Home

User`s Manual - EXP Computer, Inc.

1. 10 Now a partition is created in the external hard disk you can write data to it and if you want one more partitions can be created in the same hard disk drive just repeat the above steps 28 CHANGE THE DRIVE LETTER ASSIGNED HDD To change the drive letter for the external hard disk under Windows 98SE or Me for example from drive D to drive follow the instructions below 1 Open Control Panel then System click on Device Manager tab double click on Disk Drives select the model of the external hard disk then click on Properties button 2 Click on Settings tab check the Removable box under Options then change the Start drive letter and the drive letter to the letter you wish to assign for the hard disk 3 Click OK the drive letter will be changed after restart computer ETTE 06480 Papen ws A Meer T GI HEU Caf
2. drid EEE Fires ice Pe raza 5 Windows will complete the installation and then detect the hard disk drive inside the external hard disk kit and get it to work After system read the content of the hard disk drive about few seconds you will find a new drive letter has been assigned for the drive in Computer 6 Ifthe hard disk drive inside the kit 1s a whole new disk drive that doesn t contain any partition you can t File Action view read write data from to it please refer to the Partition the A Disk drives External Hard Disk chapter to prepare your hard disk Lx 206480 i E ODL H E drive CES TOSHIBA MK2103MAV H cal Floppy JISE OF SCSI and 5 PCMCIA HARDDISK 06 WINXP Installed Device Drivers Location PCMCIA HARDDISK D6 WINXP Installed under SCSI and RAID Controllers The real name of the hard disk drive inside the Installed under Disk Drives the name list in the i figure may differ from your hard disk drive 15 SOFTWARE INSTALLATION FOR WINDOWS NT Note Make sure the Windows NT system is version 3 51 or higher Since Windows NT does not support Hot Insert Remove feature this external hard disk should be connected to computer prior to starting Windows NT Likewise do not remove this drive before you shut down the computer In Windows NT the I O and IRQ
3. and start up the Found New Hardware Wizard click Next on the first screen 4 On this screen select Search for a suitable E bra adl Hadas Deren Dirree driver for my device Recommended car dris m ARA prognan hac amable a hades dam Lo pera vath T Bee serbe click Next SEE Thai cad vel correa Bra en dr cha ome cos Te 5 Insert the device driver diskette into floppy drive only select Specify a location leave the other check boxes be empty don t select them and click Next When the wizard asks for the path type A WIN2O00 in Copy manufacturer s files from location click OK Locale Diver Fiksa ethene co x at maior In pesh lor dras n 6 Wait for few seconds Windows will find a driver from the floppy diskette make sure Tha vara irithad order fies pour daca the file that Windows found is A Win2000 PCMHDZ2K INF Click Next 7 Click Yes on the Digital Signature Not Found screen Trond harar IMP n E 8 After the necessary files are copied into y Completing The Found New your internal hard disk a screen will appear Pm Hardware Wizard as the figure click Finish PCMCIA HARDDISK DG Windes 2000 Wahine har nares char Pe pare ior Hur dece the hai vented 9 Windows will complete the installation and then detect the hard disk drive inside the ext
4. eal 4 Windows will find two driver files from ZEIT j Welches vol ligue dl Sesion 06 ACHSE 11 13 2107 Ensure driver file that Windows found is PCMHD INF Click Next Windows will install the driver from the diskette After the necessary files are copied into your internal hard disk a screen will appear as the figure shown on right click Finish fifi Mendes Wiza indice dera ha aach D CHEK iD Kafka hu irish wd irata i i indios rr nor lo real bs ber depen en da eur cutee Edd re equa Dkk Back 20 seteci a difereni dives oi click Hed H ho Windows will complete the installation and then detect the hard disk drive inside the external hard disk kit and get it to work After system read the content of the hard disk drive about few seconds you will find a new drive letter has been assigned for the drive in Computer If the external hard disk doesn t appear in Computer or doesn t work properly please go into Device Manager to check whether the devices are installed as the table and figure seruus Manager nados Profi Performance If the device driver already installed properly but the O tiec RE drive still not present in Computer it means the EROS hard disk drive inside the kit 15 a whole new disk GEN
5. must change it to the Basic To do this right click on the status area left area of Disk 1 and then click Revert to Basic Disk from the options Wait for few seconds the type of the hard disk drive will be changed to Basic type To create a new partition in the external hard disk right click on the right area of Disk 1 click on Create Partition the Create Partition Wizard appears click Next Select Primary partition click Next Specify the size that you want this partition to be click Next Assign a drive letter for this partition please use the default value and click Next Refer to the figure shown below select Format this partition with the following settings choose the File system and specify a name for the Volume label select Perform a Quick Format then click Next Create Partition Wizard E xl Format Partition You can customize the formatting of the partition Specify whether you want to format this partition C Do not format this partition Format this partition with the following settings Formatting File system bo use Far 3z Allocation unit size Defaut Volume label D Enable and folder compression lt Back Cancel 21 9 Click Finish now the formatting is proceed after process is done the Disk Management window is changed as below Make sure the status of the partition is Healthy
6. then the external power connections if you are using the external power are made as described in Hardware Installation Slowly insert the PC Card of interface cable into the PCMCIA socket of computer and press firmly until the connector is seated Please note that the PC Card is keyed to guide for proper insertion 3 Windows will find a new hardware Found Hew Hardware Wizard named PCMCIA and start Welcome to the Found New up the Found New Hardware Wizard J Thes wsd helos you install for On the first screen select Install the software automatically insert driver diskette into floppy drive and M pour hardware came with an installation ED ur Hoppe deck incest i move then click Next ahat do pou mant the vara lo do ve riata the pofl reae acd ondes aby ec onsec n rd Leck Meat lo connue 14 4 Wait for few seconds Windows will find device driver from diskette and install it automatically After the necessary files are copied into your internal hard disk a screen will appear as the figure shown on right click Finish Fora red Hare Fearcesare Minor Found Hew Hardware Wizard Visai Pd Ad aa Ses at Completing the Found New Hardware Wizard e POLE HAFICDUSK The grand hes finished retelling be sole bor e PCMCIA HARDO HSE lH Fan DAAA
7. ERE DISE TIPER drive that doesn t contain any partition Windows Iia ULL LE T Hoster IDE Console 5 PCHDALHARODISE ME won t assign a drive letter for the disk drive without E DEE cual do Seconda DE comoda dua Wal any partition Please refer to the Partition the External Hard Disk chapter to prepare your drive PCMCIA HARDDISK D6 Installed under Disk Controllers The real name of the hard disk drive inside the Installed under Disk Drives the name list in the figure may differ from your hard disk drive 10 SOFTWARE INSTALLATION FOR WINDOWS 2000 1 Boot up your computer into Windows making sure pe the device driver for PCMCIA Adapters has been installed and is available To check this right click My Computer click Properties then Hardware and then Device Manager to open Device Manager window Refer to the figure shown alongside to see if the PCMCIA Controller is installed without error 2 Ensure the PCMCIA interface cable and then the external power connections if you are using the external power are made as described in Hardware Installation Slowly insert the PC Card of interface cable into the PCMCIA socket of computer and press firmly until the connector is seated Please note that the PC Card is keyed to guide for proper insertion 3 Windows will find a new hardware named PCMCIA PnPIDE
8. EXTERNAL User s Manual FCC COMPLIANCE STATEMENTS This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the Distance between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CAUTION CHANGE OR MODIFICATIONS NOT EXPRESSLY APPROVED BY PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER AUTHORITY TO OPERATE THE EQUIPMENT TRADEMARKS PCMCIA are the trademarks of Personal Computer Memory Card International Association MS DOS Windows Windows 95 98 Me 2000 XP NT and MSCDEX are trademarks of Microsoft Corpor
9. PCMCIA 2 1 Type II or III socket Windows 95 98 Me 2000 or Windows XP The Hot Insert Remove function is reachable with these OS Windows NT or DOS Windows 3 1 These OS don t support Hot Insert Remove function PART NAMES AND FUNCTIONS Your external hard disk may differ slightly from the figures shown however the controls will operate as described below 1 LED Power on and Data access indicator LED 2 Interface Connector This interface connector connects to the PCMCIA interface cable 3 Power Source Switch PC Means this hard disk is powered by the PCMCIA socket of computer DC Means this hard disk is powered by an external power source Usually when the external hard disk get the power from the PCMCIA socket of computer and it should work properly But with some models of computer the supplied power from the PCMCIA socket is poor to drives the hard disk drive In this situation an external power is needed If you experience this problem please contact dealer for the external power 4 External Power Jack This jack connects to an external power source If the jack labeled as SV you must use a 5Volts AC adapter or PS 2 power source cable as external power source If the jack labeled as DC IN you must use a 12Volts AC adapter as the external power source HARDWARE INSTALLATION Note If you want to use an external power to powers the hard disk please use the AC adapter or PS 2 pow
10. TITION THE EXTERNAL HARD DISK Using FDISK Under Windows 98SE Me FDISK is a program to create one or more partitions of the hard disk after the partition was built and formatted data can be write to the hard disk To partition the external hard disk you must execute FDISK under the MS DOS mode under Windows 98SE Me please follow the steps L Boot up the computer into Windows 98SE Me system Plug the external hard disk to computer and make sure it is recognized Go into MS DOS mode by click on Start gt Programs MS DOS Prompt At the DOS prompt type FDISK and press Enter In the first screen of FDISK answer the question Do you want to enable large disk support Y ifyou want to create a partition larger than 2GB FAT32 N ifyou want to create a partition small than 2GB FAT16 The next screen is FDISK OPTIONS IMPORTANT you must type 5 on this screen to change the current fixed disk drive the default fixed drive set by FDISK is your internal hard disk if you don t change it to the external hard disk the data of your internal hard disk will be destroyed EOS Prop POISE se Ce E oS X Note If the option 5 doesn t appear on this screen means the external hard disk is not installed properly please check with the software installation 24 6 In the Change Current Fixed Disk Drive screen type the disk drive number that assigned to external hard disk usually the extern
11. USING HARD DISK WITH PCMCIA INTERFACE To Connect The PCMCIA Hard Disk To Your Computer Windows 95 98 Me 2000 and WindowsXP 1 Boot into the Windows system 2 Insert the plug of the PCMCIA interface cable into the Interface Connector of drive 3 Make sure the Power Source Switch is at the correct position PC get power from the PCMCIA socket of computer DC get power from the external power 4 If you are using the external power connect the external power to the External Power Jack at the rear panel of the drive And then attach the external power to the outlet 5 Slowly insert the PC Card of interface cable into the PCMCIA socket of computer and press firmly until the connector is seated Your external hard disk is now ready for use in few seconds Windows NT and DOS Windows 3 1 Power off the computer 2 Insert the plug of the PCMCIA interface cable into the Interface Connector of drive 3 Make sure the Power Source Switch is at the correct position PC get power from the PCMCIA socket of computer DC get power from the external power 4 If you are using the external power connect the external power to the External Power Jack at the rear panel of the drive And then attach the external power to the outlet 5 Slowly insert the PC Card of interface cable into the PCMCIA socket of computer and press firmly until the connector 1s seated 6 Power on computer the external hard disk will ready for use after b
12. al hard disk is the fixed disk drive number 2 BONS Promi POISE 7 Back to FDISK OPTIONS screen type 4 to display the content of the fixed disk drive check the content to make sure the current drive is the external hard disk 8 Now you can create type 7 or delete type 3 the partition of the external hard disk 9 After you finish FDISK re boot computer to activate these changes em Using Disk Management Under Windows 2000 XP Note The external hard disk can t works with Dynamic Disk type Do not upgrade the external hard disk to Dynamic Disk type always use it with Basic Disk type To partition the external hard disk under Windows 2000 or Windows XP please plug the external hard disk and make sure it 1s recognized then In Windows 2000 click Start gt Settings gt Control Panel gt Administrative Tools gt Computer Management to open Computer Management window In Windows XP click Start gt Control Panel gt Performance and Maintenance gt Administrative Tools gt Computer Management to open Computer Management window 2 Click on Disk Management on the left part of this window all connected disk drives will be listed in the right part Find out the largest number of Disk for example on the below picture Disk 1 15 the largest number and it is the external hard disk right side of the Disk 1 15 the status of the partitions of this disk drive
13. atically 7 Reboot your computer and the hard disk drive will be recognized automatically 18 Manual Installation You may also manually install the external hard disk device driver Note The filename of the DOS device driver is different with the different version of driver package it could be ARIHD EXE or NVIHD EXE However you can find this driver in the root folder of the diskette the filename will be present as xxxHD EXE The following example is assumed the filename is NVIHD EXE replace the filename if you get the different driver file Copy the file NVIHD EXE from the device driver diskette to a directory in your main hard disk e g CPCMHD 2 Add the following line to the BOTTOM of your CONFIG SYS file DEVICE drive path NVIHD EXE P 320 Where drive path specifies the directory containing NVIHD EXE P is used to set the I O ports and the valid numbers are 320 340 and 360 Note If your CONFIG SYS file is already loaded with PCMCIA software such as Cardsoft of SystemSoft or Cardtalk of Databook it is necessary to add the above line after the PCMCIA software Otherwise the PCMCIA interface card will not be initialized properly The CONFIG SYS file example LASTDRIVE Z DEVICE C DOS HIMEM SYS DEVICE C DOS EMM386 EXE NOEMS X D000 D3FF FILES 40 BUFFERS 20 Rem put PCMCIA software here DEVICE C PCMHD NVIHD EXE P 320 5 Reboot your computer to activate the external hard disk drive 19
14. ation A I of the third party brands and names are the property of their respective owners CONTENTS INTRODUCTION ee ee re re 1 So LEN T S c 1 PART NAMES AND PUNCTIONS vcard 2 HARDWARE INSTALLATION unitis nucis entr I n PIRE IS MUNI IE 4 SOFTWARE INSTALLATION FOR WINDOWS 95 98 6 SOFTWARE INSTALLATION FOR WINDOWS Me eere 9 SOFTWARE INSTALLATION FOR WINDOWS 2000 eee 11 SOFTWARE INSTALLATION FOR WINDOWS 14 SOFTWARE INSTALLATION FOR WINDOWS 16 SOFTWARE INSTALLATION FOR DOS WINDOWS 18 USING HARD DISK WITH PCMCIA INTERFACE 20 ADVANCED USAGE eicit tutum OREMUS MD UEM 23 PARTITION THE EXTERNAL HARD nennen 24 USING FDISK UNDER WINDOWS 98SE Me eee 24 USING DISK MANAGEMENT UNDER WINDOWS 2000 XP 26 CHANGE THE DRIVE LETTER ASSIGNED TO HDD ee 20 INTRODUCTION The PCMCIA hard disk is a portable compact hard disk drive that attached with the PCMCIA interface of computer The external hard disk provides a fast and easy way to add more storage space to your computer Plus the Plug amp Play feature gives you a great convenience on the road The external hard disk can be easily connected to computer for using and can even be disconnected and re connected while the computer is running SYSTEM REQUIREMENTS Notebook or desktop computer with
15. e inside the Installed under Disk Drives the name list in the figure may differ from your hard disk drive SOFTWARE INSTALLATION FOR WINDOWS 1 Boot up your computer into Windows making sure the device driver for PCMCIA Socket has been installed and is available To check this right click My Computer click Properties and then Device Manager to open the Device Manager window Refer to the figure shown alongside to see if PCMCIA Controller is installed without error tle Prada Deag Device Hanger Hosen Profiles Petorrence Vw devices by Viae dances by connecton POND socket My Tadi iiun 1225 Car ui Controles E 2 Ensure the PCMCIA interface cable and then external power connections if you are using external power are made as described in Hardware Installation Slowly insert the PC Card of interface cable into the PCMCIA socket of computer and press firmly until the connector is seated Please note that the PC Card is keyed to guide for proper insertion 3 first screen insert the device driver diskette into floppy drive select Automatic search for a better driver Recommended and then click Next the floppy diskette and list as the figure shown alongside Select PCMCIA HARDDISK D6 and then click OK Adi Heas Mirad PLHCIA PARADE re can aubergine arch Ex and rela
16. er source cable provided by manufacturer using an incorrect external power could result in permanent and unpredictable damage to the drive This external hard disk supports Hot Insert Remove function only under Windows 95 98 Me 2000 XP with the other operating systems please insert the PC Card of interface cable before power on computer and remove this card after power off computer Insert the plug of the PCMCIA interface cable into the Interface Connector of drive Press firmly until the interface connector is seated correctly Make sure the Power Source Switch is at the correct position PC get power from the PCMCIA socket of computer DC get power from the external power Note If you are using an external power to powers the external hard disk the sequence is change the Power Source Switch to DC position then connect the external power to the External Power Jack of the drive and attach the external power to the outlet You are now ready to install the device drivers please follow the related software installation guide to install the device driver Get power from PCMCIA socket Switch to PC position Get power from the external power Switch to DC position SOFTWARE INSTALLATION FOR WINDOWS 95 98 The following installation procedures are extracted from the Windows 98SE installation The installation for Windows 95 is almost same HUI DS SB r E qx 1 Boot up your computer into Windows makin
17. ernal hard disk kit and get it to work After system read the content of the hard disk drive about few seconds you will find a new drive letter has been assigned for the drive in Computer 10 If the hard disk drive inside the kit is a whole new disk drive that doesn t contain any Yee partition you can t read write data from to it tc eee TOSHIBA MEZ2I03MAV SCSI Disk Device E please refer to the Partition the External Hard Disk chapter to prepare your hard disk drive PCMCIA HARDDISK D6 Windows 2000 Installed under IDE ATA ATAPI Controllers The real name of the hard disk drive inside the Installed under Disk Drives the name list in the figure may differ from your hard disk drive 2195 SOFTWARE INSTALLATION FOR WINDOWS XP Boot up your computer into Windows making sure the device driver for PCMCIA Adapters Bere has been installed and is available To check this 4 i Device Manager right click Computer click Properties I 6 Ml PCMCIA adapters then Hardware and then Device Manager to POR Texas Instruments PCI 1225 CardBus Controller open the Device Manager window Refer to the figure shown alongside to see if the Controller is installed without error 2 Ensure the PCMCIA interface cable and
18. ernal power connections if you are using the external power are made as described in Hardware Installation Slowly insert the PC Card of interface cable into the PCMCIA socket of computer and press firmly until the connector is seated Please note that the PC Card is keyed to guide for proper insertion 8 Power on the computer after boot into Windows the external hard disk will be assigned a drive letter in My Computer the drive is ready for use 17 SOFTWARE INSTALLATION FOR DOS WINDOWS 3 1 Automatic Installation Follow the instructions below to proceed with automatic installation 1 Insert the device driver diskette into a floppy disk drive on your computer 2 Changethe working directory to the floppy drive containing the device driver diskette by typing then press ENTER 3 At the DOS prompt A type INSTALL followed by the ENTER key 4 Press ENTER or click OK button to continue The screen will display as the following 1 Directory to install driver Type the directory that you want the driverfiles Pirecters to install drierri are copied to and then press the TAB key to forward to the next field 2 Set I O port to The default setting is 320 32F 5 After completing the selection press TAB key to the Install button and press ENTER to continue 6 The rest of the installation should proceed automatically the CONFIG S YS file on your computer will be updated autom
19. g sure email Device Hanger Habas Profiles Petorrance the device driver for PCMCIA Socket has been 7 deacar by lps Vise dans by connection installed and is available To check this right click PLH DIA My Computer click Properties and then Device Tte Tees nrunsri 1225 Contes Manager to open the Device Manager window me Refer to the figure shown alongside to see if the PCMCIA Controller is installed without error EN 2 Ensure the PCMCIA interface cable and then the external power connections if you are using the external power are made as described in Hardware Installation Slowly insert the PC Card of interface cable into the PCMCIA socket of computer and press firmly until the connector is seated Please note that the PC Card is keyed to guide for proper insertion ad Has Lenders Mirad 3 If this is the very first time you are connecting the drive to computer the Add New Hardware Wizard dialog box appears as shown pe He tm 4 Click Next then select Search for the best driver for your device box and click Next 5 Select Floppy disk drives box and insert device driver diskette into floppy drive Click Next 6 Wait for few seconds Windows will find a driver from the floppy diskette select PCMCIA HARDDISK D6 and click Next 7 Ensure the driver file that Windows found i
20. oot into the operating system 20 To Disconnect The PCMCIA Hard Disk From Your Computer Windows 95 98 and Windows Me on WM nm 1 Click on the icon or on system tray and a dialog box appears beside this icon 2 Click Stop PCMCIA HARDDISK D6 in the dialog box 3 Wait for few seconds until the system prompts The PCMCIA HARDDISK D6 can now be safely removed from the system Click OK and then remove the PC Card of the cable from computer Windows 2000 1 Click on the icon gt on system tray and a dialog box appears beside this icon 2 Click Stop PCMCIA HARDDISK D6 Windows 2000 in the dialog box 3 Wait for few seconds until the system prompts The PCMCIA HARDDISK D6 Windows 2000 can now be safely removed from the system Click OK and then remove the PC Card of the cable from computer Windows Click on the icon 2 on system tray and a dialog box appears beside this icon 2 Click Safely remove PCMCIA HARDDISK D6 WINXP in the dialog box 3 Wait for few seconds until system prompts The PCMCIA HARDDISK D6 WINXP can now be safely removed from the system and then remove the PC Card of the cable from computer Windows NT and DOS Windows 3 1 Power off the computer 2 Remove the PC Card of the cable from computer ls ADVANCED USAGE B Partition the External Hard Disk W Change the Drive Letter Assigned to HDD lt 23 PAR
21. s PCMHD INF Click Next fifi Has 6 After necessary files are copied into your f HARDDISE internal hard disk a screen will appear as I figure click Finish y 9 Windows will complete the installation and then detect the hard disk drive inside the external hard disk kit and get it to work After system read the content of the hard disk drive about few seconds you will find a new drive letter has been assigned for the drive in Computer 10 If the external hard disk doesn t appear in Computer or doesn t work properly please go into Device Manager to check whether the devices are installed as the table and figure sereni Devine Manager Protas Pestorranos 11 If the device driver already installed properly but the nee i dece hard disk still not present in Computer it means the hard disk drive inside the kit is a whole new disk drive that doesn t contain any partition Windows Hester IDE Contes HARFDDISE 95 98 won t assign a drive letter for the disk drive xm Seconda IDE criti dual Mo without any partition Please refer to the Partition the ha Dum PR External Hard Disk chapter to prepare your hard mue Pit disk drive PCMCIA HARDDISK D6 Installed under Disk Controllers The real name of the hard disk driv
22. settings of PCMCIA IDE device cannot be changed Therefore if the setting of this hard disk conflicts with other device change the I O or IRQ of other device to avoid conflicts We recommend you install a Card Service program e g SystemSoft s Card Wizard for Windows NT This kind of program will help Windows NT to assign resource for PCMCIA device properly and reduce the conflict situation 1 Do not connect the external hard disk to computer just power on the computer and boot into Windows 2 Click on Start gt Settings gt Control Panel gt SCSI E Deacer Dress Adapter The SCSI Adapter dialog box appears lt ee ee 3 Click Drivers tab and then click Add button A Dk Carcel 4 Click Have Disk button to continue Windows NT will then prompt you to insert manufacturer s driver diskette Insert the device driver diskette into floppy drive Specify the directory as A WINNT or BAWINNT whichever contains the diskette and click OK 16 5 Select PCMCIA HARDDISK and then click iu OK IF yaaa an dk For a divar in Un Have SCS Adapier PONSA HARDDISK 6 Follow the on screen instruction to continue After the installation is complete Windows will prompt you to restart to activate the new device driver Restart and power off the computer 7 Ensure the PCMCIA interface cable and then the ext
23. you can create a new or delete an exist partition by right click on this area The next steps will describe how to create a new partition on this external hard disk O Computer Management yew me tam npe Type Fte System Status capa M System Took Fe Event System Infometion Performance Logs and Alerts Shared Folders Zh Device Hanager Local Lesrs and Grouse Aij Storage 3 Disk Management e Logical Drives HE UI Removable Storage Unsoed Primary Partition Partition B Logical Drive Note If the hard disk in the external hard disk kit is a whole new hard disk without any partition when the Disk Management is opened a Stop mark indicates this drive is an Unknown type of disk refer to the figure shown on right side In 26 this situation Windows system won t allow you to create partition with this drive In the meantime you can In Windows 2000 Windows will start up the Write Signature and Upgrade Disk Wizard immediately You can use this Wizard to initial the hard disk to the Basic Disk type and can then create partition in the drive In Windows XP you can right click on the Stop mark and then click Initialize disk to initial the hard disk to the Basic Disk type and can then create partition in the drive If the type of the hard disk drive is Dynamic you

User`s Manual - EXP Computer, Inc.

Contents

Download Pdf Manuals

Related Search

Related Contents