Home

Untitled

1. Value Type of control 16 bit 8 bit Colours macros CMY and color wheel 48 55 Macro 6 56 63 Macro 7 64 71 Macro 8 72 79 Macro 9 80 87 Macro 10 88 95 Macro 11 96 103 Macro 12 104 111 Macro 13 112 119 Macro 14 120 127 Macro 15 128 135 Macro 16 136 143 Macro 17 144 151 Macro 18 152 159 Macro 19 160 167 Macro 20 168 175 Macro 21 176 183 Macro 22 184 191 Macro 23 192 199 Macro 24 200 207 Macro 25 208 215 Macro 26 216 223 Macro 27 224 231 Macro 28 232 239 Macro 29 240 247 Macro 30 248 255 Macro 31 Effect wheel 0 70 Full beam step 71 180 Beam shaper proportional 181 255 Frost filter step Shutter strobe 0 31 Shutter closed step 32 63 No function shutter open step 64 95 Strobe effect from slow to fast max 10 flashes s proportional 96 127 No function shutter open step 128 159 Pulse effect in sequences proportional 160 191 No function shutter open step 192 223 Random strobe effect from slow to fast proportional 224 255 No function shutter open step Dimmer intensity Gradual adjustment of the dimmer intensity proportional from 0 to 10096 11 6 Addressing The control board on the top side of the SERVOCOLOR allows you to assign the DMX fixture address which is defined as the first channel from which the SERVOCOLOR will respond to the controller If you set for example the address to channel 5 the SERVOCOLOR will use the channel 5 to 20 for control Please be sure that you don t ha
2. 0 CyAG NAGO YELO CSPD O PEa dinl PAn tuit 5842 fo CYA NAG YEL CSP ft SHAI Skri dal PHa3 tilt 5843 Co 2 2 NAG YEL CSP2 2 SHRe 66 9 AY 5245 Col 986 NAGS 5 5 5 1810 SHAS di nE Lamp On automatically This function enables to switch On the lamp automatically after switching On the fixture Use the Up and Down keys to select On if you wish to switch On the lamp automatically after switching On the fixture or Off if you wish the lamp off after switching On the fixture and press Enter to confirm or Mode to cancel and return to the menu DMX values Readout DMX values of each channel received by the fixture Use the Up and Down keys to select desired channel and press Enter to read its value coming to the fixture or Mode to cancel and return to the menu 16 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 50 Automatic blackout of Display This function allows you to keep the display On or to turn Off automatically 2 minutes after last pressing any key on the control board Use the Up and Down keys to select On if you wish to keep the display On or Off if you wish to turn Off automatically 2 minutes after last pressing any key on the control board and press Enter to confirm or Mode to cancel and return to the menu By this function you can adjust from 20 to 100 the intensity of the display Use the Up and Down k
3. s noman 6 noman Laie EET om Cad NEN 253030 03 5 0 00 20 3 Standart protocol Standart protocol Standart protocol Standart protocol Standart protocol Standart protocol Standart protocol 1 2 3 5 7 10 11 12 13 14 15 6 After having calibrated required functions press Enter to confirm or Mode to cancel and return to the menu without reset by the ArES function and use the ArES function in order to write the calibration values to the memory EEPROM and to make a reset in order to check the new adjusted positions of the colour and CMY wheels 20 9 Error and information messages HEAt This message appears if you try to switch on the lamp within 5 minutes after having switched it off the lamp is too hot The message will appear on the display if the lamp doesn t ignite within 28 seconds The SERVOCOLOR will store this information and automatically ignite the lamp when the 5 minutes period has expired LAEr The ignition of the lamp is seven times unsuccessful the HEAt message appeared six times before and the display shows meaning that the lamp could be damaged or even missed the fixture is overheating this can occur if the ambient temperature is 45 C or more or there could be a failure on the ignitor or ballast Please place or replace the lamp check the ambient temperature or contact your dealer if the situation was not caused by the lamp
4. MbEr This messsage informs you that the main PCB does not communicate correctly with the Control Board CoEr color wheel error This messsage will appear after the reset of the fixture if the magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective or its driver circuit on the main PCB The color wheel is not located in the default position after the reset FtEr This error message informs you that the fixture was overheating occured if the ambient temperature is 459 more and that the relay switched off the lamp This message will appear on the display until the temperature will be on a suitable level then the display will show the message meaning the lamp is too hot explanation see above SnEr This message appears if the lamp lighting sensor is failed PoEr This message will appear if the fixture was shortly disconnect from the main PAEr PAN yoke movement error This message will appear after the reset of the fixture if the yoke s magnetic indexing circuits malfunction sensors failed or magnet missing or the stepping motor is defective Or its driving IC on the main PCB The yoke is not located in the default position after the reset tiEr TILT head movement error This message will appear after the reset of the fixture if the head s magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective Or its drivi
5. mains Connect the fixture to the mains with the enclosed power plug The earth has to be connected The occupation of the connection cables is as follows L Brown Live Blue Neutral Yellow Green Earth 4 5 DMX 512 connection connection between fixtures The wires must not come into contact with each other otherwise the fixtures will not work at all or will not work properly Only use a stereo shielded cable and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another Occupation of the XLR connection DMX output DMX input XLR mounting socket XLR mounting plug 1 Ground 1 Ground 2 Signal 2 Signal 3 Signal 3 Signal If you are using the standard DMX controllers you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain If you wish to connect DMX controllers with other XLR outputs you need to use adapter cables Building a serial DMX chain Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture Always connect one output with the input of the next fixture until all fixtures are connected
6. Caution At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 W resistor between Signal and Signal into a 3 pin XLR plug and plug it in the DMX output of the last fixture 5 DMX PROTOCOL hannel Channel Value Type of control 16 bit 8 bit Pan movementbyss0 000000 255 movement Pan movementbyss0 530 Pan fine 0 255 Fine control of pan movement proportional Tilt 0 255 Tilt movement by 280 proportional Tilt fine 0 255 Fine control of tilt movement proportional Speed of PAN TILT movement 0 Max speed tracking mode step 1 249 From max speed to min speed vector mode proportional 250 255 Max speed black out while PAN TILT moving or step color changes tracking mode Lamp on off reset fans speed control From max speed of fan to min speed of fan proportional Lamp on reset step No function step Lamp off after 3 sec step No function step Colours Open white step Red step Blue step Green step CTF 3200 K step CTF 5600 K step UV filter step Forwards rainbow effect from fast to slow proportional No rotation step Backwards rainbow effect from slow to fast proportional Cyan Cyan 0 white 255 full cyan proportional Magenta Magenta 0 white 255 full magenta mH Yellow Yellow 0 white 255 full yellow proportional Colours macros CMY and color wheel Off Macro 1 Macro 2 Macro 3 Macro 4 Macro 5
7. DMX data link 7 Remotely controllable functions 7 1 Lamp The SERVOCOLOR is run with a MSD 250W 200W lamp A relay inside of the SERVOCOLOR allows you to switch On and Off the lamp via itself control board on the front panel or via your controller without affecting the rest of the lighting 7 2 Switching On and Off the lamp by Control Board 1 Switch On the SERVOCOLOR and wait until the fixture reset has finished 2 Press the Mode key in order to access the main menu Browse through the menu by pressing the Up and Down keys until the display shows LAMP Confirm by pressing Enter key 3 Use the Up and Down keys to select On for switch On the lamp and Off for switch Off the lamp and press Enter to confirm or Mode to cancel Note It is also important to note that the discharge lamp is cold restrike types that means that they have to be cold before re striking For this reason you have to wait 5 minutes max speed of fan must be adjusted after having switched Off the lamp before you can switch it back On again If you try to switch On the lamp within 5 minutes after having switched it Off the SERVOCOLOR will store this information and automatically ignite the lamp when the 5 minutes period has expired The message will appear on the control board display at the back side of the SERVOCOLOR If the ignition of the lamp is seven times unsuccessful on the display will appear LA Er meaning that the lamp c
8. SIERVOCOLOR auromoated light system USER MANUAL Copyright ServoColor Table of contents t Safety INSU UC eon diet cta e Fx FURY aba eie CHOR TE LEER LE bx e SP 4 2 Operating 5 2481 1111 011911 21 COVICC HE 6 ZA rci ETATS 7 2E Fitting IB OD ette acce c REC f poete Ut tet Rel eles noah eR Al 7 2 9 Rigging the fixture al at caet Mot el en eee ac tue ti 8 4 4 Connection to the 9 4 5 DMX 512 connection connection between 9 5 DMX PROTOCOL a bark du ara canada Le ru sw re o e d cx LX a e ccc eens 10 5 Addressihd 12 7 Remotely controllable functions 12 251 2 2 2220655555 4552 28356288 251225524222542 25885358 281 12 7 2 Switching On and the lamp by Con
9. a dimmer pack Do not switch the fixture on and off in short intervals as this would reduce the lamp s life During the initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective Do not touch the device s housing bare hands during its operation housing becomes hot For replacement use lamps and fuses of same type and rating only CAUTION EYEDAMAGES Avoid looking directly into the light source meant especially for epileptics 4 2 Operating determinations This device is a moving head spot for creating decorative effects This product is only allowed to be operated with an alternating current of 230 V 50 Hz and was designed for indoor use only If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature Never run the device without lamp Do not shake the device Avoid brute force when installing or operating the device Never lift the fixture by holding it at the projector head as the mechanics may be damaged Always hold the fixture at the transport handles When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own and the safety of
10. ct may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock burns due to ultraviolet radiation lamp explosion crash etc 3 Description of device 1 Moving Head 2 Yoke 3 Base 4 Carrying handles Rear panel Power switch 5 6 DMX output 7 DMX input 8 Powercord 9 Fuseholder Front panel 10 Mode button 11 Enter button 12 Up button 13 Down button 14 Display 4 Installation 4 1 Fitting the lamp DANGER Install the lamps with the device switched off only Unplug from mains before To insert the lamp MSD 230V 250W or MSD 230V 200W open the small cover at the rear of head See the drawings by loosening the 2 Phillips screws on the cover Gently pull out the lamp assembly If changing the lamp remove the old lamp from the socket Insert the lamp to the socket Do not install a lamp with a higher wattage A lamp like this generates temperatures the device is not designed for Damages caused by non observance are not subject to warranty Please follow the lamp manufacturer s notes Do not touch the glass bulb bare hand during the installation Make sure that the lamp is installed tightly into the lampholder system Reinsert the lamp assemby and ti
11. er button Power On time By this option you can read the total number of hours that the SERVOCOLOR has been powered On Press Enter or Mode to return to the main menu Switch On Off the lamp Use the Up and Down keys to select On if you wish the switch On the lamp or Off if you wish switch Off the lamp and press Enter to confirm or Mode to cancel and return to the main menu m This function allows you to run a special demo test sequences without an external controller which will show you some possibilities of using SERVOCOLOR Press Up and Down keys to select the Mod1 sequences The Mod1 is suitable for projections on the wall ceiling or ground without any head movement the Mod2 uses all SERVOCOLOR functions and therefore is good for a complete introduction of the fixture 0 255 0 255 0 255 run Press Enter key to run reset This option enables the SERVOCOLOR to index all effects functions and return to their standard positions 8 2 SPEC Special functions Use the Up and Down keys to browse through the special functions and select the one by pressing Enter 15 Manual control of effects This function allows you to control manually the channel functions of the fixture Use the Up and Down keys to select desired function and press Enter to adjust the effect or Mode to cancel and return to the menu Lola L PAn tib SPd
12. etting effects calibration via control panel with 4 digit LED display Readout fixture and lamp usage receiving DMX values temperature etc Built in analyzer for easy fault finding error messages Remotely switching of the lamp Bilt in demo sequences Black out while head moving or color changing Silent fans cooling remotely controllable speed of fans Self resetable thermo fuse Digital serial input DMX 512 DMX control via every standard DMX controller 14 8 bit Pan Tilt movement resolution 16 16 bit Pan Tilt movement resolution Channel 1 Horizontal mirror movement 8 bit Channel 2 Fine Horizontal mirror movement 16 bit Channel 3 Vertical mirror movement 8 bit Channel 4 Fine Vertical mirror movement 16 bit Channel 5 Pan Tilt speed Channel 6 Fan speed On Off lamp reset Channel 7 Colours wheel Channel 8 Cyan Channel 9 Magenta Channel 10 Yellow Channel 11 Speed of CMY and Dimmer Channel 12 Colours macros CMY and colour wheel Channel 13 Beam effect Channel 14 No function Channel 15 Shutter strobe Channel 16 Dimmer Pan Tilt Pan movement range 530 Tilt movement range 280 8 16 bit movement resolution Automatic Tilt position correction Maximum PAN movement 530 in 2 65 s Maximum TILT movement 280 in 1 68 s Remotely controllable speed of Pan Tilt movement for easy programming Rigging Stands directly on the floor Mounts horizontally or
13. eys to select the level of the display intensity and press Enter to confirm or Mode to cancel and return to the menu This function allows you to switch Off the lamp by DMX Use the Up and Down keys to select On if you want to switch Off the lamp by DMX or Off if you don t want to switch Off the lamp by DMX and press Enter to confirm or Mode to cancel and return to the menu Temperature Temperature readouts of fixture inside in Celsius Inside temperatures below 70 C are not critical 70 C and more lead to the lamp being switched off Please note that the outside temperature should not exceed 45 C 1 N Low fan speed operating By using this function you can choose 3 types of low fan speed operating Browse through this menu by the pressing Up and Down keys the display shows step by step these messages HIGH reG LoOF Lo HI Press Enter if you wish to select one of them or Mode to cancel and return to the menu high max speed of fans The cooling fans work on max speed max cooling continuous controlling of the fan speed the fan automatically raises its speed in order to control inside temperature of the lighting if the temperature inside increases about certain level the low fan speed reduces the cooling of the lighting This cycle can repeat several times until the temperature inside is on suitable level low speed Switch Off the lamp operating the fan keeps the adjusted low speed un
14. ghten 2 screws again Before striking the lamp reset the LAti counter in the main menu of the Control Board by pressing the Up and Down buttons in one time and then confirming with the Enter button 2 phillips screws Do not operate this fixture with opened housing cover 4 2 Lamp adjustment The fixture lampholder is aligned at the factory Due to differences between lamps fine adjustment may improve light performance Strike the lamp and focus the light on a flat surface wall Center the hot spot the brightest part of the beam using the 3 adjustment screws B C Turn one screw at a time to drag the hot spot diagonally across the projected image If you cannot detect a hot spot adjust the lamp until the light is even To reduce a hot spot pull the lamp in by turning all three screws B C clockwise 1 4 turn at a time until the light is evenly distributed If the light is brighter around the edge than it is in the center or if light output is low the lamp is too far back in the reflector Push the lamp out by turning the screws B C counterclockwise 1 4 turn at a time the light is bright and evenly distributed Rx room tem screws B Aon BY turning sc ews X Y ang gt 9 Wait at least 15min before opening the covers ahd removing x WARING Disconnect the fixture from AC power before re la
15. gs The letter A flashes Use the Up and down keys to select required address 001 497 and press Enter to confirm or Mode to cancel and return to the main menu 13 Pan reverse This function allows you to invert the pan movement Use the Up and Down keys to select On if you wish this feature or Off if you don t wish this feature and press Enter to confirm or Mode to cancel and return to the main menu Tilt reverse This function allows you to invert the tilt movement Use the Up and Down keys to select On if you wish this feature or Off if you don t wish this feature and press Enter to confirm or Mode to cancel and return to the main menu Movement resolution By this function you can adjust the desired movement resolution 8 or 16 bit Use the Up and Down keys to select On if you wish the 16 bit high resolution or if you wish only 8 bit resolution and press Enter to confirm or Mode to cancel and return to the main menu Note If you adjust the 16 bit resolution the fixture will occupy 16 DMX channels if you adjust the 8 bit resolution the fixture will be operated by only 14 DMX channels Please check the DMX protocol Lamp On time This option enables you to read the total number of hours that the lamp has been powered On Press Enter or Mode to return to the main menu In order to reset the counter to 0 you have to hold the Up and Down button and press the Ent
16. mping Lamp is hot Risk of fire Protect hands and eyes lamp from fhe fixture dofestic use erature t 49 ews PE 2 4 3 Rigging the fixture Danger of fire When installing the device make sure there is no highly inflammable material decoration articles etc in between a distance of min 0 5 m The SERVOCOLOR can be placed directly on the stage floor or rigged in any orientation on a truss without altering its operation characteristics see the drawing The fixture s base enables to be mounted in two ways Use the clamps with screws M10 01 x XX Install a safety wire that can hold at least 10 times the weight of the fixture Never use the carrying handles for secondary attachment 5 XXX 24A 0000000 100000000 Warning Use 2 clamps to rig the fixture on the truss Follow the instructions mentioned at the bottom of the base Make sure that the device is fixed properly Ensure that the structure truss to which you are attaching the fixtures is secure Secure chain 4 4 Connection to
17. ng IC on the main PCB The head is not located in the default position after the reset FrEr It will appear if the frequency of the main is not standard 50 or 60Hz 10 Technical specifications Power supply Voltage oreet 210 230 250 V AC 50 60 Hz 3 15 250 Power consumption 500 W 21 Motors 9 high quality stepping motors controlled by microprocessors Compatible lamps MSD HSD 230 V 250 W GY 9 5 or MSD HSD 230 V 200 W GY 9 5 Optical system High luminous efficiency parabolic reflector Fresnel lens of diameter 150 mm Manualy adjustable beam angle from 8 to 22 Beampath H o Min beam angle 8 6560 1640 729 410 LUX c c e o e o 5 10 15 20 Distance m 0 0 70 1 40 2 10 2 80 Diameter m o Max beam angle 22 4051 1013 450 253 LUX i 2 1 4 amp S 2 m3 4 0 5 10 15 20 Distance m 1 94 3 89 5 83 7 77 Diameter m Colours CMY colours mixing system 6 dichroic filters plus white Red green blue colors and 3200 K 5600K UV filters Colour wheel continuos rotation in both directions rainbow effect Beam effects Beam shaper Wide and flat beam can stepplesly be rotated by 90 Frost filter for softer beam 22 Strobe Strobe effect with variable speed 1 10 flashes per second Dimmer Smooth dimmer from 0 100 Electronics Addressing special functions s
18. olutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual Important The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device Please consider that damages caused by manual modifications to the device are not subject to warranty Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Make sure that the available voltage is not higher than stated on the rear panel Always plug in the power plug least Make sure that the power switch is set to OFF position before you connect the device to the mains The power plug has to be accessable after installing the device Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord This device falls under protection class Therefore it is essential to connect the yellow green conductor to earth The electric connection repairs and servicing must be carried out by a qualified employee Do not connect this device to
19. on 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 1 Calibration via the control board Press Enter and the Up and Down keys in order to display the following messages Colo CYAn MAGE YELL for very smooth function calibration Select one of them press Enter and use the Up and Down keys in order to adjust their right value from 0 to 255 Then press Enter to confirm or Mode to cancel and return to the menu This can be repeated for each calibration parameter if it is required When the calibration is finished itis necessary to use the ArES function in order to write the calibration values to the memory EPROM and to make a reset in order to check the newly adjusted positions of the colour and CMY wheels When the reset of the fixture is finished the display will show the FCAL message Press Enter to repeat the calibration or Mode to return to the AdJ menu 19 2 Calibration external controller Press Enter and the Up and Down keys in order to display the following messages Colo CYAn MAGE YELL calibration parameters Select one of them and press Enter Now you can calibrate the colour and CMY wheel by your controller The DMX calibration protocol is described in the table DMX Calibration protocol DMX chanel Calibration 0 255 Calibration 0 255 Magenta Calibration 0 255 4 Yellow Calibration 0 255 CEN p 5 os vw
20. others The minimum distance between light output and the illuminated surface must be more than 1 meter Make sure that the area below the installation place is blocked when rigging derigging or servicing the fixture Always fix the fixture with an appropriate safety rope Fix the safety rope at the correct holes only Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened The lamp must never be ignited if the objective lens or any housing cover is open as discharge lamps may explose and emit a high ultraviolet radiation which may cause burns The maximum ambient temperature t 45 C must never be exceeded Otherwise the lamp is switched off and the fixture is out of operation for 5 minutes CAUTION The lens has to be replaced when it is obviously damaged so that its function is impaired e g due to cracks or deep scratches Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation CAUTION The lamp has to be replaced when it is damaged or deformed due to the heat Please use the original packaging if the device is to be transported Please consider that unauthorized modifications on the device are forbidden due to safety reasons If this device will be operated in any way different to the one described in this manual the produ
21. ould be damaged or even missed or there could be a failure on the ignitor or ballast 7 3 Colour wheel The SERVOCOLOR features a colour wheel with 7 color positions 6 of these with dichroic colors and the last one open It is also possible to rotate the color wheel continuously at different speeds the so called Rainbow effect is created 7 4 CMY colours mixing system The CMY color mixing system is based on graduated cyan magenta and yellow color filters A continuous range of colors may be achieved by varying the amount of each filter from 0 to 100 12 7 5 5 The beam shaper allow you to widen and flatten beam Beam shaper rotates 180 Frost filter on the same wheel as beam shaper softens the beam 7 6 Dimmer Smooth 0 100 dimming is provided by the special dimmer unit 7 7 Shutter Strobe Extremely fast shutter may also be used for strobe effect 1 10 flashes per second 7 8 Fan The SERVOCOLOR is cooled by free axial fans two in the projector head and one in the base The speed of the fan and of course the noise can be continuously reduced if very quiet performance is required By the Control Board using the FAnS function you can choose 4 types of low fan speed operating 1 High high max speed of fans The cooling fans work on max speed max cooling 2 reg continuous controlling of the fan speed the fan automatically raises its speed in order to control inside temperatu
22. re of the lighting if the temperature inside increases about certain level the low fan speed reduces the cooling of the lighting This cycle can repeat several times until the temperature inside is on suitable level 3 loof low speed Switch the lamp operating the fan keeps the adjusted low speed until the temperature exceeds max inside temp Then the SERVOCOLOR automatically switch Off the lamp 4 lohi low high speed of the fan operating the fan keeps the adjusted low speed until the temperature exceeds max inside temp of the fixture then the SERVOCOLOR automatically switch from low to high the fan speed 8 Control Board The control board situated on the front panel of the SERVOCOLOR offers several features You can simply set the lighting address read the number of lamp or unit hours switch On and Off the lamp run test show make a reset and also use special functions for manual demo and service purposes The main menu is accessed by pressing the Mode key press this one so many times until the display shows message A001 with actually stored address Browse through the menu by the pressing Up and Down keys the display shows step by step these messages A001 rPAn rTilt 16br Lati Poti LAMP dEMo rESE SPEC Press Enter if you wish to select one of them The functions provided are described in the following sections and the function hierarchy is shown below 8 1 Main functions DMX 512 Address settin
23. til the temperature exceeds max inside temp then the SERVOCOLOR automatically switch Off the lamp low high speed of the fan operating the fan keeps the adjusted low speed until the temperature exceeds max inside temp of the fixture then the SERVOCOLOR automatically switch from low to high the fan speed Default settings Press Enter to reset all fixture personalities not the adjusting functions to the default values On the display will appear rSt meaning that the fixture makes the reset See the table of personality setting and their default positions 18 Default values Personality Display SHADED J Pan reverse Tilt reverse Movement resolution a wa C 1 Automat blackout of display Display intensity Lamp Off via DMX Low fan speed operating Adjusting the default positions of colour and CMY By this function you can calibrate and adjust the colour and CMY to their standard right positions Use the Up and Down keys to browse through the adjusting menu the display shows step by step these messages PAn Tilt SPEd Colo CYAn MAGE YELL MACr EFEC Stro dimr FCAL by which you can adjust the fixture to the required desired position 0 255 before the function calibration Then when the positioning is finished use the last FCAL function Fixture calibrati
24. trol Board 12 7 3 GolbUr Wheel eo hr bete Dd Mese adis 12 7 4 CMY colours mixing SVStelTi uec 4 b dei eot ed sb bte uds 12 7 9 Beam Effo C EE 13 TO DIMMET aimara a e a US A eE E EED 13 ohuler Strobe oi He bte beg a se ideae 13 Fo pM TS 13 8 Control B ard 13 8 1 13 25 foedera ate 15 9 Error and information 21 10 Technical specifications 2 21 11 Maintenance and cleaning 24 12 dte DE 25 CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START UP 1 Safety instructions Every person involved with installation and maintenance of this device have to be qualilfied follow the instructions of this manual CAUTION Be careful with your operations With a voltage of 230V you can suffer a dangerous electric shock when touching the wires This device has left our premises in abs
25. use too Only replace the fuse by a fuse of same type and rating T 3 15 A 250 V slow Before replacing the fuse unplug mains lead Procedure Step 1 Unscrew the fuseholder on the rear panel with a fitting screwdriver from the housing anti clockwise Step 2 Remove the old fuse from the fuseholder Step 3 Install the new fuse in the fuseholder Step 4 Replace the fuseholder in the housing and fix it 24 12 Appendix We believe you will enjoy your SERVOCOLOR We assure you will enjoy this product for years if you follow the instructions given in this manual If you have any questions and comments please do not hesitate to contact us Please note errors and omissions for every information given in this manual excepted Every information is subject to change without prior notice Any claim due to missing or wrong information in this manual is herewith excluded 25
26. ve any overlapping channels in order to control each SERVOCOLOR correctly and independently from any other fixture on the DMX data link If two three or more SERVOCOLOR are addressed similarly they will work similarly For address setting follow this procedure 1 Switch On the SERVOCOLOR and wait until the fixture reset has finished rSt is flashing at the display 2 Press the Mode key in order to access the main menu Browse through the menu by pressing the Up and Down keys until the display shows A001 Confirm by pressing Enter key and the letter A will flash 3 Use the Up and Down keys to select the desired address 4 Confirm by pressing Enter or Mode to cancel Controlling After having addressed all SERVOCOLOR you may now start operating these via your lighting controller Note After switching on the SERVOCOLOR will automatically detect whether DMX 512 data is received or not If there is no data received at the DMX input the display will startto flash A001 with actually set address This situation can occur if the 3 PIN XLR plug cable with DMX signal from controller is not connected with the input of the SERVOCOLOR the controller is switched off or defective if the cable or connector is defective or the signal wires are swap in the input connector Note It s necessary to insert the XLR termination plug with 120 Ohm in the last lighting in the link in order to ensure proper transmission on the
27. vertically with 2 clamps 2 truss orientation Safety chain cord attachment point 23 Temperatures Maximum ambient temperature 45 C Maximum housing temperature t steady state 80 C Dimensions and weight Length of base including handles 372 mm Width of yoke 426 mm Height head horizontal 500 mm Weight net Shipping weight 00000000 00000000 379 11 Maintenance and cleaning It is absolutely essential that the fixture is kept clean and that dust dirt and smoke fluid residues must not build up on or within the fixture Otherwise the fixture s light output will be significantly reduced Regular cleaning will not only ensure the maximum light output but will also allow the fixture to function reliably throughout its life A soft lint free cloth moistened with any good glass cleaning fluid is recommended under no circumstances should alcohol or solvents be used DANGER Disconnect from the mains before starting any maintenance work The fresnel lens will require weekly cleaning as smoke fluid tends to building up residues reducing the light output very quickly The cooling fans should be cleaned monthly The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air jet The dichroic colour filters should be cleaned monthly Replacing the fuse If the lamp burns out the fine wire fuse of the device might f

Untitled

Contents

Download Pdf Manuals

Related Search

Related Contents