Micron Z4120 alarm
Contents
1. SCORPION 74120 Alarm Controller As installed by Eagle Alarms 09 5357117 www eaglealarms co nz User Instructions Using the Scorpion Z4120C alarm controllers The Keypad The Scorpion Z4120C and Z8020C communicate system status through the keypad beeper During an arming cycle the beeper will sound for the entire exit time This is a leave now warning Scorpion will arm at the expiry of this period On entry the beeper sounds for the programmed entry period Ifa valid user code is entered to disarm the system the beeper emits two short tones An incorrect entry is signalled by one long tone The Status Lamp The yellow status lamp is used to indicate several conditions Yellow lamp on the system is armed or arming Yellow lamp off the system is disarmed Yellow lamp flashing an alarm has occurred a system fault exists or the panic function has been activated The Mains Lamp The Mains lamp is on when mains power is applied In the event of a mains failure the Mains light flashes until mains power is restored and an arm disarm cycle is completed The Mains lamp also flashes to indicate a low battery condition When the battery is restored to full charge and an arm disarm cycle is completed the Mains lamp stops flashing The Armed Lamp The Armed lamp illuminates when the system is armed The Armed lamp also flashes to indicate when an alarm condition has occurred User Cod2. er a valid user code then all zone LED s light followed by the zone number s to be excluded those zone LED s turn off then press Example to arm the system with zones 4 and 5 excluded press DAGAA then amp then then Disarming the System Follow the same sequence as for arming enter a valid two three or four digit user code then OSOD then The keypad will beep twice and the yellow status light will turn off A flashing yellow status lamp indicates that one or more zones have been alarmed The zone lamps for any zones which have alarmed will flash until the next arming cycle Note the zone number s and notify your installer or security monitoring company If the yellow status lamp is flashing and no zone lamps are flashing the alarm condition may have been caused by a system fault press 8 9 then on your keypad The following table indicates the type of alarm condition that has occurred Zone 1 lamp flashes Alarm caused by a nitewatch two key medical or fire panic Zone 2 lamp flashes The battery has discharged or is faulty Zone 3 lamp flashes Mains power to the alarm has failed Zone 4 lamp flashes A dialler communications error has occurred Zone 5 lamp flashes Phone line is faulty or is disconnected Zone 6 lamp flashes Siren output or auxiliary power supply overloaded or open circuit Hold Down Commands To use a hold down command the function key keypad digit must be pressed and held dow
3. es Scorpion Z4120C and Scorpion Z8020C are each capable of storing up to twenty four user codes Each user code may be two to four digits in length and each may be programmed with one or all of six different functions Each user code may be programmed As a user code that can arm and or disarm the system from a touch tone phone As a user code that can select a partitioned area to arm Z8020C only As a master user code that can program other user codes As an arming code only can not disarm the system As a user code that does not report to a central station As a user code that can exclude zones at arming If no option is selected for a user code that code will perform a basic arm and disarm function only User code 1 is factory set as a master user code 1234 and should be changed to your own selection This user code can also be used to program the remaining user codes Your installer will need to assign the functions of each additional user code when your system is installed For example you may require user code 18 to be used by a domestic helper to arm but not disarm the system This restriction on code 18 will need to be pre set by the installer The code may be entered at a later time using the master code Use the user code attributes table in the rear of this user manual to record the functions for each code Adding Changing or Deleting a user Code Enter a valid master user code press keys 1 3 together then enter a new user code
4. n until a 2 key beep is heard Note that hold down commands will ONLY function when the alarm control is fully disarmed The following hold down commands are available Setting the Real Time Clock Time It is advisable but not mandatory to set the system Real Time Clock Check with your installer if the clock has been set The clock MUST be set if the Auto Arming feature is used Clock time is in 24 hour format To set the clock proceed as follows Press and hold down key 6 until a 2 key beep is heard then enter a master user code then then the time in 24 hour format then Example Setting the alarm system clock to 2 45 pm BEEP BEEP som 6 then G H thenO O O O Setting the Auto Arming Time Scorpion may be programmed to Auto Arm at a pre set time each day To access this feature an Auto Arming time must be programmed using the Hold Down 7 command Press and hold down key 7 until a 2 key beep is heard then enter a master user code then then the time to arm in 24 hour format then Example Setting the auto arming time to 5 30 pm son 7 then Z DOAA thn O O Q O If a valid auto arming time has been entered the keypad will sound three beeps every six seconds for the installer programmed pre alert time before auto arming At the end of the pre alert time the panel starts counting down the exit delay and sounds the leave now warning beeper then arms all zones During the pre alert en
5. tering any key at the keypad will abort the auto arming cycle Once the alarm has started the exit timer and warning beeper a valid user code is required to abort the arming cycle Entering an invalid auto arm time eg 2500 disables this function This is the factory default setting Note To enable Auto Arming it is also necessary to program the correct time into Scorpion s real time clock User Master Phone Arm area Report to Can Exclude User Initials Aor B Station Number
6. then enter then the user identifier 1 to 15 Repeat the procedure for adding other new user codes To delete user codes follow the same procedure but omit the new user code step Finish by entering a Example To change the master user code from 1234 to 1912 press the following sequence MAQEB 4 then Ci 3 then DAQS then 1 Your current code Together New code Arming the System Using Quickarm If your installer has programmed the quickarm option you can arm the system by entering 1 then For partitioned systems Z8020C only entering 1 will arm Area A and entering 2 will arm Area B Quick arming Scorpion O Using a User Code Enter a valid two three or four digit user code then ODODO then If all zones are clear the keypad sounds a repeating sequence of three short beeps for the duration of the exit delay and the yellow status lamp turns on The zone lamps for all zones that are arming are also turned on At the end of the exit delay the zone lamps extinguish and the system is now armed If a zone fault or potential alarm condition exists and the user attempts to arm the system the lamp s for those zone s flash and are accompanied by a repeating sequence of two long beeps This indicates that one or more of the zones are faulty or not secured The panel should be disarmed the problem located possible open door or window and the system re armed To Arm the System and Exclude a Zone s Ent
Download Pdf Manuals
Related Search