Digital Wireless Satellite Receiver with Digital Recorder SRT 6300
Contents
1. Switch 22 kHz If you are using a 22 kHz tone to select different satellite dishes or bandwith to Master make the 22 kHz tone switch enable or disable to select dish or LNB Note Ifthe LNB Frequency is set to Universal LNB 9750 10600 or 9750 10650 9750 10700 7 9750 10750 it is impossible to set 22 kHz because it is a default setting in this application 23 www strong tv STRONG DIGITAL TV DiSEqC Version You can choose Tone Burst DiSEqC 1 0 DiSEqC 1 1 or Disable Tone Burst allows two satellite dishes to be connected to the Master at the same time DiSEqC 1 0 and 1 1 allow multiple antennas to be connected to the Master at the same time If you are using five or more fixed antennas or LNBs then it is recommended using a DiSEqC 1 1 switch DiSEqC Port Choose to which DiSEqC Input your selected dish is connected to Tone Burst has two options Tone A for port 1 and Tone B for port 2 DiSEqC 1 0 has four ports DiSEqC 1 1 has sixteen ports Transponder To test your settings you can choose a transponder with a strong signal If your settings are correct then the level and quality banners should show a signal Dish Type Choose the Dish Type you use Fixed DiSEqC 1 2 USALS The default value is Fixed If you choose DiSEqC 1 2 then press the OK button to enter DiSEqC 1 2 Setup menu If you choose USALS then press the OK button to enter USALS Setup menu Channel Setup To go to Channel setup menu dir2. Main System Main Processor Memory HDD Front Panel amp RCU 7 KEYs VFD 2 LEDS RCU Conditional Access Interface PCMCIA DIGITAL TV DVB S 75 Ohm IEC 169 24 950 2150 MHz 10 80 dBm 27 5 MS s Vertical 13 V DC Horizontal 18 V DC Current Max 500 mA Overload protection 22 kHz 2 kHz 0 6 Vpp 0 2 V V1 0 1 1 1 2 1 3 compatible QPSK 1 45 Mbps SCPC MCPC MPEG 2 TS Specification ISO IEC 13818 MPEG 2 MP ML 4 3 16 9 720 x 576 PAL 720 x 480 NTSC MPEG 1 Layer 1 2 3 ST 15100 Flash ROM 8 MBytes RAM 64 MBytes EEPROM 1 kbits 160 GB CH VOL MENU OK STANDBY Time Service name and other info STANDBY amp POWER ON 47 keys 2 slots DVB common interface Standard www strong tv 39 STRONG DIGITAL TV A V amp Data In Out TV SCART VCR SCART S Video RCA A V S PDIF RS 232C USB RF Modulator RF Connector Output Service TV standard Power Supply Input Voltage Type Power Consumption Protection Physical Specification Size W X H X D Weight Net 9 2 Slave MPEG Transport Stream A V Decoding Profile Level Aspect Ratio Video Resolution Audio Decoding Video CVBS RGB Y C Output Audio L R Output Video CVBS RGB Output Audio L R Output Video CVBS RGB Input Bypass Audio L R Input Bypass Video S VIDEO Output Video CVBS Output Audio L R Output Digital Audio or Dolby AC 3 bitstream Output 9 pin CD SUB type Trans
3. The most common modules are made to open only 1 scrambled channel This will allow Master or Slave to open a scrambled channel Using 2 modules with 2 cards allows you to open 2 scrambled channels at the same time This means one scrambled channel can be recorded and the other one watched on Master or Slave There are also CAM modules on the market which can open 2 3 or more scrambled channels at the same time These modules allow you to open more scrambled channels from the same transponder frequency This is a good choice to use such kinds of modules for the SRT 6300 W receiver Using these CAM modules it allows you to record a scrambled channel to HDD watch another channel with the Master and watch a third one with the Slave or even open a scrambled channel on second Slave unit For maximum freedom in watching scambled channels insert an extra CAM module with card This allows you to watch scrambled channels from different transponders frequencies In order to display the module s and messages on screen correct select in menu Common Interface the correct capacity of the CAM module Select between Single Double Triple or Multi Note To open scrambled channels faster set the PMT function in menu Common Interface to OFF 30 www strong tv STRONG DIGITAL TV 6 0 FUNCTION GUIDE 6 1 Channel List Press OK button to see the Channel list when watching the live programme The Channel List displays the fol
4. 42 www strong tv Environmental Issues STRONG ENVIRONMENTAL ISSUES STRONG is committed to reducing the impact of its products on the environment To maximise the benefits of our design enhancements your co operation is required Electronic product recycling Do not dispose of this product with your domestic rubbish At the end of its useful life this product contains materials which when processed correctly can be recovered and recycled By participating in the responsible recycling of this product you will be reducing the requirement for new raw materials and reducing the amount of material that would otherwise end up in landfill When you purchase a new similar product your retailer may offer to take this old one off you Alternatively you can take it to your local recycling centre Your retailer or local municipal authority will advise you of the collection facilities available for waste electronically products in your area User of this service will be free to you Within the scope of the European legislation on Waste Electrical and Electronic Equipment Directive 2002 96 EC valid as of August 2005 STRONG provides a recycling system free of charge for consumers to returning products after end of life For more information about STRONG s environmental policy to you www strong tv select About us and Environmental Policy from the submenu DIGITAL TV Packaging on When disposing of th
5. The batteries should not be recharged disassembled electrically short circuited or be mixed or used with other types of batteries 2 0 YOUR RECEIVER 2 1 Master SRT 6300 W Front Panel STRONG STANDBY 6300 cits sesiterecsne 1 4 2 1 MENU Display the menu on screen 2 STANDBY The power button of the Master ON STANDBY or SERVER mode 3 OK Display channel list on screen Select an item in the menu 4 VOLUME Change audio level 5 CHANNEL Change the channels 6 VFD DISPLAY During the STANDBY mode the current time is displayed When the power is on the current status is displayed 2 2 Master SRT 6300 W Rear Panel 1 2 3 4 5 g bd Ojai ODS OVO SCART ON 3 S0 280 V soro ir B EA aa 2 A OFF e oema wh 67 8 910 11 12 13 1 TUNER 1 Connect to the satellite coax cable coming from the dish 2 TUNER 2 Connect to the satellite coax cable coming from the dish www strong tv STRONG 9 2 SY ES VCR DVD SCART ANT IN SWITCH VIDEO OUTPUT AUDIO RIGHT OUTPUT AUDIO LEFT OUTPUT S VIDEO OUTPUT 10 TV SCART 11 TO TV 12 S PDIF 13 SERIAL PORT DIGITAL TV Connect the VCR SCART to VCR DVD recorder Connect the TV antenna Main power switch Video output yellow Audio output Red Audio output White Connect the S Video input of your TV Connect the TV SCART to TV SCA
6. Press button once more to chancel a reservation n PN Note you can add only 8 Timers During recording of a programme you can not search v channels and reorganize channels www strong tv 33 STRONG DIGITAL TV 6 9 Play Files DVR File Playing a recorded file the info box will be seen with the File name Duration time and the buttons you can use You can enter the time to jump to the exact time by pressing the numerical keys Note Goto function only works when the info box is displayed and you can enter hour minute second MP3 File To remove a song from the list locate the cursor on that song then press SUB button PIC File If you play a JPG file you will see the info box as the above Press EXIT to go back to Media Base 6 10 Stop m To stop playing a DVR video or playing MP3 press STOP button m You can stop recording and stop Time Shifting by pressing STOP button m In picture mode press STOP button to show Display Mode list 6 11 Pause Pause from LIVE video Enable Time Shifting the LIVE picture will be changed to time shifted playback The video continues from the paused image when resumed from PAUSE Pause from Time Shifting The video continues from the paused image when resumed from PAUSE Pause from DVR video The DVR video continues from the paused image when resumed from PAUSE Pause from Pictures The slide show continues from the paused image when resumed from PAUS
7. STRONG DIGITAL TV 5 5 2 5 System Info You can check the System Model Software Version Hardware Version Loader Version Manufacturer Website and Serial Number information 5 5 2 6 Factory Reset All settings will be reset to factory default values 5 5 3 LNB Setup Master Only The Low Noise Block down Converter LNB amplifies the signal received by the satellite dish and lowers the frequency of the signal The signal is then fed from the LNB at the dish via cable to the Master For the LNB setting move the cursor to installation and press OK button Then move the cursor to LNB setting and press OK button Satellite Press OK button to display the Satellite List Select one of the pre programmed satellites that correspond to the direction of the antenna If the desired satellite name is not on the list select Other Connection Type The default value is Twin LNB you can change it to Separated Note Ifyou change the Connection Type all channels will be deleted Tuner Select a tuner for channel searching from the selected satellite LNB Frequency Select the L O Frequency of the used LNB The LNB Frequency 5150 11300 11450 9750 10600 9750 10650 9750 10700 9750 10750 can be selected with VOL VOL buttons You can enter LNB frequency also by using Numeric keys on the remote control The most used setting are the universal LNB settings 9750 10600 LNB Power Select LNB power ON to output the LNB voltage
8. Volume Button VOL Decrease the volume Move cursor to left Service down and move cursor down 25 MENU Button MENU Display the Menu on screen or return to previous menu from submenu www strong tv STRONG DIGITAL TV 26 EXIT Button EXIT Return to the screen Play Button RED Start playback with normal speed 2 N Return to normal speed of forward playback Pause Button GREEN Pause the playback Start the Time Shifting 29 Fast Rewind Button YELLOW Fast rewind 2 co Start reverse playback Change the speed of reverse playback 30 Fast Forward Button BLUE Start fast forward or fast motion playback Change the speed of forward playback Media Button MEDIA Go to the Media Base menu 32 Record Button Start recording 33 STOP Button STOP Stop time shifting playback or recording 34 Continue Button AROUND Continue playing a file 35 Slow Rewind Button lt 41 Start reverse slow motion playback 3 Change the speed of slow motion playback 36 Slow Forward Button I gt Start forward slow motion playback Change the speed of slow motion playback 37 Set Bookmark Button BOOK Make a bookmark while playback 38 Go to Bookmark Button BOOK2 Go to the bookmarked position 3 0 INSTALLATION First connect the satellite antenna cable and TV to the Master unit There are some of the most common ways to connect the equipment in this manual There are several
9. a folder locate the cursor on the file or folder you want to copy then press RED button You can t copy a file or folder to root directory Delete a file or a folder locate the cursor on the file or folder you want to delete then press GREEN button You can t delete a file or folder to root directory www strong tv 29 STRONG DIGITAL TV Stop USB Device first move the cursor to the right column then press TV RAD button to choose the device you want to stop if you have more than one device plugged in then press YELLOW button to stop the device Note Ifa USB storage is plugged into a Slave you can not see the file list under the Master 7 and the other Slave s Base Transfer menu If there is an unknown device please make sure the partition type isn t NTFS 5 9 Common Interface Master Only With inserted Conditional Access Module you will get information about your CAM smart card subscription status manage maturity rating and PIN codes of the smart card in this menu If the module hasn t been installed the phrase Not installed will display Content of the menu depend on the module type Please refer to the user manual of your module Note To get maximum benefit and access to open the scrambled channels it is very important 7 to choose the right CAM module s for your satellite receiver SRT 6300 W Please ask your local dealer to find the right CAM module for the programmes you want to watch
10. Digital Wireless Satellite Receiver TRONG with Digital Recorder SRT 6300 W DIGITALTV Digital Wireless Satellite Receiver SRT 630 WS 4300 un User Manual SRT 6300 W SRT 630 WS www strong tv TABLE OF CONTENTS 1 0 INTRODUCTION 1 1 Safety Instructions 1 2 Storage 1 3 Equipment Set up 1 4 Introduction 1 5 Features amp Accessories 2 0 YOUR RECEIVER 2 1 Master SRT 6300 W Front Panel 2 2 Master SRT 6300 W Rear Panel 2 3 Slave SRT 630 WS Front Panel 2 4 Slave SRT 630 WS Rear Panel 2 5 Remote Control 3 0 INSTALLATION 3 1 Master SRT 6300 W 3 2 Slave 3 3 Wireless Network Configuration 4 0 QUICK START 5 0 MENU OPERATION 5 1 Main Menu 5 2 Channel Organizer 5 3 Favourite Organizer 5 4 Timer Setup 5 5 Installation 5 6 Media Base 5 7 Media Base Management 5 8 Media Base Transfer 5 9 Common Interface Master Only 6 0 FUNCTION GUIDE 6 1 Channel List 6 2 Information Box 6 3 EPG Electronic Programme Guide 6 4 Subtitle 6 5 Teletext 6 6 Sound Track 6 7 Time Shifting 6 8 Recording STRONG DIGITAL TV Aa A HRW WwW o o N DTH N 10 T 13 15 17 17 17 18 19 20 21 28 29 29 30 31 31 31 32 32 32 32 33 33 www strong tv STRONG DIGITAL TV 6 9 Play Files 6 10 Stop 6 11 Pause 6 12 Slow Motion Playback 6 13 Fast Forwarding and Rewinding 6 14 Bookmark 6 15 Repeat 6 16 Picture In Picture PIP Master Only 6 17 Keyboard 7 0 TURN OFF SYSTEM 7 1 Mast
11. E 34 www strong tv STRONG DIGITAL TV 6 12 Slow Motion Playback To playback in slow forward motion without sound press the I gt button The slow forward motion can be adjusted by pressing the 4 button repeatedly To playback in slow rewind motion without sound press the 4 button The slow rewind motion can be adjusted by pressing the 4 button repeatedly There are two steps 0 25X 0 5X in slow motion playback Press gt button to resume playback with normal speed ot Ne e P The slow motion is only available for the playback Note Only on DVR and Time shifting you can use slow motion playback Radio programmes support only slow forwarding 0 25X 0 5X 6 13 Fast Forwarding and Rewinding 1 To go to the desired playback position press 44 or gt gt button 2 Press 44 or gt gt button repeatedly to change the speed There are six speeds 2X 4X 8X 16X 32X 64X 3 Press gt button to resume playback with normal speed 4 When playing MP3 press 44 button to play pervious file and press gt gt button to play the next file 5 When watching pictures press 44 button to go back to the pervious picture and press gt gt button to the next picture Note Only on DVR and Time Shifting you can use fast forwarding an rewinding Radio programmes only support Fast forwarding 2X 6 14 Bookmark You can jump to a position directly by bookmarking the fun
12. GITAL TV 6 7 Time Shifting 1 To use Time Shifting function press GREEN button to display Time Shifting progress bar and pause the current LIVE programme Press RED button or GREEN button once more to continue the current LIVE programme 2 To go to the desired playback position press YELLOW or BLUE button These functions are valid while the Time Shifting progress bar is displayed 3 To stop Time Shifting function press STOP button 4 To start Instant Time Shifting press AROUND button The start position of the playback go 10 seconds back by pressing AROUND button 6 8 Recording There are three kinds of recording Recording LIVE Programme Timer recording recording by EPG Recording LIVE Programme Press button to record the LIVE programme you are watching To stop the recording press STOP button A list will be shown then you can stop the recording Note Master or Slave s only can stop their own recording Timer Recording Go to Timer Setup menu you can add a timer by pressing RED button In order to start a Timer on the Slave the Master shouldn t be powered off and should use the same Transponder as the Slave when sharing a tuner You can check Timer status in Timer Setup menu Note Only 8 Timers you can add Recording by EPG Press EPG button in the LIVE mode to display EPG Select a service you want to record press button and then choose Daily or Weekly record
13. Network that is capable of delivering multiple video and audio streams through out a consumer s household The SRT 6300 W System contains of a Master and Slave unit The Slave s get the signal from the Master through a wireless network connection The SRT 6300 W system is fully compliant with the DVB S standard is designed to be capable of upgrading its software from a USB device It is highly recommended that you read this manual carefully to safely install your receiver and to achieve its optimum performance www strong tv STRONG DIGITAL TV 1 5 Features amp Accessories SRT 6300 Wireless Digital Satellite Receiver with Digital Recorder MPEG 2 Digital and fully DVB compliant One Master box two Slave boxes or one Master box one Slave box For all Free To Air digital TV and Radio programmes 2 Common Interfaces compatible to all major Conditional Access Modules Cryptoworks Viaccess Conax etc 5 000 channels TV and Radio programmable Channel list edit delete sort Four Favourite lists for both TV and Radio programmes Favorite channel list edit delete sort Three Recording and Playback Simultaneously 1 x on Master 2 x on each Slave Recording capacity 88 hours for 4 Mbps stream with 160 GB HDD Powerful trick mode supported include Time loop Fast Forwards and Back Slow Forwards and Back Pause Resume and Time Shift USB 2 0 support USB mass storage devices using FAT file system MP3 MPEG 1 Layer 3 p
14. RT input Connect the TV RF IN for TV without scart Optical output for Digital Audio RS 232 Port 2 3 Slave SRT 630 WS Front Panel wn 22 ey a STRONG STANDBY STANDBY The power button of the Master ON STANDBY MENU Display the menu on screen OK Display channel list on screen Select an item in the menu VOLUME Change audio level CHANNEL Change the channels LED Display the current time or current status LINK If Slave has been connected Master the LED Green will be on RECORDING If Slave is recording a programme the LED Blue will be on www strong tv STRONG DIGITAL TV 2 4 Slave SRT 630 WS Rear Panel AUDIO RIGHT OUTPUT Audio output Red ik 2 AUDIO LEFT OUTPUT Audio output White 3 VIDEO OUTPUT Video output Yellow 4 S VIDEO OUTPUT Connect the S Video input of your TV 5 TV SCART Connect the TV SCART to TV SCART input 6 VCR DVD SCART Connect the VCR SCART to VCR DVD recorder 7 S PDIF Optical output for Digital Audio 8 DC INPUT DC power input 2 5 Remote Control 1 Power Button i Switch the box between Operation Standby or Server Mode 2 MUTE Button X Enable Disable the audio output of the receiver 3 Numerical Buttons 0 9 Select the TV or Radio channels and menu operations 4 RECALL Button ROTATE Select the previously viewed channel 5 INFO Button i Display the programme infor
15. ction in playback Use bookmarks for searching positions very quickly and easily Add a bookmark To add bookmark press BOOK button at the position you want to add it Go to a bookmark Press BOOK2 button to jump to the bookmark Then the DVR video starts from the bookmarked position Delete a bookmark To remove a bookmark you have to stop the DVR video first Then press BOOK button Note Only DVR play has bookmark function www strong tv 35 STRONG DIGITAL TV 6 15 Repeat In Time Shifting mode Press AROUND to start Instant Time Shifting The start position of the playback go 10 seconds back by pressing AROUND button In DVR play mode Press AROUND button to repeat playing the current file Press AROUND button once more to cancel the repeated playback In MP3 play mode Press AROUND button to repeat playing the current file Press AROUND button once more to cancel the repeated playback In PIC mode Press AROUND button to rotate the picture 6 16 Picture In Picture PIP Master Only 1 In the LIVE mode press PIP button to display PIP Press PIP button repeatedly to change the size of sub picture or to remove the sub picture 2 At PIP screen press PIP2 button to exchange main picture with sub picture Note It is not possible to exchange main picture with sub picture during recording and Time Shift 3 To display the service list of main pictures press OK button Select a se
16. e N Er 3 2 Slave 3 2 1 Connection to TV VCR and HiFi 1 Connection to the TV with the SCART Cable Connect one end of the SCART cable to the TV SCART socket on the Slave and the other end to a SCART socket on the TV TELEVISION www strong tv 13 STRONG DIGITAL TV 2 Connection to the VCR with the SCART Cable Connect one end of the SCART cable to the VCR SCART socket on the Slave and the other end to a SCART socket on the VCR TELEVISION nO z for VCR 3 Connection to the TV with the CINCH Cable Connect one end 3 connectors of the CINCH cable to the AUDIO RIGHT red AUDIO LEFT white and the VIDEO output yellow sockets on the Slave Connect the other end 3 connectors to the AUDIO RIGHT red AUDIO LEFT white and the VIDEO input yellow sockets on the TV or Hi Fi TELEVISION 4 Connection to the TV using the S VIDEO Connect one end of the S VIDEO cable to the S VIDEO socket on the Slave and the other end to the S VIDEO socket on the TV and connect the S PDIF output to your Digital Audio Amplifier TELEVISION DIGITAL AUDIO Optical AMPLIFIER s Poir I 14 www strong tv STRONG DIGITAL TV 3 3 Wireless Network Configuration Note Ifyou start using Slave s please do the following steps to set up wireless conn
17. e Motorized DiSEqC 1 2 and the USALS items according to your antenna LNB and satellite settings If the right Satellite Name and LNB Frequency were not found in the list call the dealer for satellite information Then press OK button at Channel Setup item and go to the Channel Setup menu Set the Search Mode to Auto Transponder or Network Move to Start Search item and press OK button The search procedure will take a while After searching has finished press OK button and it will switch to LIVE programme 0 Turn on the Slave s Zo Mn aL 5 0 MENU OPERATION Now this chapter assumes that the system has been installed correctly meaning The satellite antenna dish for the Master has been installed and connected to the Master and the Master and Slave are connected to TVs The remote control has batteries and is ready to control Master and Slaves If the system has not been installed or connected properly please refer to the INSTALLATION menu on this manual 5 1 Main Menu Many functions of the systems are available from the Main Menu Press MENU button to open the Main Menu Note Some functions and menus are only own by Master www strong tv 17 STRONG DIGITAL TV 5 2 Channel Organizer 5 2 1 Channel Organizer Master This menu can be used to sort edit and delete TV and Radio Services Note The default menu is under TV menu press TV RAD to switch to Radio menu or swi
18. e listed in two columns on the screen with TV channels in one column and Radio channels in the other Please note that the search process may take a few minutes When the search process is completed the screen will show how many TV and Radio channels have been found Press OK button to save the channels Note When Master finishes searching Slave s will get automatically an update of the 7 Channel List LNB Setup To go to the LNB Setup menu directly from Channel Setup menu press the OK button 25 www strong tv STRONG DIGITAL TV 5 5 6 DiSEqC Setup Master Only Satellite You can not change the satellite here It is the same satellite as you choose at LNB Setup menu Tuner Select You can not change the Tuner here It is the same Tuner as you choose at LNB Setup menu Transponder Select a transponder to catch a strong signal Press OK to display the transponder list Command Mode User mode The movement is adjustable by single steps Installer mode The movement is adjustable by East West commands continuous movement Movement User mode Select how many steps you want the dish to move Installer mode Move the dish continuously Motor Control m Goto Move the motor to the stored position of the selected satellite m Reset Reset all the stored positions of the motor relative to the 0 position m Limit OFF Remove the limitation m Limit W Set the limits of West position m Limit E Set the limi
19. e then the menu will be showing Note The supported languages can be changed without any notice Audio Language 1 It is a selection for changing the language of the Audio If more than one audio language is transmitted you may select any one of them Note The supported languages can be changed without any notice Audio Language 2 It is a selection for changing the language of the Audio too It only works when the broadcaster doesn t support Audio Language 1 If more than one audio language is transmitted you may select any one of them Note The supported languages can be changed without any notice 5 5 2 2 Connection The STB has many connections You have to control this screen button properly according to external components connected to the STB Configurations concerning audio and video can be made here TV Mode Select your TV standard For automatic PAL NTSC selection set it to Multi Video Output Select the mode of Video output between CVBS and RGB TV Format Select your TV screen format 4 3 16 9 or Auto mode Audio Output It allows you configure the sound mode Select the Stereo Left or Right audio mode Aspect Ratio Mode You can select the display format Select the Normal Letter Box Pan and Scan or Combined mode www strong tv 21 STRONG DIGITAL TV SPDIF Output You can enable or disable the S PDIF digital output in this menu VCR Output Select a VCR output Terminal or Aut
20. ection 7 Otherwise you can skip the following steps 1 First turn on the Master If the Master is in standby mode press the Standby key to switch ON the Master 2 During system is booting press OK key to open Wireless Network Configuration menu in Master 3 Ifthe Master is not registered with the Slaves Master will go to search for the Slave automatically 4 Turn on a Slave and the TV set The Language Selection menu will be seen next on the screen Choose the language and confim with OK If the Slave is not registered to any Master the Slave will reboot and enter the wireless Network Configuration automatically In case it does not start automatically you can access directly after booting by pressing OK 5 The Slave will connect and register to the Master automatically At the same time the Slave will get the Master s ID and the Master will get the Slave s ID automatically 6 On Slave side the message Registered to Master successfully will be shown on the TV screen 7 On Master side the message Do you want to register another one will be shown if you want to register another Slave Select YES and repeat steps 4 6 in order to register another Slave Select NO to go back to Wireless Network Configuration 8 After having registered one or two Slave s with the Master press Exit GREEN button on the Master s remote control After the Master has restarted confirm the registration also on the Slave s w
21. ectly from LNB setting menu press the OK button 5 5 4 Channel Setup Master Only Satellite Press OK button to display the Satellite List Select one of the pre programmed satellites that correspond to the satellite dish If the desired satellite name is not in the list select Other Tuner Select a tuner for channel searching Search Mode There are 3 search modes Auto Transponder and Network The Auto mode enables you to search using the information the Master has On the other hand you may need to know in advance the frequencies and the symbol rates when you use transponder mode When you use the Network mode the NIT Network Information Table is available the Transponder s information can be found Frequency Select or enter the Transponder s Frequency by using the numeric buttons on your remote control 24 www strong tv STRONG DIGITAL TV Polarization Choose the type of polarisation either the Horizontal or the Vertical Symbol Rate Enter the Transponder s Symbol Rate by using the numeric buttons on your remote control Scan Mode You can select only searching free channels or all channels included scrambling channels Start Search To start the searching process press OK button at Start Search To stop the searching progress on the way press either the MENU button or the EXIT button This menu will be shown as long the STB is searching for channels All channels found will b
22. eign objects fall through the ventilation slots because this could cause fire or an electric shock Do not place any objects on top of the receiver because this might prevent proper cooling of the components inside m Before connecting the cables be sure that the receiver is disconnected from the main power supply Make sure you read this user manual before installing your receiver It is highly recommended that you read this manual carefully to safely install your receiver and to achieve its optimum performance Note The batteries should not be recharged disassembled electrically short circuited mixed 7 or used with other types of batteries Safety Precautions Do not open the receiver cover as you will be exposed to a shock hazard It will also void your warranty Refer all maintenance or servicing to suitably qualified personnel m When you are connecting the cables be sure that the receiver is disconnected from the mains supply voltage Wait a few seconds after switching off the receiver before you move the receiver or disconnect any equipment m Itis a necessity that you only use an approved extension and compatible wiring that is suitable for the electrical power consumption of the installed equipment Please ensure that the electrical power supply corresponds with the voltage on the electrical identification plate at the back of the receiver If the receiver does not operate normally even after strictly following of the instructions in th
23. er 7 2 Slave 8 0 SOFTWARE UPDATE 9 0 SPECIFICATIONS 9 1 Master 9 2 Slave 10 0 TROUBLESHOOTING 34 34 34 35 35 35 36 36 37 38 38 38 38 39 39 40 42 www strong tv STRONG DIGITAL TV 1 0 INTRODUCTION 1 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER m In a closed or poorly ventilated cabinet directly on top of or under any another equipment on a surface which might obstruct the ventilation slots DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES m To direct sunlight or near any other equipment that generates heat to rain or intense moisture to intense vibration and to any shock which may cause permanent damage to your receiver or to any magnetic objects such as loudspeakers transformers etc Do not use a damaged power cord It may cause a fire or an electrical shock Do not touch a power cord with wet hands It may cause an electric shock m Never open the cover It is dangerous to touch the inside of the receiver due to high voltage currents and possible electrical hazards Your warranty will be void if the receiver has been opened m When the receiver is not used for a long period of time you should unplug the power cord from the wall socket Do not use alcohol or ammonia based liquids to clean the receiver If you wish you may clean your receiver with a soft lint free cloth slightly made damp with a mild soap solution only after disconnecting from the mains voltage supply Make sure no for
24. fer rate 115 2 kbps USB 2 0 Device 75 Ohm IEC 169 2 Female Male CH 21 69 PAL NTSC PAL G I K NTSC selected by Menu 90 240 V AC 30 W AC Fuse 340 x 265 x 60 mm 3 35 kg MPEG 2 MP ML 4 3 16 9 720 x 576 PAL 720 x 480 NTSC MPEG 1 Layer 1 2 3 Main System Main Processor ST 15100 Memory Flash ROM 8 MBytes RAM 32 MBytes EEPROM 1 kbits 40 www strong tv STRONG Front Panel amp RCU 7 KEYs 4 digital 7 segment LEDs 3 LEDs RCU A V amp Data In Out TV SCART VCR SCART S Video RCA A V S PDIF USB Power Supply Input Voltage Type Power Consumption Protection Physical Specification ITEM Specification Size W X H X D Weight Net a DIGITAL TV CH VOL MENU OK STANDBY Time Service name and other info Link Record Power on Standby 47 keys Video CVBS RGB Y C Output Audio L R Output Video CVBS RGB Output Audio L R Output Video CVBS RGB Input Bypass Audio L R Input Bypass Video S VIDEO Output Video CVBS Output Audio L R Ouptut Digital Audio or Dolby AC 3 Bitstream Output USB 2 0 Device 10 4 12 6V DC 11 W DC Fuse 165 x 60 x 160 mm 1 06 kg Note Specification and functions may be changed for improvement without notice in v advance www strong tv 41 STRONG DIGITAL TV 10 0 TROUBLESHOOTING Occasionally the receiver may hang up In that case it is recommended to reset the receiver by disconnecting i
25. he S VIDEO Connect one end of the S VIDEO cable to the S VIDEO socket on Master and the other end to a S VIDEO socket on the TV and connect the S PDIF output to your Digital Audio Amplifier DIGITAL AUDIO Optical p AMPLIFIER 5 PoIr TELEVISION 3 1 2 Connection to the Satellite Dish It is important to decide which type of connection between receiver and LNB will be used The simplest connection type and the one we recommend to use is Twin LNB It will require the installation of a TWIN LNB and two cables between LNB and receiver The connection type SEPARATED can be used if you have installed antennas for more than one satellite With this connection type you can use different antenna connections for example you have a fixed dish with single LNB connected to SAT IN of TUNER 1 and a motorised dish with single LNB connected to SAT IN of TUNER 2 1 Installing Master with two separate Satellite Dishes The Connection Type in LNB Setup menu should be set to Separated 12 www strong tv STRONG DIGITAL TV 2 Installing Master with Twin LNB in Satellite Dish The Connection Type in LNB Setup menu should be set to Twin LNB OL CE io b GEF ceo a ED oo gee i 3 Installing Master with two separated Twin LNB Satellite Dishes and DiSEqC switches The Connection Type in LNB Setup menu should be set to Separated 1 Gay O ce n
26. is ot Ery h product packaging please ensure that it is recycled Packaging material is to be depolluted in waste separation Power Saving To save power and money please put the product into standby mode when not in use We also recommend disconnection from mains supply when not in use for longer periods of time Batteries Do not dispose of the batteries A S from your handset with your domestic waste Where they are available participate in your local municipal or retailer collection schemes for spent batteries Batteries discarded in landfill sites or incinerated increases the chances of pollutants being dispersed into the atmosphere Alternations reserved 09 2009 www strong tv STRONG Environmental Issues DIGITAL TV www strong tv
27. is user manual it is recommended to consult your dealer www strong tv 3 STRONG DIGITAL TV 1 2 Storage Your receiver and its accessories are stored and delivered in a packaging designed to protect against electric shocks and moisture When unpacking it make sure that all the parts are included and keep the packaging away from children When transporting the receiver from one place to another or if you are returning it under warranty make sure to repack the receiver in its original packaging with its accessories Failing to comply with such packaging procedures could void your warranty 1 3 Equipment Set up We recommend you consult a professional installer to set up your equipment Otherwise please follow the instructions below m Refer to the user manual of your TV and your antenna m Make sure that the SCART cable and outdoor components are in a good condition and the SCART connections are well shielded This manual provides complete instructions for installing and using this receiver The following symbols will serve as follow A Warning Indicates warning information Note Indicates any other additional important or helpful information MENU Represents a button on the remote control or the receiver Bold Character Move to Represents a menu item within a window Italic Character 1 4 Introduction Thank you for choosing the SRT 6300 Wireless Home Media Network The SRT 6300 W System is a Wireless Home Media
28. ith OK The Slave s will restart and connect to the Master 9 You can see wireless network configuration information by pressing OK button when system is booting Note Please make sure the Channel Network Name Network Density settings are the same for Master and Slave s Otherwise the Slave s can not connect to the Master Save To save your configuration after changing the information press the Save RED button Exit Exit the Wireless Network configuration by pressing the Exit GREEN button Default By pressing the Default YELLOW button you will set all settings to factory default Note if you set the Master to factory default all registered Slaves will get unregistered and 7 you need to register them again www strong tv 15 STRONG DIGITAL TV Unregister Master only Move the cursor down to the Slave you want to unregister Press the Unregister BLUE button to unregister it If you want to change wireless configuration press the OK button to enter Wireless Network Configuration menu when the system is booting In the Wireless Network Configuration menu you can change Channel Number Network Name Network Density in order to get the best quality m Channel Number Auto and channels 1 11 can be chosen Setting this channel number appropriately provides one way to avoid sources of wireless interference m Network Name You can change the network name on Master and both Slaves by locating the cursor
29. layer browse and play MP3s stored in a storage device USB and internal HDD JPEG Viewer browse edit zoom in out and do a slide show of JPEGs in storage devices USB and internal HDD File manager manages copying and deleting of files directories in storage devices USB and internal HDD Distribution of smooth digital TV streams to up to 3 TVs in a household through cutting edge Wireless MIMO technology Highly efficient self dominated Intellectual Property Right Network protocol RapidMedia Protocol Electronic Programme Guide provides you detailed programme information DVB Subtitle supported and selectable audio tracks Teletext via OSD Dual Decoding PIP only Master S PDIF for digital audio Parental Lock protects access to menu and or programmes DiSEqC 1 0 1 1 1 2 and USALS DiSEqC 1 3 Timer function can automatically record programmes daily or weekly Easy recorder programming by EPG up to 7 days in advance User friendly menu available in various languages English German and Dutch Automatic channel search system with selectable options VFD display in front panel showing programme number time or play function Supports software downloading via USB stick 2 SCART connectors TV VCR 3 RCA connectors Video and Audio out S Video output RF modulator PAL 1 B G D K NTSC M www strong tv 5 STRONG DIGITAL TV Accessories m User Manual Remote control units Batteries AAA type Warranty Card Note
30. lowing ies Satellite name Free Channels or Scrambled Channels Transponder an Polarization information RED button only in Master forcing to switch the channel GREEN button you can sort the channel list by alphabets Note Only Master can switch the channels between different Transponders Gray channels on the Slave s channel list mean these channels cannot be watched If you choose Separated as Connection Type you see T1 Tuner 1 or T2 Tuner 2 beside Channel Name 6 2 Information Box Press i button on the remote control to see the programme Information The Information Box displays as follows Channel Number Programme type F means Free if the programme is scrambled sign will be displayed If you see a T it means this channel provides Teletext If you see a S it means this channel provides Subtitle Signal Level Signal Quality EPG information Current Time Programme start time and end time You can hide the Information Box by pressing i button SF Note Ifyou see AC3 in the info box means this channel provides AC3 sound If you choose Separated as Connection Type you will see T7 Tuner 1 or T2 Tuner 2 beside Current time www strong tv 31 lt gt 7RONG DIGITAL TV 6 3 EPG Electronic Programme Guide To display the information of current and following TV programmes press the EPG button on your remote control If EPG of programmes i
31. mation box on the screen and remove it and show extended EPG information 6 PIP Button PIP Enable Resize and Disable sub picture 7 PIP Swap Button PIP2 Exchange the main picture and Sub picture at the PIP 8 PIP List Button PIP3 Display the channel list of the sub picture 9 PIP Move Button PIP4 Move the position of sub picture by clockwise 8 www strong tv STRONG DIGITAL TV 23 Volume Button VOL Increase the volume Move the cursor to right 24 CH Button CH DIGITAL TV 10 SAT Button SAT Display the satellite list 11 TV STB Button TV Change the terrestrial TV and STB mode 12 PAGE Button PAGE Move the selection bar in menu 13 Audio Button AUDIO Select Sound Track and LEFT RIGHT MONO STEREO sound 14 TV RAD Button TV RAD Select the TV Radio mode 15 PAGE Button PAGE Move the selection bar in menu 16 FAV Button FAV Display the favourite channel list 17 EPG Button EPG Display the EPG on screen when available Remove EPG when EPG is displayed 18 Teletext Button TEXT Enable the Teletext 19 Subtitle Button SUB Activate the subtitle selection window Select the subtitle language in the list In the Media Base menu go to Media Base Management menu In the Media Base Management menu go to Media Base menu 20 CH Button CH Service up and move cursor up 21 OK Button OK Display Channel List on screen Select an item in the menu 22
32. o switch between DVR MP3 PIC tab Note USB storage device won t be displayed in this menu In this menu you can delete a file or folder by pressing the RED button If you want to delete a crypto folder you must enter the right PIN code All the files or folders will be permanently deleted Press GREEN button to create a folder You can create either public or crypto folder by choosing the different types If you choose to create a crypto you must enter the password Rename the file or folder by pressing YELLOW button If you want to rename a crypto folder you must enter the right PIN code You can also move a file by pressing BLUE button then a directory list will display If you want to move a file or a folder to a crypto folder you must enter the right PIN code You can t move a file or a folder to root directory Note Ifyou see a file name is yellow that means this file is recording now and you can not 7 delete rename and move this file 5 8 Media Base Transfer The left column displays the files and folders on the HDD The right column displays the files and folders on the USB storage device MP3 files will be shown in MP3 type a JPG file will be shown in PIC type Press TV RAD button to change types Also only MP3 files and JPG files will be shown on right column If you have plugged in more than one USB storage device you can press TV RAD button to change different USB storage devices Copy a file or
33. omatic RF Modulator Master Only When the Master is connected to the TV set with a RF cable you may need to select the correct TV standard Select the PAL B G PAL I PAL D K mode by using UP DOWN buttons The default RF modulator is PAL B G RF Channel Master Only Select a RF channel by using UP DOWN buttons The default channel here is 38 When you change the RF channel number you must also change the same value on the TV If you do not there will be no picture and sound 5 5 2 3 Menu Setting Transparency Adjust the OSD transparency of all menus The available levels are from 0 to 4 Brightness Adjust the OSD brightness of all menus The available levels are from 0 to 2 Duration Adjust the time out of the Info Box Set the duration time that the Info Box is displayed on screen The adjustable time is from 7 Sec to 6 Sec 10 Sec 20 Sec and 30 Sec 5 5 2 4 Time Setting The exact local time can be adjusted by using the GMT usage Time zone Adjust time and Date sub menus GMT Usage GMT is referred to the standard time of Greenwich It can not be changed Time Zone Here you can choose your time zone Adjust Time You can adjust time only when GMT usage is OFF Enter the current time by using the numeric buttons Date You can type the date mm dd yyyy by using the numeric buttons but the GMT Usage must be OFF a Note We recommend to setup the same time for Master and Slaves s 22 www strong tv
34. on Network Name then press OK button to display the keyboard The network name is limited to 32 characters Note Network name can only be English letters and numbers m Network Density Use low network density for maximum range Use high network density for maximum robustness of interface protection Note Ifyou want to change Slave s Wireless Configuration the Master should be in the Wireless 7 Network Configuration Menu as well On Master and Slaves all parameters should be set the same If a Slave has been registered with another Master you will see a Master ID but the circle is red the Slave should be set to default first 16 www strong tv STRONG DIGITAL TV 4 0 QUICK START Press the POWER button to turn on the Master Now the Info Box will appear on the bottom of the screen for a certain time and then disappear By pressing i button the Info Box will remain on the screen The display time of the Info Box can be adjusted in the Installation menu of the Menu Setting A IMPORTANT Before using your new receiver some important technical settings are essential 1 First press the MENU button on the remote control the Main Menu will appear 2 Go to the LNB Setup menu in the Installation menu and press OK button 3 Choose the right parameters for Satellite Tuner LNB Type LNB Power LNB Frequency DiSEqC Switch DiSEqC Input DiSEqC Repeat Switch 22kHz and Channels Setup 4 Set th
35. rvice in the service list To display the sub picture s service list press PIP3 button 4 Press PIP4 button to move the sub picture s position 36 www strong tv STRONG DIGITAL TV 6 17 Keyboard The keyboard will be displayed when you change file name folder name channel name and favourite group name There are two keyboards you can use m Standard Keyboard m Extended Keyboard RED Use the Standard keyboard GREEN Use the Extend keyboard YELLOW Save and exit the keyboard BLUE Delete the last entry 37 www strong tv lt gt 7RONG DIGITAL TV 7 0 TURN OFF SYSTEM 7 1 Master Press the POWER button on Master There are two options you can select next m Power Off Turn off Master Next time press POWER button to turn on Master Note If Slaves are connected to Master the small circle beside Slave 1 and Slave 2 is green 7 otherwise they are red turn off the Slaves first m Server Mode The Master will be in server mode and provides all services to the Slaves If you want to leave the server mode press the POWER button Master will work normally 7 2 Slave To turn off the Slave just press POWER If the Slave lost connection you will see Poor Wireless Signal Quality Searching Master on the Slave screen after a few seconds you will see the message Connection Lost At this time you can choose Reboot the or Turn off the Slave Ifthe Mas
36. s broadcasted you will see the detailed description of the programmes start end time and programme schedules etc RED Display the current programme schedule and detailed description GREEN Display the next programme schedule and detailed description YELLOW Display the current channel weekly schedule BLUE Display the reserved schedule TV RAD Change the contends of EPG between TV and Radio services To reserve a programme or channel a reserved programme 6 4 Subtitle To watch subtitles press SUB button for displaying the subtitle language list and choose the language you want Then press the OK button If the broadcaster provides subtitles you can see S symbol in the Information Box 6 5 Teletext If the broadcaster supports Teletext you can see a T symbol in the Information Box Press the TEXT button to watch the Teletext You can enter the page number by pressing the numerical buttons on the remote control Home Go to the Home page Next Go to the next page Prev Go to the previous page Pause Start Pause or start the Teletext Exit Exit the Teletext Also you can press colour buttons for page selections 6 6 Sound Track You can choose a language of soundtracks by pressing AUDIO button when the broadcaster supports various languages of soundtracks Also you can choose a mode among Stereo Mono Left and Right using VOL VOL buttons 32 www strong tv STRONG DI
37. t from the main power Wait 30 seconds and connect to main power again then see if the unit is working as expected If the receiver does not work properly after checking the trouble shooting section please contact your dealer Do not open the receiver cover it may cause an electric shock due to high voltage and the warranty of your receiver will be void No picture and sound Check the coax cable Replace the cable or connect the cable tightly to the receiver Set the values of tuner parameters correctly Check the signal strength adjust your dish correctly The display on front panel Check if the power cord is connected to the wall outlets does not light up The receiver displays the If it is winter check if there is snow covering the dish message No Signal Press the SAT button on the RCU and select the correct satellite Check the settings in LNB and Channel setup menu Ask your dealer to check the outdoor unit and antenna cable to LNB The remote control does not Check if the batteries are inserted correctly in your remote control work Check the batteries and if exhausted replace them Slave can not connect to Check if Master is working Master Check if all the parameters are same in Wireless network configuration menu for both Master and Slave Slave displays the message Adjust the direction of the antenna on the Slave or Master Poor Signal Change the Network density in Wireless network configuration menu
38. tch back to TV menu MENU OPERATION Sort Press Sort RED button Than you can choose Name by alphabet Type Free or Scrambled TP Transpond or Manual to sort and rearrange the channel list by pressing different colour buttons Fav You can add services to different favourite groups Locate the cursor to desired service and press Fav GREEN button Then choose a favourite group by pressing different colour buttons Edit You can change a channel name skip and hide a channel In order to change a channel name locate the cursor to the desired channel and press Edit YELLOW button Then press OK button and type a name you want After you have finished press OK button In order to lock a channel select the channel you want to lock press YELLOW button and move the cursor down to Lock Then press OK button to prevent children from watching it You can unlock the channel by the same way If a channel has been locked you should enter the PIN code in order to enjoy it In order to skip a channel mark the desired channel press Edit YELLOW button Then press OK button on the skip option The skipped channels will not be visible on the channel list Delete Press Delete BLUE button then there will be three buttons you can choose from 1 Press One RED button to delete a channel 2 Press All GREEN button to delete all the channels 3 Press Return BLUE button to go back to the Channel Organizer menu No
39. te Deleted channels are permanently deleted The only way to recover them is to perform a new channel search 5 2 2 Channel Organizer Slave You can add services to different favourite groups Locate the cursor to the desired service and choose a favourite group by pressing different colour buttons 18 www strong tv STRONG DIGITAL TV 5 3 Favourite Organizer This mode is helpful in organizing your favourite channels There are four buttons you can use sort next edit and delete a Note The default menu is under TV favourite channel menu you can press TV RAD to v switch to Radio favourite channel menu or switch back to TV menu Sort Press RED button Here you can sort and rearrange the favourite channel list by Name Type TP or Manual by pressing different colour buttons Next There are four groups Digital News Sport and Music for TV and four groups for Radio Digital News POP and Jazz The default group list is Digital Press GREEN button to switch between the group list Edit Press YELLOW button the keyboard will appear Type the name you want then press OK button Delete Locate the cursor on the desired channel Then press BLUE button to delete the channel Note Deleted channels are just deleted from the Favourite group You can still find them in 7 the channel list www strong tv 19 STRONG DIGITAL TV 5 4 Timer Setup Timer information can be found in men
40. ter has been turned off you will see Master is power off and you can reboot or power off the Slave Note If Master has been rebooted the Slaves should be rebooted as well 8 0 SOFTWARE UPDATE Although the SRT 6300 W System has stable and convenient software to use a new system software may be released To add or modify functions the system software has to be updated The latest software and manual will be found at STRONG s website www strong tv With this menu only Master you can update your firmware via USB stick USB Update 1 Download the update software from the website and copy the file onto a USB stick 2 Turn on all Slave s Select route on Slave s MENU Installation Software Update page Let them stay in this menu 3 Plug the USB stick into the USB connector behind the flap on the front of the Master 4 Turn on the MASTER and go also to Software Update menu 5 Press the OK button to enter USB and select the update file then press Update RED button to start updating 6 After the update has finished the Master and Slave s will reboot automatically 38 www strong tv STRONG 9 0 SPECIFICATIONS 9 1 Master Double Tuners Input Loop through Connector Frequency Range Signal Level input LNB Power amp Polarization 22 kHz Tone DiSEqC Demodulation Input Symbol Rate MPEG Transport Stream A V Decoding Transport Stream Profile Level Aspect Ratio Video Resolution Audio Decoding
41. th VOL VOL buttons or numeric buttons Reference Position Go to the Reference position Move You can turn the antenna clockwise or counter clockwise to exact position with VOL VOL buttons Goto the Position After having set the Longitude Latitude of your local position and the longitude of the selected satellite this function is used when you want to move antenna to the desired direction position which you have saved before Up One Level Go back to the LNB setup by pressing the OK button 5 5 8 Parental Lock You can lock or unlock the menu and change the PIN codes in this menu The default PIN is 0000 5 5 9 HDD Function Master Only Power Save Set the time to make Hard Disk HD go to save mode by itself when the HD does not work The default value is 5min but you can set it to Imin 2min 5min 15min 30min and 60min Format To format the Hard Disk Drive HDD select this option and press the OK button Formatting the Hard Disk Drive will permanently delete all data and files stored on HDD You can t use TimeShift record files listen to MP3s and watch pictures with an unformatted HDD Note Only Master has HDD www strong tv 27 STRONG DIGITAL TV 5 5 10 Software Update In this menu you can update your system by using a USB stick The Slave s must be in the same menu while updating the software 5 6 Media Base To enter this menu you can press MEDIA button or on the main men
42. ts of East position m Goto Ref Go to reference m Store Store the current position of the motor for the selected satellite Up One Level Go back to the LNB setup by pressing the OK button 5 5 7 USALS Setting Master Only USALS is a very convenient motorized DiSEqC system that supports DiSEqC 1 3 commands and can also get the satellite position automatically if you now your geographical location Basically the listed satellites have its Longitude and therefore the angle of the satellite can be calculated without problems If you have USALS motorized system then you can use the USALS as followings Satellite You can not change the satellite here It is the same satellite as you choose at LNB Setup menu Tuner You can not change the Tuner here It is the same Tuner as you choose at LNB Setup menu Transponder Select a transponder to catch a strong signal Press OK to display the transponder list 26 www strong tv STRONG DIGITAL TV Satellite Angle This is the orbital position of the selected satellite Normally this is set automatically but if you wish you can edit it manually with the numerical buttons on the remote control East or West will be selected with VOL VOL buttons My Longitude It means the longitude of your location You can select the angle East and West with VOL VOL buttons or numeric buttons My Latitude It means the latitude of your location You can select the angle South or North wi
43. u Timer Setup To insert a new Timer entry press RED button Press Modify GREEN button to edit the entry By pressing Delete YELLOW button you delete the selected entry OT One Time D Daily W Weekly R Record TI Time Interval S Success F Failed Initiation Action Press VOL VOL buttons to choose Record or Start Time Tl on Action Begin Date Enter the date mm dd yyyy directly by pressing numerical buttons Begin Time Select the recording duration by pressing VOL VOL buttons then pressing numerical buttons are available Duration Select the recording duration by pressing VOL VOL buttons or use the numerical buttons to enter a value directly Mode By Using VOL VOL buttons select One Time Daily and Weekly Satellite Press OK button to display the satellite list Select a satellite that includes the channel to be recorded Prog Type Choose TV or Radio by using VOL VOL buttons Prog Name Press OK button the channel list will appear and then choose the one you want to record and press OK again Save To Press OK button the folder will appear Then choose a folder you want and press OK button 20 www strong tv STRONG DIGITAL TV 5 5 Installation 5 5 1 System Setup 5 5 2 1 Language There are different languages available for the menu languages Menu Language It is a selection for changing the language of the main menu Select the languag
44. u move the cursor to this screen button then press the OK button In this menu you can watch DVR on the HDD listen to MP3 or watch pictures on HDD or USB storage You can press VOL VOL buttons to switch between DVR MP3 PIC tab DVR Press RED button you can sort files Press OK button on a file you can start playing the file a Note USB storage won t be displayed in this TAB MP3 To enter this menu press VOL VOL buttons In this menu you can listen MP3 on HDD or USB storage To sort the MP3 files press RED button You can show the Playlist by pressing GREEN button Press YELLOW button you can clear the playlist To add an MP3 to the playlist you can move the cursor to the file and press BLUE then a green small circle will appear If you want to remove an MP3 from the playlist you can press BLUE button again and then the green small circle will disappear Press OK button on a file you can add it into the playlist and start playing the playlist PIC To enter this menu press VOL VOL buttons In this menu you can watch the pictures on HDD or USB storage Press RED button to sort the files Note Only JPG file can be displayed 28 www strong tv STRONG DIGITAL TV 5 7 Media Base Management Enter Media Base Management by pressing SUB button in Media Base menu You can also press SUB button to go back to Media base under Media Base Management Press VOL VOL buttons t
45. ways of connecting the receivers to the existing Audio TV system We recommend to choose one of the following setups If you have problems with your connections and need help contact your STRONG dealer 10 www strong tv STRONG DIGITAL TV 3 1 Master SRT 6300 W 3 1 1 Connection to TV VCR and Hi Fi 1 Connection to the TV with the SCART Cable Connect one end of the SCART cable to the TV SCART socket on the Master and the other end to a SCART socket on the TV TELEVISION 2 Connection to the DVD or Video Recorder with a SCART Cable Connect one end of the SCART cable to the VCR SCART socket on the Master and the other end to a SCART socket on the DVD or Video Recorder De E TELEVISION 3 Connection to the TV with the CINCH Cable Connect one end 3 connectors of the CINCH cable to the AUDIO RIGHT red AUDIO LEFT white and the VIDEO output yellow sockets on the Master Connect the other end 3 connectors to the AUDIO RIGHT red AUDIO LEFT white and the VIDEO input yellow sockets on the TV or Hi Fi www strong tv 11 STRONG DIGITAL TV 4 Connection to the TV using the RF Cable Connect a terrestrial antenna to RF IN socket on the Master Connect one end of the RF cable to the RF OUT socket of the Master Connect the other end to the ANT IN socket on the TV TELEVISION 5 Connection to the TV using t
Download Pdf Manuals
Related Search