ST-2000S_UG - CHAUVET® Lighting
Contents
1. CHAUVET Value Innovation Performance Technical Specifications Power 120V 60Hz AC 230V 50Hz AC Fuse 20mm Glass 1A Fast Blow 20mm Glass 1A Fast Blow Lamps 1 x 75W Xenon 1 x 75W Xenon Part No CH1000B Part No CH1000B Dimensions 267 x 216 x 216mm 10 5in x 8 5in x 8 5in Weight 3 6kg 7 85lbs User Information Please complete for your records Date Purchased Serial No Dealer Stamp Model ST 2000S TECHNO STROBE 2000S CHAUVET Value Innovation Performance TECHNO STROBE 2000S ST 2000S Users Guide Please read these instructions carefully before use World wide Headquarters 3000 North 29th Ct Hollywood Florida USA FL 33020 Tel 1 954 929 1115 Fax 1 954 929 5560 www ChauvetLighting com At the Rear At the Rear Rotary Speed Control Mode selection switch 1 4 Mono Plug for Linking gt Sound sensitivity knob Voltage Selector Not on European Model Mounting Bracket A A a J Fuseholder ee os Lens Fig 1 Introduction Congratulations on the purchase of your new CHAUVET lighting effect We are confident you will enjoy many trouble free hours with this unit To assist with the care and use of the product we have prepared this short guide Operation This lighting effect has been designed to function on a mains power supply of either 120V 60Hz or 230V 50Hz and has been fitted with a suitable power plug for use with your local voltage Check the label on the unit and th2. as use of any other lamp type may cause the unit to be non operational Due to the nature of xenon lamps it is vitally important that you do not touch the new replacement lamp with your fingers as this will reduce lamp life considerably Once again a tissue or cloth can be used for fitting the replacement lamp Finally before using check that the lamp is housed correctly in the lamp holder and that the plastic lens has been screwed back into place Replacing Fuses If the unit does not function at all when connected to the main power supply i e does not illuminate after replacing the lamp Then it is highly likely that the fuse has blown Disconnect from main power supply before attempting to replace either lamp or fuse In order to replace the fuse disconnect from the main power supply and then unscrew the fuse holder cover to reveal the fuse The unit has a label attached that indicates the correct fuse rating or you may refer to portion of this guide labeled Technical Specifications It is most important that replacement fuses are of correct rating Failure to use the correct fuse could damage the unit beyond economic repair The fuse should simply be placed inside the holder and the screw cap replaced Reconnect to main power Cleaning The most important part of your lighting effect to keep clean is the lens as this allows the light output to transmit This should be cleaned with a soft damp cloth The body of the unit may also be clea
3. e power plug for the correct voltage The Techno Strobe 2000S has two modes of operation sound activated and automatic The choice is make via the mode selector switch at the rear of the unit When operating in sound activated mode the sound sensitivity knob must be adjusted for the proper setting In automatic mode the speed control will adjust the flash rate 1 4 mono plug allows for linking When linking strobes there is a maximum of 8 strobes per any chain The first strobe will act as a Master CHAUVET also offers a large verity of strobe controllers and controllers that have the capability of operating this strobe Installation Mounting This unit has been designed to be hung It is recommended that for safety purposes your lighting effect be properly mounted using a suitable hanging clamp and safety cable CHAUVET offers a range of items which are ideal for safe mounting Replacing Lamps 1 Disconnect from main power supply before attempting to replace either lamps or fuse 2 Ensure that the unit is sufficiently cool before removing blown lamps 3 Never touch new lamps with your fingers use a tissue or a cloth In order to replace the lamp disconnect from main power supply first and unscrew the plastic lens on the front of the unit fig 1 The CH100B replacement lamp has the positive leg marked with a red dot Please take care to insert this leg into positive terminal in the unit Only use the appropriately rated lamp
4. ned in the same way We recommend internal cleaning be carried out by a fully qualified technician Maintenance amp Servicing Work on internal parts should be carried out by a qualified technician Removal of any covers other than the lens cover is considered a breach of warranty and will not be covered under any such agreement unless authorized first by the company Troubleshooting e If the unit is not functional check main power supply is on and check fuse e If the unit is functional but lamp does not light lamp may require replacing If after trying this solution you still have a problem contact your dealer or CHAUVET Caution To avoid overheating do not operate this unit in fast strobing mode for more then 20 minutes continuously No user serviceable parts please refer to CHAUVET for service Power Connections The unit is supplied with a power plug appropriate to its voltage and destination Should any other connections be required they must be carried out with the following configuration Earth Green Yellow cable Neutral Blue cable Live Brown cable In the USA amp Europe it is required that all plugs are 3 pin type i e with Earth Ground connection In the UK it is required that all mains plugs are fitted with 5A fuses
Download Pdf Manuals
Related Search