(SAVE THESE INSTRUCTIONS)
Contents
1. A O Condition BUCK Max boost 13 of input On Normal Off voltage for output regulation while input voltage is from 12 to 22 under nominal Off Max buck 12 of input Normal Off voltage for output regulation while input voltage is from 10 to 17 over nominal Utility Failure The UPS is providing battery power to the Battery Power Supplied outlets Utility Failure The UPS is i providing battery power The Normal rapid beeps indicate the battery will run out of charge within a few minutes Overload Occurs in the Full time Surge Protection Outlets Please beeps or turn the UPS off and unplug at On Off On Off Blown Si least one piece of equipment from beeps the UPS Replace the fuse with a spare one then turn the UPS on Overload Occurs in the Battery power Supplied Outlets Normal Lon Turn the UPS off and unplug at On Off On Off Blown Been least one piece of equipment from the UPS Check the fuse and do the replacement if necessary Turn the UPS on Off Off On Off Off For more information visit eu cyberpowersystems com or contact TECHNICAL SPECIFICATIONS Capacity VA Capacity Watts Input Input Voltage Range OP500TE 220 240Vac Frequency Range 50 60 Hz Output On Battery Output Voltage On Battery Output Frequency Overload Protection Simulated Sine Wave at 230Vac 7 50 Hz On Utility Fuse On Battery Internal Current Limiting Surge Protection and Filtering L2. 50 60Hz outlet Contact Cyber Power Systems at Contact Cyber Power Systems at sales cyberpower eu com Turn the UPS off and unplug at least one piece connected equipment Unplug the power cord of the UPS then remove the fuse compartment beneath the power inlet of the UPS and replace Fuse is blown due to overload the blown fuse with a spare one Lock the compartment back to the UPS Connect power Outlets do not cord then turn the UPS on Make sure that your provide power to spare fuse meets the specification 6 3A 250V equipment 5x10mm Turn the UPS off Wait 10 seconds and then turn the UPS on Mechanical problem Batteries are discharged Allow the unit to recharge for at least 4 hours Unit has been damaged by a Contact Cyber Power Systems at surge or spike sales cyberpower eu com Connect the serial cable to the UPS unit and The serial cable is not an open serial port on the back of the connected computer You must use the cable that came with the unit PowerPanel Plus es pat a is connected to Tiy another serial port of your computer is inactive all icons are gray fe ii Shutdown your computer and turn the UPS off A S NOL PTEVISINO JatETY Wait 10 seconds and turn the UPS back on p This should reset the unit The serial cable is not the cable You must use the cable included with the unit that was provided with the unit for the software DEFINITIONS FOR ILLUMINATED LED INDICATORS On Off On Off
3. OE CyberPower eu cyberpowersystems com Office Tower Series UPS OP350TE OP500TE User Manual K01 0500E00 01 SAFETY WARNINGS SAVE THESE INSTRUCTIONS This manual contains important safety instructions Please read and follow all instructions carefully during installation and operation of the unit Read this manual thoroughly before attempting to unpack install or operate your UPS This equipment can be operated by any individuals with no previous training The socket outlet shall be installed near the equipment and easily accessible During the installation of this equipment it should be assured that the sum of the leakage currents of the UPS and the connected loads does not exceed 3 5mA Attention hazardous through electric shock Also with disconnection of this unit from the mains hazardous voltage still may be accessible through supply from battery The battery supply should be therefore disconnected in the plus and minus pole at the quick connectors of the battery when maintenance or service work inside the UPS is necessary Do not dispose of batteries in a fire the battery may explode Do not open or mutilate the battery or batteries released electrolyte is harmful to the skin and eyes Do not replace the batteries INSTALLING YOUR UPS SYSTEM UNPACKING Inspect the UPS upon receipt The box should contain the following UPS Unit PowerPanel Plus Software Disk x 1 Serial Interface Cable DB 9 x 1 Telephone Cable
4. ar from the date of original purchase Any warranty services please contact your local dealers or distributors
5. ightning Surge Protection Network Protection Physical Total of UPS Receptacles Maximum Dimensions Yes RJ45 One In One Out 23 8cm 8 0cm 13 7cm Weight Kg Battery Sealed Maintenance Free Lead Acid Battery User Replaceable Typical Recharge Time 12V 4AHx1 12V 4 5AHx1 Yes Hot Swappable Battery Pack 8 Hours Warning Diagnostics Indicators Audible Alarms Environmental Operating Temperature Operating Relative Humidity Communication Power On Using Battery Boost Buck On Battery Low Battery Overload 32 F to 95 F 0 C to 35 C 0 to 95 NON CONDENSING PowerPanel Plus Windows 98 ME 2000 NT XP Server 2003 Software Auto Charger Auto Restart USB CyberPower Systems B V Flight Forum 3545 5657DW Eindhoven The Netherlands TEL 31 0 40 2348170 FAX 31 0 40 2340314 E MAIL sales cyberpower eu com CyberPower Systems Inc USA 4241 12th Avenue East Suite 400 Shakopee MN 55379 U S A Tel 1 952 4039500 Fax 1 952 4030009 E MAIL sales cyberpowersystems com Entire contents copyright 2004 CyberPower Systems B V All rights reserved Reproduction in whole or in part without permission is prohibited PowerPanel and PowerPanel Plus are trademarks of CyberPower Systems USA Inc CyberPower warrants to you the original purchaser that CyberPower UPS will be free from defects in design assembly materials and workmanship for two years battery is only one ye
6. nput voltage Buck Indicator This LED indicates that the UPS is operating in automatic voltage regulation mode When the led is illuminated continuously it indicates that input over voltage and that O the UPS unit bucks the voltage The UPS provides battery powered and surge protected outlets for connected equipment to insure temporary uninterrupted operation during a power failure and against surges and spikes gge oT The UPS provides surge protected only outlet for connected equipments against I surges and spikes Serial Port to PC This port allows connection and communication from the DB 9 serial or USB port on cers the computer to the UPS unit The UPS communicates its status to the PowerPanel Plus software This interface is also compatible with the UPS service provided by Windows 98 Windows ME Windows NT Windows 2000 Windows XP Windows Server 2003 Ethernet RJ 45 Network Protection Ports These ports are the protection for your computer network cable rio TROUBLE SHOOTING Problem Possible Cause Solution A Recharge the battery by leaving the UPS The UPS does not Batteries are not fully charged plugged in perform expected runme Battery is slightly worn out w nee plished is nee The on off switch is designed to prevent damage by rapidly turning it off and on The UPS will not The unit is not connected to an The unit must be connected to a 220 240V furncon AC outlet
7. r printers vacuums space heaters or other large electrical devices should not be connected to the UPS Please make sure that the total loads of your equipments are less than the maximum total power load of your UPS Bi PLUGIN 2 Use your computer power cord to connect the UPS to a wall outlet Please avoid using extension cords and adapter plugs To maintain optimal battery charge leave the UPS plugged in at all times Your Compuie s Power Cord 3 Press the UPS power button to turn it on The Power On indicator will be illuminated in Green 4 Install your software and accessories To use the software simply connect the enclosed serial interface cable to the serial port on the UPS and an open serial port on the computer BASIC OPERATION FRONT PANEL AND REAR PANEL DESCRIPTION Power Switch Press the power button to turn the UPS ON or OFF Power On Indicator Ta This LED is illuminated when the utility condition is normal and the UPS outlets are m providing clean power free of surges and spikes ON Using Battery Indicator This illuminates during utility failure indicating that the battery is supplying power to USING the battery power supplied outlets BATTERY Boost Indicator 7 This LED indicates that the UPS is operating in automatic voltage regulation mode O When the led is illuminated continuously it indicates that input under voltage and that Boost the UPS unit boosts i
8. x 1 Power Cord x 2 User Manual PowerPanel Plus Software User Manual HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT 1 Insure that the equipment plugged into the battery power supplied outlets does not exceed the UPS unit s rated capacity 350VA 200W for OP350TE 500VA 300W for OP500TE If rated unit capacities are exceeded an overload condition may occur and cause the UPS unit to shut down or the circuit breaker to trip 2 If the power requirements of your equipment are listed in units other than Volt Amps VA convert Watts W or Amps A into VA by doing the calculations below Note The below equation only calculates the maximum amount of VA that the equipment can use not what is typically used by the equipment at any one time Users should expect usage requirements to be approximately 60 of below value TO ESTIMATE POWER REQUIREMENTS 1 ss Watts W x 2 0 VA or Amps A x 230 ___ VA 2 Add the totals up for all pieces of equipment and multiply this total by 0 6 to calculate actual requirements There are many factors that can affect the amount of power that your computer system will require The total load that you will be placing on the battery powered outlets should not exceed 80 of the unit s capacity HARDWARE INSTALLATION GUIDE 1 Connect the equipment to your UPS outlets The IEC IEC power cords coming with the unit are used to connect your computer and monitor to the UPS Items such as copiers lase
Download Pdf Manuals
Related Search