GPS Vehicle tracker (LDW
Contents
1. Example CSBJH80 0 After sending command successfully the tracker will return a message config OK The Warning Speed Is 80 Off Time Zone Setup Format 896 E or W time zone The value of state is E and w E means eastern time zone W means western time zone Example 896 E 8 After sending command successfully the tracker will return a message config OK Set Current time zone as E8 Note The default time zone is GMT 8 So you need recover it to GMT O first with command 896 w 8 Then you can set your time zone accordingly Open GPS Signal Note Center number can send this command to open GPS The tracker will begin to work with GPS signal There is still GPS signal even the tracker is shutdown Format 810 After sending command successfully the tracker will return a message config OK Note The default GPS signal state is open Close GPS Signal Note Note Center number can send this command to close GPS The GPS module will stop working and in this mode there will be less power consumption There is still no GPS signal even the tracker is shutdown Format 811 After sending command successfully the tracker will return a message config OK Pre stored numbers Setup Format 711 password phone number1 phone number2 phone number3 phone number4 Note phone no 4 is the voice monitor no and it cannot be the same one as center num2. External Alarm Switch For Emergency 2 2 RED LED power working status LED Status Continuously in bright state Meaning Working normally Continuously in dark state Low battery power off 2 3 Green LED GSM status indicator LED Statue Meaning flashing Weak GSM signal searching GSM signal Continuously in bright state GSM conversation Start GPRS Continuously in dark state GSM not located 2 4 Blue LED GPS status indicator LED Status Meaning Flashing Weak GPS signal Searching GPS signal Continuously in bright state GPS located Continuously in dark state GPS not located 2 5 Ignition detection indication Three blue red green LEDs are in cycling flashing 3 Interface introduction Tele cutott Patrol stectricity gt Power interface ACC interlace interface Power on off A SIM card siot Data interface sos MIC intertace SOS interlace GPS status LED GSM status LED Power working status LED 4 Method of installation 4 1 Preparation before installation 4 1 1 Open the packing box to check whether the type of device is correct and whether the accessories are included or else please contact your distributor 4 1 2Choose SIM card each device needs to insert a GSM SIM card Please refer to the distributor s suggestions to choose the SIM card
3. 4 1 3 About the battery switch You need to make sure the device battery is on before installation Pls refer to the following 1 Battery switch off 2 Battery switch on 2 4 1 4 Installing SIM card The SIM card slot is on the right side of device Open the SIM card silicon seal then insert the SIM card to the slot do not insert the SIM card backwards When the SIM card is ready you will hear a click Or else please insert again and then replace the silicon seal Note Power off before installing or removing the SIM card The SIM card used should be enabled for GPRS The SIM card used should be enabled for caller ID If there is a power on password or pin please cancel it Ensure the SIM card can send and receive SMS 4 2 Installation The device installation is covert Please refer installation to an auto electrical contractor NOTE 4 2 1 To prevent theft of the device it should be installed as covertly as possible Covertly installation is suggested 4 2 2 Avoid placing the device close to higher power electrical devices such as reversing radar anti theft device or other vehicle communication equipment 4 2 3The device should be fixed into position with cable ties or wide double side tape 4 2 4 The device has built in GSM antenna and GPA antenna During installation please make sure the receiving side face is up with no metal object above the device to interfere with GPS reception The following places a
4. GPS Vehicle tracker LDW TKV106 GPS GSM SMS GPRS User Manual 1 4 Version Please read this manual carefully before attempting installation and online activation Pictures are for indication and illustration purposes only 1 Accessories Please check the accessories before using Pictures are for indication and illustration purposes only 2 Features e GSM 850 900 1800 1900 Quad band e Wide for voltage input range 9 36V DC e GPS continuous positioning GPRS timing interval e Real time tracking history playback e Check location information via SMS and GPRS TCP e Tele cutoff petrol function e SOS alarm e ACC ignition detection and Vibration alarm e Low battery alert e Over speed alarm e Voice monitor function e GEO fence e Compatible with external connection through serial port 2 1 1 Technical Specifications GSM Module GSM850 900 1800 1900MHz GPS Chip SIRF IV Chip GPS Sensitivity 159dBm GPS Centual L1 1575 42MHz GPS Accuracy 5 25m GSM Accuracy 100 500m Speed Accuracy 0 1m s Time Accuracy Same as GPS Warm status 15 Cold status 385 Highest altitude 18000M Max speed 515 M S Acceleration of Gravity lt 4g 2 1 2 Others Temperature 20 65 C Humidity 5 95 Voltage 10V 25V Power 10V 25V Average Power lt 80MA LED Indicate the working condition and other conditions of GPS amp GSM
5. ame no login password Example 2 8024CHINAMOBILE CCDLEN QIUXIA 21 RXO000 APN is CCDLEN the login user name is QIUXIA 21 and login password is RXOOOO Note The default APN of this product is CMNET Server connection Setup Format 803 domain name or IP address port number This command is used to set GPRS center server address which could be fixed IP number After the setup is successful the module will send a reply with config ok the ip server is 59 188 20 67 8545 Example 803 59 188 20 67 8545 Setup via domain name Example 803 www gps288 com 8545 Regular Upload Interval Setup The defaulted factory upload time interval of this device is 10 seconds for getting the point and uploading one point location information The user could change such parameter according to actual demand Format 730 sampling interval The value of sampling interval from 10 seconds to 3600 seconds For example 730 30 Note The parameter 30 indicates getting and uploading one point location information every 30s Vehicle Defense Setup Note You need to open the vehicle defense first then you can use the vibration Alarm or you cannot use vibration Alarm 1 Open vehicle defense Format 911 After sending command successfully the tracker will return a message config OK The Auto Alert Is On 2 Close vehicle defense Format 910 After sending command successfully the tracker will return a message conf
6. ber or any other pre stored numbers Only this number can do voice monitor For example You want to set four stored numbers 711 000000 13567892314 13892341600 13625678900 13625678901 The new numbers will replace the old numbers and it will send confirmation to the sender if the password is right CONFG OK Note 13625678901 is the voice monitor no only this number can make voice monitor SOS button Emergency call button In case of emergency please press SOS button over 3 seconds center number will receive a call and SMS Note SMS will be sent only when the device is online on the tracking system Device Setup inquiry Format 902 password Example 902 000000 After sending command successfully the tracker will return a message Settings The Main User Is 13689645010 The Auto Alert Is Off Low Battery Alert Is On The Vibrate Warning Is On The Alert Call Is Off The Warning Speed is Off Remote Restart Format 90382 password Example 90382 000000 After sending command successfully the tracker will return a message Config OK The Machine Will Restart Restore facto ry settings Format HFSZ Example HFSZ After sending command successfully the tracker will return a message Config OK Device Has Been Reset To Factory Setting 7 SMS amp Platform Tracking SMS location inquiry There is no need for Center number to add the password to inquiry Other numbers need to add the password
7. gram J N H LJ 7 2A FUSE fo tase box ose Mij OOC RS232 oe RX Interface Storage battery Connectto SOS button at S Q ho Connect to microphone 5 Cautions of device wiring 5 1 Power ACC Tele cutoff petrol electricity control line 4pin 5 1 1 The standard voltage is 9V 36VDC Please use the power Line which provided by the manufacturer The red line is the positive The black line is the negative The negative should earth alone or link iron during installing Do not connect it to other ground wire 5 1 2 ACC line orange is connected to the ACC switch of the vehicle Please make sure to connect the ACC line The tracker will decide whether to enter ignition detection according to ACC status If do not connect to ACC line the device will enter ignition detection status If the vehicle vibrates when moving it will activate the vibration alarm If there is no need for the theft proof function connect the ACC line to the positive in parallel and keep high level 5 1 3 Tele cutoff petrol electricity control line yellow is connected to pin 86 of the Tele cutoff petrol electricity relay equal to the yellow line of the relay socket 5 2 USB cable 3 pin Firmware updating interface expanded function to reserve space 5 3 MIC line 3 pin Externally connect to microphone for voice monitor function 5 4 SOS line 2 pin Externally connect to SOS sw
8. ig OK The Auto Alert Is Off Vibration Alarm Setup Format HZDBJ sensitivity 1 15 alarm mode 0 1 H Sensitivity 1 is the most sensitive and of course 15 is the most insensitive Alarm mode 0 indicates vibration alarm is closed Alarm mode 1 indicates the device will alarm you through calls or SMS Note SMS will be sent only when the device is online on the tracking system For example If you set ZDBJ 1 1 the device will send you back Config OK The Vibrate Warning Is 1 1 That means that the tracker is in a most sensitive status and alarm by calls Cut oil supply by SMS Format DY password state The value of state is 0 and 1 1 is cut off oil 0 is restore oil Example DY 000000 1 For safety this command will be function when the speed less than 5KM h After sending command successfully the tracker will return a message config OK and cut oil supply of the vehicle Low Battery Alert Setup Format DDBJ state The value of state is 0 and 1 1 means open low battery alert 0 means close low battery alert Example DDBJ 1 After sending command successfully the tracker will return a message config OK Low Battery Alert Is On Over speed Alarm Setup Format CSBJ speed limit km h state The value of state is 0 and 1 1 means open over speed alarm 0 means close over speed alarm
9. ing results 6 Please use this equipment in the legal areas The consequences of any violation of the law will be undertaken by the users themselves
10. itch for SOS function 6 SMS command format Note All the setup below can be only made by Center number Super User Setup Set the new center number and new password by SMS through mobile phone If the setup is successful the module will send a reply with Config OK the Main User and Password Is Reset To 13689645010 center no 123456 new password Format CJML SN code new password 6 digits Center number SN code pls checking it with backside of produt Example CJML 886600000633 000000 13689645010 Note Center number must be a mobile phone number telephone number will not work Center Number Setup Set the center number by SMS through mobile phone If the setup is successful the sender will receive CONFIG OK The main user is 13286689393 from the tracker Format 710 former password new password 6 digits center number For example 471040000004000000413689645010tt Note All alarming information thereafter including SOS low power electronic fence etc will be sent to this number 000000 is the default password APN Access Point Name Setup Set APN by SMS through mobile phone If the setup is successful the sender will receive CONFIG OK from the tracker Format 802 GSM provider name APN Log user name Log password The default APN is CMNET if the APN doesn t have login user name and password it can be set 0 Example 1 802 Chinamobile CMNET HO O APN is CMNET no login user n
11. re suggested for installation shelter in the decorated board below the front windshield shelter around the front instrument panel non metallic material face in the decorated board below back windshield Notice If the windshield is pasted with metal thermal protective coating or heating coating It may affect the receiving signal In this case please change the installation place 4 3 Device outlet specification Keypod Keypod MIC MIC TX RX GND MOTOR ACC Yy YV J OONO Msn Line No Specification Color Instruction 1 2 Keypod Orange Orange Connect to SOS button 3 4 MIC MIC Black Red Connect to Microphone 5 TX Green Sending data TX backup 6 RX White Receiving data RX backup 7 GND Black Ground wire 8 MOTOR Yellow Connect to relay control line 9 ACC Orange Connect to ACC ignition 10 V Black thick Vehicle12V 24V negative storage battery 11 V Red thick Vehicle12V 24V positive storage battery Notes of the relay wiring The relay wiring of pump oil connectors of both ends are affine white line 85 and a fine yellow line 86 The fine white line 85 is connected to vehicle positive power 12V The fine yellow line is connected to the device relay control line Cut off the positive connection line of the pump then connect in series to the relay N C contact thick green line 87a and the other end relay COM contact thick green line 30 4 4 Device wiring dia
12. to inquiry 1 Address tracking Format 666 password For example you send 46664000000tt to the tracker you will get a reply SMS as follow SN 886600000525 No 106 Sanlian Road Longhua Town Bao an District Shenzhen China Notes Only when the device is online on the tracking system it will send you back this SMS information 2 Longitude amp latitude tracking Format 888 password For example you send 888 000000 to the tracker you will get a reply SMS with link http map google com q 22 677327N 114 120738E SPEED 000 0 Date 12 05 28 Time 15 52 04 IMEI 353509000924608 Visit the link by your phone or computer you will know the name of the location in detail When there is no GPS signal you will get a repay SMS as follow MCCMNC 460010 LAC d1e3 CELLID 2535 Tracking on platform Please visit www gps288 com or www track188 com for online real time tracking and fleet management For details please refer to our tracking system user manual Notes 1 This non waterproof equipment please be sure to have waterproof bag No This equipment has to work with GSM network 3 Please ensure that there are enough expenses in SIM card in order to avoid the inconvenience of using 4 This equipment cannot work in the power failure state and outside the service areas even if the registered users 5 This equipment supports GPS and GSM GPRS double positioning regarding as the same with the GPS position
Download Pdf Manuals
Related Search