TAG-IN-A-BAG™ - Manufactures
Contents
1. 3 645 6788 VISONIC LTD 1998 TAG IN A BAG DE6260U REV 0 11 98 www visonic com DE6260U 5 If you made a mistake and do not want to delete press x before pressing to cancel the operation and return the TIAB control unit to DELETE mode Pressing a second time causes the TIAB control unit to return to normal operation mode 4 Testing the TIAB e 4 6 The test mode is used for checking the TIAB keypad display elements and the internal buzzer To enter TEST mode press and hold buttons 4 and 6 simultaneously for 5 seconds Upon entering this mode the display o aE shows tS Press 0 9 successively L and then and Oo alo When pressing each button the buzzer sounds and the display shows the associated number 11 12 Once the button is pressed the display shows 88 both decimal points and all LED s light up to verify that all segments are operational and the buzzer sounds for 2 seconds The test mode will time out 10 seconds after the last button is pressed Upon exit from test mode the TIAB control unit reverts to the previous mode normal or PrN Compliance with standards Complies with Part 15 of the FCC Rules and RSS 210 of Industry and Science Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interfere2. TAG IN A BAG y po Single Door RF ID Proximity Access Control Unit 1 Introduction Thank you for choosing the TIAB Tag in a Bag programmable proximity access control unit The TIAB is designed to limit access to restricted areas while permitting authorized users to enter The unit uses state of the art proximity non contact technology The TIAB can be programmed by the installer to offer one of two security levels for opening the door 1 Valid tag only 2 Valid tag and user PIN Personal Identification Number code 2 Using the TIAB Present a valid tag 50 100 mm 2 4 in from the TIAB or from the optional external reader if installed Verify that the green LED turns on and that the door unlocks lf your TIAB is programmed to operate by tag and user s PIN code present the tag and then enter your user code The normal functions of the LEDs are summarized in the following table TABLE 1 LED functions in normal ors oe opeen oo cr eee that a valid tag was presented and the output relay was activated Indicates that invalid tag was presented or an valle PIN was entered A A Remains lit to indicate that power is on O In security level 2 blinks after the tag is accepted to prompt the user for PIN Time out A delay of more than 5 seconds between presenting a tag and starting to enter the user PIN code or between any two digits cancels the operation If you enter three consecutiv
3. d This warranty does not apply in the following cases improper installation misuse failure to follow installation and operating instructions alteration abuse accident or tampering and repair by anyone other than the Manufacturer This warranty is exclusive and expressly in lieu of all other warranties obligations or liabilities whether written oral express or implied including any warranty of merchantability or fitness for a particular purpose or otherwise In no case shall the Manufacturer be liable to anyone for any consequential or incidental damages for breach of this warranty or any other warranties whatsoever as aforesaid This warranty shall not be modified varied or extended and the Manufacturer does not authorize any person to act on its behalf in the modification variation or extension of this warranty This warranty shall apply to the Product only All products accessories or attachments of others used in conjunction with the Product including batteries shall be covered solely by their own warranty if any The Manufacturer shall not be liable for any damage or loss whatsoever whether directly indirectly incidentally consequentially or otherwise caused by the malfunction of the Product due to products accessories or attachments of others including batteries used in conjunction with the Products al Visonic Ltd VISONIC LTD ISRAEL P O B 22020 TEL AVIV 61220 ISRAEL PHONE 972 3 645 6789 FAX 972
4. e wrong codes or present an invalid tag for more than 5 seconds the TIAB control unit is disabled for 30 seconds and the buzzer beeps at a rapid rate DE6260U optional tag nec 1 SSS Lo command Push button or motion detector Figure 1 TIAB Typical Configuration Panic Output If the Panic output was connected by the installer to an alarm system or to any other external device pressing x and simultaneously causes the panic output to be activated for 5 seconds In this case the buzzer does not beep NOTE It is recommended that the user ask the installer if any advanced features were incorporated into the system in order to get proper explanations 3 Programming by the User The programming functions include adding deleting and reviewing user tags For any programming you need the Master Tag and its 4 digit PIN code Entering the Programming Mode Hold the master tag near the keyboard for at least 10 seconds After receiving an acknowledge signal from the buzzer key in your master tag PIN code 4 digits Pr Programming will blink in the display Exiting the Programming Mode Press the button to exit any of the programming mode options into the main programming mode Press the button again to quit the main programming mode and revert to normal operation Table 2 includes a summary of the user s programming functions and the following paragraphs d
5. em at least once a week For various reasons including but not limited to changes in environmental conditions electric or electronic disruptions and tampering the Product may not perform as expected The user is advised to take all necessary precautions for his her safety and the protection of his her property 6 91 MADE IN ISRAEL Appendix Users List Tag PIN Tag No code address ore 05 Tag PIN Tag me rrr address 001 Note This is a sample user list for your convenience Please copy the list as necessary 4 D6260U
6. escribe the procedures in detail TABLE 2 SUMMARY OF PROGRAMMING FUNCTIONS FUNCTION ACTION DISPLAY INDICATOR ADD Add new tags Present a tag See Section 3 1 4 Enter Pr mode and press 1 Available address blinks Green Cd Presentatag SCO Enter PIN code 4 digit Last 2 digits of PIN Available address blinks E Exit Pr mode by pressing x SHOW Review user tags 7 Press See Section 3 2 C Press Enter Pr mode and press 2 Shows address First 2 digits of PIN code Last 2 digits of PIN code Shows next address Exit Pr mode by pressing O OZ Z O O o o DELETE tags Press Enter Pr mode and press 3 Tag address stead Delete presented 4 Present the tag Tag address blinks Press S See Section 3 3 Press Blank Exit Pr mode by pressing x 2 DELETE Press Enter Pr mode and press 3 Delete lost tags 4 Enter 3 digit tag address and Tag address blinks Press S See Section 3 3 Press Tag address stead Blank Exit Pr mode by pressing x 2 Note Arrows indicate that the process can be repeated as needed 3 1 Adding User Tags Note It is recommended to maintain a list of valid tags and user names for future reference A user list form is attached to this document for your convenience Security level ie Ga
7. g mode e y ee Security level 2 Pr mode j PIN code A In programming mode Pr is displayed press 1 to select the ADD function the green LED will blink The unit will display two flashing digits the memory address available for the tag and the buzzer will beep twice Present a user tag near or on the keypad Once the tag is read by the unit the two flashing digits become steady and two short beeps sound to indicate tag reading Cd is displayed to prompt you to j enter the desired user PIN code i o within 5 seconds If the TIAB security level is 1 tag only press or wait until the tag address advances automatically If the TIAB security level is 2 tag and PIN enter the user 4 digit PIN code and press to conclude the tag adding process For security reasons 4 identical digits like 1111 are not accepted as valid PIN code D The tag adding process is completed and the TIAB reverts to the ADD mode ready for the next tag You can program up to 250 tags by repeating steps B and C above 3 2 Reviewing User Tags Pr mode Ee The holder of the master tag may review all PIN codes of the valid tags In programming mode Pr is displayed press 2 to select the SHOW function The red LED blinks and all the 250 memory addresses are scanned one by one Each address is displayed for 3 seconds a
8. nce that may cause undesired operation The Manufacturer does not represent that its Product may not be compromised and or circumvented or that the Product will prevent any death personal and or bodily injury and or damage to property resulting from burglary robbery fire or otherwise or that the Product will in all cases provide adequate warning or protection User understands that a properly installed and maintained alarm may only reduce the risk of events such as burglary robbery and fire without warning but it is not insurance or a guarantee that such will not occur or that there will be no death personal damage and or damage to property as a result The Manufacturer shall have no liability for any death personal and or bodily injury and or damage to property or other loss whether direct indirect incidental consequential or otherwise based on a claim that the Product failed to function However if the Manufacturer is held liable whether directly or indirectly for any loss or damage arising under this limited warranty or otherwise regardless of cause or origin the Manufacturer s maximum liability shall not in any case exceed the purchase price of the Product which shall be fixed as liquidated damages and not as a penalty and shall be the complete and exclusive remedy against the Manufacturer Warning The user should follow the installation and operation instructions and among other things test the Product and the whole syst
9. nd then the next address appears followed by 2 buzzer s beeps Each empty address no tag programmed blinks and each occupied address tag programmed is displayed steadily Please Note 1 Pressing while the address is displayed steadily shows the first 2 digits of the PIN code designated for that address Pressing again displays the last 2 digits of the PIN code Additional pressing expedites advance to next address 2 You may enter a 3 digit number to go directly to a specific address i e to see address 10 enter 010 3 Since the TIAB display can show 2 digits only the two decimal point LEDs assist in the numeric display of 3 digits when needed When one decimal point LED is lit the number is between 100 to 199 When two decimal point LEDs are lit the number is between 200 to 250 The following example clarifies the decimal LED function DE6260U 3 3 Deleting an Existing Tag Gas mode ee y or Pr mode eZ TAG Address Deleting a tag is possible when the tag to be deleted is available or not available lost or stolen A In programming mode Pr is displayed press 3 to select the DELETE function The yellow LED will blink and the display will be blank Present to the keypad the tag you want to delete Alternately if the tag is lost or stolen enter its 3 digit address ins
10. tead and press The address will flash in the display Press again to approve the tag s deletion The display will stop flashing Press once more to confirm The TIAB sounds 3 short beeps to indicate that the tag is deleted The display blanks out ready to delete another tag Notes 1 In the DELETE mode the TIAB control unit searches automatically through addresses 001 to 250 does not search address 000 2 Tag deletion deletes tag information and the 4 digit PIN code 3 Deletion of address 000 causes the TIAB control unit to return to the ADD mode A new master tag and PIN code must be entered for further use 4 Deleting ALL codes except the master code is accomplished by entering address 999 WARRANTY Visonic Ltd and or its subsidiaries and its affiliates the Manufacturer warrants its products hereinafter referred to as the Product or Products to be in conformance with its own plans and specifications and to be free of defects in materials and workmanship under normal use and service for a period of twelve months from the date of shipment by the Manufacturer The Manufacturer s obligations shall be limited within the warranty period at its option to repair or replace the product or any part thereof The Manufacturer shall not be responsible for dismantling and or reinstallation charges To exercise the warranty the product must be returned to the Manufacturer freight prepaid and insure
Download Pdf Manuals
Related Search