RF200D User Manual (PDF version)V1_2.pub
Contents
1. RS485 lines Care needs to be taken with the hardware connections to prevent the RF200D permanently transmitting data because of poorly connected cables It is advisable to use the above protocols Genlink amp Pelco if possible Page 13 RF200D Programming Data Channel Protocol Continued Listed below are the LED states for the data channel protocol Protocol Flashing LED s Static LED s Genlink Protocol Data Signal LED s 5 amp 6 Signal LED 1 Pelco P amp D Data Signal LED s 5 amp 6 Signal LED 2 Open Protocol Data Signal LED s 5 amp 6 Signal LED 3 Input Channels 1 amp 2 Transmit Pairing Signal When input channels 1 or 2 are flashing The RF200D is in Send Pairing Signal mode By briefly pressing the right button the signal LED s will flash a TX signal flashing from middle outwards to send the pairing signal to another RF200D device The receiving device will flash its signal LED 6 to indicate the reception of this pairing signal Send Pairing Signal Flashing LED s Static LED s Pair Input 1 or 2 Input LED s 1 or 2 Input Channels 1 amp 2 Set Input Mode Four possible modes are available see Hardware Description and are listed below Input 1 or 2 Mode Flashing LED s Static LED s Self Sense N 0 Input x Signal LED 6 Signal LED 1 Self Sense N C Input x Signal LED 6 Signal LED 2 Positive Trig 9V Input x Signal LED 6 Signal LED 3 Positive Trig 18V Input x Signal LED 6 Signal LE2. currently selected options When in configuration mode the currently selected option is shown by one or more LED s pulsing twice and the currently selected parameter shown by one or more of the signal LED s 1 4 To Enter configuration mode hold down switches 1 amp 2 for 3 seconds Once 3 Seconds have elapsed all the RF200D s LED s flash 3 times While in configuration mode switches 1 3 work as follows Switch 1 changes the current menu s option Switch 2 changes the currently selected parameter Pressing switch 1 for three seconds saves all the new settings flashes all of the RF200D LED s twice and reboots the system Pressing the tamper switch for five seconds exits configuration mode and switches off all LED s without saving new settings RF200D Pairing Example The RF200D follows the same procedure for pairing any input to an output including the data channel and repeat mode Listed below is an example to demonstrate how to pair a single input to an output The following pages in this manual describe the other configuration modes for pairing the remaining peripherals To pair an input to an output is as follows 1 Place both RF200D s in configuration mode 2 Select an output channel to pair first RF200D 3 Select an input channel you wish to pair from second RF200D 4 On the second RF200D press the right button The first RF200D s signal LED 6 should flash twice and the signal LED s 1 5 should increment 5
3. flashes twice and the bottom five signal LED s will increment by 1 Holding down the right switch for more than 3 seconds clears any previ ously paired devices from this channel It is only possible to pair a data channel with another data channel Listed below are the LED states for the data channel pairing Pair Data Channel Flashing LED s Static LED s 1 Device Paired Tamper LED Only Signal LED 1 2 Devices Paired Tamper LED Only Signal LED 2 3 Devices Paired Tamper LED Only Signal LED 3 4 Devices Paired Tamper LED Only Signal LED 4 5 Devices Paired Tamper LED Only Signal LED 5 Tamper Third Channel Local Tamper Switch Enable or disable local tamper switch This does not affect the local switches state being transmitted to other RF200D interfaces The options are as follows Tamper Switch Flashing LED s Static LED s Disabled Tamper Signal LED 6 Signal LED 1 on Enabled Tamper Signal LED 6 Signal LED 2 on Page 18 RF200D Programming Tamper Third Channel Status Update Monitoring Enable or disable status update monitoring When enabled any missing status updates generate a tamper fault and flash the tamper LED twice Status piro Monitori Flashing LED s Static LED s Disabled Tamper Signal LED 5 Signal LED 1 ON Enabled Tamper Signal LED 5 Signal LED 2 ON Tamper Third Channel Relay Test The RF200D has a build in relay test function When the tamper and signal LED s 5 amp 6 are flashing pressi
4. 00D s outputs To exit this mode again press switches 1 amp 2 for a brief second or replace the box cover for 5 seconds It is only advisable to enter one unit into site survey mode at any particular time Channel 1 or 2 Input Test Holding down either switch 1 or 2 for half a second sends the corresponding channel ON signal Any receiving device paired to this channel will activate its corresponding outputs Again this is useful for a engineer to check a channel is working correctly Tamper Switch Holding down the tamper switch for 5 seconds simulates the box lid being closed and switches off all of the internal status LED s The RF200D will also Send a status packet on the tamper switch changing state There is also a one Second delay when you release the tamper switch before the status LED s become active Holding down the tamper switch while in configuration mode for 5 seconds exits configuration mode without saving any new changes Page 8 Status Signal LED s Each input output on the RF200D has a closely mounted status LED to indicate the channel is active For the signal strength a strip of 6 LED s is mounted in the centre at the top of the RF200D A brief description of the status signal LED s is listed below Signal LED s The signal LED s have two meanings When the display raises from the bottom upwards this indicates a received signal strength depending on the receive level will depend on how many LED S will l
5. D 3 4 Devices Paired Output x LED Only Signal LED 4 5 Devices Paired Output x LED Only Signal LED 5 Note Output x Output LED 1 or 2 Page 15 RF200D Programming Output Channels 1 amp 2 Operational Modes The RF200D outputs can operate in three modes Momentary Toggle or Timer 1 Momentary means if any paired input is triggered the relay output is Switched on 2 Toggle mode causes its output to flip on detection of any positive going signal from a paired device 3 In timed mode any positive going signal from a paired device will either start the timer or reset the timer period to the beginning Output Mode Flashing LED s Static LED s Output x Signal LED Signal LED 1 Toggle Output x Signal LED Signal LED 2 Output x Signal LED Signal LED 3 Note Output x Output LED 1 or 2 Output Channels 1 amp 2 Timer Periods The RF200D allows various time periods per channel from 1 second to 30 minutes Listed below are the various timer periods Note Output x Output LED 1 or 2 Page 16 RF200D Programming Output Channels 1 amp 2 Relay Test The RF200D has a build in relay test function When the output and signal LED s 5 amp 6 are flashing pressing the right switch will turn on the outputs relay and signal LED 1 Tamper Output 3rd Channel Overview The tamper channel can work as a tamper relay or a third channel Pairing the tamper channel to any local or remote tampe
6. D 4 Note Input x Input LED 1 or 2 Page 14 RF200D Programming Input Channels 1 amp 2 Internal Input To Output Pairing The RF200D has an option to pair its own input to its own output One good reason for doing this is to use the RF200D as a timer but still transmit its status to other units You can only pair input 1 to output 1 or input 2 to output 2 The options are Input Output Pair Flashing LED s Static LED s Input Output Enabled Input x Signal LED 5 Signal LED 2 ON Input Output Dis Input x Signal LED 5 Signal LED 1 ON Note Input x Input 1 or 2 Output Channels 1 amp 2 Pairing In this mode the RF200D accepts a pairing signal from another RF200D Only inputs can be paired to an output unless the data channel has been configured for either the Pelco or Genlink protocol For each new paired device up to 5 units per channel the signal LED s 1 5 increment Holding down the right switch for more than 3 seconds clears any previously paired devices on the currently Selected output To pair a Pelco Aux command to an output ensure Pelco is already configured before entering configuration mode Press the Aux channel you wish to pair on the Pelco interface and the RF200D will learn its address and Aux channel Pair Outputs 1 or 2 Flashing LED s Static LED s 1 Device Paired Output x LED Only Signal LED 1 2 Devices Paired Output x LED Only Signal LED 2 3 Devices Paired Output x LED Only Signal LE
7. HF200D User Manual Issue 1 2 BOS a R2 22 Main Menu Main Menu Main Features Description Hardware Layout Hardware Description Outputs Power Supplies 5 6 6 7 Data Channel Basic RF200D Functions Status amp Signal LED s Additional Features RF200D Programming 11 12 13 14 15 15 16 17 17 18 19 20 20 21 General Data Channel Pairing and Baud Rate Data Channel Parity and Protocol Inputs 1 amp 2 Tx Pairing Signal and Input Mode Inputs 1 amp 2 Input to Output Pairing Outputs 1 amp 2 Pairing Outputs 1 amp 2 Operational Modes amp Timer Periods Outputs 1 amp 2 Relay Testing Tamper Third Channel Overview Tamper Third Channel Pairing amp Local Tamper Switch Tamper Third Channel Status Update Monitoring Repeat Mode Pairing RF Channel Selection Restore Factory Settings Specification IL o XL I II Page 1 Main Features Repeat Mode 7x RF Channels Site Survey Mode Easy Pairing Menu Encrypted Protocol DC9 14V Operation 433MHZz Licence Free Signal Strength Meter 250m Range in Ideal Conditions Requires Line of Sight 3 x Volt Free Relay Outputs 2 x Analogue Digital Inputs RS232 RS485 Data Channel IP65 All Weather Rated Enclosure Momentary Toggle amp Timer Outputs Genlink Pelco D amp P and Open Protocols Timer outputs From 1 second to 30 Minutes Internal Input to Output Pa
8. Save configuration by holding down switch 1 for three seconds 6 Test the connection by pressing the input channel switch for half a second and make sure the second box responds 7 Pairing complete Page 11 RF200D Programming Data Channel Pairing In this mode briefly pressing the right switch of the RF200D transmits a pairing Signal to another device If the RF200D receives a pairing signal from another device signal LED6 flashes twice and the bottom 5 signal LED s will increment 1 Holding down the right switch for longer than 3 seconds clears any previously paired devices from this channel It s only possible to pair a data channel with another data channel Listed below are the LED states for data channel pairing Pair Data Channel Flashing LED s Static LED s 1 Device Paired Data LED Only Signal LED 1 2 Devices Paired Data LED Only Signal LED 2 3 Devices Paired Data LED Only Signal LED 3 4 Devices Paired Data LED Only Signal LED 4 5 Devices Paired Data LED Only Signal LED 5 Data Channel Set Baud Rate In this mode briefly pressing the right switch changes the baud rate from 2400 to 19200 for the RS232 RS485 port The baud rate must match the other communicating equipment s baud rate to function correctly Listed below are the LED states for the different baud rates Flashing LED s Static LED s 2400 Baud Data Signal LED 6 Signal LED 1 4800 Baud Data Signal LED 6 Signal LED 2 9600 Baud Data Signal LED 6 Sign
9. ages from 0 to 24V DC from an external Source For digital switching voltages over 9V Mode3 or 18V Mode 4 switch the RF200D into an active triggered state Page 5 Hardware Description Outputs 1 amp 2 Both outputs are volt free with normally open normally closed contacts and are capable of switching loads of up to 1A 9 30V Under software control these outputs can be configured to work in either momentary toggle or timer mode The electrical connections are as follows Relay Outputs 1 amp 2 Normally Closed NC i Common Q HMQD Normally Open NO Output 3 Tamper Relay Output 3 has volt free contacts and can switch up to 500mA 30V This output can be configured to work as either a tamper circuit energised normally closed or a third channel Normally Open NO Please refer to the programming section to configure this output The electrical connections are as follows Tamper Output 3 Common Normally Open NO Power Supplies The RF200D works from a DC9 14V Max power supply The RF200D is also reverse polarity protected If using a separate power supply to drive the inputs please ensure the OV connections are commoned together Page 6 Hardware Description RS232 RS485 Data Channel The RF200D has a data channel with RS232 or RS485 supported Serial baud rates from 2400 to 19200 are possible with none odd or even parity Supported protocols are Genlink Pelco D amp P an
10. al LED 3 19200 Baud Data Signal LED 6 Signal LED 4 Page 12 RF200D Programming Data Channel Set Parity In this mode briefly pressing the right switch changes the parity for the RS232 RS485 port The parity must match the other communicating equipment s parity to function correctly Listed below are the LED states for the different parity settings Flashing LED s Static LED s Data Signal LED 5 Signal LED 1 Data Signal LED 5 Signal LED 2 Data Signal LED 5 Signal LED 3 Data Channel Protocol In this mode briefly pressing the right switch changes the selected protocol for the RS232 RS485 port Currently three protocols are available and are listed below 1 Genlink protocol This protocol is used for outputting all paired devices radio transmissions over either RS232 or RS485 port It is also possible to control a paired RF200D s outputs via this protocol A typical use for this protocol is expander modules extra I O channels Reading of an RF200D s analogue input voltages status monitoring in software door access control etc Please refer to the programming guide Pelco P amp D protocol This is mainly used for CCTV telemetry The RF200D automatically detects Pelco P or D and has built in support to pair Pelco AUX commands to any of the RF200D s three outputs see programming section Open protocol This protocol has no input filtering and will transmit any data sent through the RS232 or
11. d an open channel The electrical connections for both the RS232 and RS485 are listed below RS485 RS232 Rx Receive fo A Tx Transmit 191 CTS Clear To Lo A RTS Request To ov Aerial Connector A threaded M4 connector for mounting of the rubber duck aerial Please ensure the aerial has its supplied rubber washer fitted between the case and aerial and that the aerial is done up hand tight to create a waterproof seal If the washer is not fitted or the aerial is loose possible water damage may occur which is not covered under the product guarantee Programming Connector The programming connector is for firmware upgrades and PC configuration of the RF200D Do not connect anything to this connector other than the recommended programming tool Please if required contact your supplier for purchase information on the PC configuration programming tool Page 7 Basic Functions While the RF200D is in normal operation the three PCB switches have some engineer friendly features as listed below Site Survey Mode This mode sends out a beacon signal every second to assist the engineer in finding an ideal location for installing the RF200D You should aim for a minimum of 2 3 bars of signal strength for a reliable link By pressing switches 1 amp 2 together for a brief second the RF200D enters Site Survey mode Site Survey mode only sends out a beacon signal and does not control any of the RF2
12. et Case Rating Environmental Temperature Range Relative Humidity Page 22 DC9 14V DC Max 25mA Max 100mA Max 30V AC DC Volt Free 1A 500mA 25V Max 11 2K Ohms 433 32 434 52MHz 10mW 19 04 KHz 20KHz SSB 40KHz SSB RS232 or RS485 2400 19200 Genlink Open amp Pelco P D 115 x 65 x 40mm 305 x 65 x 40mm IP65 10 to 55 Degrees 95 Non Condensing Genie d GENIE CCTV LTD CCTV House City Park Watchmead Welwyn Garden City Hertfordshire AL7 ILT Tel 44 0 1707 330541 Fax 44 0 1707 330543 www geniecctv com Edition GN October 2012 vous C
13. he transmitter e g a power cut receiving automatic status updates will re sync the receiver 2 The receiver can also be programmed to detect missing status updates if two or more status updates are missing the receiver generates a tamper fault and the tamper LED flashes twice to indicate a remote tamper fault To enable status updates please refer to the programming section Input Channels Analogue Updates When an RF200D transmits a status update it measures the input voltages and transmits this level as a digital value in 0 1V steps The purpose of this feature is for remote data logging etc and has no affect on the inputs previously described Repeat Function An RF200D can repeat other RF200D s signals The repeating RF200D still can use its own inputs and outputs while repeating other units For an RF200D to repeat another units data it physically has to receive the first transmission and then re transmit this on the same frequency This is perfectly ok for status updates but for the data channel if a high data throughput is required we cannot guarantee its operation RF Channel Selection Seven RF channel channels are available in the 433 434MHz band All RF200D units must be on the same channel for them to communicate If a particular channel is found to be poor it is advisable to try another channel Page 10 RF200D Programming The RF200D is configured by a software menu system using the status and signal LED s to show the
14. ight For a transmission the LED s will pulse from the centre outwards Inputs Outputs 1 amp 2 The input output LED s for channels 1 amp 2 flash at half second intervals when a channel is active Channel 3 Tamper The status LED flashes at half second intervals providing the tamper fault is local if a remote tamper fault has been detected the status LED will pulse twice When using this output as a third channel the status LED will only flash at half second intervals when active Data Channel Data Models Only The status LED on the data channel emits a short pulse when sending or receiving data over the RS232 or RS485 port If the status LED stays on continuously for half a second or more there is a problem with either the serial port settings or the protocol used Power Saving During continuous data transmission the status signal LED s will dim this is normal behaviour to save power The status LED s also extinguish when the tamper switch is held down for more than 5 seconds Page 9 Additional Features Status Updates When an RF200D s inputs change it automatically transmits an status update This is a normal procedure but if the inputs do not change for a while the receiver does not know if the transmitter is still functioning correctly To overcome this the RF200D can be programmed to transmit a status update at a given period Status updates have two main functions 1 If a receiver becomes out of sync with t
15. iring For Timer Function Missing Status Update Monitoring Signal Jamming Page 2 General Description The RF200D is a full featured 433MHz wireless interface designed for short range transmissions The heart of the RF200D is the XE1205 radio transceiver which gives the RF200D full bi directional communication for its inputs outputs serial data and repeat functions Cased in an IP65 rated enclosure the Rf200D is designed for indoor and outdoor use Each RF200D has two input channels which can accept either an analogue input signal from 0 to 24V DC for remote monitoring or a digital signal set by 4 thresholds Outputs 1 amp 2 are volt free relay contacts and can be configured to work in three modes momentary toggle and timed outputs with intervals from 1 second to 30 minutes An option to pair its own input to output allows the RF200D to work as a timer as well as transmitting its status to other paired devices The third output can be switched between a tamper relay and a third channel In tamper mode the RF200D can monitor local and remote tamper switches lost status update signal from remote units or report a paired input from a remote unit When not used as a tamper circuit the third channel can function as a momentary volt free output Other features include a built in signal strength meter site survey mode for the engineer to check signal strengths when installing units and a RS232 RS485 serial interface for transmissio
16. n of protocols Pelco P amp D and any open channel protocol Page 3 Hardware Layout Aerial Connector Program ming ooooo E a c o 2 v E 0009699 p JO A zindino CI Co Co ae ggesu z o o im ssejelIM ZHINEEF Q002 H Programming Data channel only on certain Status Channel L3 Page 4 Hardware Description Inputs 1 amp 2 Listed below are the four modes of operation for Inputs 1 amp 2 Mode 1 Self Sensing Normally Open Input In this mode the RF200D outputs a sensing pulse to check to see if there is an open or short circuit present Idle state is represented by an open circuit where an active state is represented by a short circuit A typical example would be an open collector output from an alarm panel etc Normally Closed Active Normally Open Idle State R 0 203 D Mode 2 Self Sensing Normally Closed Input In this mode the RF200D outputs a sensing pulse to check to see if there is a open or short circuit present Idle state is represented by an short circuit where an active state is represented by a open circuit Typical examples would be a magnetic door contact or a PIR sensor Normally Closed Idle Normally Open Active 220 D D Modes 3 amp 4 Positive Trigger either 9 or 18 volts Modes 3 amp 4 accept positive volt
17. ng the right switch turns on the relay and signal LED 1 Status Update Period Enabling the status updates forces the RF200D to transmit its status at a given period even if there are no input changes If a receiving RF200D has its status update monitoring enabled and there is a loss of signal a tamper fault will be generated T Tamper Input 1 amp 2 LED s Signal LED 4 ON Tamper Input 1 amp 2 LED s Signal LED 5 ON Tamper Input 1 amp 2 LED s Signal LED 6 ON Page19 am y i m RF200D Programming Repeat Mode Pairing In this mode briefly pressing the right switch of the RF200D transmits a pairing Signal to another device If the RF200D receives a pairing signal from another device signal LED 6 flashes twice and the bottom five signal LED s will increment Holding down the right switch for more than three seconds clears any previously paired devices from this channel When pairing a RF200D repeat all functions from the RF200D will be repeated Up to five RF200D units can be repeated Listed below are the LED states for repeat mode pairing Pair Flashing LED s Static LED s 1 Device Paired Input 1 amp 2 Alternating to Output 1 amp 2 Signal LED 1 2 Devices Paired Input 1 amp 2 Alternating to Output 1 amp 2 Signal LED 2 3 Devices Paired Input 1 amp 2 Alternating to Output 1 amp 2 Signal LED 3 4 Devices Paired Input 1 amp 2 Alternating to Output 1 am
18. p 2 Signal LED 4 5 Devices Paired Input 1 amp 2 Alternating to Output 1 amp 2 Signal LED 5 RF Channel Selection The RF200D has 7 RF channels and defaults to channel 5 Below is a list of all the channel numbers and their corresponding frequencies Channel 7 434 52MHz Signal LE Page 20 RF200D Programming Restore Factory Settings This option resets the RF200D back to factory default and erases any previously paired devices When selected all the status LED s flash together To reset the RF200D hold down the right switch and wait for the Signal LED s to increment from 1 to 6 this is a warning stating all set tings are about to be erased When the 6th LED is on there will be a short pause followed by the RF200D flashing all its LED s before rebooting Once the RF200D has rebooted it will have restored its factory defaults and erased any previously paired devices Page 21 Specification Electrical Operating Voltage Operating Current Idle Operating Current All Relays amp LED s Relays Max Working Voltage Relay Contact Type Relay 1 amp 2 Max Current Relay 3 Tamper Relay Max Current Input 1 amp 2 Voltage Input 1 amp 2 Resistance Radio Operating Frequencies Transmit Power Radio Data Rate Deviation Bandwidth Data Channel Only on certain models Interface Type Baud Rate Protocols Mechanical Case Size without Aerial and Grommet Overall Size with Aerial and Gromm
19. r functions automatically configures the third channel s output into tamper mode In tamper mode the relay is per manently energised while no tamper fault has been detected This is a fail safe System to prevent a power failure not showing as a tamper fault Setting any of the following configures the third channel as a tamper channel 1 Enable local tamper switch 2 Enable missing status updates 3 Pair any remote RF200D s tamper channel It s also possible to pair a standard input from a remote RF200D to the tamper channel A standard input from a remote RF200D will not switch the third chan nel into a tamper channel but it can be used as another tamper input When a remote input is being used on a tamper channel triggering the input switches off the tamper relay i e the signal is inverted This can be a useful feature if you wish to report back a remote tamper state from a bell box or PIR etc If none of the above have been enabled or paired the tamper relay works as a third channel In this mode the normal state is Normally Open The only sup ported mode for this channel is momentary Note When the local tamper switch is disabled its status is still transmitted to other RF200D devices Page 17 RF200D Programming Tamper Third Channel Pairing In this mode briefly pressing the right switch of the RF200D transmits a pairing Signal to another device If the RF200D receives a pairing signal from another device signal LED6
Download Pdf Manuals
Related Search