User manual - Lazer Helmets
Contents
1. MUSIC VOLUME DOWN or viceversa 10 BATTERY CHARGING Lazer Blue works with a Li Pol battery which allows for a typical talk time of 8 to 12 hours depending on the functions in use intercom Bluetooth connection 8 hours Bluetooth connection only 12 hours When the battery is close to flat the unit sends a warning message LOW BATTERY which is repeated 3 times Connect the plug of the supplied battery charger F into a main socket and the mini USB connector to the filter G connect the filter to the connector B situated below right of your helmet full cycle of recharge lasts approximately 6 hours if the battery is totally flat While charging the small LED flashes slowly in green If the battery is totally flat it may take a while before the LED starts to flash When the recharge is complete the LED turns off Recommendations EE Do not recharge Lazer Blue with any other battery charger than the supplied one Do not operate the multifunction key A during the recharge Do not charge your Lazer Blue without having first connected the filtre G between the battery charger F and the charger connector B to your helmet 27 LAZER LAZER BLUE LAZER Y 11 LED INDICATIONS TABLE OF CONTENTS gt Unit off The LED is off Unit on The LED flashes slowly in green Unit in pairing mode The LED flashes in green and red Unit in charge mode The LED flashes in2. to each other The units need to be named see section 5 4 and to be within range The procedure below has to be carried out simultaneously on both PROCEDURE VOICE INSTRUCTION FLOW Start condition Lazer Blue off control units close to each other LAZER BLUE 1 Press and hold down the multifunction key A until you hear PAIRING MODE then release 2 As the unit senses the presence of another unit in pairing mode it will prompt you to CONFIRM GROUP PAIRING Press shortly to confirm 3 Pairing takes place automatically If it is successful you will hear PAIRED WITH xxxxxx name of mate PAIRED WITH the name of the mate unit unify 4 If no further action follows the unit quits the pairing mode about ten minutes later LAZER BLUE ON LAZER BLUE ON 5 The units are now in intercom communication and will connect to each other whenever they are within range LAZER BLUE TABLE OF CONTENTS gt English 6 2 Bike to bike intercom communication To enable communication all the units max 6 have to be paired i e introduced to one another The units need to be named see section 5 4 and to be within range The procedure below has to be carried out simultaneously on all Lazer Blue units PROCEDURE VOICE INSTRUCTION FLOW Start condition Lazer Blue off control units close to one another LAZER BLUE ON 1 Press and hold down the multifunction key A until you hear PAIR
3. 2 As you hear MAKE PHONE CALL press shortly to confirm 9 3 Connecting Lazer Blue with a satellite navigation system The connection of a paired satellite navigation system may be automatic as soon as it is turned on and within range about 10 m or it may require action on Lazer Blue or on the navigator itself To initiate connection from the navigator refer to the operation guidelines that come with it To initiate connection from Lazer Blue see the procedure described below 23 LAZER LAZER BLUE TABLE OF CONTENTS gt English PROCEDURE VOICE INSTRUCTION FLOW Start condition Lazer Blue on navigation system on and within MENU range 1 Press and hold down the multifunction key A until you hear CONNECT PHONE MENU then release and listen to the prompts 2 As you hear CONNECT PHONE press shortly to confirm Connection is established and the indications from the navigator will reach you through the earphones of Lazer Blue 9 4 Connecting Lazer Blue with a music player The connection of a paired music player may be automatic as soon as it is turned on and within range about 10 m or it may require action on Lazer Blue or on the music player itself To initiate connection from the player refer to the operation guidelines that come with it To initiate connection from Lazer Blue see the procedure described below PROCEDURE VOICE INSTRUCTION FLOW Start condition Lazer Blue on music player on an
4. Optional handlebar remote control This accessory is designed to make the selection of functions more comfortable and safe while driving with the hands always gripping the handlebar firmly It is specially recommended for those who want to benefit from a maximum of functions and comforts It can be purchased separately to complement the rider s kit It consists of a three button selector to be fitted to the handlebar see picture and of a mini control unit The connection between the remote control and the Lazer Blue unit is radiofrequency type For detailed information about fitting pairing and operation see section 12 2 FITTING See the video on the Lazer website 3 OVERVIEW OF FUNCTIONS Lazer Blue allows for multiple wireless connections Rider to passenger and bike to bike intercom connection among up to six units within a range of about 150 meters typical in full duplex mode i e the bikers can talk and listen simultaneously Bluetooth connection to mobile phones for handsfree conversation Bluetooth connection to music players e g MP3 players allows for the reception of hi fi stereo music Bikers can listen to their favourites in the earphones and possibly share them with their biking mates Bluetooth connection to satellite navigation systems the voice indications from navigators can be listened to in the earphones zb LAZER LAZER BLUE TABLE OF CONTENTS gt English All the set up and control operat
5. 8 Connection and use with other Lazer Blue units intercom communication 8 1 Rider to passenger intercom communication 8 2 Bike to bike intercom communication 8 3 Suspending intercom communication 8 4 Selective intercom communication 9 Connection and use with Bluetooth enabled devices 9 1 Connecting Lazer Blue with a mobile phone 9 2 Using Lazer Blue with a mobile phone 9 2 1 Incoming phone calls handsfree 9 2 2 Sharing phone calls 9 2 3 Redialling 9 3 Connecting Lazer Blue with a satellite navigation system 9 4 Connecting Lazer Blue with a music player 9 4 1 gt Controlling the music player 9 4 2 Sharing music 10 Battery charging 11 LED indications 12 Optional handlebar remote control 12 1 Installation of the handlebar remote control 12 2 Pairing of the handlebar remote control 12 3 Clearing a paired remote control 13 Reset 14 Technical Data 15 Homologation Qualification LAZER BLUE TABLE OF CONTENTS gt English 1 KIT COMPOSITION The single kit includes the parts that are required by one biker that is 1 pair of earphones with foam pads D 1 microphone for jet flip up E helmet E 1 main connector 9 1 battery charger 1 filtre A 1 multifunction key B 1 charger connector For bike to bike rider to passenger intercom use each helmet will require one kit LAZER BLUE TABLE OF CONTENTS gt English 1 1
6. BUTTON TO RECORD NAME press shortly and say your name clearly close to the microphone If the operation UNIT NAME is successful you will hear it repeated in the earphones LAZER BLUE TABLE OF CONTENTS gt English 5 The unit sets itself to pairing mode If you have made a mistake you can repeat the procedure starting from pos 2 If no further PRESS BUTTON TO RECORD NAME action follows the unit quits the pairing mode about ten minutes later bexxxxxxx repetition of recorded name Remarks unit name can be modified at any time following the same procedure it can also be listened to by accessing the procedure and pressing shortly as you hear PLAY UNIT NAME f you have done group pairing see section 6 consider that the name change will exclude you from the group communication To quit the pairing mode before ten minutes have elapsed press and hold down until you re enter the MENU Wait until you hear and press the button shortly to confirm Tips gt Press shortly to confirm a command Do not keep pressed Press while hearing the voice prompt immediately after If you wait too long the system steps on and the selection becomes impossible 10 LAZER LAZER BLUES 4 TABLE OF CONTENTS gt English 6 PAIRING WITH OTHER LAZER BLUE UNITS 6 1 Rider to passenger intercom communication To enable communication the two units have to be paired i e introduced
7. CHANGE UNIT NAME LIST INTERCOMS GROUP PAIRING DELETE REMOTE CONTROLS DELETE BLUETOOTH UNITS OPERATION COMPLETED LAZER BLUE TABLE OF CONTENTS gt English 8 CONNECTION AND USE WITH OTHER LAZER BLUE UNITS INTERCOM COMMUNICATION 8 1 Rider to passenger intercom communication The full duplex connection of two paired units is automatic as soon as they are turned on and within range about 150 m If the range is exceeded communication is cut It is reinstated automatically as soon as the units are within range again When used as a rider to passenger intercom only two units being paired Lazer Blue allows you to share phone conversation and music listening see sections 9 2 2 and 9 4 2 8 2 Bike to bike intercom communication The full duplex connection of multiple paired units is automatic as soon as they are turned on and within range about 150 m If the range is exceeded communication is cut It is reinstated automatically as soon as the units are within range again 8 3 Suspending intercom communication Intercom communication can be suspended reinstated at any time following the procedure below If you are in a group the other members will continue to be in communication with one another PROCEDURE VOICE INSTRUCTION FLOW Start condition Lazer Blue in intercom communication 1 Press and hold down th
8. Lazer Blue allows you to share phone conversations with your riding mate To pre set this function operate as described below PROCEDURE VOICE INSTRUCTION FLOW Start condition Lazer Blue on MENU 1 Press and hold down the multifunction key A until you hear MENU then release and listen to the prompts MAKE PHONE 2 As you hear CONFERENCE CALL ON press shortly to confirm or 3 To switch off this function follow the same procedure and press PHONE shortly as you hear CONFERENCE CALL OFF MUSIC PLAYER INTERCOM CONFERENCE CALL ON or viceversa CONFERENCE CALL OFF 20 LAZER LAZER BLUE TABLE OF CONTENTS gt English This setting is also possible during a phone call with a quicker procedure PROCEDURE VOICE INSTRUCTION FLOW Start condition Lazer Blue on the connected phone in use MENU 1 Press and hold down the multifunction key A until you hear MENU then release CONFERENCE CALL ON 2 As you hear CONFERENCE CALL ON or CONFERENCE CALL OFF or viceversa press shortly to confirm CONFERENCE CALL OFF 9 2 3 Redialling This procedure allows you to call the latest number you have dialled this function is not available with all mobile phones PROCEDURE VOICE INSTRUCTION FLOW Start condition Lazer Blue on and connected with a mobile phone MENU 1 Press and hold down the multifunction key A until you hear MENU then release MAKE PHONE CALL
9. indications MUSIC VOLUME 1 2 3 25 LAZER tee 4 TABLE OF CONTENTS It should be kept low if you are simultaneously in intercom connection 9 4 2 Sharing music English MUSIC VOLUME UP MUSIC VOLUME DOWN When used as a rider to passenger intercom only two units being paired Lazer Blue allows you to share the listening of music with your riding mate PROCEDURE Start condition Lazer Blue on music player connected 1 Press and hold down the multifunction key A until you hear MENU then release and listen to the prompts 2 you hear MUSIC PLAYER press shortly to confirm 3 The system enters a submenu prompting all the controls that are typically available on music players As you hear SHARE MUSIC ON press shortly to confirm 4 disable this function follow the same procedure and press as you hear SHARE MUSIC OFF Please note Lazer Blue is designed to stream hifi stereo music from Bluetooth enabled music players However audio quality will be inferior in the second headset as it will be transferred through the intercom channel which does not support hi fi stereo transmission 26 VOICE INSTRUCTION FLOW MENU v PHONE or ICONNECT PHONE v ISTOP v PLAY v PAUSE v NEXT TRACK v PREVIOUS TRACK LAZER BLUE TABLE OF CONTENTS gt English MUSIC VOLUME UP
10. instrument board Secure the cable with tie wraps The mini control unit shall also be secured to the original wiring harness with tie wraps far from metal surfaces that may screen and compromise radio communication with the main control unit The two power supply wires shall be connected as described below RED wire to an ignition controlled positive supply wire 15 54 BLACK wire to a permanent negative supply e g a screw on the frame Solder the wire connections and insulate them carefully with tape 29 LAZER 4 TABLE OF CONTENTS 12 2 Pairing of the handlebar remote control The handlebar remote control needs to be paired with the Lazer Blue unit PROCEDURE Start condition Lazer Blue off remote control within range No other Lazer Blue unit or Bluetooth enabled device in pairing mode 1 Press and hold down the multifunction key until you hear PAIRING MODE then release 2 Press the central button of the selector and hold it down At the same time turn the motorcycle ignition on The red and green LED s on the selector will flash for a few seconds then the green LED will turn to solid light 3 the pairing succeeds you will hear PAIRED WITH REMOTE then LAZER BLUE ON 4 f the pairing fails you will hear FAILED PAIRING and subsequently LAZER BLUE ON 5 Once paired Lazer Blue and the remote control will connect to each other whenever the ignition is turned on and the units are within r
11. navigator with different procedures for each model Consult the operation manual of the navigator for information relating to the pairing of Bluetooth devices The navigator will list the Lazer Blue as an available device Select this item When you are prompted to enter a pin code digit 0000 four zeros If the pairing fails you will hear FAILED PAIRING and subsequently LAZER BLUE ON If it succeeds you will hear LAZER BLUE ON VOICE INSTRUCTION FLOW LAZER BLUE ON PAIRING MODE LAZER BLUE ON If unsuccessful FAILED PAIRING LAZER BLUE ON ter BLEN 4 TABLE OF CONTENTS 4 Once paired Lazer Blue and the navigation system will connect to each other whenever they are within range Connection may be automatic or require action on either device see section 9 7 3 Pairing with music players English If you wish to listen to music from a Bluetooth enabled music player e g a MP3 player through Lazer Blue s earphones you need to first pair your unit to the device PROCEDURE Start condition Lazer Blue off music player in pairing mode consult the operation manual of the music player close to the Lazer Blue unit No other Lazer Blue unit or Bluetooth enabled device in pairing mode 1 2 Press and hold down the multifunction key A until you hear PAIRING MODE then release From this step on pairing is managed by the music player with diff
12. whieh thia declaration relates are in conformity with the essential requirements and other relevant provisions of Directive 99 5 EC RATTE Directive Reference standards Safety EN 60050 1 2005 2 edition and EN 60050 1 2006 301 459 1 V1 8 1 2008 04 RF Spectrum 300 328 V1 7 1 2006 10 Tost Reports issued by RF Global Services Lid Vetere gri ned ei n y tg Basingstoke Hampshvre RGIS SOG United Kingdom Intended use in Al EU Countries Switzerland Norway and Prac and date of imum of DoC DAT Signed tor the manufacturer La Nama A Palumbo Titia Product Manager Motorcycle 33 LAZER LAZER BLUE TABLE OF CONTENTS English Let s respect the environment and public health Under no circumstances shall this electronic device be disposed of as part of ordinary household waste At the end of its life take it to an appropriate collection site as arranged by your local administration or by a retail store in your area Conditions of guarantee This product is guaranteed for 24 months from the date of purchase certified by a receipt or an invoice The warranty will become null and void if the failure appears to be caused by inadequate fitting misuse by fall or transportation by neglect or anything else than a manufacturing fault Moreover it will not apply if the unit is opened by personnell not authorised by COBRA AT In the event of incorrect fitting misuse the manufactu
13. ING MODE then release 2 the unit senses the presence of other units it will prompt you to CONFIRM GROUP PAIRING Press shortly to confirm 3 Pairing takes place automatically If it is successful you will hear PAIRED WITH the names of all the mate units PAIRED WITH xxxxxx name of mate 4 If no further action follows the unit quits the pairing mode about ten minutes later LAZER BLUE ON 5 The units are now in intercom communication and will connect to one another whenever they are within range unit PAIRED WITH xxxxxx name of mat PAIRED WITH xxxxxx name of mat unit LAZER BLUE ON Remark EN Every new pairing with other Lazer Blue units for rider to passenger or bike to bike communication supersedes the former pairing In other words whenever you go through the procedure to pair with new mate units the formerly created communication group is deleted and a new one is created LAZER BLUE TABLE OF CONTENTS gt English 6 3 Listing the paired Lazer Blue units Whenever you wish you can obtain a list of the units that are paired with your Lazer Blue PROCEDURE VOICE INSTRUCTION FLOW Start condition Lazer Blue off LAZER BLUE ON 1 Press and hold down the multifunction key A until you hear PAIRING MODE then release 2 Press again and hold down until you hear MENU then release and listen to the prompts MENU 3 you hear LIS
14. LAZER BLUE LAZER 3 WIRELESS MULTIMEDIA COMMUNICATION SYSTEM Installation amp operation manual LAZER HELM S PROTECT YOUR FREEDOM Dear Customer Thank you for choosing Lazer Blue We recommend that you read the following pages carefully so that you get full satisfaction from it We recommend also that you register the purchase at www hello biker com so that we can keep you informed of news and software updates LAZER BLUE LAZER Y TABLE OF CONTENTS gt TABLE OF CONTENTS English Section 1 Kit composition 1 1 Optional handle bar remote control 2 Fitting 3 Overview of functions 4 Switching on switching off 4 1 Switching on 4 2 Switching off 5 The first things to do with your new Lazer Blue 5 1 Charge the battery 5 2 Choose a language 5 3 Adjust the volume 5 4 Name your unit 6 Pairing with other Lazer Blue units 6 1 Rider to passenger intercom communication 6 2 Bike to bike intercom communication 6 3 Listing the paired Lazer Blue units 7 Pairing with Bluetooth enabled devices 7 1 Pairing with mobile phones 7 2 Pairing with satellite navigation systems 7 3 Pairing with music players 7 4 Clearing paired Bluetooth enabled devices LAZER BLUE LAZER Y 4 TABLE OF CONTENTS gt English
15. T INTERCOMS press shortly to confirm The unit will list the names of all the paired Lazer Blue units PLAY UNIT NAME 4 If no further action follows the unit quits the pairing mode about ten minutes later CHANGE UNIT NAME LIST INTERCOMS Name of mate unit Name of mate unit Name of mate unit LAZER BLUE TABLE OF CONTENTS gt English 7 PAIRING WITH BLUETOOTH ENABLED DEVICES Your Lazer Blue can be paired with up to 5 different devices supporting the Bluetooth communication protocols HFP HandsFree Profile HSP HeadSet Profile A2DP Advanced Audio Distribution Profile and AVRCP Audio Video Remote Control Profile 7 1 Pairing with mobile phones To enable phone conversation through Lazer Blue s headset the unit needs to be first paired to your mobile phone Exception if you wish to connect to a mobile phone and a satellite navigation system at the same time skip this section Pair the unit to the navigation system see section 7 2 and the navigation system to the mobile phone refer to the operation guidelines of both devices PROCEDURE VOICE INSTRUCTION FLOW Start condition Lazer Blue off mobile phone in pairing mode LAZER BLUE ON consult the operation manual of the phone close to the Lazer Blue v unit No other Lazer Blue unit or Bluetooth enabled device in pairing mode LAZER BLUE ON 1 Press and hold down the multifuncti
16. T OPERATIONS TO DO WITH YOUR NEW LAZER BLUE 5 1 Charge the battery Recharge for at least 6 hours before use see section 10 5 2 Choose a language The voice instructions of Lazer Blue are available in several different languages Visit www hello biker com to find your preferred language and the download procedure LAZER BLUE TABLE OF CONTENTS gt English 5 3 Adjust the volume The sound volume can be adjusted to three levels PROCEDURE VOICE INSTRUCTION FLOW Start condition Lazer Blue on VOLUME 3 1 Press the multifunction button A shortly The system tells you what sound level it is currently adjusted to e g VOLUME 3 VOLUME 2 2 Press shortly again The system shifts to the next higher or lower level VOLUME 1 WARNING EXCESSIVE SOUND PRESSURE FROM EARPHONES CAN CAUSE HEARING LOSS 5 4 Name your unit Choose a name that will allow your biking mates to identify you the default name is Lazer Blue PROCEDURE VOICE INSTRUCTION FLOW Start condition Lazer off far from other active LAZER BLUE ON Bluetooth enabled devices or Lazer Blue units in pairing mode 1 Press and hold down the multifunction key A until you hear PAIRING MODE then release 2 Press again and hold down until you hear MENU then release and listen the prompts 3 you hear CHANGE UNIT NAME press shortly to confirm PLAY UNIT NAME 4 As you hear PRESS
17. X your name 15 CALLING and needs to confirm by shortly pressing the 19 VOICE INSTRUCTION FLOW MENU MAKE PHONE CALL or CONNECT PHONE MUSIC PLAYER INTERCOM OFF ter BLUEN 4 TABLE OF CONTENTS multifunction key of his her unit within 5 seconds If this does not happen the message is repeated twice 7 When you wish to reinstate connection with all the group members follow the same procedure and press shortly as you hear the instruction CLOSE CALL 9 CONNECTION AND USE WITH BLUETOOTH ENABLED DEVICES 9 1 Connecting Lazer Blue with a mobile phone English Name of mate unit name of mate unit or viceversa The connection of a paired mobile phone may be automatic as soon as it is turned on and within range about 10 m or it may require action on Lazer Blue or on the phone itself To initiate connection from the phone refer to the operation guidelines that come with it To initiate connection from Lazer Blue see the procedure described below PROCEDURE Start condition Lazer Blue on mobile phone on and within range 1 Press and hold down the multifunction key A until you hear MENU then release and listen to the prompts 2 As you hear CONNECT PHONE press shortly to confirm 20 VOICE INSTRUCTION FLOW MENU LAZER BLUE TABLE OF CONTENTS gt English 9 2 Using Lazer Blue with a mobile phone E NE R
18. ange 30 English VOICE INSTRUCTION FLOW LAZER BLUE ON PAIRED WITH REMOTE LAZER BLUE ON If unsuccessful FAILED PAIRING LAZER BLUE ON LAZER BLUE LAZER Y TABLE OF CONTENTS gt 12 3 Clearing a paired remote control This procedure allows you to clear a paired remote control PROCEDURE 1 Start condition Lazer Blue off 2 Press and hold down the multifunction key until you hear PAIRING MODE then release 3 Press again and hold down until you hear MENU then release and listen to the prompts 4 you hear DELETE REMOTE CONTROLS press shortly to confirm 5 f no further action follows the unit quits the pairing mode about ten minutes later 13 RESET English VOICE INSTRUCTION FLOW LAZER BLUE ON PLAY UNIT NAME CHANGE UNIT NAME LIST INTERCOM GROUP PAG OPERATION COMPLETED If required the system can be reset by keeping the multifunction key on the control unit pressed for about 30 seconds 31 LAZER BLUES 4 TABLE OF CONTENTS gt English 14 TECHNICAL DATA Power supply Li Pol battery 600mAh 3 7V Bluetooth Technology Version 2 0 with EDR class Il range 10 m Supported profiles HF HS A2DP AVRCP Proprietary RF Technology 2 4 2 483GHz ISM band typical range 150 m Size of the control unit 68X58X20mms Weight of the helmet fitted com
19. d within range 1 Press and hold down the multifunction key A until you hear MENU then release and listen to the prompts MAKE PHONE 2 you hear MUSIC PLAYER press shortly to confirm or 3 you hear CONNECT MUSIC PLAYER press shortly to confirm CONNECT PHONE MUSIC PLAYER CONNECT MUSIC PLAYER 24 LAZER LAZER BLUE TABLE OF CONTENTS gt English Remark EN gt This procedure may apply also if you wish to listen to music from a mobile phone or a navigator supporting the A2DP profile 9 4 1 Controlling the music player The functions of the music player you have connected to Lazer Blue can be controlled via the multifunction key on the control unit PROCEDURE VOICE INSTRUCTION FLOW Start condition Lazer Blue on music player connected MENU 1 Press and hold down the multifunction key A until you hear MENU then release and listen to the prompts MAKE PHONE 2 As you hear MUSIC PLAYER press shortly to confirm or 3 The system enters a submenu prompting all the controls that CONNECT PHONE are typically available on music players Press shortly as you 3 come to the control you want select MUSIC PLAYER STOP PLAY PAUSE Please note 3 The music volume can be adjusted independently of the NEXT TRACK general volume setting to three different levels which are also PREVIOUS TRACK confirmed by voice
20. e multifunction key A until you hear MENU then release and listen to the prompts MAKE PHONE 2 you hear INTERCOM press shortly to confirm or 3 you hear INTERCOM OFF again press shortly to confirm CONNECT PHONE MUSIC PLAYER LAZER BLUE LAZER Y 4 TABLE OF CONTENTS gt Intercom communication is cut and can be re instated at any time following the same procedure and pressing shortly as you hear INTERCOM ON 8 4 Selective intercom communication English or viceversa While paired connected with multiple units you might wish to temporarily restrict communication to one member for instance you might wish talk with your passenger only while you are riding in a group This procedure allows to exclude the other members who will nevertheless continue to be in communication with one another PROCEDURE Start condition Lazer Blue in intercom communication at least with the unit you want to select 1 2 3 Press and hold down the multifunction key A until you hear MENU then release and listen to the prompts As you hear INTERCOM press shortly to confirm then listen to the prompts As you hear CALL UNIT press shortly to confirm Your unit will list the names of all the paired Lazer Blue units whether within range As you hear the name of the unit you wish to select press shortly to confirm The selected group member receives the message XXX
21. ecommendation To fully benefit from this function please take the time to first get acquainted with the features of your mobile phone Please note also that some models do not allow all the advanced functions to be transferred to Lazer Blue 9 2 1 Incoming phone calls handsfree Depending on the operating features and settings of the mobile phone when you receive a call you may hear the ring signal or the prompt PHONE CALL in the earphones Again depending on the operating features and settings of the mobile phone the phone communication may be opened automatically Automatic answer or you may need to press the multifunction key A on the Lazer Blue unit once to accept the call To reject the call you will need to press the multifunction key twice but this functionality is not available with all models of mobile phones To close a call you can either press the multifunction key twice or press and hold down the multifunction key until you hear MENU then release listen to the prompts and press shortly as you hear Phone calls take priority over other connections intercom connection connection to music players i e an incoming call interrupts the conversation with other bikers and or music listening Connection is reinstated when the phone call is closed 21 LAZER LAZER BLUE TABLE OF CONTENTS gt English 9 2 2 Sharing phone calls When used as a rider to passenger intercom only two units being paired
22. erent procedures for each model Consult the operation manual of the music player to look for information relating to the pairing of Bluetooth devices The music player will list the Lazer Blue as an available device Select this item If you are prompted to enter a pin code digit 0000 four zeros If the pairing fails you will hear FAILED PAIRING and subsequently LAZER BLUE ON If it succeeds you will hear LAZER BLUE ON Once paired Lazer Blue and the music player will connect to each other whenever they are within range Connection may be automatic or require action on either device see section 9 16 VOICE INSTRUCTION FLOW LAZER BLUE ON PAIRING MODE LAZER BLUE ON If unsuccessful FAILED PAIRING LAZER BLUE ON LAZER BLUE TABLE OF CONTENTS gt English 7 4 Clearing all paired Bluetooth enabled devices This procedure allows you to clear all the Bluetooth enabled devices that are paired to your system at one time PROCEDURE VOICE INSTRUCTION FLOW Start condition Lazer Blue off LAZER BLUE ON 1 Press and hold down the multifunction key A until you hear PAIRING MODE then release PAIRING MODE 2 Press again and hold down until you hear MENU then release and listen to the prompts 3 you hear DELETE BLUETOOTH UNITS press shortly to confirm r 4 If no further action follows the unit quits the pairing mode about PLAY UNIT NAME ten minutes later
23. green Battery charge completed The LED is off 12 OPTIONAL HANDLEBAR REMOTE CONTROL English Once this accessory is fitted and paired you will be able to access the main menu and select the functions described above by operating the mid button on the selector instead of the multifunction key on the control unit Use the lower and upper buttons to move back or forward more quickly in the menu When you are out of the menu use them to increase or decrease the sound volume Remarks turn Lazer Blue on and off you still need to press the multifunction key A on the control unit these operations cannot be controlled via the remote control No need to turn the remote control on off motorcycle ignition is turned on off The green LED on the selector flashes when the Lazer Blue unit is off it is illuminated with solid light when the Lazer Blue is on 28 It switches automatically when the LAZER BLUE TABLE OF CONTENTS gt English 12 1 Installation the handlebar remote control Loosen the screw on the three button selector unscrew it completely if required and slide the selector onto the left handle as shown in the attached picture then the screw as appropriate to keep the assy in position Route the flat cable that links the selector with the mini control unit down towards the foot of the steering post together with the original wiring harness located under the
24. ions described in the following pages are made via the same multifunction key A located on the control unit following the voice indications provided through the earphones For better comprehension of the instruction flow the tables below list all the indications you will hear in every menu submenu whether they require action this format DISP not this format MNO Multifunction button MG Recommendations NEVER ALLOW CONVERSATION ON THE PHONE OR WITH YOUR BIKING MATES DRAW YOUR ATTENTION AWAY FROM DRIVING AND GENERATE HAZARDOUS RIDING CONDITIONS WHEN ADJUSTING THE SOUND VOLUME ALWAYS KEEP IN MIND THAT YOU SHALL STILL HEAR CLEARLY THE AUDIBLE WARNING SIGNALS COMING FROM OTHER VEHICLES ESPECIALLY FROM THOSE INVOLVED IN EMERGENCY SERVICES SUCH AS AMBULANCES POLICE CARS FIRE BRIGADE VEHICLES ETC THE USE OF TWO EARPHONES MAY BE ILLEGAL IN CERTAIN COUNTRIES PLEASE CHECK THE LOCAL REGULATIONS AND ACT ACCORDINGLY LAZER BLUE 4 TABLE OF CONTENTS gt English 4 SWITCHING ON SWITCHING OFF 4 1 Switching on PROCEDURE VOICE INSTRUCTION FLOW Start condition Lazer Blue off Press and hold down the multifunction key A until you hear LAZER BLUE ON then release 4 2 Switching off PROCEDURE VOICE INSTRUCTION FLOW Start condition Lazer Blue on MENU Press and hold down the multifunction key A until you hear LAZER BLUE OFF then release LAZER BLUE OFF 5 THE FIRS
25. on key A until you hear PAIRING MODE then release 2 From this step on pairing is managed by the mobile phone with If unsuccessful different procedures for each model Consult the operation manual of the phone to look for information relating to the FAILED PAIRING pairing of Bluetooth devices The phone will list the Lazer Blue available device Select this item When you are LAZER BLUE ON prompted to enter a pin code digit 0000 four zeros LAZER BLUE LAZER Y 3 TABLE OF CONTENTS gt If the pairing fails you will hear FAILED PAIRING and subsequently LAZER BLUE ON If it succeeds you will hear LAZER BLUE ON Once paired Lazer Blue and the phone will connect to each other whenever they are within range Connection may be automatic or require action on either device see section 9 7 2 Pairing with satellite navigation systems English If you wish to listen to navigation instructions from a Bluetooth enabled system through Lazer Blue s earphones you need first pair your unit to the device PROCEDURE Start condition Lazer Blue off navigation system in pairing mode consult the operation manual of the navigator close to the Lazer Blue unit No other Lazer Blue unit or Bluetooth enabled device in pairing mode 1 2 Press and hold down the multifunction key A until you hear PAIRING MODE then release From this step on pairing is managed by the
26. ponents 116g Typical talk time 8 to 12 hours depending on the functions in use 15 HOMOLOGATION QUALIFICATION C Lazer Blue complies with the requirements of the EU Directive 1999 5 EC RTTE Directive in terms of electromagnetic compatibility health and safety use of the radiofrequency spectrum Moreover since it works for extended periods of time close to the user s head Lazer Blue has been duly submitted to SAR Specific Absorption Rate testing This is an international standard today recommended although not mandatory for this type of equipment that measures the human body s absorption of energy radiated by electronic equipments The values that have been measured are extremely low by far below the admitted figures Bluetooth Additionally it has been tested and found to comply with the requirements for Bluetooth Qualification This certification is mandatory for those manufacturers who want to use the official Bluetooth logo and trademark it guarantees that a device meets the standards of Bluetooth wireless technology 32 LAZER LAZER BLUE LAZER 4 TABLE OF CONTENTS gt English H KER cobra M Declaration of conformity Wa COBRA AUTOMOTIVE TECHNOLOGIES SpA 41 21100 VARESE ITALY under our soie responsibility that the products 6720 20 Wireless Multimedia Communication System for motorcycle and scooter heimet 6780 Handebar remote control for HeloBiker 2 0 fo
27. rer will not be liable for any kind of direct or indirect damage to persons or things Claims under this warranty shall be made through an authorised retailer Diagrams descriptions and features are merely indicative The manufacturer reserves the right to modify them without notice COBRA AT will not be responsible for damage 1o people or things resulting from negligence of these instructions or improper use The Bluetooth word and mark are owned by the Bluetooth SIG Inc and any use of such marks by Cobra automotive Technologies SpA is under licence Other trademarks and tradenames are those of their respective owners COBRA AUTOMOTIVE TECHNOLOGIES SPA VIA ASTICO 41 21100 VARESE www cobra at com O6DE3068x 05 10
Download Pdf Manuals
Related Search