contents SoundClip-8L user manual v1 - Blackbox-av
Contents
1. manner with a maximum of 99 tracks The SC 8L also has 8 light outputs as standard which can be configured to turn on off in a predetermined fashion when each button is pressed certain tracks are played 2 5SUPPORTED MEDIA FORMATS The Soundclip 8L supports audio in two formats mp3 We recommend all files used be in mp3 format if you have issues playing any audio content we recommend you convert your audio using Format Factory this can be downloaded for free here http www pcfreetime com 3 IN THE BOX SoundClip 8L Terminal Blocks Power Supply Screwdriver Plug Adapters MicroSD to USB converter MicroSD Card images for illustrative purposes only 4 SETUP INSTRUCTIONS Setting up your SC 8L is simple and straightforward You will need the following The SoundClip 8L 12V DC Power Adapter Buttons or PIR if using button or PIR activated content not included Headphones or speakers not included MicroSD Card with content on see programming section Terminal blocks for buttons and speakers Screwdriver for wiring terminal blocks Lighting if using lighting not included audio video interactive FRONT VIEW ON OFF i BUTTON VOLUME REEF 225 NICRO 0 DELAY MASTER Dina Agee oi VOLUME STATUS 12VDC CONFIGURATION www interpreatationshop uk2. 12VDCin Configuration Switche Adjust Volume Status LED Volume l 3 5mm output Adjust Delay MicroSD Slot Buttons REAR VIEW Light Output 1 8 SHT SC8L ONFIGURATION SPEAKERS _ am i gt Se Lighting Configuration Switches 12v Supply Speaker Speaker for PIR or Lighting Left Right Button1 Button8 1 Powering Your SC 8L Connect the supplied 12V DC Adapter to the 12V DC in to give power to the device 2 Connecting headphones to your SC 8L The SC 8L can support up to 2 headphones with the built in 3 5mm jack simply connect them via the headphone 1 and 2 output 3 Connecting Speakers Wire speakers to the Speaker Left and Speaker Right terminal block follow the and directions if appropriate insert wires and screw in place with provided screwdriver 4 Connecting Activation Buttons To utilise button activation of the SC 8L you must wire buttons to the designated terminals Simply insert button wire ends and screw in place using the provided screwdriver 5 Connecting Volume Buttons The SC 8L has dedicated volume terminals allowing you to give visitors the ability to increase or lower the volume Connect 2 buttons to the designated terminal to do so Simply insert button wire ends and screw in Page 2 place with the provided screwdriver 6 Connecting Lighting To add lighting we recommend LED strip lighting to the SC 8L you must
3. FRONT dipswitch into the UP off position to store the setting Now when track 001 plays lights 1 3 5 and 7 will turn on whilst the remaining lights will stay off Follow this procedure to program each track from 001 to 008 Note Any tracks above 008 will automatically turn all lights on Page 5 8 DELAY AND MASTER VOLUME CONTROL Two controls on the front of the device AN 9 r allow you to alter the Delay timer and T Master Volume DELAY MASTER F VOLUME Delay The delay control allows you to specify how long between playing content the unit must wait before more content can play This is mainly used in conjunction with a PIR input establishing how long between activation the unit must wait to play more content However it can also be used with all other modes if desired Switch 7 when Off up makes the delay control range from 0 60 seconds when On down it ranges from 0 4 minutes Master Volume The SC 8L has dedicated volume inputs to allow users volume control The Master Volume dictates the maximum volume available to them When powered up the SC 8L is set to around half the Master Volume level this allows users to reach the maximum volume through the use of dedicated button controls Bear this in mind when setting the Master Volume If you are providing users with the ability to adjust the volume themselves we recommend you set the volume to maximum through button controls when decidin
4. Down on position the SC 8L will be in Sequential PIR mode this means it will activate one audio track at a time via PIR sensor moving onto the next audio track in sequence after each activation This allows you to activate track 001 then 002 then 003 etc one at a time Page 4 7 LIGHTING CONFIGURATION As standard the lighting outputs will activate according to the track being played for example when track 001 is being played lighting output 1 will activate when track 002 is being played lighting output 2 will activate and so on If in looping mode the above will apply however should you have more than 8 tracks once tracks above 008 are playing all lighting outputs will activate How it works When programming the lighting outputs you will be programming how the SC 8L reacts to each track number from 001 to 008 Any tracks above this number i e 009 010 011 etc will by default activate all lighting outputs This means the lighting outputs will activate in the same manner whether track 001 008 are played via Looping Playback in Next Previous mode Play All mode or activated via the push of buttons 1 8 Programming the lighting outputs To program the lighting outputs you will need the number of tracks you wish to program 001 008 uploaded to the MicroSD Card and an equal amount of buttons connected 1 8 Without these tracks button presses will not be registered when in lighting c
5. SoundClip 8L user manual v1 contents 1 WHATISTHE 1 2 SUPPORTED MEDIA 1 3 IN THE 1 A SETUP WINS TRUGC TION edenienies 1 5 PROGRAMMING 2 6 CONTENT 3 7 LIGHTING CONFIGURATION u cccsccccssscscsssrccssseeceesees 4 8 DELAY AND MASTER VOLUME 5 STO a E E 5 8 button audio player with 8 Light Outputs July 2014 Ji bolackbox qv audio video __ interactive WELCOME Thank you for purchasing the SoundClip 8Lights The SC 8L is one of a range of products we offer specific to the heritage marketplace We are confident that we have other products you will find useful and look forward to hearing from you again soon T 44 0 1639 767007 W www blackboxav co uk 1 WHAT IS THE SC 8L The SoundClip 8L is from our range of compact stand alone high quality stereo audio players It can be used to present audio through headphones via two 3 5mm audio jacks or 2 speakers via wired terminal The SC 8L can present audio in a looping fashion or be activated via 8 buttons with one button for a single message each It can also work a Play all function upon button PIR activation or in a Next Previous
6. g what volume dial setting you require 9 STATUS LED Red On Off The red LED will be lit when unit is powered on and off when unit is powered down Green Status The Green LED will be lit when content is being played and blink on off in 1 second intervals when unit is in Delay Mode 1 m JE blackbox av to indicate this E audio video interactive
7. on 2 for m previous audio video interactive Page 3 When powered on in this mode the SC 8L will always start on audio file 001 it will then remain on the last file it played 5 Currently Unassigned 6 LCD amp Button Pad Activation Put in the down on position to place the SC 8L in compatability mode for the LCD display and Button Pad add on not included 7 Delay Range The delay control see section 8 DELAY AND MASTER VOLUME CONTROL allows you to determine how long between the end of an audio file a new file can be activated When switch 7 is in the Up off position the control ranges from 0 seconds when turned fully anti clockwise to 60 seconds maximum when turned fully clockwise When switch 7 is in the Down on position the delay control will range from 0 minutes when turned fully anti clockwise to 4 minutes when turned fully clockwise 8 Lighting Configuration Mode This switch will put the SC 8L into programming mode for the lighting outputs See 7 LIGHTING CONFIGUATION below for further programming instructions 8 Button Mode When all switches are in the Up off Position the SC 8L is in 8 button mode as standard this means Button 1 plays file 001 Button 2 plays file 002 etc With switch 1 in the Up off position files are interuptible put switch 1 in the Down on position to make playback uninterruptible Sequential PIR mode When switches 1 and 4 are in the
8. onfiguration mode 1 Enter Programming Mode Enter Light Configuration mode via the configuration switches located on the FRONT of the SC 8L Place dipswitch no 8 into the ON down position with the remaining dipswitches in the OFF up position CONFIGURATION 2 Enable Disable Lighting Outputs Once in Light Configuration mode the lighting configuration switches located on the REAR of the SC 8L become active Enable of Disable the lighting outputs by placing the associated dipswitches to either the ON down or OFF up position i audio interactive For example QQ Q 12345678 45078 DIP ON The above configuration sets light outputs 1 3 5 and 7 ON with outputs 2 4 6 and 8 OFF 3 Store settings for appropriate track With the light outputs set you need to store the configuration for each appropriate track To configure the track simply press the corresponding button Button 5 005 Button 6 006 Button 7 007 Button 8 008 Button 1 001 Button 2 002 Button 3 003 Button 4 004 Note you can only configure one track at a time you must press the no 8 configuration dipswitch located on the FRONT into the UP off position after each track is configured So with the above mentioned configuration press Button 1 the Green Status LED will remain solid when you press Button 1 to indicate it has been registered Turn the
9. ow this content is played is set via the dip swiitches located on the front of the device ON OFF BUTTON VOLUM MICROSD eee DELAY MASTER ma DIP STATUS www interpretationshop uk CONFIGURATION Configuration Switches Using a screwdriver click these switches into either a Down or Up position to turn On or Off Dip Switch Settings Down On Up Off 1 Interuptible Playback When switch 1 is in the Down on position the SC 8L is set to uninterruptible this means when file starts to play it will finish no matter if an additional input is activated When in the Up off position files can be interupted 2 Looping Playback When switch 2 is in the Down on position the SC 8L will be in looping mode All content on the MicroSD card will play in a sequential manner from power up and then begin again from the start The Delay control will specify how long the unit waits between tracks Tracks must be labelled sequentially 3 Play All When switch 3 is in the Down on position the SC 8L will be in Play All mode this means when triggered via button or PIR it plays through all audio files once When in this mode the SC 8L is uninteruptible even with switch 1 set to Up off 4 Next Previous When switch 4 is in the Down on position the SC 8L is in Next Previous mode This means users can navigate through all files on the MicroSD card by pressing button 1 for next and butt
10. these must be named 001 002 003 etc The order in which files play is determined by their name the first file must always be named 001 the second 002 and so on Properly named files can be added to the MicroSD card in bulk i e you can drag multiple files across onto the card as long as they are properly named Step1 Prepare your audio files for transfer we recommend you use mp3 files however wav files are also supported Rename them 001 002 003 etc depending on the order you want them played Step2 Insert the MicroSD card into the MicroSD USB convertor and connect to your PC Step3 Transfer all of your content onto the SD card OW 5 Computer Removable Disk H Organize Play Burn New folder A Jr Favorites a Mme Desktop 12 001 Format Sot Downloads 1 002 MP3 Format Sounc Dropbox 003 Format Souno H Recent Places 2 004 MP3 Format Sounc 2 005 MP3 Format Sounc Libraries 006 Format Sot L Documents 2 007 MP3 Format Sound al Music 008 Format Sount Pictures Videos sor Eam 7 001 Contributing artists Specify contributing artist PY MP3 Format Sound 003 Step4 Insert MicroSD card into the SC 8L test files play as planned How files are acivated is determined by how the dip switches are configured See following section 6 CONTENT CONFIGURATION Content is added to the SC 8L via MicroSD card h
11. wire them to the designated terminals To configure how this lighting is activated please see section 7 LIGHTING CONFIGURATION 7 Connect PIR SC 2 pictured The SC 8L can be PIR Passive Infra red activated to add a PIR you must wire i it into the 1 button terminal with the power connection wired into the 12v Out terminal as pictured on a SC 2 8 Add content to your SC 8L To add content to your SC 8L you must first transfer it to the supplied MicroSD Card and insert this into the MicroSD slot see 5 PROGRAMMING CONTENT below for more details 9 Configuring the SC 8L Deciding how the SC 8L is configured is completed using the Configuration Switches this determines if it s looping button activated or has a delay between content See 6 CONTENT CONFIGURATION for more details 5 PROGRAMMING CONTENT Content for your SC 8L is stored on the supplied MicroSD card To add content you will need 1 Audio Content in mp3 format supports up to 99 audio files 2 APC or laptop with Windows OS 3 MicroSD Card supplied 4 MicroSD to USB convertor supplied How the content you add will be played by the SC 8L will depend on how you configure it find out more on this in 6 CONTENT CONFIGURATION audio interactive The name of your audio files when added to the MicroSD card will determine the order in which they play Note The SC 8L supports up to 99 files
Download Pdf Manuals
Related Search