2010 TireWatch Eng usermanuel
Contents
1. VURE WEI YGA LITE TIRE PRESSURE MONITORING SYSTEM TIRE WATCH FOR MOTORCYCLE USER MANUAL Thank you for purchasing the TIRE WATCH tire pressure monitoring system TIRE WATCH will allow you to drive with more confidence and be alerted in the event of a slow leak or puncture The setup options for the TIRE WATCH system are detailed below IMPORTANT Read instructions completely before proceeding Please do not set the system values C until the sensor recognition is completed A KIT COMPOSITION 8 5 11 5 BMW 1 display button battery CR2450 1 clipbody 2 wheel unit sensors with 11 5XL nut and spring 1 bracelet 2 valves 1 handle bar screws kit 1 M5x20 screw 1M5 self locking 2 specific seals for some BMW rims see specificities nut 1 sleeve 2 seals for 8 5mm valve hole 1 motor body screw kit 2 M3 screws 2 M3 nuts 2 O 2 nuts for 8 5mm valve hole see specificities washers 1 peg for valve in spoke see specificities 1 steering column screw kit 1 compressible brace 1 1 connector position assurance CPA M5x40 screw 1 M5 nut with washer 1 clipbar B KNOW EVERYTHING ABOUT YOUR EQUIPMENT FIG 1 DISPLAY BUTTON FUNCTIONS Bt1 ON Scrolling menus Validation Backlight only Bt2 ON OFF Display Units Setting Swap from Pressure to Temperature backlight 4 seconds Tire Pressure or Temperature information Pressure bar PSI o2. LDL TECHNOLOGY JANUARY 2010 P17 VURSS LL Ugla LITE TIRE PRESSURE MONITORING SYSTEM J SAFETY AND GENERAL INFORMATION Users are not permitted to modify the device in any way TIRE WATCH TM is an information tool Proper inflation and tire maintenance are the responsibility of the vehicle driver Tire pressure must be to manufacturer recommended levels Always inflate your tires cold 23 C 73 F Tire values will be updated while driving USA Canada and European Union Directives Conformity Products marked CE are in compliance with Directive R amp TTE 99 5 EC Products marked FCC are in compliance with Directive FCC part 15 User precautions Never mount directly on a metal part you may prevent signal reception TIRE WATCH is rain proof Do not wash directly with a pressure washer or garden hose Avoid prolonged exposure to sunlight when not in use Do not repair or modify the TIRE WATCH This will void the warranty Repair must be done by an authorized facility Never use solvent only wash TIRE WATCH with water soap and soft cloth Ifyou drive close to strong radio or radar signals airport military base performance may be affected Warranty One year with factory receipt and warranty card LDL Technology reserves the right to modify its product and to bring any modification without preliminary notice COPYRIGHTS LDL TECHNOLOGY JANUARY 2010 P18
3. unit is Bar to change to PSI gt short push on Bt 2 to return to bar unit gt press againon Bt2 To save your unit choice press on Bt 1 To access the next menu Bt 1 Note Temperature unit is fixed to C FIG 6 MENU 03 FRONT LOW TIRE PRESSURE THRESHOLD SETTING Default range for front tire values 1 4 bar to 3 5 bar 20 to 51 PSI Minimum alert pressure LO pre programmed at 1 8 bar 26 PSI Set the values for front tire according to the tire manufacturer recommendation FIG 7 MENU 04 REAR LOW TIRE PRESSURE THRESHOLD SETTING Fis 7 Default range for rear tire values 1 4 bar to 3 5 bar 20 to 51 PSI Minimum alert pressure LO pre programmed at 1 8 bar 26 PSI Set the values for rear tire according to the tire manufacturer recommendation FIG 8 MENU 05 Front Rear Tire Values Are Reversed FIG 8 In case sensor values are reversed during the learning phase you can swap them in general front pressure is the lowest value Reach FIG 8 by an extended push on Bt 1 Then push shortly on Bt 2 To validate gt short push on Bt 1 To return to the main display gt long push on Bt 1 COPYRIGHTS LDL TECHNOLOGY JANUARY 2010 P13 VURLS LLL UYGA LITE TIRE PRESSURE MONITORING SYSTEM F RECOGNIZE YOUR WHEEL UNIT SENSORS Process to follow when you change one or two wheel unit sensors FIG 9 MENU 06 ID RECOGNITION A During all the learning process tires must a
4. ert the band through the slots beneath the bracket horizontally or vertically 2 Pull band with pliers 3 Attach the display Do not use the CPA clip with bracelet 1 Insert the screw into the bracket central hole screw kit n 14 2 Place the compressible spacer and nut on the screw and put it on the steering column tube 3 Screw until the bracket is correctly fixed NB do not exceed 2Nm 13 in lbs 4 Insert the CPA clip n 8 to secure the display FIG 19 CHANGE THE BATTERY FROM THE DISPLAY 1 Unscrew the battery cover on the back of the display using a coin 2 Replace the old battery with a new one CR2450 PANASONIC or MAXELL only as illustrated and screw again the battery cover Please check that the seal is correctly in place 3 Please dispose the old battery in a safe and proper manner COPYRIGHTS LDL TECHNOLOGY JANUARY 2010 P16 VURSS LLL YGA LITE TIRE PRESSURE MONITORING SYSTEM FIG 20 REMINDER FOR MOTOR DEALERSHIP FOR WHEEL UNIT SENSORS MOUNTING Screw the nut with a 5mm allen key Do not exceed 2 rounds per second and hold the valve while screwing to prevent it from turning around A Final torque 4 2Nm 0 2Nm 37 2 in lbs 1j77in lbs The sensor must not get in touch with the tire during the mounting process SPECIFICITIES SPECIFICITIES Valve hole Flat seat KTM Moto Guzzi Valve hole Curved seat Special Rim OZ racing Dymag COPYRIGHTS
5. ls are blinking Drive more than 20 Mph until Pressure values are displayed time out 4 minutes To invert the front and rear wheel unit sensor location gt FIG 8 MENU 05 Tire values are reversed If this learning phase fails dashes will be displayed instead pressure values You must repeat the ID sensor recognition process A Switch off the display and wait 8 minutes motorcycle stopped before repeating this phase If the pressure values are not displayed after several trials please contact your dealer D VALUES amp ALARM SETTINGS Proceed to the scrolling menu gt long push on Bt 1 Once the wanted menu is reached gt the first digit blinks to prompt you to enter the value to set the 1st digit gt short push on Bt 2 until the wanted value is reached To validate the 1 digit and set the 2 digit gt short push on Bt 1 Repeat the operation until the last digit To validate the last digit and the on going menu short push on Bt 1 To proceed to the next menu short push on Bt 1 To go back to the standard mode FIG 3 gt long push on Bt 1 COPYRIGHTS LDL TECHNOLOGY JANUARY 2010 P12 YURE WEI YGA LITE TIRE PRESSURE MONITORING SYSTEM E SET YOUR VALUES BY USING THE SCROLLING MENU FIG 4 MENU 01 HOUR SETTING mem Proceed to the scrolling menu gt long push on Bt 1 Adjust your values as described in chapter D FIG 5 MENU 02 PRESSURE UNIT PSI or bar Fics The default
6. r Temperature unit C External temperature NB Due to the waterproof nature of the housing stabilisation of the temperature reading may take several minutes 24 Hour Clock Note Permanent back light function to activate the permanent back light press Bt1 and Bt 2 simultaneously Do the same to turn off the permanent back light The permanent use of the back light uses excessive battery life so its usage is recommended at night only COPYRIGHTS LDL TECHNOLOGY JANUARY 2010 P11 VURE WEI YGA LITE TIRE PRESSURE MONITORING SYSTEM FIG 2 TURN THE DISPLAY ON AND OFF Ea ON gt short push on Bt1or Bt 2 temperature displayed after 10s The display is waiting for Ids reception OFF gt long push on Bt 2 or automatically turn off after 6mn caused by no wheel unit sensor transmission FIG 3 CHANGING THE DISPLAYED MODE FIG3 Pressure is the standard display mode To display Temperature gt short push on Bt 2 To return to the pressure display gt push again shortly on Bt 2 C FIRST USE OF THE DISPLAY FIG 9 MENU 06 FRONT amp REAR TIRE IDENTIFIER ID SENSOR RECOGNITION The first time the display is powered up it has to verify the unique ID of the front and rear tire the unique ID s are pre programmed during manufacture not allocated to a position and have to be confirmed now to the display Turn ON the display short pushon Bt 1 or Bt 2 rice ID symbo
7. t is active FIG 12 LOW BATTERY DISPLAY ALERT Fis 12 Battery symbol is blinking to inform you that you have to change the battery of the display PANASONIC OR MAXELL CR2450 only COPYRIGHTS LDL TECHNOLOGY JANUARY 2010 P14 VURSS LLL YGA LITE TIRE PRESSURE MONITORING SYSTEM FIG 13 NON PERMANENT LOSS OF COMMUNICATION Fis 13 In case the receiver does not receive the signal from the sensors dashes will be displayed instead of pressure temperature value If the problem is permanent please contact your distributor FIG 14 WHEEL UNIT SENSOR LOW BATTERY ALERT Fic 14 The pressure information blinks alternately with Lo symbol to inform you that the sensor must be replaced Ask your distributor Note In winter conditions disregard this message below 8 C 46 F external temperature H HOW TO MOUNT YOUR DISPLAY FIG 15 HANDLE BAR MOUNT See Page 2 for component description 1 Place the display in the desired place on the handle bar 2 Secure display with the enclosed screw kit n 12 3 Attach the display and insert the CPA clip n 8 The display is now secured FIG 16 BODY MOUNT 1 Drill the body and attach the bracket with screw kit n 13 2 Attach the display and insert the CPA clip n 8 3 The display is now secured COPYRIGHTS LDL TECHNOLOGY JANUARY 2010 P15 VURLS LIE Y1GR LITE TIRE PRESSURE MONITORING SYSTEM FIG 17 BAND MOUNT 1 Ins
8. t least be inflated at 1 bar Fes From ON gt extended pushon Bt 1 until FIG 9 display is seen To launch ID learning gt short push on Bt 2 ID symbols blink Drive more than 20 Mph until Pressure values are displayed time out 4 minutes G RECOGNIZE THE DIFFERENT ALERT MODES FIG 10 PRESSURE THRESHOLD CROSSING ALERT FIG 10 When the display receives lower pressure information compared to the programmed thresholds the alert starts during the first 3 minutes the red led blinks alternating with bar symbol arrow pointing to the faulty tire then bar and arrow symbol will flash until new tire inflation backlight on during 3 minutes to see the alert at night drivings To display tire temperature during alert gt short pushon Bt2 The display will return automatically to pressure alert after 10 seconds FIG 11 TEMPERATURE THRESHOLD CROSSING ALERT A high temperature threshold is programmed at 80 C for front tire and 90 C for rear tire and cannot be changed When the display receives upper pressure information compared to the programmed thresholds the alert starts C symbol arrow of the faulty tire are flashing until the tire comes to a lower value than the programmed threshold To display tire pressure during alert gt short push on Bt 2 The display will return automatically to temperature alert after 10 seconds Note Pressure alert has priority even if temperature aler
Download Pdf Manuals
Related Search