Home

ADE-2100 1st Manual

1. ADE 2100 VIA V4 Bus Eden CX700M 3 5 ESB User s Manual Rev 1 0 2007 01 03 P N 600C002210010 ADE 2100 User s Manual Copyright All rights reserved The information contained in this guide has been validated and reviewed for accuracy No patent liability is assumed with respect to the use of the information contained herein While every precaution has been taken in the preparation of this guide the Manufacturer assumes no responsibility for errors or omissions No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Manufacturer Trademark Intel Pentium and Celeron are registered trademarks of Intel Corporation Microsoft and Windows are registered trademarks of Microsoft Corporation All products and company names are trademarks or registered trademarks of their respective holders These specifications are subject to change without notice Technical Support We hope you to get the maximum performance from your products and be willing to help if running into technical difficulties For the most frequently asked questions it s easily found answers from the product documentation and usually a lot more detailed so please take reference to this manual first If the answer still can not be found gather all the information or questio
2. Tle lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Ualues F6 Fail Safe Defaults F Optimized Defaults 4 2 5 10 1 PowerOn by PCI Card Enables activity detected from any PCI card to power up the system or resume from a suspended state Such PCI cards include LAN onboard USB ports etc The options Disabled Enabled 4 2 5 10 2 Modem Ring Resume Enables any Ring In signals from the modem to restore the system from a suspended state to an active state The options Disabled Enabled 4 2 5 10 3 RTC Alarm Resume Sets a scheduled time and or date to automatically power on the system The options Disabled Enabled 42 50 ADE 2100 User s Manual 4 2 6 PnP PCI Configurations Phoenix AwardBIOS CMOS Setup Utility 1 PnP PCI Configurations PNP 05 Installed No Item Help Reset Configuration Data Disabled Menu Level b Resources Controlled Buy Auto ES5CD 1 IRQ Resources Press Enter Select Yes if you are using a Plug and Play PCI UG Palette Snoop Disabled capable operating Assign IRQ For UGA Enabled system Select No if Assign IRQ For USB Enabled you need the BIOS to conf igure non boot xx PCI Express relative items se devices Maximum ASPM supported LOs amp L1 Maximum Payload Size 4096 Tle lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults 4 2 6 1 PNP OS Instal
3. EN MUN 1 DATA 4 DATA 44 5V 2 18 50 USB 1 2 3 4 PIN No Note This mainboard provides 1 USB header on the board allowing for 2 additional USB ports To make use of these headers you must attach a USB bracket cable with USB ports some models will come packaged with a USB 4 port bracket cable The optionally packaged bracket will have two connectors that you can connect to the headers CN16 The other end bracket containing the USB ports is attached to the computer casing If you are using a USB 2 0 device with Windows 2000 XP you will need to install the USB 2 0 driver from the Microsoft amp website If you are using Service pack 1 or later for Windows XP and using Service pack4 or later for Windows 2000 you will not have to install the driver ADE 2100 User s Manual 2 3 13 CD In from CD ROM CN8 2 3 14 LCD Inverter Connector CN9 PIN Description PINNo Description Ground 2 1438V CD Ground 2 3 15 LVDS Connector CN10 E IEIEINE BDATM 6 5 A DATAH DVI TDCO B DATM 8 7 A DATATs DVI_TDCO gt BDATM 10 9 ADATA2 DVITDCT a A DATA3 LDDC DATA L DVI DATA Signa Type peserpion LDDC CLKL EDID support for flat panel display LDDC DATAL EDID support for flat panel display DVI TCL4 DVI Clock Output These pins provide the differential clock outputs to at the DVI interface corresponding a data on TDC 0 2 outputs DVI Data Channel 0
4. Enabled Quick Power On Self Test Enabled First Boot Device Hard Disk Second Boot Device CDROM Third Boot Device L51201 Boot Other Device Enabled Onboard Lan Boot ROM Disabled Boot Up NumLock Status 0n Typematic Rate Setting Disabled Tupematic Rate Chars Sec 6 Tupematic Delay Msec 250 Security Option Setup MPS Version Control For 05 1 41 05 Select For DRAM gt 64MB Non 032 1 Video BIOS Shadow Enabled Tle lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults 4 2 2 1 CPU Feature Phoenix AwardBIOS CMOS Setup Utility CPU Feature Delay Prior to Thermal 16 Min Item Help Thermal Monitor 11 Thermal Management x TMZ Bus Ratio 4 X Menu Level gt gt x TM2 Bus UID Tle lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults 4 2 2 1 1 Delay Prior to Thermal Select this item allows the delay prior to thermal time The Choice Auto 4 8 16 32Min 27 50 ADE 2100 User s Manual 4 2 2 1 2 Thermal Management It allows you to select the thermal Monitor 4 2 2 2 Hard Disk Boot Priority Press Enter and It shows Bootable add in Card m i Phoenix AwardBIOS CMOS Setup Utility gt E Hard Disk Boot Priority 1 Bootable fidd in Cards Item Help Menu Level gt gt Use lt f gt or 1 to select a device then p
5. 3U 3 36V 12 0U 12 28V UBRT U 2 94V Tlee Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults 44 50 ADE 2100 User s Manual 4 2 8 Frequency Voltage Control o E Phoenix AwardBIOS CMOS Setup Utility Frequency Voltage Control CPU Clock Ratio 10 X1 Item Help 0 2071 Spread Spectrum CPU Host AGP PCI Clock Default Menu Level gt Tle lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults 4 2 8 1 CPU Clock Ratio This item allows you to set up the CPU clock ratio but this function depends on different CPU performance ltis only effective for those clock ratio haven t been locked 4 2 8 2 Spread Spectrum This is to adjust extreme value of the pulse for EMI test 4 2 8 3 CPU Host AGP PCI Clock This item allows you to select CPU Host AGP PCI Clock 45 50 ADE 2100 User s Manual 4 2 9 Load Fail Safe Default Use this menu to load the BIOS default values for the minimal stable performance for your system to operate Press Y to load the BIOS default values for the most stable minimal performance System operations Phoenix AwardBIOS CMOS Setup Utility Load Fail Safe Defaults Load Fail Safe Defaults V N N Esc Quit F9 Menu in BIOS F10 Save 8 Exit Setup 46 50 ADE 2100 User s Manual 4 2 10 Loa
6. 5 ESB To install your ADE 2100 into standard chassis or proprietary environment you need to perform the following steps 1 Check all jumpers setting on proper position 2 Place ADE 2100 into the dedicated position in your system 3 Attach cables to existing peripheral devices and secure it WARNING Please ensure that your ESB properly inserted and fixed by mechanism Otherwise the system might be unstable or do not work from bad contact of golden finger 3 2 1 Dual VIA VT6106S Ethernet Controllers The ADE 2100 provides two LED indicators on RJ 45 connectors to show LAN interface status These messages will give you a guide for troubleshooting Yellow LED indicates transmit and receive activity Blinking indicates transmit receive activity On indicates no activity but link is valid Off link is invalid Green LED indicates Link speed On link speed at 100Mbps Off link speed at 10Mbps 3 2 2 Drivers Support ADE 2100 provides on CD Title to support on board VGA and Ethernet device drivers in various operating systems Before installing the device drivers please see the reference files in each sub directory 23 50 O CHAPTER 4 ADE 2100 User s Manual 4 BIOS Setup 4 1 Entering Setup Phoenix Award BIOS has a built in setup program that allows users to modify the basic system configuration This information is stored in CMOS RAM whose power is supplied by a battery so that it can retain the setup information even when the power is tu
7. Audio Connector CNI zeolit 17 2 3 10 COM VGA Connector CN4 nee 18 2 3 11 LAN 1 2 8 USB 1 2 3 4 Connectors CN5 CN6 pp 18 2 3 12 Internal USB 5 6 Connectors CN16 pp 18 2 9 13 OD In from CD ROM CN8 tiitenis ct Reano E o Ipod eps aH RDUM octane eames 19 2 3 14 LCD Inverter Connector CN9 pp 19 2 3 15 LVDS Connector CN10 pp 19 2 3 16 Serial Port 2 Connector CN1T2 oer ne rne e dne o tatnen n Leute enun 20 2 3 17 Front Panel Connector CN 13 pp 20 2 3 18 System Fan Connectors CN14 pp 20 2 3 19 Serial ATA 1 2 Connectors SATA1 SATA2 pp 20 4 50 3 1 3 2 4 1 4 2 ADE 2100 User s Manual crit m X 0 A A A A A A O 22 Main METAOVY M T 22 Installing the 3 5 ESB ussscnatapasaicida inda kava a 23 3 4 1 Dual VIA VT6106S Ethernet Controllers sees 23 34 2 Drivers SUIT aspe n qux e r 23 BIOS SQ UD T E Ooa 25 cei 25 M n Menusi eea a i Guan otok 25 4 2 1 Standard CMOS Features 4 26 4 2 2 Advanced BIOS Features pp 27 4 2 8 Advanced Chipset Features pp 31 428 Integrated Pephietalus eite ia ie qr Dee e aeu Du Caco De aus inu Dex en eren Suis 35 4 2 5 Power Management Setup pp 40 42 5 PnP PCI Configurations uoces s du sadenia da ono dania 43 4227 PG Heal
8. F6 Fail Safe Defaults F Optimized Defaults 4 2 3 3 1 PCI Master 0 WS Write This BIOS feature determines whether the chipset inserts a delay before any writes from the PCI bus The choice Enabled Disabled 4 2 3 3 2 PCI Delay Transaction The chipset has an embedded 32 bit posted write buffer to support delay transactions cycles Select Enabled to support compliance with PCI specification version 2 1 The choice Enabled Disabled 4 2 3 3 3DRDY Timing Allow you to set DRDY Timing The choice Slowest Default Optimize 34 50 ADE 2100 User s Manual 4 2 4 Integrated Peripheral Phoenix fiuardBIOS CMOS Setup Utilitu Integrated Peripherals gt VIA OnChip IDE Device Press Enter Item Help gt VIA OnChip PCI Device Press Enter gt SuperIO Device Press Enter Menu Level gt gt USB Device Setting Press Enter Tle lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults 4 2 4 1 VIA OnChip IDE Device Phoenix AwardBIOS CMOS Setup Utility VIA OnChip IDE Device SATA Controller Enabled Item Help IDE DMA transfer access Enabled OnChip IDE Channeli Enabled Menu Level b IDE Prefetch Mode Enabled Secondary Master PIO Auto Secondary Slave PIO Auto Secondary Master UDMA Auto Secondary Slave UDMA Auto IDE HDD Block Mode Enabled Tle lt Move Enter Select PU PD Value F10 Save ESC E
9. Ibs 0 2 Kg 11 50 ADE 2100 User s Manual 1 4 System Architecture All of details operating relations are shown in ADE 2100 system block diagram VIA V4 Eden 1 GHz Processor V4 BUS 1 Dual channel SDVO BUS 400 533 MHz H i n DVI 24 bitLVDS o 200 pin DDR2 SODIMM USB V2 0 USB1 USB2 USB3 ae T 2 ports 2 ports 2 ports In one Chipset One IDE Channel PCI Bus CF 43 44 pin 1DE 4 JM m Up to UATA33 Mic in E Line in AC97 Lin e Realteck e out 4 LPC BUS a ALC833 Spin BW 150MB s VIA VIA VT6106S VT6106S Super I O Ethernet Ethernet W83697HG 7 pin SATA 1 USB LAN USB LAN 7 pin SATA 2 RJ45 RJ45 COM1 COM2 RS 232 reese 422 485 12 50 ADE 2100 User s Manual imensions D 1 5 41 99 137 16 125 73 116 93 o o9 8 88 9 08 0043 320 5 00 60 05 AT 93 84 97 54 98 40 mm Unit 13 50 O CHAPTER 2 ADE 2100 User s Manual 2 Hardware Configuration Setting This chapter gives the definitions and shows the positions of jumpers headers and connectors All of the configuration jumpers on ADE 2100 are in the proper position The default settings shipped from factory are marked with an asteris
10. Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults 4 2 3 2 1 AGP Aperture Size This field determines the effective size of the Graphic Aperture used for a particular GMCH configuration It can be updated by the GMCH specific BIOS configuration sequence before the PCI standard bus enumeration sequence takes place If it is not updated then a default value will select an aperture of maximum size 4 2 3 2 2 AGP 2 0 Mode This item allows you to select AGP bus support 8x or x4 4 2 3 2 3 AGP Driving Control This BIOS feature allows you to set whether the AGP controller should dynamically adjust the AGP driving strength or allow manual configuration by the BIOS 32 50 ADE 2100 User s Manual 4 2 3 2 4 AGP Driving Value This BIOS feature will only be activated if you set the AGP Driving Control BIOS feature to Manual It determines the overall drive strength of the AGP bus 4 2 3 2 5 AGP Fast Write This BIOS feature controls the AGP bus Fast Write capability Fast Write is a feature which accelerates memory write transactions from the chipset to the AGP device 4 2 3 2 6 AGP Master 1 WS Write This BIOS feature allows you to reduce the time the AGP bus mastering device has to wait before it can initiate a read command to only one wait state This speeds up all reads that the AGP bus master makes from the system memory 4 2 3 2 7 AGP Master 1 WS Read This BIOS feature allows you to reduce
11. Serial Bus USB controller and you have a USB mouse The choice Enabled Disabled 4 2 4 4 5USB Storage Function This field allows you to support USB storage on DOS 39 50 ADE 2100 User s Manual 4 2 5h Power Management Setup h Phoenix fiuardBIOS CMOS Setup Utility 1 Power Management Setup ACPI function Enabled Item Help Power Management Option User Def ine HDD Power Down Disable Menu Level gt Suspend Mode Disable Video Off Option Suspend gt Off Video Off Method U H SYNC Blank l MODEM Use IRQ 31 Soft ff by PURBTN CInstant Off 1 PWRON After PWR Fail Former Sts 1 gt Wakeup Event Detect Press Enter Tle lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults 4 2 5 1 ACPI Function This item allows you to enable disable the Advanced Configuration and Power Management ACPI The choice Enabled Disabled 4 2 5 2 Power Management This category allows you to select the type or degree of power saving and is directly related to the following modes 1 HDD Power Down 2 Doze Mode 3 Suspend Mode 4 2 5 3 HDD Power Down When Enabled and after the set time of system inactivity the hard disk drive will be powered down while all other devices remain active The choice Disabled 1 15Min 4 2 5 4 Suspend Mode When Enabled and after the set time of system inactivity All devices except the CPU
12. will be shut off The choice Disabled 1 2 4 8 12 20 30 40 Min and 1Hour 40 50 ADE 2100 User s Manual 4 2 5 5 Video Off Option This option defines the level of power saving mode requires in to power down the video display As a default the video powers down both in suspend mode and standby mode 4 2 5 6 Video Off Method This determines the manner in which the monitor is blanked V H SYNC Blank This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer Blank Screen This option only writes blanks to the video buffer DPMS Initial display power management signaling 4 2 5 7 MODEM Use IRQ This determines the IRQ in which the MODEM can use The choice 3 4 5 7 9 10 11 and NA 4 2 5 8 Sort Off by PWRBTN Pressing the power button for more than 4 seconds Instant Off forces the system to enter the Soft Off state when the system has hung Only could working on ATX Power supply 4 2 5 9 PWRON After PWR Fail This item allows you to select if you want to power on the system after power failure The choice Off On and Former Sts 41 50 ADE 2100 User s Manual 4 2 5 10 Wakeup Event Detect Phoenix AwardBIOS CMOS Setup Utility Wakeup Event Detect PowerOn by PCI Card By 031 Item Help Modem Ring Resume By 031 RTC Alarm Resume Disabled Menu Level gt gt x Date Cof Month x Resume Time hh mm ss 0 9
13. year and century gt IDE Secondary Slave Video EGA UGA Halt On All But Keyboard Base Memory 640K Extended Memory 15360K Total Memory 16384K Tle Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults 4 2 1 1 Date mm date year and Time hh mm ss Set the system date and time Note that the Day automatically changes when you set the date 4 2 1 2 IDE Primary Secondary Master Slave Press Enter to enter the sub menu of detailed options Described in IDE Adapters 4 2 1 3 Video Select the default video device The Choice EGA VGA CGA 40 CGA 80 MONO EGA VGA CGA 40 CGA 80 and MONO 4 2 1 4 Halt On Select the situation in which you want the BIOS to stop the POST process and notify you The Choice All Errors No Errors All but Keyboard All but Diskette All but Disk Key 4 2 1 5 Base Memory Displays the amount of conventional memory detected during boot up 4 2 1 6 Extended Memory Displays the amount of extended memory detected during boot up 4 2 1 7 Total Memory Displays the total memory available in the system 26 50 ADE 2100 User s Manual 4 2 2 Advanced BIOS Features Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Features gt CPU Feature Press Enter Item Help gt Hard Disk Boot Priority Press Enter Virus Warning Disabled Menu Level gt CPU L1 amp L2 Cache Enabled CPU L2 Cache ECC Checking
14. 2 Exit Selection Save CMOS value changes to CMOS and exit setup Enter lt Y gt to store the selection made in the menus in CMOS a special section in memory that stays on after turning the system off The BIOS configures the system according to the Setup selection stored in CMOS when boot the computer next time The system is restarted after saving the values Phoenix AwardBIOS CHOS Setup Utility Standard CHOS Features Freguency Voltage Control Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Load Fail Safe Defaults Load Optimized Defaults Set Supervisor Password Power Management PnP PCI Configura PC Health Status Esc Quit F9 Menu in BIOS Select Item F10 Save amp Exit Setup Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Frequency Voltage Control Load Fail Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management S PnP PCI Configurat PC Health Status Esc Quit F9 Menu in BIOS Select Item F10 Save amp Exit Setup Abandon all Data 49 50 ADE 2100 User s Manual 50 50
15. B 1 1 one 6 pin Mini DIN connector for PS 2 mouse and keyboard and one 12 V 4 pin DC in power connector designed to support ATX power function Targeted for key embedded applications such as Point of Sales POS car media centers industrial PCs IPC and ultra compact low power desktop systems such as thin clients that require flat panels support the digital display using LVDS DVI interface All of these features make ADE 2100 excellent in all in one applications 8 50 ADE 2100 User s Manual 1 2 Packing Check List The ADE 2100 package includes the following basic items accompany with this manual One 3 5 ADE 2100 ESB One Quick Installation Guide for ADE 2100 One 44 pin IDE cable One Serial ATA cable One Serial port cable for COM2 One 12 V Power cable One Y cable for PS 2 keyboard amp mouse One Supporting CD ROM contains User s Manual and internal VGA display driver and VIA VT6106S Ethernet network controller driver and on board devices drivers V V VV ON NON Vv If any of these items is damaged or missed please contact your vendor and save all packing materials for future replacement and maintenance 9 50 1 3 Specifications System CPU FSB BIOS System Chipset I O Chip System Memory Storage SSD Watchdog Timer H W Status Monitor MIO Internal External Display Chipset Display Memory Resolution VGA LCD Interface LVDS DVI Audio HDAC Audio Interface ADE 2100 User s Manual
16. Bank Inter leave Disabled Precharge to Active Trp 4T Active to Precharge Tras O T Active to CMD Trcd 4T REF to ACT REF Trfc 25T ACT O to ACT 1 CTRRD aT Read to Precharge Trtp 2T Write to Read CMD Twtr 1T 2T Write Recovery Time Twr 4T DRAM Command Rate ZT Command 1 RDSAIT mode Auto RDSAIT selection 93 Tle lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults 31 50 ADE 2100 User s Manual 4 2 3 1 1 DRAM Clock This item determines DRAM clock using SPD or manual configuration Make sure your memory module has SPD Serial Presence Data if you want to select the By SPD option Options Manual By SPD default 4 2 3 1 2DRAM Timing Select the operating system that is selecting DRAM timing so select SPD for setting SDRAM timing by SPD The choice Manual By SPD 4 2 3 2 AGP amp P2P Bridge Control Phoenix AwardBIOS CMOS Setup Utility AGP amp PZP Bridge Control AGP Aperture Size 128M AGP 2 0 Mode 8X1 AGP Driving Control Auto Menu Level gt gt x AGP Driving Value DA AGP Fast Write Disabled AGP Master 1 WS Write Enabled AGP Master 1 WS Read Enabled AGP 3 0 Calibration cycle Enabled UGA Share Memory Size 64M Direct Frame Buffer Enabled Panel Type 800x600 18bits ich Outport Port DIO Dithering Disabled Tle lt Move Enter Select PU PD Value F10
17. Output These pins provide the DVI differential A S output for data channel 0 Blue 2 DVI Data Channel 1 Output These pins provide the DVI differential PA TIBI rem output for data channel 1 Green DVI Data Channel 2 Output These pins provide the DVI differential PYLE o output for data channel 2 Red Serial Port SMBus Clock and Data The SPCLK signals are the DVI_CLK clocks for serial data transfer The SPD signals are the data signals DVI_DATA used for serial data transfer SPCLK1 SPD1 is typically used for DVI monitor communications 19 50 ADE 2100 User s Manual 2 3 16 Serial Port 2 Connector CN12 2 3 17 Front Panel Connector CN13 Buzzer Signal Description System Power On LED PINNo Signal Description 8 RI Ground 9 19 Gud Note The enclosed serial port cable for COM2 with IDE1 Active LED different functions as below PIN No Signal Description m 4 5V Pull up for HDD LED re Ty 6 HDD actives LED cathode terminal A CA CET RS 232 I System Power On Switch will 85322 PINNo Signal Description Power button control signal 9 Ground System Reset PINNo Signal Description HESSEN Reset Ground 2 3 18 System Fan Connectors CN14 2 3 19 Serial ATA 1 2 Connectors SATA1 SATA2 PINNo Description These SATA connectors support Serial ATA 150 Each SATA connector can only support one serial ATA device Fan Speed Cont
18. Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults 4 2 4 3 1 Onboard Serial Port 1 2 Select an address and corresponding interrupt for the first and second serial ports The choice 3F8 IRQ4 2E8 IRQ3 3E8 IRQ4 2F8 IRQ3 Disabled and Auto 38 50 ADE 2100 User s Manual 4 2 4 4 USB Device Setting Phoenix AwardBIOS CMOS Setup Utility USB Device Setting 1 0 Controller Enabled 1 2 0 Controller Enabled Operation Mode High Speed Menu Level gt gt Keyboard Function Enabled Mouse Function Enabled Enable or Disable Storage Function Enabled Universal Host Controller USB Mass Storage Device Boot Setting ex Interfacefor Universal Serial Bus Tle lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults 4 2 4 4 1 USB 1 0 2 0 Controller Select Enabled if your system contains a Universal Serial Bus 2 0 USB 2 0 controller and you have USB peripherals The choice Enabled Disabled 4 2 4 4 2 USB Operation Mode This field allows you to set the operation mode of the USB port 4 2 4 4 3USB Keyboard Function Select Enabled if your system contains a Universal Serial Bus USB controller and you have a USB keyboard The choice Enabled Disabled 4 2 4 4 4USB Mouse Function Select Enabled if your system contains a Universal
19. VIA V4 Bus Eden 1 GHz processor 400 MHz Award BIOS with 4 Mb Flash ROM VIA CX700M Winbond W83697HG l O controller 1 x 200 pin SO DIMM socket support DDR2 400 533 SDRAM Max up to 1 GB memory 1 x Parallel ATA IDE port with UDMA 33 support by 44 pin IDE connector 2 x Serial ATA 150 ports 1 x CompactFlash socket with ejector at I O side shared Master IDE Reset 1 sec 255 min and 1 sec or 1 min step Monitoring system temperature voltage and cooling fan status 1 x RS 232 422 485 2 x USB 2 0 1 x VGA 1 x Audio jack 2 x RJ 45 1 x RS 232 4 x USB 2 0 1x KB amp Mouse VIA CX700M Up to 128 MB shared memory CRT 2048 x 1536 Panel 1600 x 1200 DVI 1600 x 1200 DSUB 15 connector for VGA output 1 x dual channel or 2 x single channel with 24 bit LVDS 1 x 30 pin DVI shared with LVDS interface Realtek ALC883 7 1 2CH audio codec Mic in Line in Line out CD in pin header 10 50 ADE 2100 User s Manual Ethernet Chipset Dual VIA VT6106S Ethernet controllers Ethernet Interface IEEE 802 3 10BASE T 100BASE TX Mechanical amp Environmental Power Requirement 12 V 0 78 A with onboard VIA V4 Bus 1 GHz amp 1 GB DDR2 SDRAM Power Type DC in 12 V 4 pin power connector ATX function Operating Temperature 0 60 C 32 140 F Operating Humidity 096 9096 relative humidity non condensing Size L x W 5 7 x 4 144 78 mm x 101 6 mm Weight 0 44
20. ating system from the devices in the sequence selected in these items The Choice Floppy LS ZIP HDD SCSI CDROM LAN and Disabled 4 2 2 8 Onboard Lan Boot ROM This item allows you to enable or disable the onboard LAN Boot ROM The choice Enabled Disabled 4 2 2 9 Boot Up NumLock Status Select power on state for NumLock The choice On Off 4 2 2 10 Typematic Rate Setting Keystrokes repeat at a rate determined by the keyboard controller When enabled the typematic rate and typematic delay can be selected The choice Enabled Disabled 4 2 2 11 Typematic Rate Chars Sec Sets the number of times a second to repeat a keystroke when you hold the key down The choice 6 8 10 12 15 20 24 and 30 4 2 2 12 Typematic Delay Msec Sets the delay time after the key is held down before it begins to repeat the keystroke The choice 250 500 750 and 1000 4 2 2 13 Security Option Select whether the password is required every time the system boots or only when you enter setup System The system will not boot and access to Setup will be denied if the correct password is not entered at the prompt Setup The system will boot but access to Setup will be denied if the correct password is not entered at the prompt Note To disable security select PASSWORD SETTING at Main Menu and then you will be asked to enter password Do not type anything and just press Enter it will disable security Once the security is disable
21. d the system will boot and you can enter Setup freely 4 2 2 14 MPS Version Control for OS Select the operating system that is Multi Processors Version Control for OS The choice 1 4 1 1 29 50 ADE 2100 User s Manual 4 2 2 15 OS Select For DRAM 64MB Select the operating system that is running with greater than 64MB of RAM on the system The choice Non OS2 OS2 4 2 2 16 Video BIOS Shadow Turns on BIOS ROM shadowing for the block of memory normally used for standard VGA video ROM code In short it speeds up your system by copying the contents of your video BIOS code from the slow ROM in which it resides into faster RAM 30 50 ADE 2100 User s Manual 4 2 3 Advanced Chipset Features Phoenix fiuardBIOS CMOS Setup Utilitu Advanced Chipset Features gt DRAM Clock Drive Control Press Enter Item Help gt AGP amp PZP Bridge Control Press Enter gt CPU amp PCI Bus Control Press Enter Menu Level gt System BIOS Cacheable Enabled Video RAM Cacheable Disabled Init Display First PCI Slot Tle lt Move Enter Select PU PD Value F10 Save ESC Exit F1i General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults 4 2 3 1 DRAM Clock Drive Control Phoenix AwardBIOS CMOS Setup Utility DR M Clock Drive Control Current FSB Frequency Item Help Current DRAM Frequency DRAM Clock By SPD Menu Level gt gt DRAM Timing Auto By SPD SDRAM CAS Latency DDR DDR 2 5 7 4
22. d Optimized Defaults Use this menu to load the BIOS default values that are factory settings for optimal performance system operations While Award has designed the custom BIOS to maximize performance the factory has the right to change these defaults to meet their needs Press lt Y gt to load the default values setting for optimal performance system operations Phoenix AwardBLOS CMOS Setup Utility Standard CMOS Features Frequency Voltage Control Load Fail Safe Defaults Load Optimized Defaults Set Supervisor Password Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management PnP PCI Configura PC Health Status Esc Quit F9 Menu in BIOS F10 Save amp Exit Setup 4 2 11 Supervisor User Password Setting You can set either supervisor or user password or both of them Supervisor Password able to enter change the options of setup menus Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP PCI Configurati PC Health Status Advanced Chipset Features Esc Quit F9 Menu in BIOS F10 Save amp Exit Setup Change Set Disable Password Freguency Voltage Control Load Fail Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Setup t Saving Select Item ADE 2100 User s Manual User Password able to enter but no right to c
23. hange the options of setup menus Phoenix AwardBIOS CMOS Setup Utility Set User Password t Enter Password u Esc Quit F9 Menu in BIOS Select Item F10 Save amp Exit Setup Type the password up to eight characters in length and press Enter The password typed now will clear any previously entered password from CMOS memory You will be asked to confirm the password Type the password again and press Enter You may also press Esc to abort the selection and not enter a password To disable a password just press Enter when you are prompted to enter the password A message will confirm the password will be disabled Once the password is disabled the system will boot and you can enter Setup freely PASSWORD DISABLED When a password has been enabled you will be prompted to enter it every time you try to enter Setup This prevents an unauthorized person from changing any part of your system configuration Additionally when a password is enabled you can also require the BIOS to request a password every time your system is rebooted This would prevent unauthorized use of your computer You determine when the password is required within the BIOS Features Setup Menu and its Security option If the Security option is set to System the password will be required both at boot and at entry to Setup If set to Setup prompting only occurs when trying to enter Setup 48 50 ADE 2100 User s Manual 4 2 1
24. ion describes how to properly mount the CPU main memory and M System Flash disk for a safe installation It will also introduce and show you the driver installation procedure for the Graphics Controller and Ethernet Controller Chapter 4 BIOS Setup Information specifies the meaning of each setup parameter how to get advanced BIOS performance and update to a new BIOS 3 50 1 1 1 2 1 3 1 4 1 5 2 1 2 2 2 3 ADE 2100 User s Manual Table of Content ee 8 Descriptigm uae corii ria suce cuna Ciara rk v V a E E E uu 8 Packing Check EISE aede nici cd ocn cU Kd Rad Du cda ndun a dw d 9 Specifications osa a ARR AUDI QUE r i 10 System Architeclure iu assises sasxa sna p ka aa 12 DIMENSIONS q 13 Hardware Configuration Setllng s i s suski dosasi k inu os dka 15 Board LAYOUT 15 Jumpers amp Connectors s uva z cs ooo k o k ENG IGI UE 16 J mpers Conneetors Setting usas s nka k n aa 17 2 3 1 RTGCMOS Clear Select 1 17 2 3 2 COM2 RS 232 422 485 Select JP2 ccceceeeeeeeeeeeeeecceeeeeeeeeeeesneeeeeeeeeees 17 2 3 8 BIOS Write Protect JP3 nnne 17 2 3 4 AT ATX Power Select CIPS eee ient duna ast on salda 17 2 3 5 PS 2 Keyboard amp Mouse ONT iuto poslbsictn ten absol 17 2 3 6 Power Connector CN2 pp 17 2 3 7 ATX Power Connector CN7 eene nnne 17 2 3 8 X Auxiliary Power Connector 2 CNT9 pp 17 23 9
25. k In general jumpers on the 3 5 ESB are used to select options for certain features Some of the jumpers are designed to be user configurable allowing for system enhancement The others are for testing purpose only and should not be altered To select any option cover the jumper cap over SHORT or remove NC it from the jumper pins according to the following instructions Here NC stands for Not Connect 2 1 Board Layout DIMM1 Rear side m 2 S Oo C oooco Qo 2 es 90 U15 gt Rear side CN14 Win 557 00000 oo Oe C ooooo IXDooooo 00 JP2 OOOOO0O0OO0O0O00DOOOOO0COOO NOOOOO0OOO0O0O0DOOOOOCCOOO DO OOD 15 50 ADE 2100 User s Manual 2 2 Jumpers amp Connectors JUMPERS FUNCTION REMARK JP1 RTC CMOS clear select 1 x 3 header JP2 COM2 RS 232 422 485 select 2 x 7 header JP3 BIOS write protect 1 x 3 header JP4 AT ATX power select 1 x 2 header CONNECTORS FUNCTION REMARK CN1 PS 2 keyboard amp mouse connector CN2 Power connector 1 x 3 wafer CN3 Audio connector CN4 D sub 15 pin VGA amp D sub 9 pin serial port 1 connectors CN5 USB 1 2 amp LAN 1 connectors CN6 USB 3 4 amp LAN 2 connectors CN7 ATX power connector CN8 CD In from CD ROM 1 x 4 header CN9 LCD inverter connector 1 x 5 wafer CN10 LVDS DVI connector HIROSE CN11 Primary IDE connector 2 x 22 box header CN12 Serial port 2 connector 2 x 7 header CN13 Front panel connector 2 x 5 header CN14 System fan connector 1 x 3
26. led Select Yes if you are using a Plug and Play capable operating system Select No if you need the BIOS to configure no Boot device 4 2 6 2 Reset Configuration Data Normally you leave this field Disabled Select Enabled to reset Extended System Configuration Data ESCD when you exit Setup if you have installed a new add on and the system reconfiguration has caused such a serious conflict that the operating system cannot boot 4 2 6 3 Resources Controlled By The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug and Play compatible devices However this capability means absolutely nothing unless you are using a Plug and Play operating system such as Windows 95 If you set this field to manual choose specific resources by going into each of the sub menu that follows this field 4 2 6 4 PCI VGA Palette Snoop This function determines if the graphics card should allow VGA palette snooping by a fixed function display card It is only useful if a fixed function display card using that requires a VGA compatible graphics card to be present Otherwise leave the setting as default Disabled 43 50 ADE 2100 User s Manual 4 2 6 5 Assign IRQ For VGA USB Assign IRQ for VGA and USB devices The options Disabled Enabled 4 2 7 PC Health Status Phoenix AwardBIOS CMOS Setup Utility PC Health Status CPU Temperture 2931 B6 F System FAN Speed 3443 RPM Menu Level gt Ucore 1 32VY 3
27. ns applying to the problem and with the product on hand contact your distributor sales representative or customer service center for technical support Most problems reported are minor and able to be easily solved over the phone In addition free technical support is available and always ready to give advices on application requirements or specific information on the installation and operation of any of our products Please have the following information ready before you call 1 Product name and serial number Description of your peripheral attachments Description of your software operating system version application software etc A complete description of the problem The exact wording of any error messages E E a o 2 50 ADE 2100 User s Manual How to Use This Manual This manual is written for the system integrator PC technician and knowledgeable PC end user It describes how to configure your ADE 2100 to meet various operating requirements The user s manual is divided into four chapters with each chapter addressing a basic concept and operation of the server board Chapter 1 Introduction presents what you have inside the box and gives you an overview of the product specifications and basic system architecture for the ADE 2100 server board Chapter 2 Hardware Configuration Setting shows the definitions and locations of Jumpers and Connectors so that you can easily configure your system Chapter 3 System Installat
28. ress lt gt to move it up or lt gt to move it down the list Press lt ESC gt to exit this menu Tle lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults 4 2 2 3 Virus Warning Allow you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection If this function is enabled and someone attempts to write data into this area BIOS will show a warning message on screen and alarm beep Enabled Activates automatically when the system boots up causing a warning message to appear when anything attempts to access the boot sector or hard disk partition table Disabled No warning message will appear when anything attempts to access the boot sector or hard disk partition table 4 2 2 4 CPU L1 amp L2 Cache These two categories speed up memory access However it depends on CPU chipset design Enabled Enable cache Disabled Disable cache 4 2 2 5 CPUL2 Cache ECC Checking This item allows you to enable disable CPU L2 Cache ECC checking The choice Enabled Disabled 28 50 ADE 2100 User s Manual 4 2 2 6 Quick Power On Self Test This category speeds up Power On Self Test POST after you power up the computer If itis set to Enable BIOS will shorten or skip some check items during POST Enabled Enable quick POST Disabled Normal POST 4 2 2 7 First Second Third Boot Device The BIOS attempts to load the oper
29. rned off Press Delete when you Power on or Reboot the computer system i e After the logo appears at the center of the screen please press Delete to enter the BIOS setup program In the BIOS make sure that everything is working fine before you try to optimize it for maximum performance 4 2 Main Menu Phoenix AwardBIOS CMOS Setup Utility gt Standard CMOS Features gt Frequency Voltage Control gt Advanced BIOS Features Load Fail Safe Defaults gt Advanced Chipset Features Load Optimized Defaults gt Integrated Peripherals Set Supervisor Password gt Power Management Setup Set User Password gt PnP PCI Configurations Save amp Exit Setup gt PC Health Status Exit Without Saving Esc Quit F9 Menu in BIOS T gt lt Select Item F10 Save amp Exit Setup Time Date Hard Disk Type When you enter the PHOENIX AWARD CMOS Setup Utility the Main will appear on the screen The Main allows you to select several configuration options Use the left right arrow keys to highlight a particular configuration screen from the top menu bar or use the down arrow key to access and configure the information below 25 50 ADE 2100 User s Manual 4 2 1 Standard CMOS Features Phoenix fiuardBIOS CMOS Setup Utility Standard CMOS Features Date mm dd uu Item Help Time hh mm ss Menu Level gt gt IDE Primary Master gt IDE Primary Slave Change the day month gt IDE Secondary Master
30. rol Note With most storage devices there is a power cable that you need attach to a power source power supply 20 50 O CHAPTER 3 ADE 2100 User s Manual 3 System Installation This chapter provides you with instructions on how to setup your system The additional information shows you how to install memory 3 1 A Main Memory ADE 2100 provides one DDR2 SODIMM 200 pin Dual In line Memory Module to support 1 8V DDRAM Synchronized DRAM as on board main memory The maximum memory size is 1 GB with using 256MB 512MB 1GB technology Supports up to 2 double sided SODIMM at DDR2 400 533MHz The memory architecture adopts 128 bit data interface to support for x8 x16 and x32 DDRAM DDR2 device width In addition it only supports Non ECC memory For system compatibility and stability don t use memory module without brand You can also use the single or double side SODIMM Without out the contact and lock integrity of memory module with socket it will impact on the system reliability Follow normal procedure to install your DDRAM module into memory socket Before locking make sure that the module has been fully inserted into the SODIMM slot Mounting Notch Notch Key Ejector Tab NOTE For maintaining system stability do not change any of DDR2 memory parameters in BIOS setup to upgrade your system performance without acquiring technical information 22 50 ADE 2100 User s Manual 3 2 Installing the 3
31. t Ultra DMA 33 select Auto to enable BIOS support The choice Auto Disabled 4 2 4 1 7 IDE HDD Block Mode Block mode is also called block transfer multiple commands or multiple sector read write If your IDE hard drive supports block mode most new drives do select Enabled for automatic detection of the optimal number of block read writes per sector the drive can support The choice Enabled Disabled 36 50 ADE 2100 User s Manual 4 2 4 2 VIA OnChip PCI Device em MEN Phoenix fiuardBIOS CMOS Setup Utility o VIA OnChip PCI Device Azalia HDA Controller Auto Item Help Enabled Onboard Lan 1 Device Onboard Lan 2 Device Enabled Menu Level gt gt Tle lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults 4 2 4 2 1 Azalia HDA Controller This item allows you to select the chipset family to support AC97 Audio The choice Auto Azalia AC97 Audio and Modem AC97 Audio only AC97 Modem only All disabled 4 2 4 2 2 Onboard Lan 1 2 Device Select Enabled if your system has a LAN device installed on the system board and you wish to use it The choice Enabled Disabled 37 50 ADE 2100 User s Manual 4 2 4 3 Super IO Device Phoenix AwardBIOS CMOS Setup Utility Super I0 Device Onboard Serial Port 1 3F8 IRQ4 1 Item Help Onboard Serial Port 2 2F8 IRQ31 Menu Level gt gt Tle lt Move Enter
32. th rats 44 428 Prequency Voltage Control pp 45 4 2 9 Load Fail Safe DSTA UM rtepa temor dioett tu etd se tae etna aeneae 46 42 10 Load Optimized Defaults pp 47 4 2 11 Supervisor User Password Setting pp 47 42 42 Exit Selecto M Rm 49 5 50 Revision History ADE 2100 User s Manual Revision Date Comment Rev 1 0 Jan 2007 Initial released 6 50 O CHAPTER 1 ADE 2100 User s Manual 1 Introduction 1 1 Description The ADE 2100 is designed in a 3 5 embedded form factor to fit the low power VIA V4 Bus Eden processor onboard to meet today s demanding pace and to keep complete compatibility with hardware and software function supported The on board devices support VIA Eden 1 0 GHz processor integrated graphics and dual Ethernet controllers It s beneficial to build up a fanless system integrator This board hosts VIA V4 Eden processor with FSB 400 MHz in combination with the VIA CX700M chipset with an integrated graphic memory controller up to 128 MB and supports dual view function with VGA LVDS amp VGA DVI with one SODIMM up to 1 GB DDR2 400 533 MHz enhanced on board one PCI IDE interface supporting 2 drives of Ultra ATA33 synchronous mode feature an onboard Super I O chipset for two serial ports one RS 232 serial port interface and one RS 232 422 485 pin header Besides integrated Realtek ALC883 AC97 codec Hi speed USB 2 0 x 6 ports offering greater bandwidth over US
33. the time the AGP bus mastering device has to wait before it can initiate a write command to only one wait state This speeds up all writes that the AGP bus master makes to the system memory 4 2 3 2 8 AGP 3 0 Calibration Cycle This BIOS feature controls the AGP 3 0 calibration cycle feature of the motherboard chipset It is only found in motherboards that support the AGP 3 0 standard 4 2 3 2 9 VGA Share Memory Size This BIOS feature controls the amount of system memory that is allocated to the integrated graphics processor when the system boots up 4 2 3 2 10 Direct Frame Buffer This BIOS feature controls the processor s access to the section of system memory reserved for use by the integrated graphics processor as graphics memory Please note that we were referring to the CPU not the graphics processor 4 2 3 2 11 Panel Type This item allows you to select the panel resolution 4 2 3 2 12 Outport Port This item allows you to select LVDS signal output port 4 2 3 2 13 Dithering This item allows you to enable or disable Dithering function The choice Enabled Disabled 33 50 ADE 2100 User s Manual 4 2 3 3 CPU amp PCI Bus Control Phoenix fiuardBIOS CMOS Setup Utility gt zx CPU amp PCI Bus Control PCI Master O WS Write Enabled Item Help PCI Delay Transaction Enabled DRDY_Timing Optimize Menu Level gt gt Tle lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values
34. wafer CN15 Auxiliary power connector 1 x 4 wafer CN16 Internal USB connector 5 amp 6 2 x 5 header DIMM1 200 pin DDR2 SODIMM socket SATA1 SATA2 U15 Serial ATA connector 1 amp 2 CompactFlash card connector 16 50 ADE 2100 User s Manual 2 3 Jumpers Connectors Setting 2 3 1 RTC CMOS Clear Select JP1 2 3 2 COM2 RS 232 422 485 Select JP2 PIN No Description PIN No RS 232 x RS 422 RS 485 Normal operation 2 3 3 BIOS Write Protect JP3 2 3 4 AT ATX Power Select JP4 PNNo Description PNNe Description BIOS write unabled ATX Power BIOS write enabled 2 3 5 PS 2 Keyboard amp Mause CN1 2 3 6 Power Connector CN2 NT Description PINNo Description am Keyboard Data 5VSB a MERE D RENE 45V Keyboard Clock 6 Mouse Clock 2 3 7 ATX Power Connector CN7 2 3 8 Auxiliary Power Connector 2 CN15 PNNo Description PINNo zn 2 3 9 Audio Connector CN3 PNNo Description XE 2 Green 3 Fed 17 50 2 3 10 COM1 VGA Connector CN4 ADE 2100 User s Manual COM1 VGA BiNNo Description Description PIN No PIN No Description 1 baacanerbeed 2 Received Data 3 Temmibta Gewd o 5 Gud 4 Data Terminal Ready Ground 8 7 rund Ground 10 9 Clear To Send PY ts c6 8 9 Aingingicator 2 3 11 LAN 1 2 amp USB 1 2 3 4 Connectors CN5 CN6 LAN 1 2 NC
35. xit F1 General Help F5 Previous Values F6 Fail Safe Defaults F Optimized Defaults 35 50 ADE 2100 User s Manual 4 2 4 1 1SATA Controller Select Enabled if your system has a S ATA device installed on the system board and you wish to use it The choice Enabled Disabled 4 2 4 1 2IDE DMA Transfer Access This item allows you to enable or disable IDE DMA transfer access The choice Enabled Disabled 4 2 4 1 3 OnChip IDE Channel1 Select Enabled to activate IDE channel separately The choice Enabled Disabled 4 2 4 1 4IDE Prefetch Mode This BIOS feature controls the IDE controller s prefetch buffer Whenever the processor requests for data from a drive the IDE controller can prefetch the data following it If the processor requests for the subsequent blocks of data it can be quickly satisfied by the prefetched data 4 2 4 1 5 Secondary Master Slave PIO The two IDE PIO Programmed Input Output fields let you set a PIO mode for each of the four IDE devices that the onboard IDE interface supports Modes 0 through 4 provide successively increased performance In Auto mode the system automatically determines the best mode for each device 4 2 4 1 6 Secondary Master Slave UDMA Ultra DMA 33 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver Windows 95 OSR2 or a third party IDE bus master driver If your hard drive and your system software both suppor

ADE-2100 1st Manual

Contents

Download Pdf Manuals

Related Search

Related Contents