EC type-examination certificate UK/0126/0011 Revision 2
Contents
1. National UK 0126 0011 Measurement Office MI 006 EC type examination certificate UK 0126 0011 Revision 2 issued by The National Measurement Office Notified Body Number 0126 In accordance with the requirements of the Measuring Instruments Automatic Catchweighers Regulations 2006 SI 2006 1257 and the Measuring Instruments Non Prescribed Instruments Regulations 2006 which implement in the United Kingdom Council Directive 2004 22 EC this EC type examination certificate has been issued to Avery Weigh Tronix Foundry Lane Smethwick West Midlands B66 2LP United Kingdom in respect of an automatic catchweighing instrument as described in the descriptive annex and having the following characteristics 6000 e 20e Maximum capacity Max Minimum capacity Min Accuracy class Y a lt 2 The necessary data principal characteristics alterations securing functioning etc for identification purposes and conditions when applicable are set out in the descriptive annex to this certificate This revision replaces previous versions of the certificate Issue Date 06 June 2011 Valid Until 04 September 2017 Reference No T1110 0006 fle Signatory P R Dixon for Chief Executive Y BIS UKAS National Measurement Office Stanton Avenue Teddington TW11 0JZ United Kingdom CERTIFICATION Department for Business Tel 44 0 20 8943 7272 Fax 44 0 20 8943 7270 Web www bis gov uk nmo 0135 Innovation amp Skil2. body identification number Accuracy class Serial number Manufacturers mark or name Certificate number Operating temperature range 5 8 5 2 If the instrument is not permanently installed it shall be provided with a level indicator 6 LOCATION OF SEALS AND VERIFICATION MARKS 6 1 The CE marking supplementary metrology marking and certificate number are located on the mounting plate bracket which is fixed to the main structure of the conveyor stand The CE mark shall be impossible to remove without damaging it The data plate Figure 3 shall be impossible to remove without it being destroyed The markings and inscriptions shall fulfil the requirements of Paragraph 9 of Annex of the Directive 2004 22 EC 6 2 Access to the configuration and calibration facility for the 1310 weighing module s is via a push button located on the power supply PCB and is accessed through a hole in the rear of the indicators enclosure The plastic screw which prevents access to the push button can be secured to the back of the enclosure by a wire and seal Components that may not be dismantled or adjusted by the user including the load cell junction box if applicable must be secured by either a wire and seal or a tamper evident label and securing mark The securing mark may be either amark of the manufacturer and or manufacturer s representative or an official mark of a verification officer ALTERNATIVES 7 1 Having the sy
3. control panel contains the motor controls and associated power supplies 2 2 2 The control of the instrument is provided by the PC via I O modules The preset tare associated with the product is entered via the 1310 indicator and stored The PC requests weight data including preset tare values from the 1310 indicator 2 2 3 The 1310 weight indicator contains all of the electronics associated with the weighing process and is as described in EC Test certificate GB 1153 The PC runs the Avery Weigh Tronix Weight for Windows software package as described in EC Test Certificate GB 1010 This provides an electronic data storage facility with a unique consecutive number being generated and printed onto the label The PC provides a secondary indication of the weight and various status signals and is used to select the product being weighed 2 3 Load cell Any compatible load cell s may be used providing the following conditions are met There is a respective OIML Certificate of Conformity R60 or a Test Certificate EN45501 issued for the load cell by a Notified Body responsible for type examination under Directive 2009 23 EEC 2 8 2 4 2 4 1 2 5 2 5 1 2 6 2 6 1 The certificate contains the load cell types and the necessary load cell data required for the manufacturer s declaration of compatibility of modules WELMEC 2 Issue 5 2009 section 11 and any particular installation requirements A load cell marked NH is a
4. inted and applied to the packs is provided with a unique consecutive number which is generated by the Weight for Windows data storage device running on the PC 4 PERIPHERAL DEVICES AND INTERFACES 4 1 Interfaces The instrument may have the following interfaces Load cell connection hardwired 3x RS 232 RS422 1 x powered RS422 20 mA 4 2 Peripheral devices The instrument may be connected to any peripheral device that has been issued with a test certificate or parts certificate by a Notified Body responsible for Annex B MI 006 under Directive 2004 22 EC in any Member State and bears the CE marking of conformity to the relevant directives or A peripheral device without a test certificate may be connected under the following conditions it bears the CE marking for conformity to the EMC Directive it is not capable of transmitting any data or instruction into the weighing instrument other than to release a printout checking for correct data transmission or validation it prints weighing results and other data as received from the weighing instrument without any modification or further processing and it complies with the applicable requirements of Paragraph 8 1 of Annex I 5 APPROVAL CONDITIONS The certificate is issued subject to the following conditions 5 1 Legends and inscriptions 5 1 1 The instrument bears the following legends CE marking Supplementary metrology marking Notified
5. is used to synchronise the packs to ensure that the duplicate label is applied to the correct pack 2 6 2 lf an error is detected by the barcode scanner or if the pack is outside predefined weight limits an error signal is generated and the instrument is stopped The pack must then be removed from the system and the error acknowledged 3 8 3 TECHNICAL DATA 3 1 The instrument has the following technical characteristics ae 0 C to 40 C Climatic environment Non condensing closed Electromagnetic environment E1 and E2 Y a 6 core with braided outer screen 0 5 mm2 per core flexible PVC overall jacket Maximum length 5 m 10 m mm2 Load cell cable 3 2 Documentation and drawings 3 3 Software 3 3 1 The weighing software is contained within the 1310 indicator and the version number is 52957 0137 The application software is V1 1 The software version numbers are accessed by Hold in the escape key until the indicator beeps For the User Menu enter the password 111 and press the enter key From the User menu press the soft key marked VIEW From the View menu press the soft key marked VERS 4 8 3 3 2 The control software is contained within the PC and the version number is V 2 x where x covers minor software variants The software version number is accessed by pressing help amp about when the application is running 3 3 3 Each label pr
6. llowed only if humidity testing to EN45501 has been conducted on this load cell The compatibility of load cells and indicator is established by the manufacturer by means of the compatibility of modules form contained in the above WELMEC 2 document The load transmission conforms to one of the examples detailed in WELMEC 2 4 Guide for Load Cells Printer The printer is an Advanced Labelling Systems model ALX924 5 Devices The instrument is provided with the following devices Semi automatic zero setting device not operable during automatic operation Automatic zero setting device before every pack Zero tracking device Zero indicator Tare weighing or balancing device not operable during automatic operation Preset tare device Net indicator Gross B G indicator Real time clock Device to determine when stability criteria are fulfilled Operation Packs are delivered to the weighing conveyor by the in feed conveyor Once detected by the associated photocell the weighing conveyor is stopped by the 1310 indicator The 1310 indicator determines if a stable weight is obtained and the label is then applied The barcode scanner reads the barcode on the label If the data from the scanner is read correctly and agrees with the data stored then the pack continues across the out feed conveyor A second label printer located downstream from the instrument produces a duplicate label which is applied to the outer box A counter
7. ls MID Annex B Rev 2 01 April 2011 Descriptive Annex 1 INTRODUCTION This pattern of an automatic catchweighing instrument operates as an automatic weight labeller Category Y lt comprises three conveyors in feed weigh and out feed an AWTX 1310 weight indicator and a label printer The 1310 indicator is connected to a PC which provides an electronic data storage facility A second down steam label printer is also provided The instrument is designed to weigh packs statically Pack and labelling information is stored in data files selectable for the commodity and or labels being processed Labels are printed with the required transaction data and are applied to the packs automatically 2 FUNCTIONAL DESCRIPTION 2 1 Mechanical 2 1 1 The instrument comprises a supporting framework which supports the motorised weigh conveyor which comprises a conveyor mounted on to a weigh platform which incorporates the load cell s 2 1 2 The weighing module is connected to an AWTX model 1310 weight indicator Figure 1 which is connected to a PC A label printer and barcode scanner are mounted above the weighing conveyor Photocells are used to detect the pack and control the operation of the system A second label printer located downstream from the instrument applies a duplicate label to the outer box 2 2 Electrical 2 2 1 The electrical hardware is located within the 1310 indicator label printers PC and a control panel The
8. stem modified as follows The second label printer described in 2 6 1 is removed The version number for the control software described in 3 3 2 is V 1 x where Te x covers minor software variants The documentation listed in section 3 2 is modified as follows 104924 FDS V1 x Functional design specification 104924 UM V1 x Tr where x covers minor non legally relevant documentation variants 7 2 Having the documentation listed in section 3 2 modified as follows 104907 FDS V2 x Functional design specification 104415 UM V3 x where x covers minor non legally relevant documentation variants 8 ILLUSTRATIONS Figure 1 1310 indicator Figure 2 Descriptive label 6 8 9 CERTIFICATE HISTORY UK 0126 001 1 05 September 2007 Type examination certificate first issued UK 0126 0011 Rev 1 21 March 2011 Authorised alternative 7 1 added UK 0126 0011 Rev 2 06 June 2011 Authorised alternative 7 1 modified to allow version V1 x for the documentation Authorised alternative 7 2 added 7 8 Figure 1 1310 indicator Avery Weigh Tronix el Max 30 kg 220 240 SONBOHZ han 2009 18A MAX wal oc 40 C Class Y a Cen No UK 1260011 Ser eee Figure 2 Descriptive label Crown Copyright 201 1 NATIONAL MEASUREMENT OFFICE Department for Business Innovation amp Skills 8 8
Download Pdf Manuals
Related Search