term 8PSK gt gt LS JIOJO UIO gt lt BER C N CCM CE approved O DHCP lt DVB RCS DVB S DVB S2 EIRP O GMSK G Q Cc 4 4109 iim A p U UO ki U O 4 uy HTTP ICMP IEEE iLNB LAN version 1 0 39 Description 8 Phase Shift Keying Alternating Current Access Control Server Address Resolution Protocol Asynchronous Transfer Mode Bit Error Rate Carrier to Noise ration Constant Coding Modulation Conformit Europ enne European health amp safety product label Direct Current Dynamic Host Configuration Protocol Digital Video Broadcasting Digital Video Broadcasting Return Channel Satellite Digital Video Broadcasting over Satellite 2 Effective Isotropic Radiated Power ETSI Norm Frame Composition Table Forward Error Correction File Transfer Protocol Gaussian Minimum Shift Keying Antenna Gain to System Noise Temperature Ratio Graphical User Interface Hyper Text Transfer Protocol Internet Control Message Protocol Institute of Electrical and Electronics Engineers Interactiv
13. to be successful is for the terminal to have satellite connectivity during the time of upgrade To allow a secure terminal software upgrade mechanism the flash of the modem can contain two different software versions A newly installed software version has to pass an automatic software validation procedure After a software upgrade the IPmodem is automatically reset BS 00 06 39 00 9F 31 FSH AR Sg ee nec COMMUNICATIONS Legged in from Hub Ethernet Q Satellite Q Software Reboot Menu Software Status Configuration Software Version Currently Running Software Version 1 9 8 9 Alternate Software Version 1 9 8 0 Ethernet Interface Satellite Interface Multicast Device Hardware Antenna Fointing Test Figure 24 Web Interface gt View Software Configuration version 1 0 27 intersAi Table 14 gives a description of the parameters in the Software menu Software Download Identifiers To uniquely identify the terminal variant for software download triggered from the hub side the following keys are reserved for SW update Software Download Software download manufacturer Identifier 639 for Manufacturer ID Newtec devices Software Download Software downloads hardware Identifier Hardware ID Software version Currently Running The currently installed software version is displayed Software Version When an alternate software version is available you will be provided with a link Tr
14. 220 EE SE 13 3 6 1 MOGUC ION EEE EEE see 13 262 NNN 14 3 6 2 1 Modem State wi ccccccccccccsssccnccceecsscessssnecscesencdssssseececdsccesesdeseeesessasededeneeesecenas 14 3 6 2 2 Demodulator cccceccecccccseeeceeccseseceecceesseeeseesauseeeeseeaueceeessaaeeeeessaaeeeess 14 NOEN 15 3 6 2 4 Software Version sedasie innar anandia NEENA Eaa AKE iaaiiai 15 3020 FANN 15 3 6 3 Interface Statistics sansene Uotesanesaceeaesnenesecbeeecs 16 TN 18 3 7 1 Ethernet Le ee EEE NN 18 3 7 1 1 View the Ethernet Interface Configuration rrrnnnrnrnrrrnnnnnrrnrrnnnnnrnnvnnnnnne 18 3 7 1 2 The Parameters of the Ethernet Interface rrrnrrrrrvnnnnnnrrvvrnrnnvrrvrnnnnnenn 18 3 7 1 3 Modify the Ethernet Interface Configuration cccccseeeeeeeseeeeeeeeeeeeens 19 3 2 SUE 19 Sr 100 Go ON EEE EE EEE ENE 19 3 7 2 2 View the Satellite Interface Configuration vrrrnnnrrrrrrrnnnnnrrrrrnnnnrernvnnnnnre 20 3 7 2 3 The Parameters of the Satellite Interface rrrnrrrnnnnrrnnvvnnrrrnnnnrrnnnnnnnn 21 3 7 2 4 Edit the Satellite Interface Configuration rrrrnnrrrerrrnnnrnrrrrrnnnnnvnnnnnnnnee 22 gt EEE OMICS EEE EN 23 3 7 3 1 View the Multicast Configuration rxvrrnnnnrrnevnnnnnrrvennrnnnrreennnnnrrreennnnnenn 24 3 7 3 2 The Multicast Parameters rrrnnnnrrrnrnnnnvnnnnnnrnnrnnnnrnnnnnnrnnnnnnsennnnnnrnnnnnnnen 24 3 7 3 3 Edit the Multicast Configuration rrrrerrrrnnnnnnnnrrrnrrrrnnnnnrnrrvnnnrnnnnnnnnn
15. 3Play modem installation until there is no risk of thunderstorm or lightning activity in the area version 1 0 interSAi gt To prevent electrical shock do not connect the plug into an extension cord receptacle or other outlet unless the plug can be fully inserted with no part of the blades exposed gt The in line power supply input power cord must be connected to a properly grounded three prong AC outlet Do not use adapter plugs or remove the grounding prong from the plug gt The in line power supply inout power cord may not be used when damaged in any way Cautions A caution is defined as a procedure or practice that if not correctly followed could result in equipment damage or destruction D Always observe the following cautions Not following these cautions will cause the warranty to be invalid gt Always use the in line power supply with the Sat3Play modem Using a different power supply may cause equipment damage gt To ensure regulatory and safety compliance use only the provided power and interface cables or cables which conform to the specifications within this manual gt Do not open the unit Do not perform any actions other than those contained in the installation and troubleshooting instructions Refer all servicing to qualified service professionals gt Avoid damaging the Sat3Play modem with static electricity by first touching the coaxial cable connector when it is attached to the earth
16. TURE OF SATELLITE COMMUNICATIONS oe SEE 2 EL Ethernet Q Satellite Software Reboot Se Committed Multicast Configuration Configuration Ethernet Interface i Satellite Interface Multicast Mode Disabled o Multicast All Static Multicast IP Addresses are ignored in this mode Device Software Hardware Antenna Pointing Installation Carrier Logfile Diagnostic Report Test Figure 22 Web Interface gt Confirmation of Disabled Multicast Configuration In case an invalid multicast IP address is replacing a valid multicast IP address the last valid multicast IP address will still be in use The response screen for a Committed Multicast configuration Newtec Air MAG address 00 06 39 00 A3 57 ae gr VG os a SHAPING THE FUTURE OF SATELLITE COMMUNICATIONS ge Expert Log out Ethernet Satellite Q Software Reboot imi Committed Multicast Configuration Configuration Ethernet Interface 9 Satellite Teter ace Multicast Mode Static o Multicast gt Static Multicast IP Address 225 0 55 55 Device Static Multicast IP Address 738 1 1 1 Software Hardware Antenna Pointing Test Figure 23 Web Interface gt Confirmation Committed Multicast Configuration version 1 0 26 intersAi 3 8 Device 3 8 1 Software 3 8 1 1 Introduction General Case The terminal software is automatically upgraded over the satellite without any user interaction In general the only requirement for an upgrade
17. a Pointing button in the menu bar and should only be used in case pointing documentation is available and the antenna must be re pointed 3 6 3 Interface Statistics Interfaces Ethernet User side interface Ethernet frames interface Satellite Satellite side interface IP packets interface Statistics Bytes Total number of received or transmitted bytes Received or transmitted Ethernet frames version 1 0 o m af 16 inter gt SA or IP packets EE of occurred errors Dropped Dropped Ethernet frames or IP packets Table 10 Status Page gt Interface Statistics version 1 0 p 17 interSA I 3 7 Configuration been performed Changes may not take effect until after the next The reboot of the terminal is needed when a re configuration has reboot 3 7 1 Ethernet Interface This section describes the interface between the computer and the IPmodem 3 7 1 1 View the Ethernet Interface Configuration N ewtec address 00 06 39 00 43 57 SHAPING THE FUTURE OF SATELLITE COMMUNICATIONS dn mett Log out En Satelite r Software Reboot Configuration for Ethernet Interface Status Configuration Ethernet Interface Satellite Interface Multicast Eth MAC Address 00 06 39 00 A3 58 Device Management IP Address 192 168 1 1 Software Netmask 255 255 255 0 Hardware z yous Edit Antenna Pointing Test Figure 14 Web Interface gt View Configuratio
18. ated document or a web link Version history and applicability Document Subject J Comments version version Related documentation The details of the installation and pointing of the reflector are described in the Point amp Play Setup Manual version 1 0 r 3 mu e Pim m oa F _ A h FJ WS il wF Product range S3P im Ku band VSAT Antenna Software versions R1 9 Feedback Newtec encourages your comments concerning this document We are committed to providing documentation that meets your needs Please send any comments by contacting us at documentation newtec eu Please include document and any comment error found or suggestion for improvement you have concerning this document version 1 0 l F e A y 3 interSA SSS aes IMPORTANT SAFETY PRECAUTIONS Install the IPmodem and antenna according to local regulations IA For the US market please visit the Federal Communications Commission s website at www fcc gov gt Before installing the IPmodem please make sure that your electrical outlet is properly wired and your computer equipment is properly grounded Consult with a licensed electrician if in any doubt gt Please read and understand all operating instructions in your user s guide located in the IP modem shipping box gt Please read and understand all of the safety precautions set forth in this user manual and in the user s guide prior to connect
19. ation Tasks iwiatcesncitavomnendaitesitacdeduntcndadustestsitententdbaniacdsiusteaiinanastsieuntaatdbenaariud 3 2 Getting to know your Sat3Play Terminal ernnnnnnnnrnnnnnnnnennnnnnnnnennnnnnnnvennnnn 4 2l WAS PENN ne 4 2 1 1 The IPmodem Front Panel cccccccccsssseeeeeceeseceeeeseaeeeeeessaeeeeeeeesaaeeees 4 2 1 2 The IPmodem Back Panel r rrrrrnnnnnnnnnrvnrnnnnnnevnvrnnnnnennnnnnnnnrnnnnnnnnnsnnnnnnsnee 5 eames 1129 See tee ene eee ee on ee ee ee eee ee 6 3 Terminal Web Interface LuLL2aasgdnsstannesd add 7 3 1 Prepare the Settings of Your Computer rrrrrrnrrrnvrennnrnvrvnnnvnrrnnnrrnrrnnsrrrrrnnrrnnn 7 3 2 Howto Access the Terminal Web Interface rrrrrrnnnrnrrnrnnnnrnrrnrnnnnnnennnnnnnnrr 7 3 2 1 With Satellite Connection rrrannnrrnnrrnnnnrrvnrrnnnnrrvnnnnnnnnrnnnnnnnnsrnnnnnnnnssnnnnnnsnee P 3 2 2 No Satellite Connection rwrrrrrnnnnnnnovvrnrrrnnnnnnrrrrnrrrrnnnnnnsrrernrrnnnnnnnssrnnnnnnnnnn 8 3 3 Overview Web Interface rrrnrnnnnnnrrnnrnnnnnrrnrrnnnnnrrnnrnnnnnrrnnnnnnnnsennnnnnnnssnnnnnnsnee 9 3 3 1 ETE ET OUT EE ME 9 EEE 0 on EE EEE EN 9 3 4 Reboot the IPmodem ccccceecccceccseeeeceeeeaeeeeeeeesueeseeeeesaeeeeeeesaaeeeeeeesaaeeeees 11 3 5 LEDS IN 1ING Status Bar x opcsdesdcoctsacesace eotccencserenaceenaswettacesacs oot ascneseceeucsnenesecbuends 11 3 5 1 Enom GE DE 11 version 1 0 So m3 15 1 2 LED Rea ee eee eee 12 ooo PWE EED Dee nee ee ee eee eee een eee 12 eS
20. ation process failed Reset the IPmodem section 3 4 Contact your ISP if this error is persistent for more than four hours The error can be an indication of a general network problem The time synchronisation is lost Reset the IPmodem section 3 4 Contact your ISP if this error is persistent for more than four hours The error can be an indication of a general network problem The IPmodem could not login to the satellite Verify if the TX cable is correctly connected If the TX cable is correctly connected and the error is still occurring after a number of hours contact your ISP to report the problem to check if your IPmodem is provisioned in the network An error occurred during the configuration of the network layers after a valid satellite network login Reset the IPmodem section 3 4 Contact your ISP if this error persists and provide them with any additional error information displayed An error is detected in the TCP acceleration service Reset the IPmodem Reset the IPmodem section 3 4 Contact your ISP if this error is persistent for more than four hours interSAi Problem indication Possible solution Error information in the web interface The connectivity with the satellite network Network connectivity lost is lost Reset the IPmodem LED error indication Reset the IPmodem section 3 4 Warning LED is on RX LED is on Contact your ISP if this error is persistent for more
21. ay Terminal documentation exists out of the following e Point amp Play Setup Manual e Antenna Pointing Information e One CD containing Terminal User Manual Point amp Play Setup Manual Antenna Pointing Information version 1 0 ERA e PR 2 1 interSA 1 3 About the Sat3Play Terminal The Sat3Play Terminal is state of the art equipment allowing cost effective plug amp play connection to an extended variety of IP based applications The Sat3Play Terminal consists of e Asmall size high quality easy to install satellite antenna 1 m e An interactive LNB iLNB e An IPmodem providing an Ethernet connection to the computer of the end user or Local Area Network LAN The interactive iLNB low power equipment is light weight easy to install and highly reliable All parts are built using state of the art microwave design that guarantees an unequalled reliability for many years Connected to the interactive iLNB by means of transmit and receive cables the high speed IPmodem provides an asymmetrical 2 way broadband access to IP applications e g Broadband Internet Access Its small size in line with the best practice in the telecom and IT industries makes it suited for any type of user business or consumer Figure 1 Sat3Play Terminal interSA 1 4 Installation Tasks To ensure proper installation of the Sat3Play Terminal the following tasks must be performed These tasks are described i
22. ctor O35 25 O20 O35 2725 020 Orbital Position 2305 b East O west 235 b East O west Warning Entering incorrect settings will prevent your modem to logon to the network Only change satellite configuration settings on request of your Internet Service Provider Figure 17 Web Interface gt Edit Configuration Satellite Interface gt Click on Sae in the Web Interface gt Edit Configuration Ethernet interface Figure 17 to save the new settings The satellite interface configuration is now saved and the changes in the configuration are displayed version 1 0 a z inter SA Changing initial carrier 2 frequency from 40000000 to o Changing initial carrier 2 symbol rate from 200000 to o Changing pointing carrier 2 frequency from 110000000 to o Changing pointing carrier 2 symbol rate from 220000 to o The configuration was updated Changes may not take effect until after the next reboot Figure 18 Example of Satellite Interface Configuration Changes gt Click on reboot at the bottom of the page gt Click on Normal Reboot to confirm and execute the reboot Reboot The Modem will restart in a few seconds Click here to return to the web interface Figure 19 Reboot in Progress gt Click on Click here to return to the web interface and wait a few minutes The satellite interface configuration is now effective 3 7 3 Multicast The satellite can send several sess
23. e Low Noise Block down converter Internet Protocol Internet Service Provider Information Technology Local Area Network interSA version 1 0 40 Acronym term LED LNB iLNB MAC address MF TDMA MPEG NCR NIT OIZ 3 D PAT PMT QPSK C J Cp UD I T O 02 x T T J 4 M J J 3 A C DT SEMS TBTP TCP TCP IP C M op 4 ep 4 4 x 10 U C I D A VSAT WCT lt O Table 18 Acronyms Description Light Emitting Diode Low Noise Block down converter Medium Access Control Multi Frequency Time Division Multiple Access Moving Picture Experts Group Network Clock Reference Network Information Table Newton metre Outdoor Unit Program Association Table Program Map Table Quadrature Phase Shift Keying Return Channel Satellite Radio Frequency Request for Comments RCS Map Table Reporting Tool Receive Satellite Access Provider Superframe Composition Table Service Descriptor Table Satellite Earth Station Management System Time Burst Time Plan Transmission Control Protocol Time Composition Table Terminal Management System Transport Stream Transfer User Datagram Protocol Volts Alternating Current Very Small Aperture Terminal Waveform Composition Table interSA 6 APPENDIX C LICENSES GNU software is used in this product You can download GNU Wget from the following location http www gnu org software wget
24. et LAN test Ethernet test Satellite connectiontest Physical layer test Data link layer test Network layer test Traffic test Ping traffic test Ping packet size bytes Number of pings DNS traffic test Http GET traffic test Starttest Figure 29 Web Interface gt Test Overview Mark H or unmark L a test depending on the tests to be run Section 3 10 3 gives a description of the tests which can be performed Click on the Sterttest_ button to begin the test version 1 0 l F A y 32 interSA 3 10 1 On Screen Test Results As a result a screen with the requested test results will be shown see Table 16 Possible States of IP modem Tests Successfully ran test Test waiting to run Unsuccessfully ran test Tests Tests started 18 seconds ago Software test W Software test Ethernet LAN test I Ethernet test Satellite connection test I Physical layer test f Data link layer test W Network layer test Traffic test i Ping traffic test Ping packet size bytes Number of pings M DNS traffic test Http GET traffic test Start test Export to text file Figure 30 On Screen Test Results Table 16 Possible States of I Pmodem Tests v running software wersion 1 7 10 0 link up 100baseTx FD v 1 packets transmitted 1 packets received 0 packet loss round trip min avg max 1561 9 1561 9 1561 9 ms v v 3
25. etwork name gt Demodulator label value Indication of the received signal strength expressed in dBm This indication can change when going from pointing mode to operational mode Es No is an indication of the received signal quality expressed in dB This indication can change when going from pointing mode to operational mode Table 9 Status Page gt Demodulator Labels interSA 3 6 2 3 Info by Error State An error message can be displayed This error message displays the current error status and will be reset when the terminal has entered the satellite network and the terminal is operational Please refer to for more details on possible errors and actions needed to resolve the occurring error 3 6 2 4 Software Version The running software version is indicated by its version number 3 6 2 5 Pointing This section of the web interface displays information on the pointing status of the terminal The following status can be viewed e Status when the antenna is not pointed as shown in Figure 10 giving the option to start pointing or to skip pointing Where two pointing carriers are available one can choose the used carrier as shown in Figure 11 e Status during the pointing of the antenna see Figure 12 Click on Pointing Completed when the antenna is pointed e Status when pointed successfully or pointing skipped as shown in Figure 13 This is the status during normal operation of the terminal after pointing
26. grounded coaxial cable wall outlet Always first touch the coaxial cable connector on the Sat3Play modem when you are disconnecting or re connecting your Ethernet cable from the Sat3Play modem or your computer gt To prevent overheating do not block the ventilation holes on the sides and top of the unit gt Only wipe the unit with a clean dry cloth To avoid equipment damage never use fluids or similar chemicals Do not spray cleaners directly on the unit or use compressed air gas to remove dust version 1 0 Taa 6 m At a FF F 5 a fF A gt The user should install an AC surge arrestor in the AC outlet to which this device is connected This avoids damaging the equipment by local lightning strikes and other electrical surges gt This antenna is more than 1 square metre wind pressure equivalent area Do not make an installation in bad weather conditions gt Secure tight all parts to avoid any potential danger to persons and Surroundings gt If faced with a critical situation in which personal safety is in jeopardy do not try to keep hold of the antenna gt For safety reasons ensure that you are not near any power line gt Make sure a minimum distance of 6 metres 20 feet separates the antenna from any power line gt Before digging in case of need for a penetrating antenna mast contact your local authority to check for information regarding any underground cables and power utility
27. id signal was received The terminal is busy logging in on the satellite network Green The system is operational and the user is logged in on the satellite network Table 5 Status LEDs gt Satellite 3 5 3 Software LED The Software LED gives the general status of the installed software or the updates The terminal has a newer software version than the running software version and The newer software version was not selected because the software validation process failed see for possible actions and follow up Yellow The terminal is retrieving new software via satellite This can take up to 10 minutes No problem The terminal is running with the latest software version Table 6 Status LEDs gt Software version 1 0 K interSAi 3 6 Status Page 3 6 1 Introduction In normal operation when the terminal is pointed and active there two parts to the Status Page as shown in Figure 9 which are described in more detail in the following sections e Overview This part gives an overview of the Pmodem demodulator and software state e Interface Statistics This part gives an overview of the IP modem statistics Status Overview amp Modem State operational Q Demodulator 58 7 dBm E_ N 17 0 dB Software Version 1 7 12 0 Interface Statistics Interface bytes packets errors dropped RX 656066 6236 0 0 Ethernet Interface TX 11716080 6142 0 0 RX 16822 198 0 0
28. ing any cables to the IPmodem gt Safety and installation rules are given in standards regarding cabled distribution systems for television and interactive multimedia signals EN 50083 1 The installer must follow these rules to be conform to the law Always implement regulations as issued by national and local authorities Warnings A warning is defined as a procedure or practice that if not correctly followed could result in injury death or long term health D hazard Always observe the following warnings Not following these cautions will cause the warranty to be invalid gt There are no user serviceable parts in your system There are potentially lethal voltages inside the equipment It should only be opened by a technician trained and certified to service the product gt RF Radiation Hazard The transmitting equipment is capable of generating RF levels above the maximum permissible exposure level Do not enter the radiation beam of the transmitter feed horn and or antenna reflector when the transmitter is on gt Keep the space between feed horn and reflector clear gt When the Sat3Play modem is powered on DC voltages are present on the rear panel Tx and Rx connectors gt To prevent fire or shock hazard do not expose this appliance to rain or moisture The apparatus must not be exposed to dripping or splashing and no objects filled with liquids such as vases should be placed on the apparatus gt Postpone Sat
29. ing this period e g by rebooting or powering down If newer software is available the terminal will e Download this software e Install this software e Reboot the terminal e Logon to the network again interSA 3 2 2 No Satellite Connection Make sure your computer is able to receive an IP address via DHCP by following the procedure Appendix D Setting and Changing your IP Settings in the Point amp Play Setup Manual When the terminal is not linked to the satellite network after three minutes the computer will automatically receive its IP address via DHCP from the IPmodem and you will then be able to browse the web interface If no DHCP address is assigned to your terminal remove the Ethernet cable from your computer wait a few seconds and plug the Ethernet cable back into your computer gt Type the IPmodem s address in the address bar of the browser 192 168 1 1 You will be redirected to the Status page of the terminal If the problem remains you need to assign a static IP address to your computer by following the procedure in Appendix D Setting and Changing your IP Settings in the Point amp Play Stup Manual n l amar a e JER i i 5 in j 2 ill aa i q nt MN 3 3 Overview Web Interface 3 3 1 General Layout Newtec Air MAG T 0 06 39 00 A3 57 J SHAPING THE FUTURE OF SATELLITE COMMUNICATIONS y Ethernet Configuration Ethernet Interfa Satellite Interface a
30. inter SA Terminal User Manual for interS AT version 1 0 2009 Newtec cy The material contained in this document is confidential and intended for use only by parties authorised by Newtec All Rights Reserved No part of this document may be photocopied reproduced stored in a retrieval system or transmitted in any form or by any means whether electronic mechanical or otherwise without the prior written permission of Newtec cy Newtec cy Laarstraat 5 9100 Sint Niklaas Belgium General 32 0 3 780 65 00 www newtec eu Fax 32 0 3 780 65 49 General general newtec eu version 1 0 ABOUT THIS MANUAL This User Manual is intended for the user of the Sat3Play Terminal It provides safety precautions a description of the Sat3Play Terminal and a detailed description of how to use the GUI Graphical User Interface First line troubleshooting information is also included Cautions and symbols The following symbols appear in this manual A caution message indicates a hazardous situation that if not avoided may result in minor or moderate injury It may also refer to a procedure or practice that if not correctly followed could result in equipment damage or destruction your equipment including helpful hints shortcuts or important A hint message indicates information for the proper operation of O reminders A reference message is used to direct to an internal reference within the document a rel
31. ions to a number of Sat3Play Terminals at the same time This is IPmulticasting There are two configurations possible in the Sat3Play Terminal to receive these programs e Static IP addresses these are IP addresses where the sessions are received You will be provided with these addresses if needed e IGMP this is a protocol that lets you receive multicast sessions maximum 10 without entering specific IP addresses version 1 0 l p s 5 i f z 23 interSA 3 7 3 1 View the Multicast Configuration Newtec FSHAP IG SWE EN GNERLTE COMMUNICATIONS Ethernet amp Satellite amp Software Downloading SHOP 00 06 39 00 A3 57 er Expert Log out Menu o Configuration for Multicast status Configuration Ethernet Interface Satellite Interface me Device Softvare Hardv re Antenna Pointing Test Receive Multicast Multicast Mode Static Static Multicast IP Address 225 0 55 55 Static Multicast IP Address 238 1 1 1 Figure 20 Web Interface gt View Configuration Multicast 3 7 3 2 The Multicast Parameters The displayed parameters and their description are shown below Parameter Multicast Mode Static Multicast IP Address 1 10 Disabled Multicast mode is disabled Static The active Multicast Configuration is based on entered Static Multicast IP Addresses IGMP Dynamic Dynamic IGMP multicast mode Maximum 10 multicast IP Addresses can be assigned and active in case of
32. l rate Mbaud DVB S2 Roll off Factor Only configurable in DVB S2 mode Shape of the Rx signal spectrum 35 25 Ao 20 Orbital Position Orbital position of the satellite in degrees and East West selection Table 12 Configuration Page gt Satellite Interface Parameters gt Initial Receive Carrier interSA 3 7 2 4 Edit the Satellite Interface Configuration gt Click on in the Web Interface gt View Satellite Configuration Interface as shown in Figure 16 gt Edit the parameters to be changed and as described in Figure 17 An initial receive carrier setting or pointing carrier setting can only be enabled if the frequency of the configuration is filled in Configuration for Satellite Interface Initial Receive Carrier Initial Receive Carrier 1 Initial Receive Carrier 2 Preferred Carrier 1 Carrier 2 Enabled Enabled Disabled Enabled Disabled Transport Mode Opve s pve s2 CCM Opve s pDve s2 CCM Frequency 10 8912500 GHz 11 j9535000 GHz Symbol Rate 22 j0000 MBaud 27 5000 MBaud DVB S2 Roll off Factor O35 25 O20 O35 25 O20 Pointing Carrier Pointing Carrier 1 Pointing Carrier 2 Default Carrier 1 Carrier 2 Enabled Enabled Disabled Enabled Disabled Transport Mode Opve s C pvB s2 CCM O pvB S C pvB s2 CCM Frequency 10 8912500 GHz 11 j9535000 GHz Symbol Rate 22 j0000 MBaud 27 15000 MBaud DVB S2 Roll off Fa
33. llite network section 3 2 2 LED error indication Check if the computer can receive an IP The Rx indicator LED is off address via DHCP as described in Section 1 If the computer can receive an IP address unplug the Ethernet cable from your computer wait for more than three minutes and plug the Ethernet cable in again O We would appreciate any useful feedback that can help us to The Warning LED is orange Web interface error info Your antenna is not pointed Consult the Modem State Point amp Play Setup Manual to execute the Awaiting installer action pointing process Modem LED is red Web interface error info Your modem is currently in the pointing Modem State antenna pointing state Consult the Point amp Play Setup Manual to execute the pointing process Web interface error info Error in handling of the Rx signal The Rx No demodulator lock demodulator cannot lock Modem LED is red Verify the pointing of the antenna LED error indication Verify the connectivity between the The RX indicator LED is off IPmodem and the antenna Verify the configuration of the satellite interface frequency polarisation symbol rate Web interface error info The modem is determining on which Terminal specific forward carrier traffic carrier it is provisioned If lookup is ongoing the message does not disappear within LED error indication 10 minutes reset the modem Warning LED is on RX LED is on section 3 4 If the err
34. lternate Version Test Note Try alternate version restarts the Modem NOTE Try alternate version restarts the Modem Figure 25 Web Interface gt Software Alternate Version To re trigger the validation process gt Click the link Try Alternate Version The Software Upgrade page will be displayed indicating the new software version number see below gt If the web interface doesn t refresh automatically navigate back to the Status page A total reboot including satellite link initialisation might take up to 10 minutes Newtec Air mAg address 00 05 39 00 B2 2A SHAPING THE FUTURE OF SATELLITE COMMUNICATIONS Ethernet Q Satelite Q Software Reboot Software Upgrade E a status Alternate Software wersion 1 9 8 0 will be used Configuration Ethernet Interface The Modem will restart in a few seconds Satellite Interface Multicast Device Hardware Antenna Pointing Test Figure 26 Web Interface gt Software Upgrade Confirmation version 1 0 20 interSA _ When a newer version is present and validation fails the software LED is red E Also read section 3 5 for more information on the meaning of the software status LEDs 3 8 2 Hardware Newtec Air MAC SE 2 nl SHAPING THE FUTURE OF SATELLITE COMMUNICATIONS Ethernet Satellite Software CO Hardware Status Configuration Hardware ID NTC 2218 US Ethernet Interface Hardware Version 1 Satelli
35. mp Modem State synchronising Multicast Demodulator 53 3 dBm E N 17 1 dB Device Software Version 1 7 10 0 Sortwere Hardware Antenna Pointing Interface Statistics EEE a Interface bytes errors dropped 24399 Ethernet Interface 62097 0 Test stem Interface 0 Figure 6 Page Layout of Web Interface Each of the web interface pages contains the same elements e A Banner The banner contains the Newtec logo and shows the Air MAC address B Status bar The status bar always shows the most important status LEDs This information will be specified in the body of the Status page e C Menu structure On the left hand side of the page the site navigation is found Click an item to select it The menu structure may differ depending on your login status e D Body The actual content of the web interface is shown in the body It always shows the page title and one or more content blocks or forms 3 3 2 Menu Structure The menu structure of the web interface of the web interface is described below see Figure 13 e Status Check on the device and network status e Configuration Ethernet Interface Check and alter the Ethernet interface configuration version 1 0 Reboot o interSA _ Satellite Interface Check and alter the Satellite interface configuration Multicast Check and alter the Multicast configuration e Device Interface
36. n Ethernet I nterface 3 7 1 2 The Parameters of the Ethernet Interface The displayed parameters and their description are shown below Eth MAC address MAC address of the Ethernet interface Management IP Management IP address of the Ethernet interface address Netmask Network range for the user s LAN Table 11 Configuration Page gt Ethernet Interface Parameters version 1 0 18 intersAi 3 7 1 3 Modify the Ethernet Interface Configuration N ewtec Air MAC address 00 06 39 00 43 57 SHAPING THE FUTURE OF SATELLITE COMMUNICATIONS l aq Expert Log out 6 EI satellite Software Reboot om Configuration for Ethernet Interface Status Configuration Ethernet Interface Satellite Interface Multicast Eth MAC Address 00 06 39 00 A3 58 Device Management IP Address 192 168 1 1 Software Hardware Netmask Antenna Pointing Back Save Test Figure 15 Web Interface gt Edit Configuration Ethernet Interface gt Click on Edit in the Web Interface gt View Configuration Ethernet interface Figure 15 to change the Ethernet Settings gt Edit the parameters to be changed gt Click on Save in the Web Interface gt Edit Configuration Ethernet interface Figure 15 to save the new settings The Ethernet interface configuration is now saved 3 7 2 Satellite Interface These settings may only be changed upon advice of your internet YN service provider
37. n detail in the Point amp Play Setup Manual of your IPmodem Please read this Point amp Play Setup Manual carefully during installation gt gt v V V WV Y Vv V V WV version 1 0 Prepare the installation site and unpack the devices Select a suitable location to set up the antenna Lookup the exact satellite position in the Antenna Pointing Information booklet and use a compass if necessary The distance between the antenna and the IPmodem may not exceed 30 metres Ideally this distance shall not exceed 30 metres if making use of the cable provided with the Sat3Play Terminal set up the antenna pole and attach the masthead to it Attach the antenna to the masthead Attach the iLNB to the antenna Place the IPmodem in a clean dry room at maximum 30 m cable length from the antenna site Connect the Pmodem to the iLNB using the Rx and Tx coax cables Connect a computer desktop or laptop to the IPmodem Power the IPmodem Use a web browser on the computer to access the Terminal Web Interface Point the antenna towards the correct satellite fine tune pointing and verify the cross polarisation Configure the terminal using the web interface and or check the connectivity 3 interSA 2 GETTING TO KNOW YOUR SAT3PLAY TERMINAL 2 1 The IPmodem 2 1 1 The IPmodem Front Panel ae a RX TX a 1 2 3 4 5 Figure 2 The I Pmodem Front Panel 1 Power LED Green continuous when p
38. nnnnnn 25 Io DOVO ERE EE EE EE EN EN EE 27 3 8 1 SJ LIE JE EEE EE EE EEE 27 3 8 1 1 Introduction General Case rrrnnnnnnnnnnnnrnnnnnnnnnrnnnnnrnnnrnnnnnrnnnrnnnnnennnnnnenee 27 3 8 1 2 Software Upgrade rrrnnnnnnnnrrnnnnnvvrrnnnnnrrnnrnnnnnrnnnrnnnnnrnnnnnnnnnsnnnnnnnnsennnnnnsnee 28 see TINO WANG EEE 30 NNN ke 31 3 10 EEE 32 3 10 1 On Screen Test Results cc ccccccceescceseeeeesccsseeeessccsseeeessccseeeeesscseeeees 33 3 10 2 Filed Test BRENN 34 3103 Test IDSSCHIDUONS iwiscatacauudestesieeeinasnsvactas da cacti caulsdedesiecnoraassuactuvicecnswunebedesnede 34 3 10 3 1 Software Test mmrrrrrnnnnrrorrvrrrrnnnnnnnnrrrrnrrrnnnnnnrrrrnnrrnnnnnnnnssnnnnnnnnnnsnnnsennnn 34 3 10 32 Ethernet LAN 16S losceiatcinanttistincn2adpteninandsaenDeaneensaiutiuda a an R ieaiaia 35 3 10 3 3 Satellite Connection Test rrrrrrrrnnnnrvrrrnnnnnrvvrrnnnnnrnnrrnnnnrrennrnnnnnrrnnnnnsnee 35 version 1 0 3 10 3 4 Traffic Test rrnrrerrevnnnnnrvrevnnnnrrvrevnnnnnevrennnnnnsnnennnnnnrnnnnnnnnsrnnnnnnnnuenennnnnnee 35 4 Appendix A Troubleshooting Guide rrrnnnnnnnnnnnvnnnnnnnnnnnnnnnennnnnnnnnnnnnenenr 36 5 Appendix B ACTON YING Ls aaa 39 6 Appendix C Licenses snisciiecnnctinicencecesicantetesdenineivasnedieneenteaxnentecsexenmeecneucsauens 41 version 1 0 su intersAi 1 INTRODUCTION 1 1 Contents This manual describes the features and the terminal web interface of the IP modem 1 2 Manuals The Sat3Pl
39. or is still occurring after a number of hours contact your ISP to report the problem to check if your IPmodem is provisioned in the network version 1 0 i interSA Error Problem indication Possible solution Code version 1 0 37 Error information in the web interface Network lookup failed LED error indication Warning LED is on RX LED is on Error information in the web interface Synchronisation process failed LED error indication Warning LED is on RX LED is on Error information in the web interface Synchronisation lost LED error indication Warning LED is on RX LED is on Error information in the web interface Network login failed Error information on the IPmodem LED error indication Warning LED is on RX LED is on Error information in the web interface Network Layer configuration failed LED error indication Warning LED is on RX LED is on Error information in the web interface TCP acceleration service failed LED error indication Warning LED is on RX LED is on If the IP modem could not login to the satellite network maybe the result of pointing to a wrong satellite Verify the configuration of the satellite interface If the pointing data is correct check if the antenna is pointed correctly Re point if necessary Reset the IP modem Contact the ISP Internet Service Provider if this error is persistent for more than four hours The time synchronis
40. owered up 2 Warning LED Yellow continuous when the terminal is not logged on to the satellite network LAN indicator LEDs Left Green continuous link layer status Right Green blinking Ethernet frames are received or transmitted 4 Rx indicator LED Green continuous forward satellite signalling receiving 5 Tx indicator LED Green blinking traffic transmitting via the satellite link Table 1 Description of the Elements on the IPmodem Front Panel version 1 0 intersAi 2 1 2 The IPmodem Back Panel Figure 3 The IPmodem Back Panel Ne What Description O Indoor connection for the transmit coax cable Indoor connection for the receive coax cable 3 Reset button Reboot press once briefly hold less than 5 seconds Factory Reset press and hold for more than 5 seconds Resetting will also reboot the terminal and change all the IP settings back to the default factory settings 4 15V power cable Power connector 5 5 2 5mm plug connector 5 Ethernet cable connector Connection for the LAN type RJ 45 Ethernet cable Table 2 Description of the Elements on the I Pmodem Back Panel version 1 0 Biter 2 2 TheiLNB The iLNB has an integrated casing and is fully sealed except for its ventilation slots Figure 4 iLNB gt Perspective and Bottom View Nr what Deseripton 1 Feed horn Radiating feed horn of the iLNB pointed towards reflector 2
41. te Interface Multicast Device Software Antenna Pointing Test Figure 27 Web Interface gt Hardware version 1 0 55 00 06 39 00 B62 2A Reboot 20 interSA _ Below are given the displayed parameters and their description These values are read only Table 15 Configuration Page gt View Hardware Parameters 3 9 Antenna Pointing N ewtec AE ee SHAPING THE FUTURE OF SATELLITE COMMUNICATIONS pe Expert Log out Ethernet Q Satellite Q Software Reboot C status Status Configuration i Overview Ethernet Interface Satellite Interface Modem State synchronised se QO Demodulator 53 3 dBm E_ N 17 1 dB Device Software Version 1 7 10 0 Software Hardware Pointing Your antenna is pointed Click the Restart Pointing button to restart the pointing procedure Do not start pointing without pointing documentation Restart Pointing Figure 28 Antenna Pointing Restart Pointing In case the antenna should be re pointed click the button The pointing procedure is described in the Point amp Play Setup Manual The GUI interface is described in paragraph 3 6 2 5 version 1 0 3 intersAi 3 10 Test To view the functioning status of the Sat3Play Terminal or to identify problems that may occur tests can be run on the terminal Tests started 170736 seconds ago Software test Software test Ethern
42. y Alternate Version Alternate Software Only displayed when an alternative software version is Version present Table 14 Software Page 3 8 1 2 Software Upgrade A newly installed software version must pass an automatic software validation procedure When this software validation process fails the old software version remains in use The passive bank now contains a newer software version that did not pass the validation process In this case the user has the possibility to re trigger the validation process This situation can occur when a user turns off his IPmodem during the validation process or when satellite connectivity was not possible to establish during the validation process It is possible that the terminal performs a software update during the first logon This process can take up to ten minutes You may NOT interrupt the terminal yourself during this period by e g rebooting or powering down interSA Newtec duress 60 26 74 28 76 63 SHAPING THE FUTURE OF SATELLITE COMMUNICATIONS Mg u9ed in from Hub Fthernet Satellite Software Reboot Status EE m rn mm vn Software Download Identifiers Software Download Manufacturer ID 000639 Software Download Hardware ID 0x0001 Configuration Ethernet Interface Satellite Interface Multicast Device sesso Software Version Hardv re Currently Running Software Version 1 9 8 9 Antenna Pointing Alternate Software version 1 9 8 0 Try A
Download Pdf Manuals
Related Search